Search Documents

By Keith G. Wallace, Malcolm J. McPherson

In order to model accurately a mine ventilation system in an existing mine, it is necessary to determine the resistance to airflow in all main airways. This is accomplished by measuring the airflow and pressure differential in each airway. Gauge and tube methods have been used to determine pressure drops in ramps and level airways. However, it has rarely been used in evaluating the frictional pressure drop in shafts. Because shafts commonly have the highest pressure loss in mines, it is critical that the resistance of these airways be determined accurately. This paper describes the theory and practice of using the gauge and tube method for determining the pressure drop in shafts. The pros and cons of using this method are discussed as well as a comparison between the gauge and tube and barometer measurement techniques. Case studies showing the accuracy of shaft gauge and tube measurements are also presented.

Jan 1, 1991

By Wang Yingmin, Xu Zhuyun

There are 3 steps in the process of forming a mine ventilation system, (1) selecting a reasonable ventilation pattern (included pit shaft arrangement); (2) optimizing of the ventilation network and (3) computing and outputting the flow splitting results of the network with the optimal ventilating equipments selected. In the past, the first step was relied on artificial decision-making. In order to design a common ventilation system, some ventilation experts were needed to participate or do some examinations. Even so, the design made was reasonable only for those experts. If there is a mistake in the first step, then even the followed 2 steps are best done, the losses are very difficult to retrieve. So that, the first step is very important. The development of expert systems provided an efficient means and tool for all engineering fields. This paper presents an expert system of selecting mine ventilation pattern and pit shaft arrangement. After testing many times, it is shown that the system can perform the first step of designing a mine ventilation system, and can help the experts doing their study works more efficiently.

Jan 1, 1991

By Raghoottama S. Pandurangi, Mohindar S. Seehra

A critical examination of the published results on the hemolytic ability of different forms of silica viz, quartz, cristobalite, tridymite and amorphous silica is made and it is concluded that quartz, cristobalite, and tridymite have nearly equal longterm abilities (within ±15%) but much larger than the hemolytic ability of amorphous silica when correctly compared on a per unit surface area basis. Also, a one-to-one correlation appears to be valid between the hemolysis and fibrosis studies. New results on the photoacoustic spectroscopy of amorphous silica particles heat-treated at 100, 200, 400, 550, 700, 820 and 1050°C are presented and it is observed that the intensity of the sharp silanol band at 3745 cm-1 and hemolysis by these particles have nearly the same temperature dependence. In contrast the intensity of the bulk IR modes (viz. the 797 cm-1 band) does not show any significant temperature dependence. These observations demonstrate that the surface SiOH species are involved in hemolysis by silica particles. Key words: silica polymorphs; hemolysis; silanol species

Jan 1, 1991

By John O. Marsden

The project development metallurgist is faced with an interesting dilemma: The use of overly conservative metallurgical projections and cost estimates can kill a project that has the potential to provide needed jobs and growth to a company's bottom line. On the other hand if the metallurgist uses a highly aggressive approach by trimming capital and operating cost estimates to the bone and by applying highly optimistic metallurgical projections, there is a risk of creating a project that can never live up to expectations. The metallurgist must walk a tightrope between "sandbagging" and "overoptimism," and this tightrope is fraught with political intrigue and difficulty. This paper takes a some- what lighthearted look at some of the political aspects associated with this issue, and other issues, and offers a few guidelines for walking the "political metallurgical" tightrope.

Jan 1, 2001

By J. H. White

It is hypothesized that the Hotelling valuation principle (HVP) can determine the value of developed gold reserves using simple methods and easily obtainable data. This paper reports the results of an empirical test of this hypothesis. The model for the HVP is given by [V R=Cp-0(1) or V - CP-0' R(2)] where p = current spot price of gold per oz, [c] = average extraction cost of gold per oz, V = current market value of the gold in the ground (dollars) and R = gold reserves (oz). Using publicly available data from North American gold companies, we obtained data for V, R, p and c, and we ran a simple linear regression using Eq. (1) as the definition of the dependent and explanatory variables. By examining the value of the coefficients of the resulting regression equation, we can draw conclusions as to whether or not the HVP can be confidently used as an estimator of the value of developed gold reserves.

Jan 1, 1997

By Stephen J. Brower

Located in Central Nevada, The Round Mountain Gold deposit has been continuously mined since 1977. Present proven and probable reserves are 226 Mt (250 million short tons) at 1.1 g/t (.032 oz per short ton). The current open pit mining rate of 118 Kt (130,000 short tons) per day is producing 41 Kt (45,000 short tons) per day of ore to be processed by heap leach methods. At this rate, the current reserves provide a 16 year mine life. The high mining rate and strict ore delivery requirements mandate comprehensive and realistic mine planning. The mine planning process is described in three general steps: Deposit Modeling; Mine Design; and, Production Coordination and Support.

Jan 1, 1989

By Lei Chen, Michael L. Free, Ravindra Bhide

The incorporation of particles into metal matrix materials is important to many technologically important areas. Particles that are incorporated into a metal matrix have a significant effect upon the properties of the resulting composite. Proper selection of particles and incorporation densities can lead to optimal composite properties that can be modified as needed for various applications. This paper discusses the parameters that affect the particle incorporation density in electrodeposited metal matrix composite coatings as well as a deterministic model that can be used to predict the effects of such parameters on particle incorporation density.

Jan 1, 2003

By R. N. Chakravorty, R. J. Kolada

Explosions of methane in coal silos and coal ships is an ever present hazard. Recent investigations have shown beyond question that considerable accumulations of methane do occur in coal storage silos and numerous recent explosions in coal transport shipping strongly indicates that the same conditions also exist in ship storage holds. Investigations have shown that the main concentrations of methane occur within the actual coal pile. Within this region normal silo and ship ventilation systems are ineffective. The main 1ine of defence is therefore to exclude potential sources of ignition or to place the coal in an inert atmosphere, or both. This paper presents the results of a methane survey of all operating silos in Western Canada. These results demonstrate that a serious and widespread hazard of explosion exists. This paper also discusses various methods by which this hazard may be reduced including methods of venti1ation, inertization, microbiological control and early warning systems.

Jan 1, 1987

By K. Rajamani, I. Shah

The development of liquid-level control algorithms, based on sets of linguistic rules expressing human operator's "intuitive" control strategies, have been reported. The main objective of the present paper is to illustrate the implementation methodology. The experimental work was done with a 28.3Lflotation cell. The control variable (height of pulp in the cell) was controlled by manipulating the outflow rate. The controller algorithms were programmed and implemented using an Applelle computer and a Keithley das Series 500 measurement and control interface. It is pointed out that the scheme of fuzzy controllers is simple to use and powerful enough to handle complex and nonlinear systems.

Jan 1, 1987

By G. D. Trump, F. L. Stanley

Spirals have become one of the most popular methods for treating fine coal. Unfortunately, spirals tend to produce an undesirably high specific gravity cut point and often misplace significant amounts of coal and/or rock. In the present study, a process-engineering tool known as linear circuit analysis was used to identify problems with traditional spiral circuits and to suggest alternative configurations. These analyses indicate that a modified rougher-cleaner circuit incorporating a middlings recycle stream offers the best option for improving performance while maintaining a reasonable circulating load. In light of this finding, a full-scale test circuit was installed and evaluated at an existing preparation plant. Data obtained from the plant tests indicate that the new spiral circuit can simultaneously reduce the cut point and improve separation efficiency. Preliminary economic analysis show that the new circuit provides an attractive payback on capital investment.

Jan 1, 1999

By R. V. Ramani, R. A. Jankowski, R. Bhaskar

The spatial distribution of airborne dusts, deposition of dust in the airway, as well as the effect of airflow velocity and particle density on dust behavior in mine airways were studied in a set of experiments performed in a mine airway under controlled conditions. Considerable deposition of dust near the source was indicated. Pronounced effects due to velocity were observed in ambient dust concentration and deposition along the mine airway, both in the respirable and the total size ranges. Cross-sectional concentration measurements indicate an increase in concentration from the roof to the floor. The average cross-sectional concentration is about 75% of the concentration in the center of the airway.

Jan 1, 1987

By Jürgen Lotze

Previously (1981), it was shown that the fiscal policy practised by some IBA-member countries is mainly responsible for a significant shift of known bauxite resources into higher processing-cost categories. The possible impact of politically imposed fiscal costs on the competitiveness of relevant bauxite resources is investigated in detail by means of a model calculation procedure.

Jan 1, 1984

By Dick Lewis

The Misima deposit is on Misima Island in the Lousaide Archipelago, 240 km east-southeast of the Papua New Guinea mainland, and 600 km east of Port Morseby. Misima is a narrow mountainous island 40 km long and up to 10 km wide. The highest point is 1035 m above sea level. Gold mineralization is restricted to the eastern and less rugged third of the island. The Melanesian population lives in coastal villages. Subsistence agriculture is the main activity, although copra and cocoa are grown in plantations on the eastern and southern coasts. Prior to 1950, mining was important in the economy of the island. Climate is tropical, with little seasonal variation in temperature or rainfall. Tropical cyclones occur about every 10 years (Fig. 1).

Jan 1, 1990

By Y. L. Su

This paper describes a case study where solutions were sought to the truck queuing that occurred at a central processing plant. Ore from three production shafts at Falconbridge Limited's Sudbury Opera¬tions is hauled by three trucking contractors to Strathcona Mill. On return trips, the classified mill tailing is carried back to the mines for backfilling. The ore feeder at the mill handles three times the tonnage designed for and the situation is not expected to improve. Excessive truck queuing and consequent mine production interruptions are therefore of great concern. During the study, stochastic models were formulated and programmed for the IBM/AT personal computer. Basic information sought from the models were truck waiting time and ore production interruptions. The existing system was tested, not only to verify the validity of the models, but also to understand the causes of the problem. Several alternatives were simulated and a simple solution selected for implementation.

Jan 1, 1986

By E. D. Dainty, B. E. Enga, D. L. McKinnon

Following considerable laboratory studies concerning particulate control systems for underground use, a program was commenced to develop practical real life implementation systems. This program covers the implementation in seven mines of particulate filter systems to 10 engine models from three engine manufacturers in 12 different vehicle types, a total of 24 vehicles. As the program ran, one mine had to drop out and a mutually agreed upon system could not be arrived at for another. Hence, the program included five Canadian mining companies. Several of the vehicles trialed at Brunswick Mining were trialed by Brunswick themselves. Nonetheless, the data is presented. This paper covers the work performed from the beginning to the end of the demonstration program. Data collected to properly select and design filter systems along with technical conclusions of the demonstration are presented. Also presented are the results of a survey that highlights the participating mines' acceptance of the technology.

Jan 1, 1991

Over the last two decades, the mining industry has spent considerable time and effort in installing sophisticated control systems (including expert systems) to regulate and improve the performance of AG/SAG mills. Yet the need for these systems is often overlooked – unmeasured and uncontrolled variation in the feed material. With AG/SAG mill technology replacing rod and ball mills as primary grinding equipment, the need for careful and thoughtful feed preparation has gone. To maximise mill throughput, operations need to better understand the ore characteristics affecting AG/SAG mill performance. Industrial operating data will be used to illustrate these ideas and concepts. It is often quite surprising which ore characteristics that are the most influential on mill throughput.

Jan 1, 2004

By M. J. Virnig, B. D. Boley, G. A. Wolfe, J. M. W. Mackenzie

A flowsheet for the recovery of nickel and cobalt from laterite ores was developed. The flowsheet involves acid leaching followed by hydroxide precipitation of the metal values and then releaching of the hydroxide cake with ammonia. Investigations of the chemistry of extraction of nickel by LIX® 84-I and a developmental reagent, XI-84-IT, along with the physical properties of the organic phases are described. Based on these investigations, suggestions with regard to design of a solvent-extraction plant and operating conditions were made.

Jan 1, 2002

By S. C. Bandis, N. Barton

During drilling of deep boreholes, local mechanical failures of the wellbore walls may occur due to the inability of the incompetent overburden and reservoir rocks to withstand drilling-induced changes of the stress environment. At present, borehole failure mechanisms in three-dimensional stress fields are poorly understood. Our experimental investigations based on 3-D physical models demonstrate the stabilizing effect of the intermediate principal stress. The latter may play a dominant role in maintaining the integrity of the stress relieving failure zone around the borehole. However, this will depend on the stress anisotropy, the angle of hole deviation and on the angle of internal friction. Our tests also indicate that the failure zone can accomodate high extensional strains. Finally, relations between the physical models and closed-form elasto-plastic solutions are discussed.

Jan 1, 1986

By Stephen G. Whittaker, Rosalind A. Schoof, Martha J. Steele

In determining remedial action objectives for metals in soils, the U.S. Environmental Protection Agency typically assumes that the metal concentrations in house dust are the same as the metal concentrations in soil. Data now available from several studies that were conducted in mining communities suggest that for some metals, concentrations in house dust may be lower than those in soil. This paper reviews available data on the relative soil and indoor dust concentrations of arsenic and cadmium and examines how changing assumptions regarding indoor dust concentrations of arsenic affects risk assessments and determination of cleanup levels.

Jan 1, 1992

By J. H. Lalor

The Olympic Dam deposit was discovered in July 1975 with the intersection of 38 m (125 ft) of 1.05% copper in diamond drill hole RD 1. A further eight holes were drilled with only marginal encouragement to November 1976 when RD 10 cored 170 m (558 ft) at 2.12% copper and an economic discovery was confirmed. The discovery of Olympic Dam is an excellent example of the application of broad-scale scientifically based conceptual studies to area selection combined with the backing of an exploration management willing to support its exploration scientists in testing their ideas with stratigraphic drilling. It also illustrates the persistence required in mineral exploration. The project began in 1969-1972 with the development of a conceptual model for the formation of sediment-hosted copper deposits. This model suggested that the alteration of continental-type basaltic rocks could release copper into solution from which it could be concentrated in favorable stratigraphic positions. In mid-1972, this concept was applied to a review of the Proterozoic and Lower Paleozoic rocks in South Australia aimed at defining targets for stratigraphic copper deposits.

Jan 1, 1991