Search Documents

By M. McPherson, P. Mousset-Jones, G. Danko

Calculation of the sensible heat transfer between the rock surface and the flowing air in an underground airway is still fraught with problems. There are only a few results available in the literature for the calculation of the convection in tunnels with naturally rough surfaces. Some of them are purely empirical, while others use a theoretical approach, based on the analogy between heat and momentum transfer, expressing the heat transfer coefficient as a function of the friction factor. A review and evaluation of these results are presented. The heat transfer equations obtained using the different assumptions, vary over a wide range, so that experimental results are needed to determine the formulae and constants applicable to mine airways. In situ measurements of the "physical" and "technical" heat transfer coefficient carried out in deep mines are described. The statistical distribution of the convective heat transfer coefficient on rough surfaces, as well as the regression between the Nusselt and Reynolds numbers in the turbulent flow region, are presented. Radiative heat transfer between the surface and the moist air flowing in a duct of relatively large hydraulic diameter has been taken into account during evaluation. The results will be a definite refinement of those calculations presently used in mine climate simulation models.

Jan 1, 1987

By R. V. Ramani, R. Srikanth

A three-part study was conducted to relate the dust generation propensity of a coal sample, defined here as the dust generation rate (grams of dust generated per tonne of coal broken), to its characteristics, in order to rank coal seams according to their respirable dust generation potential. In this paper, the results of a single breakage study on a variety of coal samples encompassing all coal ranks, and samples from operating mines are discussed. Further, where data are available, the primary dust generation rates of coal samples collected from underground coal mines are compared with the in-mine dust generation rates. The results of this analysis are then used to apply the results of this study to longwall face ventilation design. Vitrinite reflectance, and level of organic metamorphism are highly correlated with primary respirable dust generation rates of bituminous coal samples. The dust generation rates in underground coal mines are an order of magnitude higher than the primary dust generation rates in the laboratory. Depending on the type of coal, production rates, and dust control procedures, the air quantity required for airborne dust control can vary significantly. The air quantities on some high production longwalls are approaching the limits beyond which it may not be possible to reduce ambient ARD concentrations to less than 2 mg/m3 by dilution ventilation alone. In these cases, the miner's exposure should be controlled through the use of personal protective de- vices and administrative practices.

Jan 1, 1997

By Kevin DeSomber, Scott Bird

Larger grinding mills continue to utilize large gear-driven drives or electrical wraparound drives. The panel will include presenters from operations with large mechanical and electrical drives. JIM HANDLEY: Before we get to the third and final session, I want to introduce my co-conspirator for this session, John Mansanti. John is manager of milling with Newrnont Gold Company, Carlin, Nevada, and was very active in securing participation in this innovative symposium. I'm Jim Handley and I'm with Cyprus-Amax Minerals at the Sierrita copper and molybdenum mine. Our third presentation is titled "Geared Up or Wrapped Up?" I hear this topic discussed, but never at great length. I think that's because the opinions are fairly strong and diverse, and people generally aren't reinforced properly in their arguments. The first person to enlighten us on this topic is Scott Bird. He has more than 20 years with Kennecott, is a graduate in metallurgical engineering from the University of Utah, and is currently operations superintendent and deals with this phenomenon every day.

Jan 1, 1998

One of the largest mining shows in the world is set take place April 15-18 in Santiago, Chile. Expomin 2008 is expected to attract more than 60,000 professionals from around the world who are involved in all aspects of the mining industry. Expomin has become an important place for mining leaders to meet, organizers said, ?with great expectations for the development of new business in international markets.? This is the 10th Expomin. The event, held every two years, is expected to at-tract exhibitors from more than 25 countries, representing nearly 1,000 companies and more than 3,000 brands related to the mining industry, organizers said. Most all of the world?s largest equipment manufacturers and suppliers ? surface and underground ? will be represented. The importance of the event to the Chilean and international mining industry can be seen by the increase in size of the exhibition ? 13 percent more surface space in 2008, compared with the 2006 Expomin. The exhibit will be broken down into four pavilions, covering 34,054 m2 (355,570 sq ft). An outdoor area for the large mining equipment will cover 16,120 m2 (173,520 sq ft).

Jan 1, 2008

By W. W. Simpson, S. A. N. Sheya

A procedure was developed by the U.S. Bureau of Mines for recovering gold, silver, cobalt, copper, and zinc from a massive sulfide ore by a hydro-metallurgical process. The procedure consists of (1) oxygen pressure leaching; (2) iron, arsenic, and copper removal from the leach solution by precipitation; (3) selective extraction of cobalt and zinc from solution; (4) electrodeposition of the cobalt and zinc from the strip liquor; and (5) cyanidation of the pressure leach residue to recover gold and silver. The results are discussed in terms of efficiency of metal recovery and conclusions drawn as to possible benefits and broad applications of the process.

Jan 1, 1990

By Michel Grenier, Mahendra Gangal

Two methods used to measure the exposure of mine workers to diesel exhaust particulate were compared. One method was developed by the U.S. Bureau of Mines and the University of Minnesota's Particle Technology Laboratory. The method which was originally developed for use in coal mines is a size selective sampling technique. The other method uses an “ashing" approach to assess the exposure to diesel particulate. This second method is based on the principles of sampling according to the ACGIH respirable dust sampling criteria and the use of a silver membrane filter as collection substrate. Because a silver membrane filter is used, both respirable combustible dust (diesel particulate) and respirable silica can be measured from one sample. The comparison study took place in a Canadian lead-zinc mine during tests which were primarily designed to evaluate the gaseous and particulate emissions characteristics of new diesel engine technology. The study has shown that under the test conditions encountered, some differences were observed between the results as obtained by the two methods. These differences seem to depend on the characteristics of the respirable dust found in the work- place, i.e., size and composition. The impact, on sampling and analysis of diesel particulate, of the proposed guideline (ACGIH) for a TLV® of 0.15 mq/m3 is discussed briefly.

Jan 1, 1997

By Charles W. Daugherty, Robert Nyren

The replacement of Boston’s elevated Highway I-93 running north to south through the heart of the city with 8-lane tunneled roadways, coupled with the underground extension of Highway I-90 eastward to Logan Airport, has earned the Central Artery/Tunnel (CA/T) Project the position of the largest infrastructure project in the U.S. today. The gigantic interchange featuring numerous ramps where these two main branches of the Artery intersect required the construction of three huge jacked tunnel boxes that were pushed beneath eight active Amtrak and commuter rail tracks that had to remain undisturbed in spite of poor geology and a minimum of cover between the track beds and the tunnel crowns. Ground freezing was chosen as the method of stabilizing the soil over the tunnels, and it was extended in one area to stabilize the ground at the intersection between the tunnels and an abutting deep cut-and-cover excavation. Because many standard geotechnical instruments consist basically of open standpipes filled with water, it was a major challenge to keep them de-iced and in a condition to provide data on vertical and lateral ground movements. The efforts to do so are herein described.

Jan 1, 2003

By M. Dosemeci, M. McCawley, J. McLaughlin, Z. Wu, F. Hearl, W. Blot, K. Peng

Proposals have been made by two organizations, the International Standards Organization (150) and the American Conference of Governmental Industrial Hygienists (ACGIH) for a revised respirable dust criteria and criteria for thoracic and inspirable dust. These criteria yield different results than criteria based on lung deposition patterns in assessing the hazards due to dust exposure. Since these differences are a function of the size distribution of the dust an analysis of dust size distributions from various mining operations was performed to determine the amount of difference that could occur. The dust size distributions available for this analysis were taken from U.S. coal mines and from Chinese metal mines. The mass of mechanically generated dust that will deposit in the alveoli was found to be in direct proportion to the ISO/ACGIH criteria estimates in the mines studied. Therefore, respirable dust estimates for substances such as coal and silica are not a problem. Estimates of exposure to diesel exhaust in these mines, however, were not always in the same proportion to the estimated alveolar deposition. Also, concern with an excess of bronchitis among miners may not be adequately addressed by the use of samplers conforming to the ISO and ACGIH criteria. The cascade impactors used to acquire the data for this analysis require four to eight substrates per sampler. For daily dust exposure assessment this method is cumbersome and time consuming. Therefore, two new samplers have been designed to meet the need for determination of deposited dust mass. These samplers follow the lung deposition curve rather than the penetration curves proposed by the ACGIH and ISO and require analysis of only two substrates per sample.

Jan 1, 1992

By William Highton

If the economic situation in the Western World evolves on a path similar to that of the past decade, then we Mining Engineers must accept that one of the major cost factors in the production of deep mined coal is going to be that of labour. Whilst not trying to over-simplify matters it does appear that one of the ways of maintaining acceptable coal costs is by obtaining more coal without increasing manpower. One such way could be an increase in the use of the retreat method of mining. The paper theorises and illustrates case studies to show that as the Mining Industry extends the use of Longwall retreat mining systems in coal seams where the risk of spontaneous combustion exists, then the use of bleeder entries should be questioned. In addition to the spontaneous combustion risk, bleeder entry systems where the ventilation flow is not fully controllable cannot be construed as a safe and reliable method of controlling high rates of methane emission. These two major aspects alone should be sufficient ground for Mining Engineers to re-consider the practice of using bleeder entries. An alternative "The Back Return System" appears to offer most of the advantages for controlling the environment, without the disadvantages of the other system.

Jan 1, 1980

By F. N. Kissell

The Bureau of Mines used sulfur hexafluoride (SF6) tracer gas to evaluate the effectiveness of gob ventilation and/or sealing practices at three coal mines, each having different problems associated with their mined-out areas. The purpose of these ventilation studies was to better understand whether current techniques employed for ventilation or sealing are successful at minimizing the potential for gob fires and explosions. The work performed at each mine is discussed: One is a longwall operation that uses ventilation to carry off hazardous gases, and two are room-and-pillar operations, each with far different concerns, that seal off the gobs to isolate them from the main mine ventilation. In all cases, employment of the Bureau's SF6 tracer gas technique resulted in answers to questions raised by the mine operators concerning the effectiveness of their gob ventilation or sealing practices in preventing mine fires.

Jan 1, 1987

By G. T. Adel

The selective recovery of fine particles by flotation has been a long-standing problem in the mineral processing industry. Fundamental studies carried out at Virginia Tech since 1980 have suggested that many of the problems encountered in separating fine particles can be alleviated by using significantly smaller air bubbles than those used in conventional flotation processes. The main advantage of using smaller bubbles is found in an increased recovery rate, which can be attributed to an improved bubble-particle collision efficiency. This concept has been applied in column flotation as a means of improving flotation kinetics. A computer simulator has been developed to better study the effects of various parameters on flotation column performance. The simulation results suggest that the use of small bubbles and tall columns improves the recovery of fine particles while a judicious use of wash water greatly improves product quality. Information collected as a result of this analysis has been applied in developing scale-up relationships for column flotation.

Jan 1, 1989

By S. F. Hillis, J. E. Rourke, K. A. Szalay, O&apos

INTRODUCTION For the past 25 years, tunnel support requirements have frequently been determined, at least in North American practice, by classifying the rock according to the system proposed by Terzaghi (1), using one or more of the 8 Rock Conditions which he defined, the rock load then being selected within the range given for each Condition. However, there is a lack of published data comparing Terzaghi loads with actual measured rock loads, and it would appear that the degree of conservatism, or otherwise, of the Terzaghi approach is very often unknown. Excavation of 4 large diameter tunnels at the Tarbela Dam Project in Pakistan afforded an opportunity to compare Terzaghi and measured loads, through instrumentation of the steel ribs installed for temporary support, and by classification of the geology exposed during the tunnelling operations. In addition, the deformation of the rock surrounding the tunnels was monitored during excavation by means of borehole extensometers installed prior to the start of tunnelling. This paper describes the tunnel instrumentation and the results obtained therefrom, and relates these results to the Terzaghi load coefficients. It also discusses the effects of the methods of excavating the tunnels on the rock loads and rock deformations. PROJECT DESCRIPTION The Tarbela Dam Project is located on the Indus River in

Jan 1, 1974

By A. E. Hall, D. M. Mchaina

This paper outlines a proposed research project to investigate secondary sulphide ignitions. Sulphide dust explosions have resulted in loss of production and considerable capital and equipment replacement cost in Canadian mines. The practical application of laboratory test results to actual mine situations presents a complex problem and is a field requiring immediate investigation. The factors contributing to the outbreak of sulphide ignitions are not clearly understood. This indicates a need for future research to study the influence of blasting parameters, exhaust temperatures, and dust characteristics on secondary ignitions at source. The aim is to establish realistic quantities for each of the parameters and develop a model that will incorporate field and laboratory quantities. It may be possible to predict outcomes of sulphide ignitions when the parameters are known. It is also planned to study the techno-economic feasibility of the preventive and control methods. One aspect of planned future research requires quantification of some terms by obtaining measurements of pollutant concentrations and size distribution of the airborne dust in an underground environment immediately after a main blast. A blast-proof aerosol sampling package to measure the source term will be designed. This sampling package will consist of a sampling section and a shield which will be capable of withstanding a blast explosion. The accuracy in measuring the variables and combination of variables will be the main focus in this proposed study.

Jan 1, 1987

By Ernest Koenigsberg

In 1961 Lerchs and Grossman presented a method, based on graph theory, to determine the optimum ultimate pit limits for an open-cast mine. At the same time they demonstrated a dynamic programming algorithm for the optimum pit limits for a two-dimensional open-cast mine. Since then many methods for determining optimum limits for three-dimensional mines have been programed, and even more have been reported in the literature. The methods include computer "simulation" of the manual methods used by engineers, the development of sets of conic sections and fitting to exclude overlap, integer linear programming (and its equivalent network flow model), and dynamic programming. Many of the methods do not guarantee optimal solutions but seem to satisfy the user. Other reported methods have never been applied, partly because they did not yield optimal solutions. We have developed a three-dimensional dynamic programming algorithm which requires a single pass through the data. Large problems can be solved on a small computer because only a small part of the data is required at any time. In this paper we will review the state of the art and to demonstrate the connection between linear programming (and network flow) models and the dynamic programming method.

Jan 1, 1982

By Fred N. Kissell

Work done by Foster-Miller Associates under a Bureau of Mines research contract has developed methods to increase significantly the amount of fresh air that reaches the front of a continuous-mining machine. The emphasis was on removing methane build- ups that occur at the cutterhead. Using a full-scale plywood mockup of a coal mine working face area, the study showed that in many instances only about 20 pct of the fresh air heading towards an exhaust brattice or tubing actually gets to within 1 ft (0.3m) of the face. The key to providing more air at the face is to enhance and move forward the natural airflow pattern. This change in the natural airflow pattern can be accomplished by taking advantage of the air-moving abilities of the conventional water spray. It was discovered that if all the water sprays on the machine were realigned, then ventilation efficiencies of 70 pct or more were achieved regularly. This meant that if 9,000 cfm (4.2 m3/s) was entering the brattice, at least 6,300 cfm (3.0 m3/s) of this was reaching to within 1 ft (0.3m) of the face. This water spray realignment consists of placing a few nozzles on the side of the machine opposite the curtain and also tilting the front sprays slightly towards the curtain side. Recently, two underground tests and two additional independent laboratory tests of the water "Spray Fan" have been completed. In general, they have confirmed the performance of the Spray Fan system, but they also have provided useful information as to its difficulties and limitations.

Jan 1, 1980

By Peikun Liu, Guangyu Sun, Raja V. Ramani, Shambhu Sharan, Raman Srikanth, Bharath K. Belle

The contribution of the various outby sources to the contamination of the panel intake air has been the subject of a relatively small number of studies. In this paper, after a brief review of past studies, results from recent experiments on rates of contamination of intake air by outby dust sources are presented. Present study indicates that each outby source by itself may not be a major contributor. The loading point in the continuous miner section did not appear to be of major concern from contamination point of view. Belt entry including transfer point contributes significantly to the intake air dust level, though reentrainment was not a major source of dust. In longwall panels, the stageloader-crusher was the most dominant source. The panel-to-main belt transfer point was not a major source. Taken collectively, the contribution of all outby sources can be significant. In one longwall section, at the beginning of the longwall face, the contribution of all the outby sources and the headgate cut-out operation was observed to be about 80% of the permissible exposure limit (2 mg/m3). In modem high production longwalls, the application of effective dust control measures to reduce the dust generated from the outby sources is essential to achieve compliance with the dust standards.

Jan 1, 1997

By Shallesh K. Patel, Richard M. Powers, Patrick Zhang

Perceived environmental impacts from flotation reagents used in the phosphate industry have been of concern for nearly a decade. A research program was initiated to determine the distribution, fate, and consequences of flotation reagents (fatty acids, fuel oils, and amines) within the environment. Therefore, laboratory investigations of biodegradation and soil attenuation of the reagents were conducted along with field flotation mass balances and groundwater investigations in clay settling, sand tailings, and undisturbed areas. Sample analysis and a reagent mass-balance model indicated that most reagents are distributed in clay settling and sand tailings areas. Groundwater analyses showed no fatty acids or amines in any of 19 surficial or intermediate aquifer water samples. In contrast, fuel oils were detected in the surficial aquifer at all sand tailings areas in concentrations ranging between 8.5 and 0.5 mg/L. Fuel oil was also detected in trace amounts (0.6 mg/L) in one intermediate aquifer well located in an active sand tailings area. All fuel oil concentrations detected were very low and, coupled with a biodegradation rate of approximately 10% per month, all concentrations should be within reference levels in six months. Based upon the results of this study, use of flotation reagents in the beneficiation process of the Florida phosphate industry present no long-term threat to the environment.

Jan 1, 1999

A number of factors have resulted in the widespread use of computer simulation as a day to day tool in the mineral processing industry, as is the case in most engineering disciplines. A number of simulation packages, both steady-state and dynamic are now available commercially. The developers of such software face an enormous challenge in maintaining and improving the packages due to the complexity inherent in such systems. This problem known as the software crisis faces all developers of complex software. Object-oriented (OOP) and design is a methodology which has been developed to try and minimise this problem. The use of the OOP paradigm in the devlopment of simulation software for mineral processing systems is explored in this paper and it is found that OOP techniques have major benefits for the design and development of such software.

Jan 1, 1992

By Hans Breuer

The new regulations for the bituminous coal mining industry, issued by the mining authorities of the Federal Republic of Germany, are aimed at reducing to a feasible minimum any development of the coal workers pneumoconiosis (CWP) by lowering the admissible dust exposure of mine workers. Additional and improved measures of dust suppression and job assignment control *) are required for the purpose In this connection two basically different demands are placed on dust measurements: As far as dust suppression is concerned, the causes of dust development and the effectiveness of methods applied to reduce dust concentrations have to be identified, whereas with regard to the control of job assignment, the dust exposure of mine workers has to be depermined. Demands placed on dust measurements -- specifically for determining dust exposure -- are liable to become more severe since the threshold limit values were considerably reduced in these last years and since any additional dust suppression measures as well as a purposeful job assignment to certain mine workers are dependent on relevant measuring data. Therefore, research work has been carried out with the objective of measuring and evaluating, in terms of their effect (i. e. their incidence on the development of a CWP), size distribution, concentration, and specific noxiousness of any prevailing dust conditions.

Jan 1, 1980

By J. F. Stenebråten, W. P. Johnson

Carbonaceous material (CM) from the Barrick Goldstrike Mines, NV, was characterized with respect to its gold sorption (preg-robbing) and gold recovery behavior. The breadth of graphite peaks measured by X-ray diffraction were used to calculate crystallite dimensions (002) of the CM. The (002) dimension was found to vary inversely with preg-robbing activity and directly with gold-recovery behavior, indicating that the degree of graphitization (maturation) experienced by the carbonaceous material is correlated with gold-loss during ore processing. The inverse correlation of preg-robbing activity was improved when percent preg-robbing was regressed against (002) crystallite size and carbon content. The (101) crystallite dimensions of all samples were calculated from laser Raman analysis, and were not found to correlate with preg-robbing behavior of the CM. BET surface area and micropore size distribution results were affected by grinding history, negating comparison of these characteristics between samples.

Jan 1, 2000