Search Documents

By S. Acar, P. Somasundaran

Results of selective flocculation of natural ores containing two or more minerals and of synthetic mineral mixtures do not usually agree with what is expected on the basis of the results from single mineral tests (Acar and Somasundaran, 1985). This is mainly due to the ionic species released by the minerals, which act differently under different pH values. The objective of this investigation was to study 1) the surface chemical composition of selected sulfide minerals-natural chalcopyrite and pentlandite and synthetic covellite, millerite, and pyrrhotite-and 2) the changes brought about by the dissolved mineral species. Electron Spectroscopy for Chemical Analysis (ESCA) was used to perform the surface analyses.

Jan 1, 1991

By John A. Herbst

At the last Comminution Symposium a challenge (Meloy and Williams, 1992) was issued to "predict the typical straight-line, self similar" tumbling mill product size distributions using a population balance model (PBM). Implicit in this challenge is the assumption that the PBM is inadequate for predicting real world grinding performance. This response is presented in three parts: I. Theoretical analysis of the general PBM and its appropriateness for comminution system modeling. II. Examination of the accuracy of prediction of real world milling behavior using linear and nonlinear PBMs. III. Evidence from recent microscale comminution research. This paper concludes with recommendations concerning future research which will: 1. further elucidate mechanisms of particle destruction and creation as well as attrition and 2. increase the accuracy of model predictions in highly nonlinear situations

Jan 1, 1997

By R. M. Wheeler

For years the blasting industry has recognized eight milliseconds as the minimum delay time interval required between charges in order for them to be considered to fire independently of each other. However, computer analyses of seismic recordings made of several surface mine blasts reveals that this time interval may not always be sufficient for adequate vibration separation to occur. In some situations a combination of short delay periods and low frequency vibrations can result in waveform reinforcement. Various analyses of seismic recordings obtained from single hole detonations can be used to predict delay intervals that may enhance or reduce blast vibration effects.

Jan 1, 1987

By William H. Meadows

This information describes the ventilating and methane gas testing procedures utilized during the raising of a mine shaft using a Robbins 81-R drill. An overview of the raise boring process is presented to illustrate the ventilating and gas testing procedures. A mine shaft project, 4.88 m (16 ft) in diameter and approximately 457.2 m (1500 ft) in length, will be the focal point of the presentation, with reference to similar projects for additional comments on variations in procedure.

Jan 1, 1980

By R. Mira, S. Rosa, P. Souza

This paper shows the historical data, local geology and mineralization, the mining methods applied, current production,, the planning staff, the resources of hardware and software available and the computer methods used. The activities are described starting with the driving of ramps/research levels, their dimensional parameters and positioning, driving of production sublevels with the same parameters plus those concerned with the stability of the rock mass during the development and the mining itself. Then, the detailing of the ore body is described together with the stopes planning, the openings stability analysis, and the drilling patterns and explosive types are discussed.

Jan 1, 1998

By Brian H. Kaye

Efficient design of grinding circuits for efficient production of ultrafine material requires rapid feedback of information concerning the fineness of material leaving the grinding device Generating this information requires efficient sampling and adequate rapid characterization of the material leaving the grinding machinery Recent developments in electrooptic inspection of dry and wet material leaving a grinding device are critically reviewed New methods for characterizing ultrafines are discussed A rapid operating automated cybernetic (intelligent) permeability device for automatic control of grinding circuits using Blaine Index and other fineness indices is described

Jan 1, 1983

By H. Pieterse, K. S. Fraser, J. R. Goode

The Goldstrike autoclave plant is designed for the pressure oxidation of 1363 t/d (1500 stpd) of refractory gold ore. The plant was commissioned in early February 1990 over a one week period - an unusually short period for a plant of this complexity. The rapid plant start-up is attributed to certain detailed design and control aspects of the plant. This paper discusses key features of the autoclave plant with emphasis on the design of the splash/flash system of heat recovery and the control systems. Commissioning and plant operations over the first three months are reviewed.

Jan 1, 1990

By Heiskanen K., Koivistoinen P.

A common belief is that autogenous grinding suits itself only to certain oretypes. It is shown that properly designed autogenous grinding can be used even with very difficult ores with energy consumptions which are equal or lower than obtained with rod-ball mill grinding. The basic feature in the design is the large port grate developed by Outokumpu. The scale-up of the mills can be done on the basis of the base mill concept. It enables to compare different mill sizes and types. Simple scale-up equations are presented based on actual mill data and experimental work.

Jan 1, 1992

By W. M. Shaver, R. Letourneau, W. R. Dengler

Dynatec Mining Limited contracted to sink a 1500 metre (4960 ft.) concrete lined shaft for Falconbridge Nickel Mines in Sudbury, Ontario, Canada. The shaft is 6.3 metres (20.5 ft) in diameter inside the concrete lining and is equipped with steel furnishings. Dynatec used the owner supplied 4.6 metre (15 ft.) diameter double-drum hoist to sink the shaft with 12.5 tonne buckets for muck removal and 4 cubic metre concrete buckets for concrete placement. One of the unique features of the shaft sinking operation is the use of a four-boom electric hydraulic drill jumbo permanently mounted in the shaft sinking stage. This paper will describe the performance obtained with the electric hydraulic drilling equipment and the high capacity muck removal and concreting equipment.

Jan 1, 1991

By Kuda R. Mutama, Allen E. Hall

A wind tunnel investigation into the fundamental characteristics of jet fan performance is described. The effects of varying fan positioning in a square tunnel cross section are reported for two fan outlet diameters and velocities. Tests were conducted, also for a jet fan placed in a flow developed by an external fan operating in the same direction as the jet fan. The position of the jet fan relative to the tunnel walls was found to affect its performance. Performance parameters were determined and used to formulate theoretical equations based on momentum and energy considerations. The results identified a range of flow ratios which can be used to design an effective jet fan ventilation system and provide a basis for the selection of jet fans for practical mining applications

Jan 1, 1997

By R. J. Snow, S. N. Bhattacharya, D. D. Patil

Electrokinetics involves the movement of charged particles or water molecules in an applied dc field. Applications in particle fluid systems include the dewatering of soils, the densification of mill tailings and the treatment of coal wastes. In this paper, a novel application of this technique is discussed, wherein an electric field is applied to a coal-water slurry flowing through a pipe, resulting in lower pressure losses in the system. A unique experimental setup was designed and built to study the effect of an electric field (dc) on the wall shear stress for the flow of coal-water slurry through the pipe. The effect of solids concentration, current strength and pH on drag reduction across the system was quantified.

Jan 1, 2002

By R. J. Sweigard, M. Rohatgi

Differential settlement on reclaimed land presents a particular problem when the land is to be used for row crops. The poorly drained depressions caused by differential settlement restrict crop yield, resulting in additional costs to alleviate the problem. Potentially more serious is the threat of failing to meet target yields due to settlement-related reductions. Because the mechanism by which the problem occurs is not well understood, a physical model study was conducted to investigate the importance of several factors. The importance was considered of such factors as the relative amounts of rock and unconsolidated overburden in the undisturbed condition and the size distribution of rock fragments. But the analysis concentrated on the causes of settlement in the reconstructed soil layer above the rock spoil.

Jan 1, 1991

By Myles P. Reilly, Randall A. Snowdon, John Temporal, O&apos

The paper describes studies made at the Transport and Road Research Laboratory, UK, of the mechanical cutting characteristics using disc cutters, of rocks with compressive strengths up to 340 MPa. These studies have been performed in both the single pass mode, where interactive breakout occurs between adjacent grooves on every pass of the tool, and the multiple pass mode, where several passes may be required to cause breakout. In addition, experiments to determine the effect on cutting performance of the hydraulic stiffness of tunnelling machines are described. The results of these tests are analysed and discussed in the context of the design of full-face tunnelling machines.

Jan 1, 1983

By Betty L. Gibbs

Using a PC can help an operator analyze data more effectively and respond quickly to changing conditions. The cost of microcomputers is low, and fit into the budget of even small mines. Many software packages are also low cost and general software such as spreadsheet, word processing, and data base management programs can help the small miner organize and evaluate information very quickly. A basic hardware configuration is proposed, including hardware upgrades and general and technical mining software packages. The hardware and software suggested can be used by very small as well as larger operations. PC's can be incorporated into all phases of a mining operation at a minimal cost and capabilities can be expanded as the operation grows.

Jan 1, 1987

By D. Greene

The close integration of mine planning and mine operation continues to be the goal of mine operators. Depending upon the complexity, size and sophistication of the mine, limited success has been achieved in this area. Despite tremendous strides in the development of computer-aided mine planning, digital plans must usually be converted to error-prone paper maps and physical ground surveys for actual excavation and reclamation. However, advances in global positioning systems (GPSs), operator displays and mobile computers now enable equipment operators to work directly from on-board digital plans. A computer-aided earthmoving system (CAES) offers reduced survey costs, faster field transition time and improved excavation accuracy, coupled with faster, more informed decision making regarding key mining operations.

Jan 1, 2000

By B. K. Mishra, R. K. Rajamani

This paper focuses on the use of a numerical tool known as the discrete element method (DEM) to study the motion of ball charge in ball mills. DEM is employed to simulate the motion of individual balls. While doing so, the effect of liner design on the grinding performance of the mill is studied. Two important, factors, such as the configuration of the liner and the geometry of the lifting surfaces, are correlated with the overall mill performance. An attempt is made to show the effectiveness of the lifter bars in transmitting power from the mill shell to the interior of the mill, with particular emphasis on large diameter mills.

Jan 1, 1994

By Ernest L. Ohle

Since the first recorded discovery of lead in southeast Missouri near Fredericktown about 1720, knowledge of the deposits has advanced in spurts as a result of outlying discoveries: 1864 Bonne Terre 1890 Flat River, Desloge, Leadwood 1948 Indian Creek 1955 Viburnum The original discoveries at Bonne Terre consisted of residual galena in clay, similar to that in the previous finds at Fredericktown. Occurrences in solid dolomite were not noted until mining of the clay pits exposed the walls of the weathered depressions. The St. Joseph Lead Co. had been established to conduct the operations and it was J. Wyman Jones, first president of St. Joe, who at that time brought about the first of the technological advances that were to occur in the district. He proposed use of the newly invented diamond drill to explore the bedrock showings, after observing the machines in the Vermont Marble Belt.

Jan 1, 1991

By George W. Poling

Designing optimal placer gold recovery plants requires a detailed knowledge of the size, shape and surface physical characteristics of the gold particles and the host alluvium in the pay gravel, sand or clay. Results of a recent pilot-scale study of the quantitative performance characteristics of riffled matted sluice systems are presented. For the appropriate non-coherent pay gravel-sand with medium-flat gold, simple sluices can recover gold at greater than 85% efficiency down to 100pm diameter. Alternatives to simple sluices are presented and discussed briefly.

Jan 1, 1987

By B. Salopek, D. Rajkovic, D. Rumenjak

Among other types of sustainability indicators, linguistic variables have been proposed. During the past few years considerable effort for using the fuzzy logic and linguistic variables (LVs) in environmental decision-making for the mineral industry has been made. The linguistic variables defined could, among others properties, describe the property of acceptability for environment for various environmental indicators. Some proposals for construction of such variables are based on administrative decisions from environmental impact assessment procedures for mining, which provide information for acceptability of quality kind for environment (e.g. obtained from public participation, experts, environmental administration). The measures of evidence for construction have to be based on sets (not only on the members of sets). The administrative decisions with their statements and explanations could be considered as such sets. The measures of evidence appropriate are plausibility and belief measures. Using the more elaborated methods from the theory of evidence, the better estimation of those measures could be achieved. The methods of constructing the linguistic variables, previously suggested and based on obtained measures, are also discussed.

Jan 1, 2011

By S. K. Kawatra

Various types of mathematical descriptions of the flotation process are used in the design of a full scale flotation circuit. Mechanistic descriptions developed under controlled laboratory conditions establish theoretical residence time requirements. Empirical models, describing flotation performance as a function of full scale operating variables, are established from one flotation system and applied to another hypothetical system. Problems of design by mechanistic modeling, such as scale up factors, can be alleviated if the model is developed from a full scale flotation circuit. However, the numerous uncontrollable variables encountered in a full scale operation would preclude the practical application of such a model. Incorporating empirical relations into the full scale mechanistic model will facilitate its effective use as a guide for flotation circuit design. A semi-empirical model has been developed that promises to offer a more effective means of flotation circuit design.

Jan 1, 1982