Search Documents

By B. J. Arnold

Coal froth flotation cells typically receive little attention in coal preparation plants. They process only a small portion of the total coal feed (perhaps 5-1 0% of the total plant feed in the United States), they are viewed as a way to take the load off the refuse thickener, and their operation is not well-understood by cleaning plant operators. Operating parameters are set based on the equipment supplier information, and reagent dosages are set at the recommendation of the latest chemical vendor. The cells then operate day in and day out, recovering coal and producing a product that may not meet ash or sulfur specifications or that may be the wrong percent solids for downstream dewatering operations. If improvements can be made to this circuit, then the whole plant will benefit. Paying attention to rate and residence time and the wealth of data from the literature or from a series of targeted laboratory tests can give operators the key to improving the performance of froth flotation cells AND overall plant performance. This paper provides an overview of froth flotation rate and residence time data and gives practical suggestions for specifying and using laboratory tests to improve froth flotation performance. Suggestions for improving froth cell performance are also given based on available literature data.

Jan 1, 1999

By J. C. Reid

Computer-aided lithogeochemistry was used to "prospect" for stratabound scheelite (a tungsten ore) that occurs in many Precambrian clastic and chemical rocks, northeastern Brazil; The district is a metallogenic province covering about 5000km2. Exploration bedrock lithogeo-chemistry was applied at regional, local, and mine scales to identify regional tungsten trends and dispersion halos associated with economic tungsten mineralization. Regional coarse-mesh sampling (Cu,Mo,W) in 25km2 cells "found" all major mines and significant prospects using objective and cost objective computer mapping of bedrock geochemical data. The method is efficient ; of the 3600km2 study area only 9% of the original area remained after the initial pass. Of this area, the geo- chemically highest ranked (4%) cells contained the mines and prospects. Similar computer-aided treatment was applied to Cu,Mo,W,F, and Be lithogeochemical data from several mining concessions and prospects with outcropping and subsurface W mineralization. At a local scale out-cropping W mineralization was recognized at a distance of 500m. Fracture zones through which hydrothermal solutions traveled were identified; these were related to W mineralization at a depth of 200m.

Jan 1, 1986

By N. S. Tanious

The accuracy of vibrating wire stress meters has been questioned by various users in the mining industry. During an in situ coal pillar study, a laboratory evaluation program was developed to determine whether stress meters could produce reliable measurements in coal. More than $0 stress meters were tested for accuracy, repeatability, effects of setting pressure, and the concept of using a single curve for interpreting the stress-meter data. The testing medium was lucite, a material with a modulus of elasticity very similar to coal. The evaluation demonstrated that the stress meters did provide repeatable measurements, but that accuracy was lacking when the recommended interpretation technique was used. Therefore, a new technique was developed that required all stress meters to be calibrated in the laboratory before use in the field. This new technique reduced the average error to typically less than 10% and, in the worst case, to below 15%.

Jan 1, 1988

By Osvaldo Bascur, Laurent Garrigues, Nouna Kettaneh, Svante Wold

The chemical, oil, semiconductor, mining, and paper and pulp industries, as well as most other modern industries, are rapidly expanding the range of measurements used to characterize raw materials, process steps, intermediates, and final products. In addition, process variables such as temperature, pressure, and flow become more and more numerous, providing extra information on the state of the process. However, no matter how many sensors are added, the underlying sources of variations that drive the process behavior remain constant. On the other hand, the measuring frequency of these data has increased from once a day or once an hour to once, ten, or even hundred times a minute. This gives masses of data that are swelling in both directions (more variables and more observations). These data need to be properly stored, managed, and analyzed to provide diagnostics about the state of the process as well as an understanding of the relationships between different parts of the process and the product properties. Projection methods such as PCA (principal components analysis) and PLS (projection to latent structures) compress process data to informative summaries of the original variables. These can be shown on line, providing an efficient, graphically oriented suite of diagnostics regarding the "health" and performance of the process. The power of these methods is illustrated by two examples of industrial data in the mining industry.

Jan 1, 2000

By H. Verakis

A fire in a coal mine conveyor belt entry represent a major safety and health risk to miners. Fighting belt entry fires can be a commanding effort. If there is a failure of one aspect in the fire fighting needs such as a dissimilar hose-valve connection, then it can result in the inability to extinguish a fire. Fire incident data compiled over nearly 30 years for underground coal mines shows that fires in belt entries account for 15-20 percent of the total number of fires. Fires in the belt entries of coal mines have resulted in injuries and fatalities. New regulations have been promulgated that require an unplanned fire not extinguished within 10 minutes of discovery to be reported to the Mine Safety and Health Administration (MSHA). A fire that is not extinguished within several minutes may take hours or days to extinguish or may require sealing a section or the mine in some cases. The current fire protection regulations in the U.S. Code of Federal Regulations (CFR), Title 30, Part 75 are designed to prevent or control the fire hazards present in a belt entry. These requirements and other factors affecting belt entry fires are discussed, including fire detection and warning, fire suppression devices, type and location of fire fighting equipment, waterlines, and cleanup and removal of combustible materials. The fire suppression systems used to extinguish/control a belt fire and the effect of ventilation on the propagation of conveyor belt fires are also discussed.

Jan 1, 2009

By Andrzej Wala, Tom Altman, Tom Hughes

The University of Kentucky Mine Ventilation Manager (UKMVM) is a system that contains Level Five knowledge bases and comprises an expert mine ventilation management system. The package uses production rule language (PRL) to interpret data monitored from sensors, e.g., for airflow, temperature, and concentration of gases, in an underground mining environment. Activated from the PRL knowledge bases are Pascal subprograms which (1) organize the monitored data to set up emergency consultations, (2) display graphic representations of a mine's ventilation network with the latest sensor readings, (3) provide interactive updating of mine ventilation parameters, e.g., resistance changes, revised flow requirements, and new regulator and fan settings. Also activated from these knowledge bases are programs which (1) monitor airflow, temperature and gas concentrations from a physical mine ventilation model and (2) adjust regulator openings and fan rpm's. Thus, as an expert system the UKMVM not only presents advisory consultations for underground environmental emergencies, but also serves as an interface between the monitoring and responsive control aspects in the continuous maintenance of normal mine ventilation.

Jan 1, 1989

By Michel Grenier, Gopal Kunchur, Stephen Hardcastle

This paper presents the findings of a dust study in a typical fluorspar processing plant. The primary purpose of this study was to identify employees and occupational groups exposed to high dust levels and determine compliance with personnel regulations for regular and extended work shifts. The range of airborne concentration of respirable silica and fluoride compounds in specific areas and on personnel was determined. State of the art dust monitoring equipment and tracer gas techniques were used to measure dust concentration, pinpoint dust sources and map major airflow trends in the mill. Results of the survey indicated silica dust concentrations in excess of permissible limits being produced mainly by crushers at the south end of the building. Tracer gas releases and gas chromatographic analysis further showed that prevailing south to north air currents tended to carry and spread dust produced by the crushing operations throughout the process plant. Airborne concentrations of fluoride compounds measured during the study were always well below the prescribed threshold limit value (TLV) for the contaminant. Recommendations, including a mechanical exhaust ventilation system on crushers and transfer points, scheduled preventive maintenance on existing bar sprays and wearing of personal protective equipment were made which significantly improved the work environment. Further testing conducted after Installation of the dust extraction system revealed significant improvements in most areas of the mill.

Jan 1, 1991

By J. Cheung, H. Rabia

The traditional methods for predicting mine air temperatures are based on steady state heat transfer models as developed by Voss (1969) and Starfield (1983). These models are useful in providing approximate predictions of air temperatures in trunk and gate roadways. More complex models are required to provide predictions along faces. In practice, the heat flow in underground mines is of transient nature and recent observations in some British Coal mines show temperature variations of up to 5°C during a working week at any one point. In addition, the recent introduction of district recirculation of mine air in British mines requires a more precise prediction of air temperatures during start up of the system or during breakdown. A transient heat transfer theory based on the work of Jordon is presented. The method lends itself easily to computers due to the large number of calculations involved. The proposed transient model is validated using actual temperature data collected in roadways in Wearmouth Colliery in the North East of England. The transient results are compared with the steady state predictions of Voss (1969). Finally, predictions of air temperature in roadways for a recirculation system will be made using both the transient and steady state models. Temperature predictions along faces will be made using a separate model.

Jan 1, 1989

By C. Babbitt, J. O’Green, N. I. Jayaraman

In many mines, dust-laden air from an entry being driven by a continuous miner will contaminate the intake air to the roof bolter operator and other downwind personnel. Through a US Bureau of Mines (USBM) contract, Foster-Miller Inc. has evaluated several control techniques to reduce the respirable dust exposures of downwind personnel. One fan and tubing technique consisted of bypassing the miner-generated dust directly to the section return. The results of the evaluation of this technique revealed that reductions in dust concentrations of 90% or more can be achieved at downwind roof bolter locations. A second method was to clean the dusty air from the upwind continuous miner by using a dust collector. The cleaned air was then supplied to the bolter through collapsible tubing. An underground evaluation showed reductions of 82% to 96% when the dust collector was operating. A third method was to reduce the quantity of dust contributed by the miner to the return airstream. A water-powered scrubber was installed over the throat area of the continuous miner. More than 1.18 m3/s (2500 cfm) of dusty air moved through five tubes with dust collection efficiency exceeding 75%. Underground evaluation results showed that return dust concentrations were reduced by about 60%. This paper discusses the ventilation and dust control techniques used for personnel downwind of the continuous miner.

Jan 1, 1987

By K. Holmberg, D. Herriot

This paper by Mr. McIvor is yet another contribution to the eternal controversy surrounding the benefits, or otherwise, of high circulating loads in closed circuit grinding. Throughout the paper it is difficult to establish whether the author is referring to effects relating to the mill, classifier, or to the overall circuit. Table 1 is put forward as indicating the advantage of operating at high circulating loads. From the two (it would be interesting to see more) product sizing points provided in each case, the conclusions to be drawn are that cases one and two have very similar size analyses. The third case, however, indicates a much flatter curve, that is to say, higher fines production and a very wide spread of size ranges. If the objective of this circuit is to provide a closely sized product with minimum overground slimes to the downstream process, then it would appear to be the less "efficient" by far. No data is given for product pulp densities either. The term "efficiency" should never be used without a careful and clear definition. In this case, "efficiency" is used to express an apparent percentage reduction in operating work index (Bond) from the measured "standard" at 250% circulating load operation. The Bond calculation is itself based upon

Jan 1, 1990

By J. A. Brierley, C. L. Brierley, R. C. II Blake, S. McGinness

A principal long-term goal of this laboratory is to achieve a detailed understanding at the molecular level of the microbial-dependent solubilization of minerals. Three recent advances in this research are summarized. (i) An in situ electrolytic procedure is described whereby large quantities of autotrophic iron-oxidizing organisms may be achieved for fundamental or applied studies. Over 600 grams wet weight of Thiobacillus ferrooxidans were harvested from a single 55-gallon growth vessel. (ii) A basis is presented for classifying some 70 different iron-oxidizing bacteria into one of 4 categories, depending on the type of redox-active electron transport proteins expressed during aerobic respiration on reduced iron. Comparative spectroscopic analyses indicated that different electron transport mechanisms exist in different genera and species of acidophilic bacteria that respire on iron. (iii) A method is introduced to investigate the binding interaction between bacteria and minerals, based on changes in the electrokinetic properties of the two species. Preliminary experiments indicated that the electrophoretic mobilities of pyrite and Thiobacillus ferrooxidans were both altered when the two colloid particles were mixed prior to the actual electrokinetic measurement. The need for more basic information regarding all aspects of the microbial-dependent solubilization of minerals is evident.

Jan 1, 1993

By J. J. Moore

Combustion synthesis, or self-propagating high-temperature synthesis (SHS), reaction systems are discussed with respect to thermodynamics and kinetics. In particular, the effect of the process parameters, e.g. particle size, [All] ignition and combustion temperatures, on these self-sustaining reactions is discussed. Combustion theory is used to investigate the effect of the overall actuation energy of the SHS reaction on the combustion front propagation rate and in obtaining a clearer understanding of the transition from stable to unstable propagation. Finally, examples of the application of combustion synthesis to advanced materials processes are made, in particular the synthesis of Ni-Ti-X intermetallic shape memory alloys, TiC-AI2O3 and ZrB2-AI203 ceramic composite materials.

Jan 1, 1992

By Joseph Renk, David Akers, Glenn Shirey

Each year, US coal cleaning plants landfill or impound millions of tons of high-quality, fine-sized coal. This coal is not only difficult and expensive to capture during cleaning, but, if captured, can pose serious materials handling problems. The GranuFlow. Technology was developed and patented by the U.S. Department of Energy (DOE) to address these problems. GranuFlow involves the addition of a coal binding agent such as an asphalt or heavy oil emulsion to coal to reduce moisture, dusting, and freezing and to improve the flow properties of the coal in bins and chutes (1, 2, and 3). When the emulsion is added before mechanical dewatering, the binding agent causes the formation of fine-sized coal agglomerates that dewater better than untreated coal. In addition, the binding agent increases the capture of ultra-fine coal in screen-bowl centrifuges. Previous work by DOE has also demonstrated that such treatment results in a significant reduction in dustiness and a reduced potential to freeze. To address concerns about the handling and combustion characteristics of GranuFlow treated coal, DOE performed a pilot-scale pulverization and combustion test (4). No problems were encountered during pulverization or combustion, and use of this fuel in a p.c. boiler was found to be feasible from a technical perspective. CQ Inc. has an exclusive license from DOE to market this technology and is currently performing a series of commercial demonstrations to determine if GranuFlow is both technically and economically viable.

Jan 1, 2005

By Alice Blount, F. Patrick Carr

The quantitative evaluation,of quartz and other minerals in acid-insoluble residues from carbonate rocks and other industrial mineral products derived from sedimentary and low-grade metamorphic rocks is difficult. Commonly there are a dozen or more minerals present, and the suites vary from sample to sample. Because of these factors, either the absorption coefficient must be determined on a sample to sample basis or an internal standard must be used. Internal standards in general use are unsatisfactory. For example, [A1203] is often present in product samples because of ceramic grinding elements used in their production; CaF and LiF have peaks which overlap or nearly overlap mineral peaks in the samples. A careful evaluation has shown that magnesium aluminate (synthetic spinel) works particularly well as an internal standard for these types of samples. Not only does it have few, strong diffraction peaks which do not overlap, the peaks are in the same 28 region as the minerals, usually quartz and silicates, for which quantification is desired. Spinel also consists of equidimensional particles without prominent cleavages; this promotes a random orientation of the minerals in X-ray diffraction mounts. In addition, spinel can be used to correct for loss of diffracted-beam intensity due to thin sample preparations which are often unavoidable.

Jan 1, 1991

By A. W. Scaroni, C. Y. Tsai

The effect of particle size and composition on the pyrolysis and combustion of a pulverized bituminous coal in an entrained-flow reactor has been investigated. Predicted time-temperature histories of the coal particles and experimental weight loss data indicate a strong coupling of heat and mass transfer to the pyrolysis and combustion rates. A higher combustion rate following ignition was observed as particle size was increased to 112 µm (about 140 mesh). This is related to a higher particle temperature after ignition for the larger particles. Although the heating rate before ignition decreases with increasing particle size, higher slip velocities and surrounding gas temperatures for the larger particles promote early ignition. The presence of liptinite in the coal increases the weight loss rate before and immediately after ignition. Similar behavior was observed for pyrolysis. Fractions of an HVA bituminous coal that were rich in mineral matter or semi-fusinite were found to have a higher heterogeneous char combustion rate than vitrinite-rich samples.

Jan 1, 1987

By Malcolm Scoble, Sean Dessureault, Scott Dunbar

Budgets are key financial and behavior drivers for most businesses, including mining. Budgets are used to link strategic objectives to tactical decisions, to measure performance, and to provide basic financial planning. More accurate and pertinent budgets should result in improved strategic decision making and performance measures. This paper discusses how a process based production and cost database, based on activity based costing models and the one year production plan, can be used to create the annual budget for an operating mine as an Activity Based Budget (ABB). A case study is used to compare budgets derived from traditional methods and an ABB approach. It is evident that the ABB method is more accurate.

Jan 1, 2002

By M. B. Díaz Aguado

Traditionally, the practical evaluation of a mining project for a potential investment has been made considering mainly technical aspects. But the concept of sustainable development has introduced significant changes in the factors analyzed to make the final decision. This paper proposes an empirical evaluation of a project considering not only technical, economic and financial parameters, but also associated risks and other intangible aspects, such as political considerations, stability in the legal frame, social factors and environmental issues. The proposed methodology is practical and easy to apply for project management. Among its main advantages, the following could be quoted: using this evaluation two different projects or locations of a same project can be compared, future behaviors could be predicted, the index incorporates a new approach to specific mining projects and this perspective could also be applied to other projects with environmental and social impact, such as civil works or industrial projects.

Jan 1, 2007

By M. R. Stokes

Over the recent years there has been an increase in the application of retreat mining on longwall faces as mine operators strive for ever greater productivity. The purpose of this paper in then to review current practice as a starting point and then move forward to discuss the future geometry's that a longwall face may take. Single and double production zone three roadway faces are assessed. All possible configurations of three roadway faces are defined. Unsuitable configurations are rejected after analysis of broad ventilation issues. The remaining configurations are then assessed on an operational basis, this includes: limits on retreat synchronisation, structure of centre gate, floor bulging and equipment installation. The remaining viable configurations are then further assessed on ventilation issues, this includes: provision for gas control/gas fringe, face climate and balancing of face flows. Possible face climate is assessed using numerical simulation of the various configurations, the predicted dry/wet bulb temperature and predicted levels of heat stress indices are given and discussed in detail, along with face flow balancing. The necessary conditions required for the successful operation of a double production zone three roadway face system are formulated, together with conclusions as to the possible level of application.

Jan 1, 1997

By D. A. Rice, R. G. Swanton, A. May, O. C. Carter

As part of a cooperative effort between the US Bureau of Mines and the Florida Institute of Phosphate Research (FIPR), with input from the phosphate industry, the conversion of phosphogypsum to sulfur is being investigated. The proposed process incorporates a thermal reduction of phosphogypsum to calcium sulfide (CaS) and a hydrometallurgical treatment to convert calcium sulfide to ammonium bisulfide (NH4SH), which is then oxidized using a catalyst to produce elemental sulfur. The paper summarizes the results of continuing laboratory studies using an activated carbon catalyst which was loaded with sulfur through oxidation of ammonium bisulfide solution. The extraction of the sulfur that forms in situ on the catalyst is a key area in the development of the sulfur recovery process. Two approaches for removing the sulfur are being investigated: (1) thermal treatment to volatilize sulfur. and (2) leaching the sulfur using liquid anhydrous ammonia. The research has shown that it is technically feasible to recover over 90% of the sulfur from the carbon by either volatilization or ammonia leaching. Locked cycle testing has demonstrated that the carbon has the potential to be recycled after ammonia leaching.

Jan 1, 1987

By D. V. Professor Keller

The production of premium coal-based fuels (<3% ash) and ultra clean coals (<1% ash) using the process of selective agglomeration requires proper selection of raw coal, rough preparation procedures, milling equipment, product coal size distribution, water purity, agglomerants, agglomeration equipment and operational procedures. Each of the variables can contribute a small fraction to the impurity load in the product coal or limit the ability of the process to separate mineral matter-free coal. Each of the variables and their importance will be examined from data produced at the bench by batch and continuous agglomeratons as well as the results from pilot plant and tonnage production units. The results are discussed which have indicated that some standard commercial coals can be produced with ash contents as low as 0.2 % ash (batch/bench) and several tonnage lots of 0.6% ash in as 200 lb/hr pilot plant. In most cases iron pyrite released from the coal matrix and with proper pH control is rejected from the product coal agglomerates.

Jan 1, 1995