Search Documents

By Gianfranco Ferrara, Carlos A. Guimaraes, M. C. Williams, T. P. Meloy

Presented is a method of continuously producing very narrowly sized particle streams. Currently Sieve Cascadography is a batch method of analyzing particle shape - a form of particle chromatography. This paper introduces and analyzes the continuous Sieve Cascadograph, a device that enables a series of narrowly sized particle fractions to be produced continuously. Properly designed, the continuous Sieve Cascadograph will produce many product streams of particles with as little as one percent difference in particle size within a given size fraction - an order of magnitude better than existing technology permits. By varying operating conditions, the size of the output fractions may be varied.

Jan 1, 1992

By H. Sis, S. Chander

The pressure filtration behaviors of dispersed and flocculated alumnae slurries at high percent solids were investigated with the objective of determining the effect of surfactant type and concentration on slurry properties. A high-purity alumina powder was used as a model solid. Dispersion of the alumina was controlled by pH and by surfactants that are known to act as electric and steric stabilizers. The effects of both ionic and nonionic sutfactants were investigated. Surface charge measurements of the slurries were carried out by an electrokinetic sonic amplitude (ESA) method to better understand the mechanisms. The effect of surfactant type and concentration on the kinetics of pressure filtration and cake properties are discussed.

Jan 1, 2000

By V. Prabhu, D. Mantha, R. Reddy

Secondary copper blast furnace slag was treated with carbon to derive the conditions for maximum recovery of copper with a minimum simultaneous reduction of iron oxide. Experiments were carried out to study the effect of temperature, carbon and CaO additions to the slag on the efficient recovery of copper. A two-stage reduction process was also employed to study the efficiency of copper recovery and the results were compared with those of single-stage reduction. The maximum recovery of copper in alloy phase was obtained with 5 % initial carbon in the slag, 2% CaO addition to the slag and at a reducing temperature of 1573 K. Higher grade of the alloy phase with respect to copper was obtained by employing a two-stage reduction process. The results obtained in this study are comparable to those of the earlier research on the recovery of copper from reverberatory furnace discard slags.

Jan 1, 2004

By Sukumar Bandopadhyay

In recent years planning of surface mines in general and reclamation and post-mining land uses in particular have become very complex. Due to the lack of suitable techniques, land use plans are rarely based upon structured decisions. Data collection may be conducted in a rigorous manner and certain analyses may be performed on the data; the decision to put the land to a specific use, however, is finally based upon the intuitive judgment of one or several individuals. This paper demonstrates how techniques from fuzzy set theory can be used in order to select an optimum post-mining land use plan. The various land use planning alternatives have been characterized according to both qualitative information and quantitative factors and the "fuzzy" aspects of the collected information are incorporated into the analyses. In a practical application, the methodology is used to obtain the most reasonable solution to a post-mining land use planning problem in Interior Alaska.

Jan 1, 1986

By L. M. English, Y. J. Wang

When plotted as head vs. volume, fan curves start high and decrease with increasing volume, while mine head curves start low and rise with increasing volume. Their intersection is the system operating point. However, as every ventilation instructor knows, the fact that head loss is a negative number (debit) and fan head is an energy addition (credit) is often a stumbling block to student or audience comprehension since the curves seem to reflect the opposite. It is possible to use the intuitively correct curves- pressure losses as negative values and energy additions as positive values - and still obtain the correct operating point. Adding the two curves produces a third curve that intersects the x-axis at the operating point, the point at which the fan energy input exactly matches air circulation energy loss. Using this technique also makes it easier to account for outside influences on the system, such as natural ventilating pressure. With the standard approach, it is quite easy to add or subtract such influences to the wrong curve. This approach can be extended to the graphical solution of any series/parallel ventilation network. The results are the same, and the approach is logically consistent and less confusing.

Jan 1, 1999

By Greg Adel, Darren Thornton, Julius Krutschnitt, Toni Kojovic, J. Mark Richardson, Bryan Smith

Mine-to-Mill® optimization is a total systems approach to the reduction of energy and cost in mining and mineral processing operations. Developed at the Julius Krutschnitt Mineral Research Centre in Queensland, Australia, it attempts to minimize energy consumption through the optimization of all steps in the size reduction process. The approach involves sampling and modeling of blasting and processing, followed by computer simulation to optimize the operation and develop alternatives. The most promising alternatives are implemented, and sampling is conducted to quantify energy savings. In the current DOE-sponsored research project, the primary objective is to adapt the Mine-to-Mill® technology to the aggregates industry. The project is being carried out at two quarries operated by Luck Stone of Richmond, Virginia. This paper presents work conducted at the Bealeton quarry.

Jan 1, 2005

By Meliton M. Garcia, Satya Harpalani

The volume of gases produced in major and trace amounts as a result of detonation of explosives in an underground mine was determined. The volumes of major gases (CO, CO2, NO and N02) were measured immediately following detonation, during the mucking operation, and following the removal of muck. Tests to identify and quantify the gases produced in trace amounts were performed following the detonation only. The composition of the gases produced varied significantly depending on the composition of the explosive/blasting agent. An average of 95% of the gases produced were found in the test chamber immediately following the detonation, while 2% was found in the chamber following the removal of the muck. Several compounds were identified in trace amounts. Of particular interest was the detection of benzene, toluene, butenes, ethyl benzene and naphthalene since exposure to some of these compounds, even in trace amounts, could present a serious health hazard.

Jan 1, 1987

By Robert E. McIvor

The “Functional Performance Equation for Ball Milling” was first presented in 1988. It now has been used successfully in more than a dozen mineral processing plants. This powerful, yet simple tool provides a new level of understanding of closed circuit grinding. It shows how grinding circuit efficiency is in reality comprised of two distinct efficiencies. It demonstrates how circuit production rate is related, collectively, to these two efficiencies, mill energy input, and the grindability of the ore. It links circuit performance to design and operating variables that can be manipulated, and creates an effective strategy for making plant improvements. This paper covers the derivation and industrial validation of this equation. As part of an engineering and management system that also incorporates suitable metrics and process control, other operators can now use this tool to make improvements and to manage the performance of their grinding operations with clarity and confidence.

Jan 1, 2005

By N. Edmonson

During the last 30 years, a dramatic increase in the supply of byproduct sulfur substantially reduced the share of the market held by Frasch-mined (non-by-product) sulfur in North America. Even though Canadian sulfur production is not discretionary, the geographic remoteness from the large US markets and the high transportation costs associated with delivering sulfur to those markets has meant that Canadian producers act like discretionary producers in many important ways. They have effectively replaced the US Frasch producers as the cost-marginal sulfur source to large US markets. Implications of this change in market structure include more volatile sulfur prices and longer sulfur price recessions.

Jan 1, 1997

By R. I. Pennington, J. L. Vanderbeek

Investigations have been conducted at Chino Mines Co. into the effect that SAG mill recycle material (critical size) exerts on SAG mill throughput and specific energy requirements. Tests were conducted on laboratory, pilot, and plant scales to evaluate the merits of alternative treatment options. Removing critical size material from the SAG mill circuit has been shown to improve new feed rates by 84% with a reduction in specific energy (kWh./t) of 88%. Test results obtained to date are presented.

Jan 1, 1987

By D. T. Kinard, A. A. Schweizer

An operational 9 meter (30-foot) high gold heap leach pile was investigated by excavating test pits up to 6 meters (20 feet) deep, obtaining bulk and relatively undisturbed thin wall drive samples, and observing the ore distribution patterns exposed in the test pit walls. The clayey ore is crushed, agglomerated with lime and cement, and deposited on the leach pads using a radial stacker. Laboratory tests performed included moisture-density, gradation, compaction, Atterberg limits, permeability (constant and falling head), and triaxial strength tests. Discussion is presented on the effects of agglomeration on the permeability and strength characteristics of the in-place ore. Also discussed is the effect of deposition of the ore using the radial stacker.

Jan 1, 1987

If a fire occurs outby an underground coal mine section, the immediate safe evacuation of miners from the working section should always take precedence. Unfortunately, in many cases, the dedicated escapeways (escape routes) for the evacuation of the miners become contaminated by the byproducts of fire from the adjacent entries. The purpose of this paper is to present the ventilation-control process that would keep the escapeway free from contaminants and, thus, available for travel. A few scenarios of mine fires in longwall development panels are analyzed and discussed. To perform these studies, a mine fire simulator (MFS) was used. This (MFS) provides a dynamic representation of the fire's progress (in real time) and gives a color-graphic visualization of the spread of oxygen, combustion products and temperature of the gases throughout the ventilation system. Also presented and discussed are ways in which the MFS can be used as a training and teaching tool for miners and, particularly, for ventilation and safety specialists.

Jan 1, 1997

By Lars Lövgren, Jörgen Jönsson

Heavy metals may be retained within deposits of sulfide minerals under oxidation and in the nearest recipients of drainage water by sorption to secondary iron precipitates. The extent of sorption is strongly influenced by solution pH and presence of complexing ligands, such as sulfate and natural organic acids. Desorption of metals and organidinorganic anions to recent secondary Fe precipitates, collected at the Kristineberg mine, Sweden, has been investigated under different geochemical conditions. Elemental composition and structural characterization (X-ray powder diffraction) indicate presence of schwertmannite. While metals such as Ni and Pb were fractionally desorbed from the precipitates under acidic conditions, oxyanions, e.g. arsenatdarsenite and sulfate were desorbed preferably under alkaline conditions. In a separate study the adsorption of NOM onto synthetic goethite was investigated. NOM adsorption showed a strong pH dependence, 95% was adsorbed at pH 3 and 40 % was adsorbed at pH 9. Addition of 2 mM of sulfate desorbed about 10 % of the adsorbed NOM.

Jan 1, 2000

By Ian Longson, Darron W. Dixon

This paper describes the results of an investigation into the application of a statistical method for the prediction of general air-body methane concentration in longwall coal districts. An important and necessary part of the research was the acquisition of representative monitored mine environmental and coal production data. The monitored data was used to build time series models of general air body methane concentration, air velocity, barometric pressure, coal production and methane drainage variables of differing timescales according to the Box-Jenkins method of time series analysis. The univariate models were used to identify causal relationships between methane concentration and its explanatory variables. Coal production was found to be the dominant variable in the determination of the quantity of methane emitted and where appropriate, multivariate time series models were built in which expressions for methane concentration in terms of coal production were obtained. Finally, forecasts of methane concentration values were generated from the multivariate models to determine their forecasting capabilities.

Jan 1, 1993

By M. J. McPherson, P. Mousset-Jones, G. Danko, I. M. Konduri, F. Calizaya

The flow of air through a bare rock, underground airway is affected by the size and frequency of the micro- and macro-asperities of the rough surface. The focus of this study is to characterize this roughness using the coefficient of friction, the friction factor and the fractal dimension. The rough surfaces were identified by two sets of 177 and 78 transverse profiles measured by a laser profiler along the length of an underground airway at the Sunshine Mine, Idaho. Based on the measurements, the friction factor was estimated from Atkinson's equation and the coefficient of friction from the Moody diagram, and power series and variography were used for computing a fractal dimension for the airway surface. Significant conclusions are reached relating the effect of error in the measurement of cross-sectional and rubbing surface areas of a drift, on the estimated friction factor for the airway. The potential role of the fractal dimension as an alternative to the friction factor for characterizing the roughness of a mine airway is discussed.

Jan 1, 1993

By J. Bartrum, A. Bowler, G. Butcher

The purpose of this paper is to outline the design, specification, and operation of the 8.5-m- diam (28-ft-diam) SAG mill commissioned at Kidston Gold Mines during January 1985. Amenability of Kidston ore to SAG milling, coupled with substantial cost advantages, led to the specification of this mill, equipped with variable speed drive to overcome the large variation in ore hardness. Operation of the mill is effected via a number of automatic control loops. Problems experienced with automatic control plus other electrical and mechanical failures have led to design changes and the formulation of future operating strategies.

Jan 1, 1987

By J. Hanna, I. Anazia

Selective fatty acid flotation of carbonate gangue from sedimentary apatites was achieved under acidic pHs without a specific apatite depressant and without conditioning the pulp with the collector. Concentrates (35% to 38% P2O5, 0.8% to 1% MgO) with high recoveries (80% to 85%) were produced from Indian and Chinese dolomitic ores. The calcareous and/or dolomitic-siliceous phosphate ores of South Florida and Utah required two flotation stages: one for carbonate removal, as mentioned above, and the other for phosphate recovery from siliceous gangue. Preliminary tests on the South Florida ore gave concentrates analyzing 29% P2O5 and 0.8% MgO, with a P2O5 recovery of 76%. A concentrate obtained from the western US phosphate ore from Utah assayed 30% P2O5 and about 1% MgO, with a P2O5 recovery of 89%.

Jan 1, 1988

By R. Y. Wan

Newmont Gold has advantageously used the capabilities of mineral oxidizing bacteria to develop a process for the pretreatment of low-grade sulfidic and carbonaceous-sulfidic refractory gold ores. The biooxidation process results in the oxidation of the sulfidic minerals with increased exposure of gold for subsequent gold recovery. The biooxidized carbonaceous-sulfidic ores cannot be heap leached with cyanide because of the preg-robbing characteristics of the carbonaceous matter in the ores. Therefore, an alternative heapleach process using ammonium thiosulfate was developed to extract gold from these preg-robbing bioaxidized ores. The ammonium thiosulfate leach process was successfully applied in both laboratory and pilot plant tests. Satisfactory test results were achieved, encouraging the continuation of process development.

Jan 1, 1997

By Jeffrey Anderson, Cindi Byrns, Andy Davis

A closure plan was developed for the Intera Pond Facility, a former acid leaching collection pond at the BHP Robinson Mining Operations. To properly close the Intera Pond Facility, an engineering plan that was both technical and cost effective was developed. A primary objective of this closure project was to demonstrate to State regulators that following the proposed plan would minimize further degradation of water resources. Field data demonstrated natural attenuation of metal enriched solutes via carbonate reactions. Prospective fate and transport modeling indicated that it would not continue to degrade waters of the State.

Jan 1, 2000

By E. L. Smyth, A. Button

The apparent absence of significant Tertiary auriferous palaeoplacers in the Yilgarn Block of Western Australia can be explained by the dissolution of the placer gold into the highly saline, acid, oxidising ground waters which currently occur in upper portions of the palaeochannels proximal to the gold sources. The dissolved gold has then been redeposited in redox fronts further downstream. The placer gold is preserved in more distal portions where the ground waters are reducing. Exploration for these placers can be effective using the gravity contrasts that exist between the Tertiary sediments and the Archaean bedrock and SIROTEM which can detect the highest salinity zones which occur in the deepest parts of the channels. Final assessment of the gold content of the sediments must be determined by drilling.

Jan 1, 1989