Search Documents

By P. Lenegan, R. Masethe, R. I. L. Ferreira

Underground mining in high rock-stress environments can induce unanticipated dynamic rockmass deformation, posing a serious risk to the workforce. Data collected by seismic networks are imperative for the design-as-you-mine process. Often an inappropriate assessment of the seismic hazard is done when unnecessary data are included in analytical techniques, particularly short-term time frames. Depending on the methodology or application of data analysis and interpretation, some of the information may not be relevant and even detract from the objective. By using the spatial event clusters associated with active workplaces to define the shape and size of the polygons for data selection for subsequent analysis, a problematic subjective component can be eliminated. The mining of tabular reefs in South Africa, be they gold- or platinum group metals, is very extensive, and underground workplaces are often widespread. Production stoppages are very costly, especially for marginal mines, so there is just cause not to evacuate an entire operation’s workforce following the occurrence of a large mining-induced seismic event. A rationale based on the damaging peak particle velocities (PPV) of the past seismicity can exclude the unaffected underground personnel and allow a quick orderly withdrawal where required. Micro-deformation may precede rockbursting, which can occur on-shift close to the workface. A mine-wide array of geophones suitable for the accurate location and analysis of seismicity may not be able to detect these higher-frequency emissions. Inexpensive but fit-for-purpose accelerometers, providing real-time, continuous measurement of acoustic rockmass deformation near the workplace, integrated through underground and surface communications networks, are shown to record ‘rock-talk’, clearly distinguishable from the instrument background noise, which can be in the order of hours leading up to an imminent damaging seismic event.

Jan 12, 2025

By C. C. Pretorius, S. Ramjee, R. J. Mostert

The study investigates the effect of prior corrosive exposure on crack growth resistance behaviour of thin sheet (3 mm thick) aluminium alloy 2024-T3 at slow strain rates. Compact tension specimens were exposed to standard corrosive environments that simulate accelerated atmospheric corrosion attack. Two corrosive environments were considered – an exfoliation corrosion (EXCO) solution and a 3.5 wt% sodium chloride solution. The unloading compliance R-curves of the two-hour EXCO-exposed specimens revealed a significant degradation of approximately 11% in the crack growth resistance behaviour (Kc_e values) compared to the baseline (air-exposed) values. Furthermore, secondary intergranular crack formation was also revealed in the plastic zone ahead of, and adjacent to, the crack tip of these specimens; which formed during the crack growth resistance loading. It is postulated that the observed degradation of the Kc_e values of the EXCO-exposed material is due to hydrogen embrittlement since the exposure times for the EXCO evaluation were limited to ensure that uniform corrosion dominated; that is, significant penetration of corrosion damage and pitting due to localized corrosive attack did not occur. The sodium chloride-exposed specimens revealed a similar degradation (13%) after 24 hours exposure. However, slight intergranular corrosive attack and isolated pitting were observed on the exposed surfaces prior to crack growth resistance loading, resulting in notch effects that could assist in crack growth. Pitting and intergranular corrosion were, however, not observed at the pre-crack tip. The relative contributions of the notch effects and the hydrogen embrittlement during the degradation of the KR performance are, therefore, unclear.

Apr 1, 2021

By O. A. Bascur

Ores are becoming extremely variable with mineralogy and hardness disturbing the grinding and flotation circuits. The current grinding and flotation sensors provide large amounts of data for process optimisation. Adding the right context and operational events augments operational knowledge for proactive actions to improve the performance of the grinding and flotation circuits. A data-driven strategy is needed to enable operations, maintenance, and business personnel to quickly and easily take corrective action when abnormal conditions occur. A digital plant template transforms data into operational insights in real-time. It uncovers the hidden, idle and downtime losses. By measuring and managing these unproductive times, people find new ways of avoiding them, improving the profitability of the plant. The information created by the real time analytics enables the calculation of recovery in real time and develops predictive analytics models to find the best operating condition based on the type of ore currently mined. The creation of new workflows and collaboration between mining and concentrator plant and the enterprise, including services providers, are enabled. A grade recovery model is used to identify the best operating conditions in real-time. An optimal Gaudin size distribution shape is used to find the grinding operating conditions that optimise the metal recovery in the rougher sections of the mineral processing plant. Sensors in the flotation circuits enable estimation of metal recovery and determine the optimal froth depth and aeration profiles, using an industrial air holdup flotation model. The implementation of a recovery/grind strategy with industrial examples in non-ferrous metal concentrator is presented in the paper. Keywords: Digital transformation, soft sensors, predictive analytics, grinding flotation optimisation, flotation bubbles, particle size, particle size distribution shape, froth aeration profiles, flotation air hold up model, recovery predictive analytics

Jan 1, 2020

By W. Newcomen, G. Dick

"Effective management and mitigation of pit slope instability in open pit mines begins with a comprehensive slope monitoring programme. The ability to differentiate between non-critical pit wall movements due to rebound or relaxation of the excavated slopes and movements that may be indicative of slope failure is important for maintaining a safe working environment and maximizing production. Slope failure prediction methods using velocity, acceleration, and strain criteria have been introduced and put into practice over the past few decades. Forty-eight slope failures with surface monitoring data are presented and assessed using the strain-based failure prediction approach, with consideration of the quality of the rock mass and the potential failure mechanism. The results indicate that the strain-based approach can be used to provide general guidance regarding strain thresholds for pit walls for a variety of failure modes in diverse geological environments. The advantages and potential drawbacks of the strain-based and other slope failure prediction methods are discussed. The importance of implementing a pit slope monitoring and performance evaluation system early in mine development is also emphasized. IntroductionThe successful prediction of the Manefay Slide pit slope failure at Bingham Canyon at 9:30 am on 10 April 2013 (Engineering and Mining Journal, 2014) highlighted the importance of having a comprehensive slope monitoring system that provides an accurate prediction of the time of failure of an open pit slope. Using most of the geotechnical monitoring tools available, the time of the failure was predicted within hours and equipment and personnel were evacuated from the pit well in advance of the failure. From a time to slope failure perspective, the monitoring system in place was a success.There are two general groups interested in monitoring pit walls, with slightly different objectives in mind when the monitoring system is being set up. There are those at the mine site that have to implement the pit slope design, monitoring protocols, and the action response plans, and there are those designing the slopes (often consultants) who regularly visit the mine but may not be responsible for the day-to-day activities. was a success.There are two general groups interested in monitoring pit walls, with slightly different objectives in mind when the monitoring system is being set up. There are those at the mine site that have to implement the pit slope design, monitoring protocols, and the action response plans, and there are those designing the slopes (often consultants) who regularly visit the mine but may not be responsible for the day-to-day activities."

Jan 1, 2016

By R. L. Machunda, A. M. Rugaika, D. D. Mdachi

Sedimentary and igneous rocks are the two primary sources of phosphate that are mined and beneficiated to fertilizer. During the beneficiation process, phosphate is lost into the tailings. We investigated phosphate concentrations in tailings dumps at Minjingu mine, Tanzania using energy-dispersive X-ray fluorescence spectrometry to quantify the chemical compositions. The phosphate content in the tailings varied from 12.91% phosphorus pentoxide (P2O5) in Tailings 2 to 19.61% in Tailings Dump 1. The naturally occurring phosphate concentration in rocks ranges from 3% to 35%, and phosphate tailings from various locations with P2O5 concentrations as low as 6.46-12.65% have been beneficiated to commercial fertilizer. Our investigation revealed that phosphate concentrations in Minjingu tailings may be sufficient to be recovered for commercial applications. Suitable recovery methods are discussed, and we recommend that beneficiation should be performed to minimize the loss of phosphate into tailings. Further research is needed to identify the optimal beneficiation methodology.

Aug 8, 2024

By N. Duda, W. Koperska, S. Anufriiev, P. Stefaniak

In mineral processing plants ore extracted from mines is processed to obtain a concentrate with the highest possible concentration of this valuable product. It is a complicated multi-stage process. Usually, the first step is sieving the ore, which is typically done using vibrating mining screens. There is often only a limited number of these machines in the technological chain, which is why their continuous operation, and proper maintenance is crucial for the whole process. Predictive maintenance is the best strategy in this case because it allows for minimising the number and duration of unexpected stoppages. It consists of the prediction of future failures based on available real-time data, and predictive models built upon this data using, for example, machine learning techniques. In this paper we concentrate on feature generation for future predictive maintenance model development for a vibrating screen, based on an example of a KGHM ore processing facility in Polkowice-Sieroszowice. We focus on two types of measurements: bearings temperature and vibrational data. Based on the raw data, the process of more advanced feature engineering is described. By transforming the temperature data we calculate characteristics of bearing cooling and heating dynamics, while based on vibrational data, the aggregated characteristics of the vibrations are derived. Such features are calculated on a long-term basis, and then they are compared to the data related to vibrating screen maintenance to estimate their significance for the prediction of particular failures of the machine.

Sep 1, 2021

By S. Govender, J. J. L. du Plessis, R. C. W. Webber-Youngman

Spontaneous combustion (SC) is a cold oxidation reaction that generates heat, causing a temperature rise of the reactant and leading, with limited heat dissipation, to self-ignition of the reactant, which occurs without an external heat source. Although not limited to coal, the most significant hazard of SC are the fires that occur in coal mining operations around the world. These fires pose a serious risk to the safety of workers in the mines as well as adverse effects on the environment, and can affect the quality of life for current and future generations. We investigated the occurrence of SC in raw coal storage bunkers with the purpose of compiling a decision analyser for engineers designing or working with coal storage bunkers. Specific experts were interviewed from different backgrounds and companies, followed by field research at a coal mine. The important factors affecting the possibility of SC occurring were the type of coal supplied to the bunker, the mining practice, and physical conditions around the bunker. The information presented here will assist in reducing the SC risk in raw coal storage bunkers. These findings, together with the systematic decision analyser developed, will assist design engineers and mine personnel to take early preventative steps in managing SC. The decision analyser was tested for many different scenarios and gave good guidance on how to minimize and prevent SC in bunkers

May 1, 2021

By C. O. Aksoy, G. G. U. Aksoy, A. Fisne, I. Alagoz, E. Kaya

Coal produced in underground mines is transported to the surface by means of conveyor belts throughout long roadways. The combustion of belts puts a large number of employees at great risk. Underground collieries differ from other underground mines -due to the combustible nature of the product. The most prevalent cause of belt fires in underground coal mine is spontaneous combustion due to oxidation of the coal, which also enables the conveyor belt to burn over time. In 2014, a belt fire in an underground coal mine in Manisa-Soma, Turkey caused 301 fatalities. A study has been conducted on this accident for approximately 3 years, consisting of combustion tests in a purpose-built research gallery, comparison of the test results with mine records of the accident, and CFD modelling of the mine environment. The intensity of the fire was sufficient to redirect the air flow underground, causin large amounts of toxic gases to fill almost the entire mine in approximately 15 minutes. It is recommended that CFD analysis be used in planning emergency action strategies in underground mines.

Dec 13, 2023

By R. Weideman, M. Le Roux, F. B. Waanders, Q. P. Campbell, E. Fosso-Kankeu, D. Moyakhe

"*Paper written on project work carried out in partial fulfilment of B.Eng (Chemical Engineering) degreeSynopsisSpent coffee grounds were transformed into biochar using a hydrothermal method. Some of the biochar product was pre-treated through surfactant impregnation with sodium dodecyl sulphate (SDS) to enhance its adsorption capacity. The non-treated(NT) and pre-treated(PT) biochars were characterized using FTIR spectroscopy and SEM-EDS analyses, which revealed that the products had the potential for adsorption of heavy metals from solution and confirmed the successful impregnation of biochar with SDS surfactant. The two adsorbents were then used for the removal of cadmium from solution and the adsorption behavior and capacity determined through adsorption isotherm, kinetic, and thermodynamic studies. It was found that the cadmium was adsorbed in several concentric layers on the surface of the adsorbents through a chemisorption mechanism. The PT biochar was identified as a superior adsorbent, with a capacity of qe = 10.67 mg/g compared to the NT biochar with qe = 4.82 mg/g. The adsorption of cadmium onto the PT biochar was further determined to be spontaneous and endothermic. It was therefore concluded that the PT biochar shows potential as an adsorbent and could be considered for implementation in the treatment of metal-polluted effluents. IntroductionCoal mining operations are notorious for producing large amounts of waste tailings, which are disposed of in the form of a slurry on tailings dams. This inadvertently contributes towards environmental problems (Jin, Mansour, and Thomas, 2017). Heavy metals are one of the most common pollutants that originate from solid mine waste disposal facilities, and these can leach into groundwater supplies, contaminating them and rendering the water unsuited for human consumption (Salomons, 1995). Cadmium occurs in conjunction with metalliferous ores and can cause severe damage to agricultural soils and drinking water supplies in the vicinity of mining sites (Dudka et al., 1995). It has a tendency to migrate into the surrounding vegetation, which in turn can cause harm to humans and animals when consumed (Marquez et al., 2018)."

Jul 1, 2019

By A. K. Raji, M. O. Ojumu

Robotic subsea dredging crawlers are dynamically and remotely controlled vehicles that are used for deep sea mining and recovery operations. These exploration machines are released from a mother ship and move around on the ocean floor using tracks. Current ocean crawlers such as the MK3 ROST are hydraulically powered. In this paper we develop a scaled-down model for simulating and performing static loading analysis of an electrically powered robotic subsea dredging crawler (EPRSDC). The modeling, simulation, and analysis were carried out using modelling software from Solidworks. The structural frame was assembled using the Tetrix max robotics kit. The kit’s structural components were produced from 1050 aircraft-grade aluminum. The results were used in optimizing and for considering other materials, and the to identify specific areas to be reinforced in future crawler designs.

Oct 3, 2023

By P. Goosen, A. Paterson, E. Paulsen

Ticor South Africa is currently involved in the mining and processing of a heavy mineral oredeposit at Hillendale Mine on the KwaZulu-Natal north coast. The orebody is characterized by a high ultra fine fraction (-45µm) that has a variable rheological behaviour when subjected to shear and hydration. Experience at Hillendale has shown that the ultra fine mineral tailings are sensitive to shear history in terms of shear intensity and shear duration as well as hydration history. This phenomenon expresses itself right through the primary beneficiation process influencing the mineral separation, but is especially prevalent on the residue disposal i.e. slurry transport and deposition on the tailings impoundment. Tube viscometer test work was conducted on the flocculated fine tailings that indicated that there was a change in rheology as a result of shear. This paper presents the results of the on-site test work conducted at the mine to measure the rheology at various stages in the process.

Jan 1, 2003

By C. J. Badenhorst

Oxides of sulphur are corrosive and are produced when sulphur-containing fuels are burned. Sulphur dioxide (SO2) is a colourless gas with a characteristic, irritating, pungent odour. Exposure routes to the human body are mainly through inhalation and skin and/or eye contact. Symptoms of exposure to SO2 may include irritation of the eyes, nose, and throat; rhinorrhea (discharge of thin nasal mucous); choking; cough; and reflex bronchoconstriction. To protect employees against the ill health effects of SO2 exposure, they are often required to make use of respiratory protection whenever entering areas were the SO2 levels exceed the statutory limits. The use of respiratory protective equipment should always be a last resort and should be considered only after other control measures have failed to reduce occupational exposure levels to below the occupational exposure limit or whilst other control measures are being investigated or implemented. Whenever the use of respiratory protection equipment is considered, it should always be used as part of a comprehensive respiratory protection plan. It is also extremely important that all potentially exposed persons are adequately and comprehensively informed and trained.

Jan 1, 2007

By J. M. Ortiz

This paper shows the usefulness of geostatistical conditional simulation combined with the quantification of sampling errors obtained from the analyses of fundamental errors ? validated from duplicate data ? to assess the relevance of the quality and quantity of the information, for short-term mine planning purposes. Traditional blast-hole drilling equipment has been designed for efficient drilling, but not for obtaining high-quality samples. Furthermore, blast-hole sampling interferes with production, and thus usually produces poor-quality results. These results are the basis of short-term plans, where the grades of selective mining units are estimated and used for distinguishing between ore and waste. Under these conditions, misclassification (ore blocks sent to the waste dump and waste blocks processed at the plant) is inevitable, leading to significant hidden losses that can amount to millions of dollars per annum. Reverse circulation drilling with the latest automated sampling technology improves significantly the quality of the information used for short-term planning, and thus reduces misclassification, improving the financial returns of the operation. In this paper, we present the general methodology for assessing the effect of poor blast-hole sampling, as compared to advanced reverse circulation drilling grids at several spacings, in order to arrive at the most appropriate grid for short-term planning. This plan can be prepared well in advance using several additional variables that are usually not available when the plan is based on blast-hole samples. Furthermore, blending options can be analysed in order to optimize plant recovery, minimize the use of sulphuric acid, etc. Three case studies are presented, namely a typical porphyry copper deposit, an exotic oxide copper deposit, and a complex gold deposit, where mineralization is controlled by structures and lithology. This paper shows that in all cases, advanced reverse circulation drilling grids provide good-quality information that, coupled with the use of geostatistics for short-term mine planning, significantly improve the financial returns of the operation.

Jan 1, 2014

By J. A. Kinnaird, B. J. Youlton, K. L. Youlton

Methods for treating and processing refractory gold ores are well established. However, what is less well understood is how the formation of the gold-bearing deposits affects gold processing and extraction. In order to evaluate the effect of ore genesis on gold extraction a number of South African gold deposits were studied. These included complex Pilgrim’s Rest samples as well as refractory Fairview, Barbrook, and Consolidated Murchison samples. We found the refractory nature of gold ores is controlled by a limited number of well-understood mineralogical factors. Solid solution gold is linked to low temperature and pressure conditions in fine-grained sedimentary lithologies, while reactive pyrrhotite can form from hydrothermal fluids associated with mafic magmatic rocks. These formational controls can be used to identify and avoid complex deposits at a desktop study phase, or address and reduce complications further along the pipeline using early mineralogical studies.

Jun 1, 2021

[Ferro Alloys Producers Association The South Africa Institute of Mining and Metallurgy www.saimm.co.za Mintek www.mintek.co.za Eskom www.eskom.co.za ]

Jan 1, 2004

The Gordonsville Operation of Pasminco US Inc. along with the Center for Advanced Mineral and Metallurgical Processing (CAMP) at Montana Tech studied, developed and implemented a pilot-scale hydrometallurgical facility for the industrial recovery of germanium and gallium. This paper describes the joint testing and engineering programme that culminated in this successful process.

Jan 1, 2008

By N. J. Wagner, D. G. Modiba

There is currently limited knowledge concerning South African coal deposits as hosts for rare earth elements (REE). This project aims to determine the concentration of REE, including yttrium and scandium (REY+Sc) in various coal seams and adjacent sediments in borehole cores from the Ermelo, Witbank, and Waterberg coalfields in South Africa. Coal petrography (maceral count and vitrinite reflectance), XRD, XRF, sequential chemical extraction procedure (SCEP) before ICPMS, and mineral liberation analysis (MLA) were conducted on the coal and associated sediment samples. The coals were inertinite-rich, medium-rank bituminous coal, with moderate to high ash content. The two dominant minerals in all the coalfields are kaolinite and quartz, except for sample ZBS2M, where dolomite was dominant. The dominant major oxides are Al2O3, SiO2, Fe2O3, and CaO, which concur with the XRD results. The ICP-MS results following SCEP indicated that both coal and the associated sediments were light REY+Sc dominant. There was also an elevation of medium REY+Sc in the Witbank coal’s associated sediment samples. Notably, the samples with the highest REY+Sc results were the sediment samples. The Waterberg samples had the lowest REY+Sc from both the coal (less than 2 μg/g to 7 μg/g) and associated sediments (2 μg/g to 15 μg/g). While the highest REY+Sc was yielded from the Witbank-associated sediments (500 μg/g to 2,500 μg/g). The carbonate fraction step proved to be the most successful leaching step, as most REY+Sc was recovered in that step for all coalfields. In addition to the carbonate fraction, the silicates and sulfide fraction in the Witbank samples, and the ion-exchangeable fraction for the Waterbergassociated sediments samples proved successful in leaching out the REY+Sc. MLA determined that monazite and xenotime in all the coal samples were the REY+Sc-bearing minerals.

Nov 6, 2024

By R. Thomason

Thank you Dr Barcza, President of the South African Institute of Mining and Metallurgy, for inviting me to share our experiences in Australia as regards the competency movement and my Association?s experience in assisting engineers become managers. This is my second visit to South Africa, and I am struck by the similarities between our countries. This extends to the professional issues associated with engineering and competencies in particular. I propose to outline two exciting stories today. ? Development of competency standards for professional engineers in Australia. ? Development of a management programme which has assisted professional engineers regain positions of leadership in Australian industry and government. First of all I would like to outline the Association of Professional Engineers, Scientists and Managers, Australia(APESMA).

Jan 1, 1997

By M. Nyoka

Historically bauxite-based refractories have been used in applications where andalusite-based refractories could work. Bauxite-based refractories were chosen over andalusite-based refractories mainly because of the availability of low-cost Chinese bauxite and also because many furnaces were designed by international companies that cannot easily access high-quality products. Currently, the availability of low-cost bauxite is under threat as a result of high export duties and tariffs as well as restrictions on the amount of material that China allows to be exported. South Africa is a major producer of andalusite, and this guarantees stability with respect to both availability and price. Refractories based on andalusite have an added economic advantage over bauxite-based refractories in that unlike bauxite, which requires high-temperature calcination before use, andalusite is used in its raw state. This paper constitutes a literature study of the merits, both technical and economic, of using refractories based on andalusite compared to bauxite-based refractories. Keywords bauxite, andalusite, refractory, furnaces, calcination.

Aug 1, 2013

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk, T. Punt

Recycling has become an important part of the lithium-ion battery (LIB) life cycle due to the growing demand for energy storage in applications like electric vehicles and renewable energy. Recycling spent LIBs provides a secondary source for strategically scarce metals, like lithium and cobalt, helping to reduce the environmental impact of LIBs. Organic acids have been proven to be effective lixiviants with the benefit of reduced environmental impacts, amongst which citric acid has shown to exhibit similar extraction performance when compared to mineral acids. Leaching LCO and NMC batteries with 1.5M citric acid and 2 vol.% H2O2 at 95°C, 20 g/L for 20 minutes achieved 93% Al, 90% Co, 96% Li, 94% Mn and 94% Ni dissolution. The strong chelating property of citric acid affects the separation of the metals, providing unique extraction opportunities. The first extraction uses 12 vol.% D2EHPA at a pH of 2.5 and O/A ratio of 2 to separate 96.4% Mn and 100% Al from the PLS in two counter-current stages. Stripping the loaded organic with 1.25M citric acid at an A/O ratio of 3 allows for up to 91% stripping of the manganese in a single stage. The second extraction then separates 96.5% Li from the PLS in three counter-current stages using 20 vol.% D2EHPA at a pH 5.5 and O/A ratio of 5. The raffinate remaining after the second separation contains 48.4 wt.% Co and 50.3 wt.% Ni. Keywords: Hydrometallurgy, lithium-ion batteries, metal recycling, citric acid, solvent extraction

Jan 1, 2020