Search Documents

By M. Wrobel, J. Hammerschmidt, M. Runkel

Fluid-bed technology is a key pyrometallurgical step for processing a vast number of ores and concentrates. Over the past 50 years, considerable research and development efforts have been made by Metso Outotec to expand the application window of this technology. This paper illustrates different processing routes where fluid-bed technology plays an important role in the production of the copper. The fluid-bed processes utilized are partial, sulfate-producing, and dead roasting. The focus of this paper considers the advantages of the dead-roasting process. This “zero waste” process can provide copper oxides, steam, electrical power, and sulfuric acid for new and existing solvent extraction–electrowinning plants. In a case where an operation is running out of oxidic ores and concentrates, fluid-bed roasting can be applied to close this gap and provide the required copper oxides in a sustainable way.

Jan 1, 2023

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental sampling error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centred on the sampling constant K and the exponent, alpha (a) of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis method and the heterogeneity test method purport to provide such constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine, and Lily mine. Two of these mines (Mponeng and Kloof) are typical Witwatersrand-type gold mines, and the third is an Archaean-type shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appear to be too small and do not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2010

By N. Sutcliffe

Refractories and slags play a vital role in the production of stainless steel. They are in intimate contact with the steel at temperature, and chemical reactions between the three can and do occur. These interactions can be beneficial, in the case of active tundish and ladle slags, and negative in the case of refractory erosion and slag entrapment. This paper presents the results of both plant trials and laboratory investigations of steel/refractory and slag/refractory interactions. The interaction mechanisms observed are described leading to selection criteria for new refractory products. Keywords: slags, steels, refractories, reaction mechanisms.

Jan 1, 2004

By M. Grodner

Underground excavations exhibit different hangingwall conditions in response to varying geotechnical and mining situations. These differences need to be quantified so as to accurately determine the effectiveness of the mining and/or support strategies. A useful tool for the quantification of these differences is hangingwall profiling. Two methods of hangingwall profile measurement are described?termed irregular and periodic methods. Several data analysis techniques are reviewed for these methods and the suitable ones are discussed in detail. For irregular data the suitable techniques are the determination of the length, the average of the profile and the average absolute deviation from the mean of the profile. All of these techniques as well as determination of the moving average of the height and examination of the spectral image of the profile can be successfully applied to regular data. The effect of preconditioning on the hangingwall is discussed as an example and it is quantitatively shown that it results in improvements of conditions. The techniques described allow the engineer to quantitatively identify the appropriate support type or mining strategy and thus represent a valuable decision-making tool. It is suggested that these techniques should be employed on a routine basis by the rock engineers on the mines as part of their geotechnical classification, as well as support manufacturers to quantify the effectiveness of various support types.

Jan 1, 2000

By B. G. Tarasov

This paper proposes the further development of a recently identified shear rupture mechanism (fan mechanism) that elucidates a paradoxical feature of hard rocks ? the possibility of shear rupture propagation through a highly confined intact rock mass at shear stresses that can be significantly less than frictional strength. In the fan mechanism, failure is associated with consecutive creation of small slabs (known as ?domino blocks?) from the intact rock in the rupture tip, driven by a fan-shaped domino structure representing the rupture head. The fan head combines such unique features as extremely low shear resistance, self-sustaining stress intensification, and self-unbalancing conditions. Consequently, the failure process caused by the mechanism is inevitably spontaneous and violent. Physical and mathematical models explain unique and paradoxical features of the mechanism, which can be generated in primary ruptures and segmented faults. The fan mechanism provides a novel point of view for understanding the nature of spontaneous failure processes, including shear rupture rockbursts. The process explains, in particular, features of shear rupture rockbursts such as activation at great depths, generation of new shear ruptures in intact rock mass, nucleation of hypocentres at significant distances from the excavation, shear rupture development at low shear stresses, and abnormal rupture violence.

Jan 1, 2014

By P. Bracher

Most efforts to mechanize low seam (narrow reef) mining of platinum ore are presently based on board-and-pillar methods with1.6?1.8 m in reef excavation. This paper attempts to substantiate the benefits of low profile mining: primarily improved head grade with resulting reduced tailings losses. Board-and-pillar equipment supplied by DBT, facilitating1.1?1.2m mining height has been in operation in an Anglo Platinum mine since September 2001. Major aspects of the equipment, battery scoops (LHDs) and rotary bolting rigs, are described and presently achieved results reported. The medium term industry goal is rock breaking without the use of explosives. An outline of present DBT developments is presented.

Jan 1, 2003

By J. M. Ortiz

Grade control and short-term planning are usually based on the samples obtained from blastholes. These samples may carry a large sampling and sample preparation error. At El Tesoro copper mine in northern Chile, an advance drilling grid is used for short-term planning and grade control. These drill holes are sampled well in advance, and a short-term model that incorporates several variables and sophisticated estimation methods can be prepared for decisionmaking. An additional advantage of the advance drilling samples is that reverse circulation can be used instead of conventional down-the-hole equipment, and a very careful sampling and sample preparation process can be implemented, reducing the total sampling error. Advance drilling can be performed on a wider grid than blasthole drilling, hence the decision about the grid requires assessing the economic benefit of different sampling grids. Furthermore, this process allows the cost of poor sampling and the effect of different estimation procedures to be quantified. We demonstrate the optimization of the drilling grid for short-term planning and grade control at El Tesoro mine by means of the economic evaluation of the performance of different drilling grids, with different drilling techniques (which differ in the sampling error). The methodology is based on creating dense (exhaustive) geostatistical simulations of the grade distribution over a volume defined for a production period in respect of the geological model, and assuming each simulation as the true grade distribution. Then, samples are obtained from the exhaustive simulations at a spacing similar to the advance grid to be evaluated, and a sampling error is added. The short-term estimation procedures used on the mine are applied to determine the destination of each block and the profit obtained. This profit can be compared with the maximum profit (unachievable) and with the profit under different sampling errors and grids. The results show that the current 8 x 8 m drilling grid is appropriate and by reducing the sampling error, misclassification is also reduced, leading to an increase in profit of about US$ 5 million in 4 years.

Jan 1, 2012

By van der Merwem J. N.

"Coal pillars are prone to scaling over time, and are progressively reduced in size and consequently subjected to increased load and reduced strength. The effective factor of safety therefore reduces. Databases of failed and stable pillars cannot, therefore, be regarded as definitive.More than a decade has passed since the first attempt to predict the lifespan of pillars. This paper presents a review based on the new database and pillar strength equations. The methodology for the analysis is based on the fact that pillars scale. The ultimate safety factor (defined as the ratio between strength and load at the time of failure) is derived, followed by an estimate of the rate of pillar scaling, which results in an estimate of the expected time of failure.It is suggested that the predicted lifespan should not be used as an absolute indicator of expected pillar life, but rather as an index – the pillar life index (PLI) – to complement the safety factor and related probability of failure when evaluating pillar stability. A pillar with a predicted lifespan of less than 500 years would be regarded as being in danger of imminent collapse, while a lifespan of at least 1 000 years should be required for long-term purposes.The differences between this analysis and that published in 2003 constitute a strong case for regular reviews of all the empirically based stability indicators, namely the safety factor, probability of failure, and the PLI. Reviews at 10 year intervals appear to be required.The constants in the proposed method are valid only for the Witbank No. 1, 2 and 4 seams and the Highveld No. 2 and 4 seams.IntroductionIt is well known that over time, coal pillars are prone to scaling, and thus are progressively reduced in size and consequently subjected to increased load and reduced strength. The effective factor of safety therefore reduces and it is quite possible for failure to occur after a long time interval. In fact, scrutiny of the database of failed pillars indicates that failure occurred after periods ranging from 2 to 49 years, and not immediately after mining.The factor of safety for pillars at the time of failure is not the same as that immediately after mining. The concept of the safety factor is based on the pillar strength obtained by statistical analysis of pillar dimensions immediately, or within a month after mining, when the surveys are conducted. Strictly speaking, the safety factor as commonly used is valid only immediately after mining, and it continues to reduce thereafter. The ideal situation would be to base analyses of pillar strength on pillar dimensions at the time of failure, but that is simply not possible because the real dimensions cannot be measured at that time."

Jan 1, 2016

The development of 3D multi-parametric models facilitate the provision of resource information well in advance of the mining face. Using the model, one can evaluate mining areas not only for grade and tonnage predictions but also for predictions of rock mass quality. Blast design and milling requirements can be derived from the rock mass quality predictions. This information can be used for overall mine planning and evaluation, costing, production optimization and slope design. This allows the full range of mining activities and costs to be interconnected, thereby lowering costs and improving efficiencies through the application of the multi-parametric model. Feasibility studies for new projects require an expected budget expenditure estimate to within 5% of actual costs. This level of accuracy is expected by mining companies and investors but cannot be achieved without a sound knowledge of the rock mass variability. By developing a 3D multi-parametric model as part of the feasibility study and using the same geological model exploration boreholes, a significantly better understanding of the rock mass conditions can be obtained. This rock mass information can be used for equipment selection, economic pit layouts, processing plant design, underground mining layouts and support requirements, to name but a few design parameters that depend on rock mass conditions. The initiative at Anglo Platinums, Potgietersrust Platinum Ltd.?s (PPRust) operation, has delivered significant results showing improvements across the mine to mill value chain. These include increased loading rates, reduced electricity and crushing consumables, as well as higher plant throughput. The ore reserve model has gained international acceptance as an invaluable tool for a mining operation. Certainly most financial organizations will not invest in a mining project that does not have an ore reserve model. There is the potential for multi-parametric models to be recognized as vital tools in the mining process, as is the case with ore reserve models.

Jan 1, 2007

By V. Coetzee

In 1992, a paper was compiled highlighting a common-sense approach to electric smelting at Impala Platinum. Since then, the smelter complex has undergone considerable changes. Mineral economics, UG2 exploitation, and changing environmental legislation have enforced numerous process upgrades, yet a common-sense approach has always been adopted. This document details the major changes in the smelter complex at Mineral Processes (Minpro) over the past 15 years, and provides the rationale for the changes. Keywords: Pyrometallurgy, furnace, PGM, platinum, nickel, copper, electric smelting, six-in-line, Peirce-Smith, Impala Platinum.

Jan 1, 2006

By P. F. Ledwaba

"Artisanal and small-scale mining (ASM) in South Africa received official recognition after the change in government in 1994.The Reconstruction and Development Programme (RDP) recognized the sector as a vehicle for social and economic development for historically disadvantaged South Africans (HDSAs) who had previously been excluded from participating in the mainstream economy. Having recognized the ASM sector, government introduced several interventions and support structures to foster the development of ASM, to encourage participation of HDSAs, and to address challenges facing the sector. The objective of this paper is to assess the progress made, with particular regard to challenges in the sector. The paper focuses on the policy requirements that were deemed important for the growth of the ASM sector by the White Paper on Minerals and Mining Policy (1998). These can be collated into five categories: access to mineral rights, access to finance, access to markets, technology and skills, and institutional support. The paper provides a review of the support interventions, their intended roles and impact on the sector, and identifies existing gaps and possible ways of dealing with the challenges. There is a need for research to assess the real impact of these past and existing interventions on the ASM sector to draw lessons for future development.IntroductionThe significant rise in artisanal and smallscale mining (ASM) activities worldwide has led to many countries recognizing the sector. ASM takes place in approximately 80 countries (World Bank, 2013). It is estimated that the sector employs between 20 and 30 million people around the world (Buxton, 2013). This compares to between 3 and 3.7 million in 1999 (International Labour Organization, 1999). ASM activities are widespread, occurring mostly in developing countries in Africa, Asia, Oceania, and Central and South America (World Bank, 2013). There has been a significant increase in the number of people participating both directly and indirectly in the sector and this is expected to continue given the socio-economic realities of most developing countries. High levels of poverty and unemployment and growing inequality continue to be largest problems facing the majority of developing countries today. The ASM sector plays an important role as a source of livelihoods, particularly for those residing in rural areas with limited economic opportunities. In the majority of countries, the recognition of the ASM sector was driven by its increasing contribution to socio-economic development through job creation, poverty alleviation, and rural development. In response, a number of intervention strategies were introduced in support of the sector to address its negative impacts and to increase its potential benefits."

Jan 1, 2017

This is a sampling of the papers presented at the conference, the proceedings can be bought from the SAIMM The technique reported here involves measuring the air pressures generated within sealed boreholes located behind blasts. Results from twelve free face blasts in competent rock environments a represented. There were no instances of high pressure gas penetration, even at distances corresponding to less than one blast burden. Rapidly generated underpressures were measured in most holes, with the magnitudes of the peak pressures decreasing with distance behind the blasts. It has been proposed that the under pressures are the result of new volume created due to crack formation and overall rock mass dilation. The experimental evidence is consistent with this, including a correspondence of the onset times of the peak underpressures with the nominal firing times of the nearest blastholes. New post-blast cracks were observed when using borehole video cameras in the monitoring holes. A calculation of new volume produced within the monitoring holes is proposed as an indicator of damage. While the data exhibit considerable scatter, there is a power function dependence on scaled distance, which resembles that of typical vibration data. The data also lie within the normally quoted vibration regimes for rock damage and are consistent with measured extents of damage. It is concluded that this technique may provide an inexpensive and practical comparative measure of near-field rock damage due to blasting. It is further concluded that gas penetration is not a common phenomenon. Damage appears to be mainly attributable to the nearest blastholes and the control of charge mass in perimeter blastholes is emphasized for damage minimization.

Jan 1, 2000

By Peter Townsend, Sergei Diachenko, Allan Moss

The Palabora Mining Company has successfully extended the life of its operation by developing a 30,000tpd block cave underground mine below the now closed open pit. The process of transitioning from surface to underground mining has been technically, operationally and managerially challenging. This has been due to a number of factors; in particular, the development of a block cave in a very competent rock mass. The competence of the rock mass is clearly demonstrated in the open pit that preceded the block cave, one of the steepest deep open pit excavations in the world. With cave breakthrough, however, the pit was ?instantaneously? deepened by 400m causing a major failure of the northwest wall involving close to 100Mt of waste material.

Jan 1, 2006

By M. F. Wells

The method used to salvage South Deep?s Main Shaft after it was flooded by an inrush of water at about 450 m below collar on 1 May1996 is described. The individual techniques employed in the salvage were all proven technology, but the combination in which they were applied is considered to be novel. The operation involved the following activities in order of occurrence. ?the dewatering of the shaft with submersible pumps ?the placement of a French drain on the shaft bottom muck pile ?the positioning of large diameter heavy walled draft tubes, and smaller tightening up, grout intrusion and reverse flow pipes ?the casting and curing of a structural concrete plug; the capping of the draft tubes; the intrusion of several thousand tons of cement grout into the aquifer by pressure induced reverse flow ?the sealing of the aquifer ?extensive probe drilling and sealing of the zone around the inrush point with cement and other specialized grouts ?the mining out of the plug and the re-establishment of normal sinking routines.

Jan 1, 1999

By J. N. Van der Merwe

In the process of pillar extraction, pillars are seldom if ever extracted completely. The pillar remnants, or snooks, play an important role in the extraction process. At the working face, they need to be stable to provide a measure of support in the immediate area. Further back, they have to fail in a controlled manner to prevent undue load build-up on the pillars that have not yet been extracted. The stability condition at the working area is the result of interaction between the stability of the pillar and that of the roof rock. It is shown that the primary mode of roof layer failure is by bending induced tension. Direct tension can be excluded in most practical conditions, and only in exceptional cases will the first failure be in shear mode. Panel spans required to cause the first goaf to be formed, predicted using analytical considerations, are of the same order as has been observed in practice. Once the first goaf has formed, the horizontal stress is reduced and failure will occur at more frequent intervals. It is shown that bending induced tension is the most likely mode of failure in an unjointed roof layer. In roof layers with a high frequency of weak or uncemented jointing, failure can be expected to occur at spans equal to the joint spacing. In this context, failure will occur at the smallest of the spans required to induce tensile roof failure and the joint spacing. A fundamental procedure to evaluate the likely roof layer failure in a stacked beam system is developed. This can to be used to estimate the loading condition on snooks. It is shown that snooks assist in stabilizing the immediate roof beam. The sizes and positions of the snooks relative to the position of the next pillar to be stooped, control the magnitude of the contribution to stability. The further the snook is from the next pillar, and the larger it is, the greater the contribution to the stability of the immediate roof. Under the condition of loading by the immediate, continuous roof beam, the position and size of a single snook controls the load acting on it. The closer it is to the nearest solid, provided that the roof overhang extends beyond the snook, the greater the load on it. However, once the immediate roof beam fails, the loading conditions change. The snook is then loaded by the tributary area load. A procedure is developed to assess the condition of snooks for different situations. Using the fundamental considerations developed in this paper, snooks can be designed to be stable during the active mining phase in their immediate vicinity, but to fail once the next line of pillars has been extracted.

Jan 1, 2005

By B. Samanta

LHD (load haul dumper) is now used as a loading machine for intermediate mechanization in underground coal mining. For survival in the intense competition in the global business environment in recent years it is essential that LHD machine should be reliable and maintained effectively and efficiently. This paper seeks to study the reliability, availability and maintainability (RAM)of an LHD machine with failure and repair data by Markov modelling. The constraints and reasons for machine unavailability are outlined. The reliability and maintainability of an LHD and its subsystems are evaluated. Possible modification or design alternatives are highlighted. Reliability and maintainability of an LHD system are disappointing. There is room to take decisions on optimal maintenance planning and machine improvement from this analysis. Keywords: reliability, availability, maintainability, Markov model, LHD

Jan 1, 2004

The acoustic signals emitted from a laboratory-scale ball mill were used for the estimation of the comminution of two complex sulphide ores, viz. Merensky and UG2 ores from the Bushveld Igneous Complex in South Africa. The digital acoustic signals were transformed to power spectral densities that could be related to particle size distributions (-75 µm to 4000 µm) in the mill by use of continuum regression. This approach is more general than principal component regression methods or Kalman filtering used previously and resulted in significantly more accurate calibration in the case of the Merensky ore, where approximately 93.4% of the variance in the particle size distributions could be explained. With fewer data available, the variance in the particle size distributions in the UG2ore could be explained less accurately (82.4%), but still satisfactorily. In addition, smaller particle sizes (less than 300 µm) could be modelled more accurately in the case of the UG2 ore.

Jan 1, 2000

By John V. Simmons, Peter J. Simpson

Excavated slopes in open pit coal mines are designed to be as steep as possible consistent with stability and safety requirements. Slope failures occur for many reasons, including oversteepening. This paper is concerned with slope design and excavation experience in the Bowen Basin coalfields of central Queensland (Figure 1), [ ]

Jan 1, 2006

By W. Stumpf

Mill log analyses and complementary hot deformation studies were carried out on the as-cast structure and on a hot rolled structure of the same low carbon steel (SAE 1006) that had been processed according to the direct or hot charge route in a compact strip plant. The main softening mechanisms during hot rolling were found to be complete dynamic recrystallization during each pass above about 1000°C for the as-cast structure with an austenite grain size of 277µm and, secondly, incomplete static recrystallization after each pass with a finer austenite grain size of about 26 µm and tested below 1000°C. A two-stage hot working mechanism has also been found by others on a similar steel also processed by the hot charge route and this may appear to be a characteristic of this type of material. Constitutive constants determined from hot working studies were combined with other constants from the literature and incorporated into a grain size development model that correctly predicts the final ferrite grain size in the hot rolled strip steel. The predicted incomplete static recrystallization during the last three finishing passes in the plant appears to result in some retained strain in the hot rolled austenite as it transforms to ferrite on the run-out table. Analyses with the model predict relatively little sensitivity of the final ferrite grain size to process and product variables such as temperature and strain per pass for the last three passes and also the starting austenite grain size in the slab. Keywords: Low carbon steel, hot rolling of strip steel, rolling mill log analyses, austenite grain size, ferrite grain size, grain size modelling.

Jan 1, 2003

Stope support systems, typically consisting of props and packs, are used extensively in the gold and platinum mining industry to stabilize the rock mass in the excavation vicinity and to reduce the hazard associated with rockfalls and rockbursts. The design of stope support systems was historically based predominantly on past experience and practices, and cost considerations. The recent development of a new and improved support design methodology, has led to the potential for significant increases in worker safety and support cost savings. This paper reviews some of the fundamental rock mass and support criteria that form the basis of the improved support design methodology. The considered design criteria are the height of potential fall; quasi-static stope closure rates; dynamic stope closure rates; compressive hangingwall stresses; discontinuity spacing, orientation and interface properties; effect of support length (stoping width); effect of compression rate; consistency of support performance; a real coverage; support spacing; and zone of support influence. The proposed support design methodology combines both the zone of influence and key block stability theories, resulting in optimized support systems for rockfall and rockburst conditions. The site-specific methodology consists of two stages: (i) a tributary area analysis, and (ii) a zone of support influence and a stability analysis, considering hangingwall failure due to buckling, shear and block rotation, which gives maximum safe spacing of individual support units. The methodology is suitable for designing support systems for both blocky hangingwalls and hangingwalls fragmented by face-parallel extension and shear fractures.

Jan 1, 2001