Search Documents

By P. Somasundaran, Bruno Lartiges

Two different groups of mechanisms have been considered in the past to explain the effects of chemical additives on grinding. While one group of explanations is based upon alterations of surface and mechanical properties of the individual particles, the other group depends mainly on the arrangement of particles and their flow in suspensions. In this paper some of the past work on grinding aids is reviewed and attrition grinding of a commercially important ceramic material, zirconia (stabilized with yttria) with polyaaylic acid as grinding aid, is studied in order to determine the effect of the aid on the ground product itself. It was observed that even though polyaaylic acid did cause a drastic decrease in the viscosity of the pulp, it did not have any major effect on the grinding of zirconia at least up to 2000 ppm and only minor detrimental effect above it. Importantly, complexation by the polymer was found to cause extraction of yttrium into solution with possibly significant changes in the surface chemical composition of the product.

Jan 1, 1992

By Y. C. Kim, F. Szidarovsky

The technique of linear kriging as a grade estimation method of mining blocks is reason¬ably established in the mining industry. During the kriging process, negative kriging weights ([]i) are sometimes encountered. Due to negative kriging weights, negative block grades may be obtained in some extreme situations, which makes no practical sense. To guarantee nonnegative weights, an additional constraint is required in the kriging system of equations. Unfortunately, the nonnegative weight constraint results in a set of nonlinear system of equations. In this paper, a derivation of the resulting set of nonlinear equations is presented and a numerical algorithm is developed for the solution of the equations. Because the algorithm developed does not remove negative weights arbitrarily, optimal nonnegative weights are always guaranteed. Results obtained using the developed algorithm were compared with those using the standard linear kriging, in terms of computer, time and the estimation results. Both the computer time and the kriging variance were found to be higher with nonnegative constraint, as expected. However, some systematic pattern was observed in the kriged values (i.e., over-or underestimation) with or without the nonnegative constraint. The study also demonstrated when one should generally expect negative kriging weights in practice, and what practical impact the negative weights can have on the kriging estimates.

Jan 1, 1987

By Hassan El-Shall, El-Sayed A. Abdel Aal

The major goal of this study is to decrease iron content in wet-process phosphoric acid. Reducing the amount of post-precipitated sludge in the acid is another important objective in this investigation. In order to achieve these goals, research efforts have focused on bench scale testing of an iron-chelating reagent to remove iron from phosphoric acid produced from South Florida high-iron and -magnesium phosphate concentrate, and plant testing using freshly produced concentrated acids for reducing the post- precipitated sludge. The data obtained in the above studies suggest that the addition point of the precipitating reagent is very important, as the precipitated iron compound has higher solubility at higher P2O5 concentrations. Up to 60% Fe2O3 removal efficiency is achieved depending on the amount of the reagent, concentration of acid used, and operating conditions. The addition of precipitating reagents to freshly concentrated phosphoric acid leads to a decrease of up to 84% in sludge volume percentage depending on acid type and clarification conditions. Decreasing the volume percentage of the sludge facilitates acid handling as well as decreases the adherent water- soluble P205 leading to lower total P2O losses.

Jan 1, 2002

By Hu Wenjun, Li Maonan

Mine ventilation systems mostly are ventilation networks with fixed-quantity branches. The solution to the problem of ventilation networks with fixed-quantity branches is obtained by choosing the fixed quantity branches as chords and using Hardy Cross iteration method. The solution usually is feasible but may be not economical. This paper takes minimal annual ventilation electricity cost as an object, considering the power of main fans and boosters, natural ventilation pressures and resistances of regulators, and builds up a nonlinear programming model. A set of initial values of the nonlinear programming can be obtained by using Hardy Cross method, The MAP technique then used to find a set of local optimal solution The running procedure with a simple example is dicussed. Mine ventilation systems mostly are ventilation networks with fixed quantity branches. In the networks, air quantity of branches are generaly regulated by increasing branch resistance or air pressure. A comon approch to the of the networks with fixed quantity branches is to formulate it based on Kirchhoff's current and voltage laws and the solution is obtained by Hardy Cross iterative technique. The solution usualy is feasible but may be not economical. The optimal plan of air quntities regulation of mine ventilation network should be to make the solution satisfy both required quantity of work places and minimal ventilation operating cost. It is the purpose of this paper to introduce a new approch and computational experience of nonlinear programming of the optimal problem.

Jan 1, 1991

By Michael J. Nicol

Hydrometallurgical processes involve the recovery of metals from ores, concentrates, calcines, mattes and scrap materials by a series of operations involving leaching or dissolution, separation, purification and reduction of metals in aqueous solutions. The underlying theoretical basis of many of these operations is electrochemical in nature and it is the purpose of this review to identify and illustrate, by way of examples from the author's experience and that of others, the central role of interfacial electrochemistry in the understanding, design and control of these operations.

Jan 1, 1993

By Christopher Haycocks

Subsidence induced innerburden shearing and stress fields, whether active or passive, frequently contribute to significant ground control failures in overlying seams. In this paper proven multi-seam technology is used on upper seams to forecast and quantify the magnitude and severity of damage and the increased mining risk due to interaction. Increased upper seam ground control problems are demonstrated using hazard mapping which provides a viable technique for utilizing damage predictions in design.

Jan 1, 1986

By Rudolf E. Greuer, Xintan Chang

Mine fires have always been of great concern to mining engineers and their behavior has been studied for a long time. Although an abundance of observations exist, no satisfactory mathematical model for their interpretation and extrapolation has become known. The paper presented here tries to close this gap, making use of the laws of chemical kinetics, energy and momentum conservation. To overcome the mathematical difficulties, the fire zone is axially divided into segments and radially into sections, each one with an extension of only a few inches. Conditions in segments and sections are updated in time intervals of one second or less. To solve the large number of resulting equations, a numerical solution is performed. The model has so far been tried on timber fires. It confirms experimental observations on the ignition phases and equilibria of these fires.

Jan 1, 1987

By Steven A. Moreno

Geochemical returns from commercial analytical laboratories are often delayed because of postal and other bulk distribution inefficiencies. Consequently, minerals exploration programs are handicapped due to insufficient time for treatment, analysis, and diagnosis of the data. The minerals industry lacks a system for rapid transmission of geochemical data which allows immediate entry into statistical and plotting routines. Over the past three years, Houston International Minerals Corporation (HIMCO) has developed a computer-based system to receive, treat, and distribute geochemical data. In the past two years, Bondar-Clegg (Denver) and Chemex (Vancouver) have developed systems to transmit' data directly to HIMCO via the world-wide Boeing Computer Services (BCS) network. The main benefits to HIMCO have been ten less days for reporting turnaround, ten less days for keypunching, less data handling, accuracy. The benefits to the laboratories have been improved in-house data management, reporting, and HIMCO's increased geochemical activity.

Jan 1, 1982

By R. S. Conti, L. L. Chasko

To deal with an unexpected event such as fire, prevention and preparedness are important elements in an underground mine's strategic plan. The purpose is to prevent afire before it initiates and to be prepared to deal with it when it does occur. This paper highlights a technology that may be used by the mining workforce to minimize such occurrences. It discusses thermal imaging cameras and their many applications to detect equipment failures or hot spots before they develop into afire. It also evaluates the feasibility of using thermal imaging cameras for emergency responders to assist them during exploration, rescue and fire fighting efforts. These thermal imaging systems allow rescue personnel to see in darkness and through dense smoke, thus making it easier to locate heated areas and missing or trapped personnel.

Jan 1, 2003

By Gerhard Mücke

Geothermal and operational reasons in the German coal mining industry make it necessary to an increasing extent to climatize coal faces and headings by means of refrigeration plants. Air coolers installed on coal faces as well as in gateroads play an important part in such climatization. They must transfer, under difficult conditions, the refrigerating capacity supplied by central or de-central refrigeration plants from the chilled water to the air in the workings. The performance data of two new types of coalface coolers and of two different types of gateroad coolers were measured in two testing stations under different thermo- dynamic conditions with dust-free fresh air. As air coolers must be installed particularly at working points with a high .dust load the heat exchanging surfaces are fouled for the most part causing an essential reduction of the refrigerating capacity. The investigations therefore were extended to measurements with a certain dust load in the intake air of the coolers.

Jan 1, 1980

By Richard R. Klimpel, Basil F. Fee

This paper summarizes the status of a series of new chemical reagents developed with the explicit goal of expanding the capabilities of existing froth flotation processes as well as allowing for new solid/solid separations to be undertaken that are not now feasible with flotation. The first portion of the paper briefly outlines the theory and motivation behind the development of each new reagent family. 'The second portion of the paper deals with specific laboratory examples of some separation systems studied to date.

Jan 1, 1993

By B. K. Mishra, R. K. Rajamani, R. Venugopal, P. Songfack

Millsoft is a computer-simulation software that predicts the performance of large industrial grinding mills. This software surpasses all other tumbling-mill analysis techniques available today because it is based on fundamental laws of physics instead of empirical correlations. Graphical user interface (GUI) forms simplify the specification of the following design and operating parameters: mill diameter, length, speed, charge density and size distribution, lifter material and geometry. All of these parameters are taken into account in the discrete element numerical technique that constitutes the essence of the simulation software. In turn, the software produces a visual animation of grinding-charge motion, predicts mill power and gives the distribution of impact energy. In this paper, a case study of an 8.5-m-(28 ft-) diam SAG mill is used to illustrate the application of Millsoft for mill design and trouble shooting.

Jan 1, 2000

By Harrison R. Cooper

Composition data is needed as input for executing process control and management of particulate separation for flotation control. While requirements for composition data can be satisfied in many cases by manual sampling and analysis, automatic sampling and assay systems are now viewed as justified for all but the simplest or smallest processes. On-stream X-ray fluorescence analysis (XRFA) has satisfied requirements for the main portion of metalliferous sulfide ore flotation processes as XRFA technology evolved in reliability and sophistication from its beginnings in the late 1950's. In recent years, advanced on-stream analysis technologies have reached levels of development suitable for use in process control to increase efficiencies of important processes in mining and minerals industries such as coal fines flotation and industrial minerals beneficiation (particularly phosphate beneficiation) where XRFA methods have been inapplicable. Recent technical developments pertinent to use of advanced technologies as well as improvements to established on-stream composition analysis methods are discussed.

Jan 1, 1989

Since first introduced, the coal mine roof rating (CMRR) has been widely accepted as a tool for geologic characterization and mine planning. This paper discusses the application of the CMRR to another practical ground-control problem: extended cuts. Extended cuts, i.e., cuts greater than 6 m (20 ft) in length, are commonly used with remote-control continuous miners. Extended cuts can greatly increase productivity, but they have been associated with a number of fatal roof-falls. When extended cuts are attempted in weak roof material, the roof may collapse before it can be bolted Until now, it has not been possible to predict where conditions may not be suitable for extended cuts. In this study, data on the CMRR and extended-cut experience were collected at 36 mines in seven of the United States. It was found that, when the CMRR was greater than 56, deep cuts were routine in nearly every case. When the CMRR was less than 37, extended cuts were almost never taken, and, when the CMRR was between 38 and 56, extended cuts were sometimes, but not always, feasible. The data also show that extended cuts are less likely to be stable if either the entry span or the depth of cover increases.

Jan 1, 2000

By Barry N. Doyle, Tarcisio M. Carvalho, Alan K. Haines, Marcos P. de Melo, Edward J. da Silva

A metallurgical complex to recover gold from highly refractory arsenical ore was recently commissioned by Sao Bento Mineraco. The plant, with a nominal capacity of 20 000 tonnes per month, is situated in the Minas Gerais province of Brazil. The process consists of run-of-mine milling, flotation, pressure oxidation of the concentrate, carbon-in-leach, elution and electrowinning, and effluent disposal. The paper provides an account of the investigations that resulted in the decision to install the pressure oxidation circuit, process and engineering design and plant start up. A comparison is made between the results achieved during the first two years of production and the design parameters.

Jan 1, 1989

By M. R. Nelson

Continuing experience in the Black Hills, South Dakota, indicates the persistence of several natural contaminants in mine waste effluents under circumneutral pH conditions. Selenium and arsenic are the most problematic environmental contaminants observed in these effluents. The contaminants are present in ore and waste rock as naturally occurring trace elements, and under the physico chemical conditions of the mine waste repositories are mobilized by oxidation and desorption reactions into infiltrating water. Characteristics of the mine wastes, waste repository construction, and Black Hills climatic conditions, indicate these natural contaminants may persist well into the future causing long-term mine closure liabilities, a difficult challenge to both mine operators and regulators.

Jan 1, 2003

By J. F. T. Agapito, J. B. Page

This paper describes part of a geotechnical study based on stress determinations and convergence measurements conducted to assess the long-term stability of an experimental room-and-pillar oil shale mine. A rock mechanics program was initiated in 1971 at the Colony Mine as part of a large study conducted for the design of a commercial operation. The Colony Development Operation is a joint venture currently consisting of four active members; Ashland Oil Inc., Atlantic Richfield Company (Operator of the project), Shell Oil Company, and The Oil Shale Corporation. Although oil shale commercialization plans are presently suspended, rock mechanics instrumentation has been continued as part of Colony's policy in maintaining readiness to proceed with a commercial shale oil plant when national energy policies became better defined. The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 200 miles west of Denver. Experimental mining operations were conducted from 1965 to 1972 with one of the major objectives of the pilot mine being the assessment of opening and pillar sizes for the determination of extraction ratio and life of the property. Mining was conducted in a 60 foot thick portion of the Mahogany Zone in the Parachute Creek Member of the Green River Formation, at depths of 600 to 850 feet by a one-bench system. Pillar dimensions were 58 feet by 58 feet and rooms were 55 feet wide.

Jan 1, 1977

By Jacek Kolacz, Knut Lyng Sandvik

Fine grinding in an air swept and a grate discharge ball mill working in closed circuit with a forced vortex air classifier has been investigated in continuous laboratory scale. Minerals with different physical properties were ground down to 40, 20, and 10 micron top size. The shape of the product particle size distribution curve was investigated and specific surface (BET) was measured. During production of material with top size of 40 microns in an air swept mill, the capacity was up to 25% higher when compared to a grate discharge mill. This difference dropped to 180A during production of 10 micron top size material. A corresponding decrease in power consumption was observed. An important finding is that by regulation of the air flow rate through the mill, it is possible to achieve products with different specific surfaces and particle size distribution curve steepness. During production of the 10 pm material, the specific surface could be varied in the range 3 to 4.5 m2/g. Such powders could hardly be produced in a grate discharge mill because fine particles coated the grinding media and the lining. On the other hand the internal classification in the air swept mill kept the size distribution of the mill content relatively free of fines. This prevented a similar slowing-down of the air swept grinding process.

Jan 1, 1995

By R. Larry Davis

Over the past decade there has been a continual decrease in domestic oil reserves accompanied by a sharp increase in the demand for energy. Even with increased imports of foreign oil, the energy demand has not been met. This has forced many users to turn to substitute fuels. Of the many substitute fuels available most users are turning to and creating an increased demand for low sulfur coal. Because of the increased demand for low sulfur coal as well as the inherent problems in producing eastern coal, many producers have turned their attention to the large deposits of low sulfur coal in the western United States. Western coal mining is, however, not without its problems such as high moisture content, high ash content, highly variable sulfur content, multiple seams, and/or pitching seams. It is to aid in the solution of these problems that this chapter is directed.

Jan 1, 1979

By R. Lindsay Mundell

During the past 12 years, use of longwall methods to mine coal in the United States has continually in- creased. Although these methods offer several advantages, health hazards often exist because of unique and difficult problems in the control of respirable dust. This paper discusses the results of respirable dust studies conducted on United States longwall mining operations in 1972and 1978. Current engineering control methods (ventilation, water application and use of machine cutting parameters) and administrative controls for minimizing employees' respirable dust exposures are discussed.

Jan 1, 1980