Search Documents

By M. I. Brittan

Discussion Dr R. E. Robinson (Fellow): The author must be congratulated on a very meticulous and self-contained piece of work. It is indeed a pleasure to read a paper that is so clearly and systematically laid out, and where the conclusions and the testwork conducted have been so clearly described. The paper is complete in itself, which makes it very difficult for someone who is not intimately involved in the whole Torco project to make any comments on its content. However, two points that, strictly speaking, fall outside the scope of the paper are of considerable interest. The first relates to the particle size of the material treated. In the paper, the testwork is confined to one standard particle size (minus 60 plus 100 mesh). The essential feature of the paper is to indicate that the rate-controlling reaction in the whole segregation process is the rate of reaction of the ore particles with the reducing agent and the hydrogen chloride. One wonders, therefore, to what extent this relatively slow rate of reaction is affected by the particle size of the ore itself. One imagines that the reaction must take place by contact of the hydrogen chloride with the surface of the mineral particles, and it is reasonable to suspect that the rate of diffusion of the copper ions to the surface is a relatively slow process and is thus the limiting factor in this particular rate of reaction. It is possible, for example, that the improvement obtained, when the ore is subjected to reducing conditions before the chlorination, is due to a breakdown in the crystal structure of the original particle. This breakdown is brought about by the reduction and by the consequent increase in surface area available for reaction with hydrogen chloride. Can the author indicate whether any work has been done along these lines, and whether it has been established that the reaction depends on the surface area available? The second point relates to the application of this kinetic study to the actual operation of a Torco reactor. It was once planned to feed the sodium chloride, together with the reducing agent, into the top of the segregation chamber. In the paper, the author mentions that it has now been established that the segregation chamber behaves, to all intents and purposes, as a fluidized bed, and that there is, therefore, a rapid evolution of gas in the lower regions of the chamber, which, it is imagined, displaces the gas phase rapidly. Since the reaction between sodium chloride, water vapour, and the aluminium silicates in the ore is extremely rapid, one wonders how much of the hydrogen chloride produced is removed from the reaction zone before it has had time to react with the copper minerals. The extremely low consumption of sodium chloride (which is a vital feature of the Torco process) must depend on an extremely rapid circulation of the hydrogen chloride gas to all the ore particles in the segregation chamber. One wonders, therefore, if a system for the introduction of the sodium chloride into the bottom regions of the chamber might not result in even greater efficiency in the utilization of sodium chloride. ProC D. D. Howat (Fellow): All of us who have been concerned with the study of chemical reactions at high temperatures are keenly interested in kinetics and are well aware that this is not an easy study experimentally. Dr. Brittan is to be congratulated on the development of neat experimental methods and for his full discussion of the results obtained. Although the segregation process for the extraction of copper from oxide and silicate ores has been known for almost fifty years, the fundamental chemical and physical changes involved have been little understood and the fundamental data are very scanty. The work now in progress at A.A.R.L., together with that sponsored by the Anglo American Corporation in other research institutions throughout the world, is bound to produce new fundamental data and a much more complete understanding of this rather fascinating process. It is already apparent that some of the old and well-worn chemical reactions that were postulated to occur, just cannot take place in the way which was formerly accepted. Dr Brittan's work, carefully conducted and thoroughly analyzed as it has been, still leaves us with one great outstanding problem. The thermodynamic data and the possible reactions set out in Table I (page 281) of his paper leave us asking, in complete despair, how can copper be converted into a volatile chloride in the presence of HCl, CO and carbon at temperatures about 800°C? The thermodynamics all combine to show that copper should be reduced to metal as the first step in the process. This brings us right up against the second problem. If copper were reduced to the metal how would HCI convert it to the volatile chloride? On top of these problems is the unknown reason for the very high speed of reaction between CO, HCI and the ground copper ore. Still further into the region of the unknown is the reaction by which gaseous hydrochloric acid is produced in the actual process. Perhaps Dr Brittan is feeling grateful that he doesn't have to try to explain this reaction-at this stage of the research programme at least. The results very clearly show that both CO and HCl gas are essential for rapid production of the volatile copper chloride. Dr Brittan states that 18 minutes were required to attain 83 per cent extraction with HCl gas alone and this was reduced to 4 minutes when CO was

Jan 2, 1970

The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 26th August, 1970, at 4.15 p.m. Mr. J. K. E. Douglas (President) was in the Chair. There were also present sixty-three Fellows, thirty-five Members, one Graduate, eight Associates, five Students and nineteen Visitors, making a total of one hundred and thirty-two. The President declared the meeting open at 4.20 p.m. OBITUARIES The President: 'It is my sad duty to announce the deaths of the following members of the Institute. Dr J. A. Papenfus, Fellow, who joined the Institute in 1942 and passed away on the 28th of May, 1970. Mr D. G. Beadle, Fellow, who joined the Institute in 1946 and passed away on the 17th of June, 1970. Gentlemen, Derek Beadle was very well known in this Institute. His papers on dust will be remembered and, at the time of his untimely death, he was one of our assistant editors. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I would ask you to rise and observe a few moments' silence.' MINUTES The President: 'May we confirm the minutes of the General Meeting held on 15th April, 1970, as published in the July, 1970, issue of the Journal'. Agreed. WELCOME TO VISITORS The President: 'Ladies and Gentlemen, we are honoured this afternoon by the presence of many distinguished guests and I extend to you all a most cordial welcome. We are happy to have with us Dr A. A. von Maltitz, President of the Chamber of Mines of South Africa, who is also Honorary President of this Institute. We also have one of our Honorary Vice-Presidents, Mr T. L. Gibbs, the Government Mining Engineer; Mr D. E. Hamm, President, Institution of Certificated Mechanical and Electrical Engineers, S.A.; Mr S. C. M. Naude, Director, Witwatersrand Technical College; Mr I. R. G. Stephen, Senior Vice-President, The S.A. Institute of Electrical Engineers; Mr G. M. Tompkins, President, The S.A. Institution of Mechanical Engineers; Professor P. B. Ackermann, President of the Geological Society of S.A.; Mr A. S. Robinson, Vice-President of the S.A. Institute of Civil Engineers; Professor W. Mare, President of the Institute of Land Surveyors of the Transvaal; Mr B. D. Charlton, President of the S.A. Institute of Assayers and Analysts; Mr R. Hemp, The President, The Mine Ventilation Society of S.A.; Mr L. J. Prince, The President, The S.A. Association of Mine Managers; Mr J. Botha, The President, The S.A. Institute of Foundrymen; Mr G. Niterl, The President, The Institute of Welding; Mr M. R. Gericke, President, S.A. Council of Professional Engineers; Mr N. A. Honnet, Chairman, Orange Free State Branch; Mr P. R. C. Cooke, Chairman. The South African Chemical Institute (S. Tvl. Section). Gentlemen, we are very honoured indeed, to have these distinguished gentlemen with us this afternoon, as our honoured guests. We are also pleased to have with us, one of our Honorary Fellows, Mr F. G. Hill, and several Past-Presidents. I also extend a very warm welcome to all our lady guests and to all our other visitors.' MEMBERSHIP The President: 'I have pleasure in announcing that the names of the following candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership in the following grades: NEW APPLICATIONS Fellows: Herbert Dalton-Brown, Stephen William Morel. Members: Clive Lester Workman-Davies, Basil James Russell Botha. Students: Timothy Nigel Watson, John William Hair-bottle. I wish to welcome the new members to the Institute and to congratulate those members who have been transferred to a higher grade.' ANNUAL REPORTOFTHE COUNCILAND ACCOUNTS FOR THE YEAR ENDED 30th JUNE, 1970 The President: 'I now have pleasure in presenting to you, the Annual Report and Statement of Accounts for the year ended June, 1970. These have been handed to you this afternoon and, as is customary, I propose they be taken as read. Before moving their adoption, however, I would like to refer to some of the salient features, leaving as is usual, the task of dealing with the finances, to our Honorary Treasurer. It is encouraging that membership has continued to grow, and now stands at 1,613, an increase of 61 over last year's total. Your Council, however, is aware that there are still people in our mining and metallurgical industries, who could qualify for membership, but who have not yet joined the Institute. A drive to increase membership was accordingly organised, and members of Council were given the responsibility for campaigning in sections of industry, and for publicising the objectives and advantages of belonging to the Institute. Up to now there has not been much reaction to this campaign, but I hope we will see results in the coming year. At the same time, Council has recognised the need for change in the conduct of the Institute's affairs in order to meet the changing needs of our membership. Our members, both mining and metallurgical, are in the first place, geographically more widely dispersed than they used to be, and secondly, with the growth of the metallurgical industry, their technical interests are now more diversified. The Institute must cope with these changing needs if we are to continue to perform a useful function. The

By E. Mpoloka

Debswana together with ADP as their design partner have embarked on an RDP project at Jwaneng Mine. The objective of the project is to install a 2 million ton per annum mineral processing plant that will fast track the recovery of diamonds from the Debswana tailings resource to ensure maximum return on investment for the company. Due to the prevailing economic conditions Debswana has had to review the way they used to build plants in the past and consider simple, fast and effective ways of doing things. The rapid deployment plant concept is therefore the most suitable means of achieving this objective. Debswana is also considering an operating partner who will operate far more efficiently and cheaply compared to the larger more cumbersome and less agile Debswana.

Jan 1, 2010

"Chairman: Prof A. E. H. BLEKSLEY Rapporteur: Prof J. ELBRONDPanel Members: Prof J. C. Griffiths, Prof T. E. Hawkins, Mr A. C. Langton, Mr M. Splaine, Mr A. WeissThe reasons for failure of computer applications in the mineral industry and the direction of future developments.The Chairman opened the discussion by elaborating on the disappointment felt by some authorities with the lack of progress in the application of computers in the mineral industry during the last ten years, and posed the question to the panel : 'Do you agree that the computer age has not come up to expectations?'Mr Langton said that although there seemed to be a tremendous amount of brainpower applied to the theoretical side, he thought that the production men had not got all the help from computers that could have been given to them. The computer, said Prof Griffiths, is as yet a new tool which should not be used to do old things in old ways. To learn to use the computer will take time. After all, he said, it had taken 400 years after the introduction of the printing press to achieve general literacy, and perhaps it will take 40 years after the introduction of the computer to achieve `numeracy'.In Mr Weiss' view, the reason for the feeling of disappoint¬ment lay in the focussing of attention on the computer. The blame, if any, lay with the people surrounding the computer, that is, the analysts and programmers, to whom the emphasis should be shifted.Prof Hawkins said that he thought that some applications of the computer in the mineral industry had been successful, such as, for example, the compilation of payrolls. Reasons for failures in other areas were to be sought in the fact that the people connected with computers had failed to realise that they were merely part of a system. They had not understood the power structure of the organization which their work tended to change, and were therefore not prepared for the inevitable conflict with the production men.In Mr Splaine's view the production man had not received the assistance he could have had from the computer people because he may possibly not have allowed this to happen.Prof Bleksley concluded from these opinions that the promise which computers had ton years ago had not been fulfilled and added that the opinions expressed by the panel had intruded on his next question which was: 'Is the reason for this that people are involved?Prof Hawkins elaborated on his previous theme, namely, that of computer people in relation to management. Com-puter people, he said, were trying to impose change on management but were not prepared to share the responsibility for these changes. In fact, they wanted their work to be distinct and separate, and, as far as management was concerned, changes would be made when management believed that these would be less agonizing than no change at all."

Jan 1, 2014

"Chairman: Professor H. S. SICHEL Rapporteur: Miss M. I. WATSONPapers:Unrolling of Copperbelt orebodies by J. H. E. Perry and V. H. WiikAn exploration model for tabular orebodies by G. S. Koch and R. F. LinkHarmonic analysis of copper and gold occurrences in the Arbitibi area of the Canadian Shield by F. P. Agterberg and A. G. FabbriMathematical models of orebodies by M. J. Newton and A. G. Royle Estimation of lateritic-type orebodies by A. JournelIn his presentation Mr Wiik said that unrolling could be regarded as a reversal of the natural process of folding, so that the aim of an unrolling procedure would be the reconstruction of original pre-tectonic conditions. While simply formulated, this aim might not always be achieved. The geometrical relationship between points on the deformed surface and corresponding points on the original surface is process-dependent, and a true reconstruction could be achieved only if the deformation history were known in detail.In this computer unrolling procedure all these complexities were ignored. Referring to one particular marker horizon, Mr Wiik said that it was assumed in the procedure that this marker was deposited as a horizontal stratum and that it had subsequently been deformed by simple flexure-type folding.The procedure allowed the geologist to incorporate his knowledge and conception of the deposit through repeated re-contouring with dummy points. This 'manumatic' aspect of the procedure had proved invaluable, not only in resolving specific unrolling problems but also in making the system more acceptable to the geologists in general.Unrolling served towards removing what might be termed `tectonic noise' superimposed on the primary distribution patterns for regionalized variables such as metal content and orebody thickness. From this point of view, variograms derived on the basis of unrolled-plan co-ordinates should be more meaningful in terms of depositional environment than are variograms calculated from a normal map projection.Mr M. M. Oosterveld remarked that it appeared from the paper that there were problems in applying the unrolling technique to ore reserve calculation, and asked whether there were not other methods that might be used for that purpose.Mr Wiik replied that at present unrolling played only a minor role in practical ore reserve estimation within Roan Consolidated Mines, Limited. The techniques currently in use differed from one orebody to another, but in general they involved projection onto a vertical longitudinal section or a horizontal plan, with subsequent grid interpolation by means of a standard computer contouring package."

Jan 1, 2014

By R Linares

For centuries, diamond's superlative properties have earned it a reputation as the 'dream' material for mankind in its search to create advanced applications. Until recently, this dream has been realized only in the use of diamond for gemstones and abrasive applications where several tons of diamonds are now used on an annual basis. The vision of having large, high quality diamond as part of a broad engineering tool-kit for many diverse high tech industries is now becoming a reality however, with the advent of early stage commercial availability of single crystal and poly crystalline CVD diamond.

Jan 1, 2010

By R. G. Coyle

"In an earlier paper the author explored the consequences of price-stabilizing effects, on an industry-wide basis, of various production strategies. These ideas have now been applied to an illustrative case of an individual mine. It is shown that the turning of production and financial policies can affect financial performance over a five-year period by as much as 22 per cent.No generality is claimed for the results and they would differ from mine to mine. It is, however, asserted that the results show that the proper turning of production, reserves and financial policies are more critical determinants of mine performance than has been realised. It is also asserted that the methods of dynamic analysis are the most appropriate means for studying this policy-design problem."

Jan 1, 2014

By S. Polansky, J. Kolacz

The new sorting system has been developed to achieve efficient separation at low mineral content levels. The system employs high resolution X-ray sensors providing multi-energy analysis, thus giving maximal information about processed materials measurable by X-ray radiography. It makes it possible to analyse the internal structure of the particles and directly detect inclusion of minerals and metals like copper or gold. The paper describes sorting application examples for zinc, lead, copper and gold ore with low metal content below 0.1% of Cu. The sorting system still allows high efficiency analysis, quantification and removal of rock particles representing waste fraction with no metal or a negligible amount being uneconomic to process. This brings a huge advantage during pre-concentration, where almost no losses of valuable minerals in the waste fraction can be achieved. The presented sorting system has been developed by Comex and X-MINE EU Project Consortium. Keywords: X-ray sorting, ore sorting, XRF analysis, XRT analysis

Jan 1, 2020

By M. Ndabeni, J. H. van Vreden, M. Le Roux, Q. P. Campbell

It is not uncommon for gold slurry ponds or screen oversize dumps to contain several different types of carbon-rich contaminants. These contaminants act as robbers of dissolved gold which has a detrimental effect during the downstream carbon-in-leach (CIL) or carbon-in-pulp (CIP) processes. With a renewed interest in the reprocessing of contaminated gold waste ponds and dumps, preconcentration of the feed to either the CIL or CIP process becomes important to maximise profits from these resources. An added advantage in removing these resources, which were once thought of as being uneconomical, is the availability of land that can further be rehabilitated for community development projects. For gravity separation, an example of suitable technology is the Reflux Classifier (RC), which can be used for the separation of materials of different densities and can be used as a pre-concentration step. In this project, a laboratory-scale Reflux Classifier was used to pre-concentrate a gold-bearing sample obtained from a waste dump situated to the east of Johannesburg, South Africa. The material had an average gold grade of 1.9 g/ton and a carbon content of 10%. This material was first fed to a semi-batch Reflux Classifier that was used to fractionate it into several different density intervals by varying the fluidisation water feed rate, followed by continuous runs at fixed water flow rates. The results showed that a cumulative gold recovery of 60%, carbon recovery of 85%, and mass pull of 41% was possible for a fluidisation water feed rate of 15 L/min, while a rate of 20 L/min resulted in a gold recovery, carbon recovery and mass pull of 83%, 92% and 79% respectively, which translated into a concentrate gold grade above the set target of 3 g/ton. Continuous operation at 20 L/min yielded an underflow stream with 84% gold recovery at a grade of 5.4 g/ton. Keywords: Reflux Classification, gold recovery

Jan 1, 2020

By D. A. Phillips

A procedure for designing an optimum pit to yield maximum profit is described. The volume in which a possible pit is considered is divided into discrete blocks, each of which is assigned an economic value equivalent to its worth as a block of mineable material. The profitability of a pit can then be generated by summing the blocks within the pit. The optimizing procedure starts at the surface level and proceeds downwards level by level, to obtain the optimum pit at each level. The method makes use of the fact that an optimum pit at a particular level must be completely contained in any optimum pit at a lower level. Procedures for generating block costs, and pits with various slope angles under the restriction of complete block removal are considered briefly. The main description is of the theory of the method and the computer program based on this. The method is applicable to any type of mineral deposit, the only requirement being that the orebody should be represented accurately by a block model.

Jan 1, 2014

By L Dyer, G. J. Wilkie, P. Walters, B Tadesse, L. Keeney

Grade Engineering® is a term trademarked by the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) and includes five key levers for upgrading ores and rejecting waste prior to expensive downstream comminution and mineral processing. These five levers include natural deportment, induced deportment, bulk sorting, particle sorting and gravity separation. Over the past ten years, CRC ORE has progressed a range of technologies that exploit these levers from laboratory proof of concept through to large scale demonstration and validation. This paper details the work carried out by CRC ORE and Curtin University for assessing the amenability of an ore for its natural deportment and particle sorting attributes in an Integrated Screening and Particle Sorting (ISPS) Grade Engineering® process. ISPS is seen as a preferred method for Grade Engineering® as compared to individually operated unit operations as the benefits of each can be complementary. Furthermore, it is suggested that integrating the two levers has two important impacts: 1. Firstly, there is a risk that isolated particle sorting test results will be misinterpreted as being representative of the full sample without considering the mass balance impact of high-grade material that might have been lost in the fines fraction. This fine fraction will not be detected through the particle sorter. 2. Secondly, and potentially of more valuable impact, is that the opportunity may exist to upgrade the feed first through determining if there is a concentration of high grade to the fine (or coarse) fraction which can be separated through screening. Undertaking screening in the preparation stage of the particle sorting process will enable analysis and separation of the fine or coarse fractions of a rock mass. The result of this study provides the mining industry with an independent framework for undertaking an Order of Magnitude (ISPS) Grade Engineering® assessment on a range of constituent ore types. Keywords: Grade engineering, particle sorting, grade by size fractionation

Jan 1, 2020

By P. L. Moolman

An approach to the design of a tailings disposal system is presented using an example from a platinum project on the eastern limb of the Bushveld Complex as a base case. The design is driven by two inputs: namely, maximizing water recovery and minimizing power cost, expressed as cubic metres and kilowatts per ton of solids deposited on the tailings storage facility respectively. The approach considers low-, medium-, and high-density platinum tailings and uses material-specific aspects such as thickening and rheology to determine the most economical option. An analysis based on direct capital and operating cost (water and electricity) shows that the medium-density scenario results in the lowest total cost per ton of tailings deposited, even though this system results in the highest electricity consumption per ton of tailings deposited. As the cost of water and electricity is likely to increase in the future, the higher-density tailings disposal options become more economical, with the paste option the preferred option.

Jan 1, 2012

By G. D. Rosales, P. F. A. Braga, S. C. A. França, C. P. Pinto

The growing market demand for lithium is mainly due to its use in the manufacture of batteries for electric or hybrid vehicles and portable equipment (smartphones, tablets, power tools, notebooks, etc.). Currently there is great interest in finding new sources of lithium and technologies for its utilisation. Li-S batteries have received attention due to their theoretically high specific energy density, which is 3 to 5 times greater than that of Li-ion batteries. Unlike Li-ion batteries, of which the main raw materials are lithium carbonate and lithium hydroxide, the main raw material for Li-S batteries is lithium chloride. The anode used in Li-S batteries is metallic lithium, produced by a molten lithium chloride electrolysis process. The extraction of lithium from pegmatites such as spodumene, previously abandoned in the 1990s for being uneconomical, has become attractive due to the increase in prices as well as the need for greater lithium purity of products made from lithium-bearing minerals. The main methods used for lithium recovery from spodumene ore include the sulfuric acid process, the alkaline process (lime or limestone as raw material) and the chlorination roasting process. Thermodynamic modelling using HSC software 5.1 was conducted to predict different reactions that could occur during chlorination roasting of the spodumene/MgCl2+CaCl2 system. Lithium extraction from the solid obtained after the chlorination roasting was also investigated. The results of thermodynamic analysis provided a better understanding of the chlorination roasting process for lithium extraction. Metallurgical tests with a mass ratio of 1:6 (spodumene:chlorides) and molar ratio of 2:1 (MgCl2:CaCl2) allowed over 95% recovery of the lithium contained in the spodumene concentrate. Keywords: Spodumene, lithium chloride, chlorination roasting

Jan 1, 2020

By S. Langea, H. Lieberwirth

Impact crushers are common machines in comminution plants. Their high size-reduction ratio and relatively simple design, make them a preferred tool even when subjected to harsh wear, and producing a large quantity of fines in some applications. Until now the alignment of the operational parameters was an operator’s responsibility. Due to the random process characteristic this is mostly done based on empirical values and sensor data, such as power consumption. This paper describes a new approach for online process monitoring of the horizontal-shaft-impact crusher. The application of robust, low-cost acceleration sensors enables the permanent observation of the process characteristics. The operational and evaluation methods are determined on the basis of experiments. Subsequently the recorded measurements are analysed in regards of throughput, rotational speed and product particle size distribution. Occurring signal characteristics are described based on physical and technical principles. The measured data of the acceleration sensors at varying operation conditions provide insight in the course of process. The accurate utilisation yields the determination of the preferential process conditions providing the best balance between the pros and cons of an impact crusher. Both the experimental method and the data processing is discussed from a scientific perspective, displaying a completely new approach for the operation of impact crushers. Keywords: Impact crusher, acceleration sensors, data processing, particle size

Jan 1, 2020