Search Documents

By P. Turcotte, E. Karampinos, F. Mercier-Langevin

In some underground hard-rock mines, squeezing compressive ground conditions are influenced by the presence of rock foliation and high stress. In these cases, the orientation of the foliation with respect to the drift direction has a considerable impact on the magnitude of the resulting deformation. Irrespective of the reinforcement and support strategy, keeping drives developed sub-parallel to the rock foliation operational is difficult, and often requires excessive rehabilitation during the lifetime of the excavation. This study uses field observations and convergence measurements at the LaRonde and Lapa mines of Agnico Eagle Mines Ltd to provide guidelines of the anticipated squeezing levels at these operations.

Jan 1, 2015

By B. P. Watson, T. J. Maphosa, D. P. Roberts, L. J. Gardner

The results of FLAC3D modelling on chromitite Upper Group 2 Reef pillars from the Bushveld Complex of South Africa are described. The model input parameters were determined from laboratory triaxial tests with post-failure measurements. These geomechanical tests were performed on rock materials within the pillars and the immediate pillar foundations. In the models, postfailure behaviour was simulated using the concept of cohesion softening. Models were built to determine the strength and behaviour of pillars with a width-to-height ratio of approximately two. The original research aimed to find a suitable depth below the surface where Impala Platinum Ltd could safely introduce crush pillars; however, the paper only describes the model results: the ideal depth of the crush pillar introduction is not discussed. The results of the modelling are compared with the PlatMine formula for peak pillar strength and with an underground instrumented pillar located elsewhere on the same reef. Some insight into the effects of grid size on strength is also provided. Further underground measurements are recommended to verify the model results

Sep 9, 2024

By C. Scheffer

This paper describes a model that can simulate the behaviour of a pneumatic intensifier that is generally referred to as an ?air pump? (AP). The AP is used in many South African underground mines, and utilizes compressed air with pressures between 0.3?0.6 MPa to pump water up to pressures of 12?18 MPa. The high pressure water is used in numerous underground mines to pressurize props and roof bolts that act as safety and roof support devices. The simulation model reproduces the intensifier's operation under various conditions and therefore can be used to investigate the AP's sensitivity towards environmental conditions, design parameters (such as spring stiffness, plunger diameter, nozzle diameter etc.) and operating conditions. Model validation by comparison with laboratory experiments showed good correlation. The model can subsequently be used to investigate design changes aimed at improving the AP's performance and reliability over a wider range of operating conditions.

Jan 1, 2005

By H. Askari-Nasab, S. Upadhyay, A. Moradi-Afrapoli

Material handling in surface mines accounts for around 50% of the operational cost. Optimum truck dispatching plays a critical role in the reduction of this operational cost in truck and shovel surface mines. Researchers in this field have presented several mathematical models to solve the truck dispatching problem optimally. However, a critical survey of the literature has shown that three significant drawbacks exist in the available truck dispatching models. The published models underestimate the importance of the interaction between truck fleet, shovel fleet, and the processing plants. They also disregard goals set by strategic-level plans. Moreover, none of the available models account for the uncertainty associated with the input parameters. In this paper we present a new truck dispatching model that covers all of these drawbacks, using a fuzzy linear programming method. The performance of the developed model was evaluated through implementatin in an active surface mining operation. The results show a significant improvement in production and fleet utilization.

Sep 1, 2021

By M. Smit, N. C. J. Dempers, S. Lunkov, C. Saguru, J. Nel

A common method for the recovery of copper is by heap leaching, solvent extraction, and electrowinning. During solvent extraction, the solution is continuously recycled, and it is necessary to remove impurities that build up in the raffinate. For the process investigated in this study, the main impurities include Fe, Co, As, and Zn. Recovery of these impurities can provide economic benefits while adhering to legal and environmental constraints. Such impurities are often removed by precipitation utilizing a neutralizing agent, such as limestone or lime, but it is also possible to remove the impurities by sulfide precipitation. Sodium hydrosulfide (NaHS) is used to selectively precipitate copper, arsenic, and zinc from a solvent-extraction raffinate stream. The resulting sulfide precipitate is bagged and sent to a roaster for further treatment. The design of the sulfide precipitation was investigated to optimize the processing conditions (including temperature, pressure, and residence time), the materials of construction, and the toxicity and explosive nature of the hydrogen sulfide gas produced

Jan 1, 2023

By D. B. Rebuli

Seismic networks in deep gold mines of South Africa are often planar owing to the tabular geometry of the orebody and, therefore, the mining infrastructure. Consequently, seismic event locations are poorly constrained in the direction perpendicular to the reef plane, and symmetrical locations above and below the reef plane may fit the observed data equally well. This problem may be resolved in situations where the strata above and below the reef plane have significantly different seismic velocities, which is the case for the Ventersdorp Contact Reef at Kusasalethu mine (previously Elandskraal, the amalgamation of Deelkraal and Elandsrand). A location method using a layered location model that takes into account the velocity contrast between the layers was tested. Observed direct- and head-waves were used to determine the velocity bounds of the P-wave velocities in the two-layer model. The data-set was also used to find the best P- and S-wave velocities for the two layers by grid searching over a range of velocities and minimizing the sum of the travel-time residuals. The results from the grid search and those from the calibration of velocities using direct- and head-waves give similar P-wave velocities for each of the two layers. A second set of seismic events was then relocated with this layered model and locations closer to reef were found. This simple layered location method goes some way to reduce the reefperpendicular location errors for Kusasalethu mine in particular. Keywords mine seismology, velocity model, location methods.

Jun 1, 2013

By D. F. Malan, P. J. Le Roux

Almost no work has been published on the strength of pillars in mines exploiting the LG6/LG6A chromitite bands in the Western Bushveld Complex. The strength of these pillars is unknown, and the hard rock industry still uses the Hedley and Grant formula. Numerical modelling, using inelastic constitutive models, may be of some value in estimating the pillar strength, but this approach is difficult and prone to errors as many assumptions are made. This paper explores the alternative approach of the back-analysis of actual LG6/LG6A mining layouts, using displacement discontinuity codes to simulate the average pillar stresses on a mine-wide scale. From this, and underground observations, a ‘minimum’ pillar strength (K-value in the pillar strength formula) can be estimated. The codes TEXAN and Map3D are both used in the paper to simulate the actual pillar shapes and sizes in an LG6/LG6A mine. The results are encouraging as the two codes produced similar APS values for a complex pillar geometry. An estimated K-value of 77 MPa was determined for the LG6/LG6A pillars in this particular area. This is more or less similar to earlier work done for the UG2 chromitite seam, but higher than the K-value of 39 MPa for a linear formula obtained by other workers for LG6/LG6A pillars. Caution should therefore be exercised before using this higher value for all areas. The effect of element sizes and explicitly simulating the effect of the surface for shallow pillars is illustrated in the manuscript using both codes. The need for actual pillar observations and an iterative design process, which cycles between modelling and observations, is also emphasized.

Nov 27, 2024

By C. Ringas

Pipelines are used extensively in industry to convey various products. Internal corrosion of pipelines can lead to perforation and leakage of the product. A growing problem, not often accurately recognized, is internal corrosion of pipelines caused by bacteria. Microbiologically-induced corrosion (MIC) refers to corrosion caused by a variety of micro-organisms. This form of corrosion is not widely recognized in many industries, although it is widespread and causes many corrosion problems in pipelines, both internal and external. Sulphate-reducing bacteria (SRB) are responsible for the bulk of the corrosion problems caused by MIC. Corrosion caused by SRB is found extensively in water pipelines conveying raw, potable and waste water, as well as in pipelines conveying slurries. This problem also occurs in pipelines conveying crude oil. This paper describes internal corrosion problems of slurry pipelines caused by bacteria and outlines mitigation methods to improve slurry pipeline integrity, thereby extending the life of such pipeline

Jan 1, 2007

By B. S. Xakalashe, M. Khama, Q. G. Reynolds

Pre-reducing chromite with hydrogen offers significant benefits, including reduced energy consumption in downstream smelting and lower carbon dioxide emissions. To leverage these advantages, it is essential to develop computational models that facilitate the design, optimisation, and control of the process. Full scale models such as 3D computational fluid dynamics models are often used to investigate the multi-scale flow physics in heterogeneous reactors. However, these models impose prohibitive computational expense in the modelling of heterogeneous reacting flow systems. The high computational expense prevents the use of high dimensional systems in real time control and online optimisation of reacting flow systems. In order to facilitate incorporation of predictive models in the heterogenous reacting flow systems control loop, computationally efficient reduced order models are required. Owing to these requirements, a reduced order model for pre-reduction of chromite with hydrogen was developed with the view to rapidly predict the performance indicators for pre-reduction of chromite with hydrogen. The Thiele modulus method was used to develop the reduced order model, and the model results were compared to isothermal pre-reduction experimental results at a range of pre-reduction temperatures from 1200 oC to 1400 oC. The model predicts the degree of reduction, diffusion of gases through the product layer, unreacted core radius of the grain radius, and local and global conversion. The final conversion across all temperatures as predicted by the reduced order model deviate from the experimentally calculated conversion by a maximum relative error of 2.7% while the initial conversions differ significantly, reaching a maximum error of 65%.

Aug 3, 2026

By M. Abdellatif

Keywords: Magnesium, pyrometallurgy, Mintek Samples of crude magnesium produced by the Mintek Thermal Magnesium Process were refined in two stages. The first stage consisted of co-melting of batches of the crude metal and MgCl2-KCl flux (cleaning), followed by stirring at 30 rpm for 30 minutes and settling of the sludge (mixture of molten salt and solid impurities) from the magnesium melt. The operating temperature was 680?730°C. Most of the contained calcium and significant proportions of iron and silicon were transferred into the sludge phase, which left a metal containing, on average, 950 ppm Si, 470 ppm Fe, and 230 ppm Ca. In the second stage, small-scale refining tests were conducted on cleaned samples from the first stage, as well as on crude magnesium. FeCl3 was used as the refining agent. These tests were carried out at 715?760°C with various amounts of the refining agent. The refined metal was suitable for the production of various magnesium alloys, particularly AZ91D.

Jan 1, 2006

By S. L. George

The semi-solid metal casting process results in a unique solidification path. The microstructural features that were identified during the characterization of the as-cast microstructure, were used as evidence of the process history in order to determine the solidification path followed during the evolution of the microstructure. The morphology of the grains was characterized using SEM and the extent and distribution of the elemental segregation within the grain structure was analysed using EDS. Keywords Semi-solid casting, solidification path, segregation.

Jan 1, 2011

By F. M. L. Mulaudzi

Behaviour studies of metal dusting processes and associated filamentous carbon formation were undertaken on Alloys 600, 601, and 800 using a simulated metal dusting environment of 25C0-70H2-5H20 (vol.%) at 650°C. These samples were studied visually and by optical microscopy, scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), transmission electron microscopy with energy-dispersive X-ray spectroscopy (TEM-EDX) and x-ray diffraction (XRD). Visual examination and SEM surface observation showed that Alloy 800 suffered metal dusting attack at an early exposure reaction period. The coke deposit amounts increased significantly with reaction time from 168 hours to 336 hours in Alloys 600, 601, and 800. Alloy 800 showed pitting after 168 hours' exposure, and the degree of pitting increased after 336 hours. XRD showed all these alloys had a common austenitic phase, with Alloy 800 also having ferritic metal particles. Alloy 800 after 168 hours' exposure had a complex phase mixture on the surface, consisting of ferritic Fe and austenitic FeNi phases. For coke deposit, there were also Fe304, Fe3C and graphitic carbon. The existence of Fe, Ni, and Cr metal particles, and also graphitic carbon in coke deposits, was confirmed by EDX analyses.

Jan 1, 2013

By L. Mpolokeng, J. P. Labuschagne, H. Yilmaz

"An investigation into pillar cutting was carried out at a platinum mine on the western limb of the Bushveld Complex. The focus was on crush pillar design and implementation in order to ultimately improve the compliance percentage for pillar cutting. The major findings from the investigation suggest that the pillar cutting problem lies with the implementation of the design rather than the design itself. Observations of the practical issues underground that prevent good pillar cutting were made. After these issues had been identified, recommendations to rectify these problems and a few other issues identified during the investigation were provided. The recommendations are aimed at improving the pillar cutting compliance and reducing the likelihood of pillar bursts or pillar runs, which will ultimately create a safer mining environment. Paper written on project work carried out in partial fulfilment of BSc. Eng. (Mining Engineering)"

Jan 1, 2015

By M. Rafie, M. Rinne, F. Samimi Namin

"SynopsisRock mass classification systems constitute an integral part of empirical underground excavation design. One system that is commonly used to classify rock mass is the Rock Mass Rating, or RMR, system. The RMR system has evolved over time to better reflect the perceived influence of various rock mass factors on excavation stability. While the introduced modifications have enhanced the applicability of this classification system, there are still areas that cause potential ambiguity. The RMR system cannot deal with input data ambiguities, uncertainties, and vagueness. To deal with the uncertainty, a Fuzzy Rock Mass Rating (FRMR) has been developed. This study aims to describe the main concept of the fuzzy approach, which is implemented in the FRMR to classify rock mass. The FRMR considers the uncertainty associated with the input data (uncertain variables) used in rock mass classification. The Gol-e-Gohar (GEG) area 3 iron ore deposits in the south of Iran were chosen as the case study for investigating the applicability of FRMR. The results of this study show that the FRMR software tool can easily be used for rock mass classification, even if uncertain input parameters have been used. FRMR consists of three parts, each of which is suitable for certain conditions.IntroductionNowadays, rock engineering classification systems, which constitute the backbone of the empirical design approach, are widely employed in both civil engineering and mining engineering. Rock mass classifications have recently been quite popular and are being used mostly for the preliminary design and planning purposes of projects. According to Bieniawski (1989), a rock mass classification scheme is intended to classify the rock masses, provide a basis for estimating deformation and strength properties, supply quantitative data for support estimation, and present a platform for communication between the exploration, design, and construction groups."

Jan 1, 2015

By P. Share

As part of JAGUARS (JApanese-German Underground Acoustic emission Research in South Africa), high-resolution tiltmeters were installed during 2007 at Mponeng gold mine, South Africa, in an attempt to study and understand the risks posed by in-mine seismic events and to subsequently use the knowledge gained to mitigate these risks. In December 2007, an M2.2 event occurred at Mponeng and was detected by the tiltmeters installed. The tilt expected for the M2.2 event is modelled through the use of numerical and analytical tools and utilizing, as input parameters, characteristics of the event such as the rupture area, the amount of slip, elastic properties of the rock, the state of stress before the event occurred, and frictional parameters of the rupture. The calculated tilt values are correlated and compared with the recorded data, and are found to be of the same order. Certain input parameters, such as the initial rupture point, are further constrained by varying them, during modelling, until the calculated and observed tilt values are approximately equal. From modelling, it can be concluded that the rupture point had to be closer to the location of the tiltmeters. In addition, possible locations acting as source areas for the observed aftertilt are determined. Further modelling still needs to be done to quantify the effects of the tunnel close to the tiltmeters and plastic deformation of the rock mass. Keywords high-resolution tilt data, Mponeng gold mine, M 2.2 seismic event, analytical modeling, numerical modeling, rupture plane.

Oct 1, 2013

By B. Genc

"The risk of spontaneous combustion is well known in the South African coal mining industry. In the coming years it is very possible that the incidence of spontaneous combustion will increase from current levels, due to factors such as an increased rate of mining, re-working of previously mined seams, more stooping and total extraction for underground mines, and higher stripping ratios for surface mines, leading to more spoils. It is also fairly certain that coal mining will face tougher environmental emissions legislation in the near future. To determine the areas where the risks of spontaneous combustion are high, it is necessary to improve on our current laboratory procedures for testing and evaluating coal samples, combining the results with site and field data, and if necessary revising the laboratory rating system to refine our understanding of South African conditions.Currently, laboratory tests are conducted in order to determine both the Wits-EHAC index and the crossing-point temperature which, when combined, give an indication of the spontaneous combustion propensities of the coal samples. This procedure has enabled the establishment of a database of results to review and evaluate South African coal seams. Using this database, the high-risk areas in terms of spontaneous combustion are identified. Tests have been undertaken for five consecutive years, between 2008 and 2012. In total, 119 coal samples from different coal seams and production coalfields have been analysed and classified through a series of laboratory tests. A comprehensive database of these results is available, and is continually being updated as new test results are added. This database will continue to expand, and to provide the basis for an improved risk evaluation methodology for spontaneous combustion"

Jan 1, 2015

By J. N. Van der Merwe, M. Mathey

"The South African squat coal pillar strength formula, developed by researchers from the Chamber of Mines Research Organization in the 1980s, predicts an exponential increase in coal pillar strength once a critical width-to-height ratio of 5 is exceeded. The arguments that have been proposed in favour of this formula are discussed critically in this paper.Field experience with squat pillars in the USA and evidence from published physical, analytical, and numerical model pillar studies corroborate the fact that a squat effect is unlikely to occur in coal pillars at width-to-height ratios less than 10. Furthermore, an exponential increase in peak strength of coal pillars does not exist. An alternative design criterion for squat pillars in South Africa is therefore suggested. IntroductionFive decades of coal pillar research in South Africa have produced a wealth of information on the mechanisms contributing to the strength and failure of in-situ coal pillars and accompanying phenomena. The relevant knowledge was sourced from, and for, a South African coal mining environment that remained largely unchanged in the second half of the 20th century. The depth of mining seldom exceeded 250 m, with mined seam thicknesses averaging 3 m and typical pillar width-to-height ratios (w/h) of 3–4.It is therefore not surprising that comparatively little research has been directed at the prediction of coal pillar performance in deeper deposits, where squat pillars of larger width-to-height ratios will be required to support the overlying strata. However, a thorough understanding of squat pillar performance will be necessary should the remaining deep coal deposits of the country be extracted in future, for instance in the Waterberg or Ermelo coalfields.A squat coal pillar strength formula has already been proposed in South Africa. The origin of this formula will be discussed in some detail in the following sections and its appropriateness will be critically reviewed against a great amount of evidence from relevant squat coal pillar research conducted internationally."

Jan 1, 2016

By I. J. Barker

Keywords: Submerged-arc furnace, plasma furnace, d.c. furnace, scale up, Søderberg electrodes, smart grid, demand side management, load shedding This paper argues that the scale up of furnaces and the supply of electricity are going to be two major issues that will affect the ferro-alloy industry in the near future, and that economic factors will drive this development. The most common type of furnace for producing ferro-alloys at present is the submerged-arc furnace with three electrodes, fed from a three-phase a.c. electrical supply. The scale up of this technology has now reached a fundamental constraint, which is caused by the electrical reactance of the secondary circuit. If the economy of any further scale up is to be achieved in the future then a different technology will have to be used. The supply of electrical power in future is likely to become a more complex issue than it is at present. Existing submerged-arc furnaces tend to run at fairly steady loads, but the ability to swing the load under demand-side management may offer advantages, and may allow a furnace to get cheaper power from the organisations that supply this power. This will have to be counterbalanced against the nuisance factors incurred by having a varying load in the operation of the furnace. Various options are therefore discussed in this paper. The possibility of scale up of Søderberg electrodes is discussed, as well as the use of d.c. power and multiple electrodes. Some of the issues with load swinging are also examined. A particular scenario is also briefly presented to show that considerable further scale up of ferro-alloy furnaces is still possible.

Jan 1, 2011

By H. T. Ozkahraman

It is important to know the breakage mechanism in materials since this knowledge influences the results of subsequent grinding operations. There are two distinct failure mechanisms in breakage: one is tensile micro crack generation at low stresses, which leads to macroscopic failure by disintegration, and the other is formation of shear zones under heavier dynamic impact forces, which generates more fines as seen in crush zones in blasting. Tensile fracturing simply breaks the material into fragments. It is seen as the disintegration of the specimen into two or more separate fragments. This happens under the absence of lateral stresses and the material is free to expand. On the other hand, compressive-shear breakage produces finer fragments due to shear stresses. The first mechanism is observed in laboratory tensile and bending strength tests and the second mechanism is observed both in laboratory brittleness tests and in situ blasting operations under dynamic impact forces. The friability of rocks and ores can be determined by a brittleness test. A test apparatus to determine the friability value has been designed to suit limestone strength characteristics used in cement production. The friability and stored strain energy values of barite, marble, limestone and bauxite have been determined and compared with the corresponding Bond work index (Wi) and grindability index (G) of these materials. The physico-mechanical properties of the tested materials have also been determined to investigate their effect on friability and grinding. The relationships obtained between the indices were in surprisingly good agreement, with high correlations (0.99 and 0.97). The Bond work index and grindability index can therefore be estimated from the friability value, which can be determined more rapidly than the Bond test. But for certain rock types such as andesites the relationships does not hold. Key words: comminution, tensile stress, shear forces, brittleness test, strain energy.

Jan 1, 2010

By M. Dworzanowski

Beneficiation, in the context of this paper, has two distinct definitions. From an economic perspective, beneficiation relates to adding value to a mined raw material. From a metallurgy perspective, beneficiation relates to processes used to upgrade the mined raw material. Clearly then, ?economic beneficiation? is dependent on ?metallurgical beneficiation?. South Africa possesses the world?s largest mineral resources by value and is a significant global producer of many mined commodities. Significant metallurgical beneficiation of ores does occur in South Africa. The role of metallurgy in economic beneficiation will be examined in terms of current practice and the potential for expansion. South Africa?s main mining commodities will be covered ? namely gold, platinum, coal, iron ore, manganese, chromium, vanadium, copper, nickel, titanium, zirconium, uranium, and diamonds.

Sep 1, 2013