Search Documents

By S. C. Essack

"Tenova Pyromet has designed a slag flow control valve that throttles the flow of slag in order to control the tapping rate. In addition, the valve has proved to be a reliable tool for closing the furnace during normal operation as well as emergency conditions. The valve makes use of a water-cooled copper element that is hydraulically operated and attached directly to the slag tap-hole. The equipment is compact, simple to maintain, and cost-effective to purchase and install. It can be retrofitted to most existing slag tapholes with minimal modifications.During the development phase, finite element method (FEM) and computational fluid dynamics (CFD) software was extensively used to model predicted operating conditions and to optimize the design. By using CFD, it was possible to understand the flow patterns inside the copper and to optimize these to improve overall performance.The slag valve was installed and commissioned in 2011/2012 on a 12 MW furnace as part of a new mineral wool plant in the USA. It has performed well since its installation despite operating under conditions in excess of the original design criteria. During the first 6 months of operation it quickly became the preferred method of closing the furnace, although the design intent was for occasional use during emergency shutdown conditions only. Since replacing the mudgun as the main method of closing the tap-hole, a few minor changes have been made to the installation in order to cope with the increased heat load and much higher frequency of use."

Jan 1, 2014

Deciding on plant-scale reagent dosage regimes and air rates is a topic of ongoing investigation and high importance. The current work explains some techniques that have proven useful in deciding on plant-scale flotation operating regimes. Specific focus has been placed on the reagents: frother and depressant, as well as some discussion around the control of air rate and froth depth. Air rate has been selected based on its effects on the froth phase. Froth velocity and froth height above the cell lip are the two variables measured and used to select the operating air rate. Pulp level is then adjusted to increase or decrease mass pull. A technique has been developed using the Anglo Platinum Bubble Sizer on an industrial flotation cell to determine the relationship between bubble size and frother concentration. This technique has been extended to measure the equivalent frother concentration or frothabilities of various streams on a rougher bank. A mass balance for frother was performed successfully, and this provided a better understanding of the way frother moved in the rougher bank. With this knowledge, more informed decisions can be made about frother addition required in subsequent flotation stages. For depressant, a new protocol for deciding on dosage rate has been developed. The depressant dosage should be based on the amount of fresh feed material reporting to a bank. Currently 400 g/t of fresh feed has been assumed a reasonable starting point with promising results. Improved froth stability and grades were observed. There is scope for more accurately defining the optimal dosage rate. Importantly, the combined effect of changing the chemistry and the hydrodynamics together has been demonstrated. A significant upward shift in the grade-recovery relationship for a cleaner bank was observed.

Jan 1, 2012

By J. E. Chilton

No regular monitoring of methane is required in areas of gassy coal mines outby the mining face. Methane ignitions that have occurred in mine outby areas indicate the need to provide better protection to workers. Handheld methane monitors are now used by some miners to make periodic measurements of methane at the working face. The IYONI II gas detector which is incorporated into a miner’s cap lamp and worn on a miner’s helmet can continuously provide an alarm signal whenever methane levels exceed a set level. Tests were conducted to evaluate the performance characteristics of this methane detector by measuring response times with methane gas supplied through a calibration fixture or adaptor. Other response time tests were performed with the detector in an environmental test box. Performance was also evaluated in a full scale test gallery where face methane emission and underground ventilation were simulated. Procedures for calibration by response time measurement of the IYONI II detector have been developed. In limited testing, the IYONI II detector was found to reliably detect the presence of 1 percent by volume methane.

Jan 1, 2003

By C. Montoya

This paper shows, through a case study, the impact of multivariate grade modelling upon mine design and mine planning. A deposit explored by drill holes is considered, in which the grades of five elements (copper, silver, molybdenum, arsenic, and antimony) are of interest. Forty alternative models of the deposit are constructed by fitting the joint correlation structure of the grade variables and using conditional cosimulation. In addition, a reference model, obtained by averaging the alternative models, is also considered. The study shows that the resulting mine design (final pit characteristics and production schedules) is sensitive to the grade model under consideration, and that the design based on the reference model may not be optimal when compared to the alternative models based on cosimulation. However, when assuming a given long-term plan and extraction sequence, the grades and net present value (NPV) calculated on the reference model are unbiased with respect to those calculated on the alternative models with the same extraction sequence. The latter allow assessing the possible dispersion of the actual grades and NPV around their expected values, and are useful for the planner in order to determine the probability of meeting given production targets and of exceeding or falling short of given threshold grades. Additionally, unlike cosimulation, the separate simulation of each grade variable leads to unrealistic resource models and to biased results in mine design and mine planning. This approach should therefore be avoided, unless the grade variables are spatially uncorrelated.

Jan 1, 2012

By V. Oberholzer

The presence of fines (particles smaller than 6 mm in diameter) causes hydrodynamic problems in gasifiers and therefore it is of great importance to minimize the amount of fine coal in the feed. This serves as motivation for understanding coal?s breakage mechanisms, which could lead to the ability to predict the generation of fines. The aim of this project was to simulate the pulsating effect of the conveyor belt in order to investigate factors influencing the breakage. Results indicated that an increased initial particle size had an increasing effect in the amount of fines generated. Weathering had an insignificant effect on the breakage of coal. To conclude, a breakage model was developed to describe the rate of breakage out of the top size when a combination of two breakage modes is present.

Jan 1, 2009

By P. N. Erasmus

This paper considers the fundamental concepts of support design for underground openings in highly stressed ground. It concludes that the conventional deformed reinforcing bar, woven mesh and cable lacing support methods that have been widely used in deep gold mines are quite in appropriate for the support of highly stressed tunnels. The following is suggested as the criterion for adequate dynamic support under rockburst conditions: the energy absorbed by a support unit (yielding through some acceptable limited displacement) should exceed the kinetic energy generated by the mass of rock that is intended to be retained by that unit. Duraset in conjunction with SRK Consulting has developed a yieldable steel tendon called the Durabar®. It is unique in the sense that it cleverly utilizes the property of the ductility of ordinary low-carbon steel from which it is made to accommodate the excessive displacement it is subjected to in the case of rockbursts or swelling ground.

Jan 1, 2009

By Thermo Electron, Tim Sennett

Summary ?SamStat Development ?SamStat Description ?Accuracy ?Availability ?Cost of ownership ?Capital ?Installation ?Operating/Maintenance ?Case Studies ?Modikwa ?Combined concentrate sampling ?Cerro Verde ?State of the art sampling & analysis ?Ok Tedi Final Tails ?brownfields installation ?Conclusion

Jan 1, 2005

Geologists in some underground gold mines collect grab samples from broken ore piles or trucks as a method of grade control. It is often known as muck sampling. Generally, the goal of grab sampling is to try and reconcile the mined grade at the ore source to the predicted grade and/or predict the mill feed grade. The mass of the sample collected is limited by health and safety issues, as well as the capacity of the laboratory to process the samples within a given timeframe. In general terms, grab sampling is known to be problematic because samplers tend to over sample the fines, and/or pick out high-grade fragments; surface sampling of piles does not test material within the pile; muck piles in development drives/faces are likely to be zoned due to the blasting sequence; high or low-grade material may preferentially segregate in the pile during mucking; the five percent mass reject size of the material in muck piles is very large from underground blasting; some correlation usually exists whereby the larger fragments are enriched or depleted in the critical component of value; and the average error made in estimating the true stockpile grade is likely to be high. The method is prone to chronic fundamental sampling, grouping and segregation, delimitation, and extraction errors. Substantial warnings must be given with respect to the use of grab sampling for grade control in gold mines. The method may appear to work sometimes, which can be attributed to a fine gold particle sizing and more disseminated distribution. As with all sampling methods, its appropriateness must be determined by ore characterization and heterogeneity testing to ensure the method suits the ore type.

Jan 1, 2009

The peak in Sulphur price late 2008 caused again intensified investigation into the decomposition of sulphates and spend acid. One option is the recycling of sulphur from spend acid, which already started more than 40 years ago in the field of spend acid from organic processes in refineries and acrylic glass manufacturing. Since this acid couldn't be neutralized and discarded due to high organic contents, another source of SO2 to produce sulfuric acid is the decomposition of metal sulfates. The decomposition of metal sulfates was investigated at the next peak in Sulphur price in the 80?s. The first major scale pilot tests and studies of gypsum decomposition were carried out for clients in Florida. The decomposition of gypsum was quite often mainly influenced by the strategic decision of some countries to get own and independent acid production. In other cases the industry doesn?t have enough space to dump the gypsum. Therefore the company was also forced to convert the gypsum into ?saleable? products to avoid these residues. Other projects were made for the recycling of iron-sulfates from the pigment industry. The motivations for these projects were not only given by acid price. For the German pigment industry it was no longer permitted in the 80?s to dump the iron sulphate residues into the sea. These regulations forced the industry to develop new technology, which allows converting of the FeSO4-residues into iron oxide and acid. Therefore economical and mainly environmental factors influenced the decision of the companies to develop and to build these plants. Beside the above mention iron- and calcium-sulphates many other process exist, which produce metal sulphates as an intermediate product. These cases are not forced by environmental or strategic factors. In cases like Ni, Co or Mn-decomposition the main product of the plant is treated in the decomposition plant and later on used as ferrous-alloys. These final products are higher in price compared to e.g. CaO, which exclude the high-energy consumption for the endothermic chemical decomposition reaction. The reaction of SO2 generation based on acid or sulfate decomposition takes place in the range of 1000°C. The energy demand of the endothermic reaction is considerable and leads due to the high fuel-combustion off-gas stream to a diluted SO2 gas. Energy prices are usually increasing at the same time like sulphur. Sulphuric Acid based on decomposition is therefore more expensive than as acid based on sulphur combustion. The paper describes fluid bed technology and possible process concepts for decomposition plants. Additionally the thermodynamic background of the decomposition process and the main influence factors are provided to receive a better understanding of this technology.

Jan 1, 2009

By S. Schmachtel

Several possible physico-chemical properties of composite electrodes for oxygen evolution are presented to describe experimental data for which a mathematical model had been developed. On this basis, local electrical and electrochemical properties of a composite electrode were investigated with conductive atomic force microscopy (CAFM) and scanning electrochemical microscopy (SECM). It could be shown by CAFM measurement that the boundary between matrix and catalyst particles seemed to have special advantageous electrical properties. The SECM measurements showed the presence of mass transport phenomena with increased surface concentrations, whilst the thickness of the Nernst diffusion layer was very small. An intermediate was detected and assigned to be hydrogen peroxide. From all species involved in the oxygen evolution reaction (H2O2, H+ and O2), it was concluded that local active spots exist on the electrode on which hydrogen peroxide reacts to oxygen and protons. A two?step two-material process was suggested to explain the whole oxygen evolution mechanism.

Jan 1, 2008

By M. J. Little

Potgietersrust Platinums Ltd is Anglo Platinum?s only open pit operation and annually extracts 57 million tonnes of rock from 2 open pits. Over the past 3 years ~220 km of exploration drilling has been done, ~1000 km of rock face have been exposed for face mapping and over 7000 laboratory and field tests have been conducted. This has produced large amounts of geotechnical data to be utilised for feasibility studies, initial slope design and ongoing slope optimisation. It was necessary therefore to develop geotechnical databases to manage the vast amounts of data collected. SABLE and MineMapper 3D databases were created for logging and mapping respectively, with rock testing data incorporated into both. A pit inspections database was developed in MS Access and the existing groundwater and slope monitoring database was improved. The databases were linked to AutoCAD and Datamine to ensure that the latest geotechnical data is used for planning, draughting and modelling. The use of geotechnical databases ensures that no data is lost, standards are maintained and analysis can be easily performed. This increases the confidence of the analysis and allows the geotechnical engineers to optimise slope designs and blast designs on a regular basis. This reduces the risk of slope failure thus making the open pits more economical and safe.

Jan 1, 2006

By Y. Qin, L. Han, P. Gao, Y. Han, Y. Lia

In the present study, an innovative comminution technology of high-voltage pulse discharge was proposed for galena to weaken the mechanical property. The results of pre-treatment experiments indicated that the optimal operating conditions of spherical gap spacing 25 mm, pulse numbers 120, and loading voltage 25 kV were obtained, where the relative grindability of pretreated products was improved significantly, although with the prolonging of grinding time, the superiority of high-voltage electric pulses was gradually weakened. The galena ores were subjected to a high-voltage pulse discharge, and then the crack generating along the boundary between galena and gangue was observed under an optical microscope, and the surface burning which appeared in the ores. The scanning electron microscope (SEM) results indicated that the pretreated products were in a state of melting and then condensation, accompanied by some pore formation. Pulsed discharge pre-treatment not only produced more micro-cracks and cracks in the sample but also extended the original crack. Keywords: High-voltage pulse discharge; galena; relative grindability; micro-crack

Jan 1, 2020

By M. Rudolph, R. Tolosana-Delgado, G. van den Boogaart, M. Reuter, U. Peuker

This paper addresses the challenge to define a concept of entropy (state of order) for a textured particle system. Both the particle texture, the intergrowth respectively, and the particle size influence the order of a particle system. The smaller the particles become, the more particles form the solid system and the more permutations of the structure of the particle bed are possible. The texture within a particle is fixed, as long as it is not subjected to changes due to comminution, flocculation or agglomeration. The paper will present a definition of entropy, which is able to reflect qualitatively and quantitatively the intergrowth and the size (distribution) of the particles. Theoretical examples will show how different breakage mechanisms can be identified using the entropy definition. Furthermore, we will define the specifications for data sets to calculate the entropy of a particle system. Keywords: Milling, mineral liberation, intergrowth, statistical entropy, modelling

Jan 1, 2020

By A. A. Rogozhin, S. I. Anufrieva, A. V. Kurkov

The results of development of technologies for flotation concentration of two types of complex beryllium ores are presented: beryllium-fluorite in apocarbonate metasomatites (Type I) and rare-earthberyllium in feldspar metasomatites (Type II). The researched samples of Type I ores contain a mineral complex that is difficult to separate by fatty acid flotation, including phenakite, bertrandite, fluorite, and carbonate minerals. The ores are characterised by an increased content of fluorite and carbonates. The sample of Type II ore contains such rare-earth minerals as bastnesite and orthite, and a beryllium mineral - cleiophane. The size of individualised grains of cleiophane does not exceed 0.04 mm, which significantly limits the possibility of extracting the mineral into the enrichment concentrates. For the Type I ores, a technological process for the extraction of fluorite using a phosphorus-containing reagent from the class of dialkylphenyl polyethylene glycol esters of phosphoric acid (DAPEGEPhA) has been developed. The use of DAPEGEPhA enables the production of a high-grade fluorite concentrate (95% CaF2). The production of commodity phenakite-bertrandite high-grade (10% BeO) flotation concentrate from the fluorite flotation tailings with using a fatty acid collector is based on binding calcium in the flotation pulp using soda, sodium hydroxide and sodium tripolyphosphate. The use of a combined collector based on fatty acids and DAPEGEPhA made it possible to produce a collective rare-earthberyllium- lithium concentrate with high REE extraction (88%) from the Type II ores. The concentrates obtained are suitable for production of commercial-grade hydrometallurgy products. Keywords: Beryllium ores, flotation, reagents, concentrates, hydrometallurgy products

Jan 1, 2020

While some of the practical details of ilmenite smelting are not well documented, there is a substantial body of literature on the principles of ilmenite smelting, and the behaviour of solidified titania slag. This information is summarized, focusing on the basic reactions, departure from equilibrium, the behaviour of impurities, and reactions of solidified slag. The emphasis is on the South African operations.

Jan 1, 2007

By D. E. Kraushaar

Ruhrkohle in West Germany evaluates and compares the net present values of long-term periods from its coal mines by a computer assisted long-term planning system. Two main parts of this system are computer programs for the prediction of: (a) mineable reserves and their distribution in longwall panels as a function of dependent geological variables; (b) daily outputs and costs of longwall panels as a function of dependent geo- logical, layout and operational variables. This paper describes the investigations, which ended in the above computer programs: ? the collection of information from past workings and their organization in databases; ? the statistical evaluation of the databases, and ? the resulting correlation formulas. The correlation formulas vary the mean dependent variables as a function of independent variables which can be indicated with high reliability for planning projects in the long run. The system thus serves the purpose of facilitating long-term planning and excluding biased individual judgement of local planning staffs.

Jan 1, 1987

Copper cyanide is a common component of cyanide-treatable precious metal ores. The copper concentration in production heaps can be predicted from laboratory column tests, but the exact correlation is not necessarily intuitive. Generally, heap leach operators like to keep copper concentrations in solution below 300?500 ppm and may note problems with gold recovery and cyanide consumption when copper concentrations exceed this amount. There are several methods of copper removal from cyanide solutions including ion exchange; direct electrowinning; acidification, volatilization, and recovery (AVR); and sulphide precipitation such as the sulphidization, acidification, recycling, and thickening (SART) process. SART involves acidification with addition of soluble sulphide, separation of the resulting copper sulphide precipitate, and addition of lime to re-establish alkalinity prior to returning the solution to the leaching process, recovering both copper and cyanide as valuable products. In principle SART is very simple. Yet some SART plants that have been built may have been unnecessarily complex. This paper explores the basics of SART and makes the case for a simple plant design as applied to the heap leaching circuit.

Jan 1, 2012

By R. G. B. Pickering

The South African narrow reef hard rock mining industry has been stuck in a time warp with relatively little change in the mining process in the last century. This paper presents a methodology on how to implement change in narrow reef hard rock mining. It then explores a number of technologies that have been introduced into this mining industry and the impact that they have had on the mining process. The author then presents his view on whether the defined change process has been followed and sets out to identify the most critical aspect of ensuring that change is successfully implemented. Future demand will also be speculated on.

Jan 1, 2007

By J. Gholamnejad

Determination of the optimum cut-off grades is one of the most important aspects of mine production planning. A cut-off is a grade below which we choose not to process material. This material is treated as waste and dumped. Dumping waste is accompanied by the rehabilitation cost which will affect the overall cost of final production and also the optimum cut-off grade. Rehabilitation cost is the cost per ton of rehabilitating material of a particular type of rock after it has been dumped as waste. One of the most popular algorithms for determination of the optimum cut-off grade is Lane?s method. Lane formulated the cut-off grade optimization, but he did not consider rehabilitation cost during the optimization process. This cost item should be evaluated first, and then considered during the cut-off grade optimization process. In this paper the rehabilitation cost is inserted directly into the cut-off grade optimization process using Lane?s theory. The cut-off grades obtained using the suggested method will be more realistic than ones using the original form of Lane?s formulations.

Jan 1, 2009

By C. Botha

The South African democratically-elected government instituted policies and legislation that are intended to bring about change and transformation in the country and have drastically affected different industries, among others, the mining industry. The Mineral and Petroleum Resources Development Act 28 of 2002 (MPRDA) and the Broad-based Socio-economic Empowerment Charter (Mining Charter) were introduced in order to redress previous inequalities and to promote women's employment in the mining industry. This research evaluates the practical implementation of the MPRDA and the Mining Charter with specific reference to women in underground mining. A quantitative research paradigm was used. Data were collected through a process of a face-to-face interview surveys utilizing a structured questionnaire. The research setting was limited to the platinum-mining industry in the area of Rustenburg in the North West Province. The study population consisted of 195 available women working undergound at the mine. It is clear from the findings that mining companies are facing major challenges in their attempt to incorporate women in underground mining activities. Company policies regarding these issues must be firmly in place; however, the challenge lies in the translation of these policies into practice. In this regard, managers will have to play a leading role in the successful phasing in of women into the underground mining arena.

Jan 1, 2012