Search Documents

The Skorpion Zinc Project demonstrated the viability of the production of zinc from non-sulphide (commonly called ?zinc-oxide?) ores, using the leach/solvent extraction/electrowinning process route. The success of Skorpion raised the profile of a number of other zinc oxide deposits, considered to be similar. However, a study of three such deposits demonstrates that the application of whole-ore-leaching may be limited and that the concentration of zinc, or at least the separation from acid-consuming gangue minerals, prior to leaching is essential to the successful recovery of zinc from these deposits. The recovery of zinc is dependent on an understanding of the geology of the deposit, the mineralogical association of zinc minerals with gangue minerals (Boni, 2005) and limitations of mining practice. Flow sheet development and the associated metallurgical test work to derive an economically viable treatment route from two of these deposits are discussed. Key parameters affecting zinc recovery by gravity separation and flotation are presented, demonstrating that even minor differences in mineralogy have a profound impact on zinc recovery and reagent consumption. The study also deals with the determination of appropriate design parameters through metallurgical mapping of the dense media separation process.

Jan 1, 2008

By W. Barthel, B. A. Dippenaar, J. Malan

In its most basic form, the process of sintering is very simple, and has been in use since the turn of the previous century. However, while the basic process is simple, control of the process relies on a number of extremely complex interdependent process parameters and requires a thorough understanding of the effect of these parameters on production capacity and product quality. Further, as with many other processes, the process parameters and hence design details of visually similar installations are highly dependant on the specific feed materials. While the industry trend has been towards an increase of capacity in order to lower unit production cost, typically in Iron ore sintering plants, this approach is not always possible for other commodities because of the scale of operation. This paper seeks firstly to describe some design considerations of sinter plants; secondly, to report on results from testwork performed with a specific series Manganese ore blends; and last, to relate these results to the design of new small-scale Manganese ore sinter plants.

Jan 1, 2004

By K. Kotwica, P. Gospodarczyk, J. Sosnica, J. Pawlik, Z. Iwulski, K. Pawlik

The paper presents problems resulting from the mobile mining machines functioning and requirements concerning a machine control system, which controls successive operation stages of such machines. The problem is presenting on the example of a mobile hydraulic support to remove residual pillars in copper ore mines. The paper describes an algorithm and a flow chart to be followed when designing a supports control system. Design of control systems to ensure machine function under given circumstances is also presented.

Jan 1, 2003

By W. Guiye, L. Chongjun, L. Huinan, Z. Yangge, H. Long

The current application of copper-molybdenum (Cu-Mo) separation inhibitors is often associated with large dosage, high toxicity, environmental pollution problems. In order to solve these problems, a light sensitive Cu-Mo separation inhibitor LS（light sensitive inhibitor，abbreviated to LS） was developed. In this paper, inhibitory performance, photodegradation rule, and acting mechanism of LS were studied. The subsequent test results showed that, compared with traditional inhibitors, LS has shown comparative advantages, with lower dosage and good inhibiting effect. A series of flotation tests with LS as inhibitor were conducted on a Cu-Mo concentrate. A locked-cycle test showed that a molybdenum concentrate containing Mo 49.88% and Cu 0.6%, with 93.23% molybdenum recovery and a copper concentrate containing Cu 29.92%, with 99.99% copper recovery can be obtained. The photodegradation performance of the reagent was investigated under 365 nm, 254 nm and sunlight irradiation. The degradation of the reagents could be completely achieved by irradiation of three wavelengths of light. However, with the different wavelength of irradiation light, the degradation rate is different, the time required to reach 50% degradation rate being 3 h (254nm), 4 h (solar light) and 6 h (365nm) respectively. The inhibition mechanism on chalcopyrite was studied. FTIR study showed that LS could be adsorbed on the surface of chalcopyrite by chemical adsorption, which could enhance the hydrophilicity of chalcopyrite. Ultraviolet adsorption tests indicated that the adsorption capacity of LS on chalcopyrite surface was greatly affected by pulp pH value, and the proper pH value was 5-9. Keywords: Copper-molybdenum separation, Inhibitor, Light-sensitive, Photodegradation, Mechanism.

Jan 1, 2020

By K. Yathavan

Fracturing of rock at low stress levels can be a source of unexpected problems in rock engineering: • the resulting instability can be a safety hazard; • in very brittle rocks it may be associated with violent failure of the rock and strainbursting (rockbursting); • it usually leads to an unexpected requirement for rock support, with time and cost implications; • in rock boring projects, it may result in fracture of the rock ahead of the bored face and in the walls of the bore behind the face. This may lead to cutter head vibration, increased cutter wear and consequently decreased performance and increased costs. Examples of situations in which fracturing of rock at very low stress levels has been observed will be described. This will include details or estimates of the in situ stress magnitudes and the rock strengths involved. La brisure de roche sous faibles contraintes peut être l’origine de problèmes inattendus en génie minier : • L’instabilité résultante peut devenir un danger • Elle peut provoquer des éclatements violents des roches fragiles • Elle nécessite souvent une infrastructure de soutien de la roche, ayant des implications sur les coûts et les délais • Les forages de la roche peuvent provoquer une brisure de celle-ci au niveau de la surface forée mais ainsi à l’intérieur de la roche, causant parfois des vibrations et une fatigue de la tête de forage, induisant une baisse de performance et un accroissement des coûts. Nous avons décrit ci-après des exemples de situations de brisure de roche sous faibles contraintes. Cette description comprend des détails ou des estimations des forces et des contraintes impliquées. Cette étude représente la base du travail de recherche effectué sur le phénomène. ißbildung im Gestein unter niedrigen Stressbedingung kann eine mögliche Ursache sein für unerwartet auftretende Probleme in der Felsmechaniklehre: • Die resultierende Instabilität stellt ein mögliches Sicherheitsrisiko dar; • In sehr sprödem Gestein kann es verbunden sein mit einem plötzlichen und gewaltsamen Zerfall des Gesteins; • In den meisten Fällen ist eine nicht eingeplante Gesteinsabstützung erforderlich, und damit ein Zeit- und Kostenaufwand verbunden; • Bei Bohrungsprojekten kann es dazu führen, daß es während des Bohrvorganges zu einer Rißbildung im Gestein hinter und vor der gebohrten Felswand kommt. Dies kann Bohrkopfvibrationen, eine erhöhte Bohrkopfabnutzung und folglich eine Bohrleistungssenkung, sowie Kostenerhöhung zur Folge haben. Das Phenomen von Gesteinsrißbildung unter niedrigen Stressbedingung wird anhand von einigen dokumentierten Beispielen erörtert. Diese beinhalten zudem Details oder Schätzungen bezüglich der Stärke des in situ Stressfeldes, sowie der gegebenen Gesteinsstärken. Die mit diesem Beitrag dokumentierten Ergebnisse formen eine Grundlage zur weiteren Forschung dieses Phenomens.

Jan 1, 2003

By J. -C. Tricket, W. A. Düweke, S. Kock

The high-resolution three-dimensional (3-D) seismic reflection data acquired for Impala Platinum between 1998 and 2002 in the western Bushveld Igneous Complex form an integral part of Impala?s mine planning and development programme. These data are of sufficiently high quality to provide unprecedented 3-D models of the geological structure of the Merensky Reef and UG2Chromitite Reef, from which the mine deduces the size, geometry and distribution of mineable blocks. Conversely, the seismic data details zones of un-mineable ground caused by structural disturbances in the form of potholes, fault zones and pegmatoid intrusions. Furthermore, variations in dip and strike are well imaged, allowing the mine planners to optimize the mine design and layout. Current interpretation work is focused on enhancing the accuracy of these geological model seven further through the analysis of ?seismic trace attributes.? Preliminary testing on the Impala Platinum 3-D seismic volume has shown that attribute analysis has the potential to illuminate a number of geological reef disturbances that are otherwise ?invisible? in the original seismic time volume. Potential areas of improvement include inter alia: ?Improved definition of major fault zones ?Improved definition of zones of reef depression (?slumping?) ?Identification of reef terracing and/or reverse dip.. Keywords: 3D reflection seismics; Impala Platinum Ltd; seismic attribute analysis; Seismic Micro Technology (SMT); rock solid attributes; dip-azimuth; instantaneous phase and similarity.

Jan 1, 2004

By F. Bonnet, J. Lehmann, H. Gaye

A review of thermodynamic information and models of slags, including associated software when available, is presented. The pertinence and accuracy of these models is discussed by comparison of their predictions for various slag thermodynamic properties with the available experimental data. Practical industrial applications will be illustrated by a literature review of the dephosphorization process of ferromanganese alloys and by the description of Ti behavior during silico-manganese alloys production. This latter example will show how the thermodynamic models have been used to propose a flotation treatment at low temperature to enhance TiC removal.

Jan 1, 2004

By O. I. Rychkova, M. N. Sycheva, E. V. Poryadochnova, G. V. Sedelnikova

Deposits of copper-porphyry type occupy a leading position in the mineral resource base of the world copper industry. They are characterized by large and gigantic scales, often complex composition, their development is carried out in an open way. The raw material base of the Russian copper industry is mainly sulfide copper-Nickel and copper-pyrite ores. Exploration of copper-porphyry deposits and the creation of long-term large mining facilities on their basis is one of the most promising and priority tasks for the Russian industry. This task is especially acute for the copper enterprises of the Urals in connection with the depletion of copper - pyrite ore reserves. In recent years, Russia has carried out a large complex of studies on the composition and technology of processing of copper-porphyry ores of different subtypes. In this work the complex poor copper-molybdenum-gold ore of one of the deposits is investigated. The chemical and mineral composition of the ore containing 0.49% copper, 0.020% molybdenum, 0.39 g/t gold, 5.85 g/t silver was determined. The forms of finding metals and their distribution by size classes are established. The dependence of extraction of metals into concentrates of collective-selective flotation on the size of ore grinding, pH of the medium, reagent consumption is shown. Under optimal flotation conditions, copper concentrate with 18.6% copper content and 92.32% extraction and molybdenum concentrate with 21.5% molybdenum content and 73.4% extraction were obtained. With a high concentration of molybdenum in selective flotation products, it is possible to conclude about the expected molybdenum concentrate with a content of 45% and a recovery of 70%. The associated extraction of gold and silver into copper concentrate is 76.8 % and 73.4%. Keywords: Collective-selective flotation, copper, molybdenum, porphyry ore, grinding, pH, reagents

Jan 1, 2020

Mineral Resource Throughput Management is based on the extraction of the maximum potential value from an ore reserve with the emphasis to generate maximum ROI and ROR (return on reserve). A steel producing company in India implemented MRTM to significantly improve their ROI and ROR. The value chain of this company consists of their own iron ore and coal mines, ore washing plants, sinter plants, steel plants, and sales and marketing division. The target for the mines was to produce at a stable and predictable rate and at specific quality requirements. These requirements were set to improve productivity and ROI of the steel plant. The implementation constituted the alignment of the reserve potential, total production chain, human resources and management culture at the mines with the requirements of the steel plant. Many typical mining practices were challenged and changed. Production targets regarding lump vs. fines ratio, consistent product tons, quality targets such as Fe, Al content and moist, and standard deviation on the quality targets were not achieved. A reverse distribution model with release mechanisms to satisfy the demand were developed and implemented at the mines. A stable and predictable flow of mine product with quality standards well within the required standard deviation targets were achieved. The contribution from the mines to significantly improve the Net Profit, ROI and ROR of the company were reached.

Jan 1, 2007

By J. N. Van der Merwe

Due to the approaching depletion of reserves in the Witbank Coalfield, and the fact that the Waterberg Coalfield is as yet under developed, there is increasing pressure to extend the lives of the operating coal mines in the Witbank Coalfield. One potential source of coal is the old pillars, often small and at shallow depth, that were not left with secondary extraction in mind. At face value, some of these pillars appear to be suitable for secondary mining due to their high safety factors. However, it is known that over time, these pillars have scaled and the current sizes are smaller than the as-mined dimensions. It is also known that at shallow depth, the overburden is often less likely to fail during secondary mining, resulting in high abutment loads on the unmined pillars. The paper proposes a systematic method to pre-evaluate those old pillars for the possibility of stooping. The method consists of elements of fundamental methods and newly developed technology. In essence, it revolves around using empirical methods to estimate current pillar dimensions, followed by numerical modelling to investigate the probability of progressive pillar failure and then fundamental methods to determine the limits of applicability of the numerical model.

Jan 1, 2012

By T. Nishi, D. Teguri, K. Saitoh

In recent years the requirement for high carbon ferro-manganese (HCFeMn), which is the key product of our company, has increased due to bullish demand for steel products. In our Tokushima works, we have 2 closed types of electric furnaces (1F and 2F), with which we are manufacturing HCFeMn. In order to meet the increase in demand, we made various modifications to these furnaces and we tried to increase the furnace operating loads. Especially for 1F, we deepened the furnace. In this paper, we report the results of this modification. The operational situations of the above-mentioned two furnaces are different because they have different individual profiles. As for 1F prior to modification, the depth of the furnace was one meter shallower than2F, because 1F was designed for the manufacturing of SiMn. On the other hand, our Tokushima works specialized in HCFeMn 14 years ago. However, the profile of 1F was not optimized for HCFeMn. In comparison to 2F, 1F was more difficult to stabilize due to the smaller tolerance for the adjustment of the electrode length, the metal / slag level, and the coke-mixing ratio. We deepened 1F by 770mm by disposing of the furnace rolling mechanism. We consequently achieved a 10% increase in production capacity. This meant the operating load was enhanced from 24.5MW to 27MW, the furnace became more stable and the tapping speed of both metal and slag increased, all which made the tapping easier than before.

Jan 1, 2007

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the ?fine? and ?coarse? size classes appear to be diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favours a different flotation environment. An improvement in the flotation kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferentially recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: ? Standard flotation machines (standard energy input, rotor speed (r/min), rotor size/type) at the beginning of the row, where flotation is typically froth-phase limited and operational and set-up parameters have a limited influence on the recovery ? Higher-powered flotation machines (high rotor speed, high-power rotor size/type) at the end of the row to improve fine particle recovery ? Lower-powered flotation machines (low rotor speed, low power rotor size/type) to enhance coarse particle recovery. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for ?fine? and ?coarse? particles are predicted for both forced-air and naturally aspirated machines. The greater predominance of UG2 ore types, coupled with the skewed feed distribution of platinum group metals (PGMs) to the finer size fractions, suggests that PGM flotation circuits are not designed for optimal recovery across the size distribution. The application of the hybrid energy concept to PGM flotation offers a possible shift towards a more efficient flotation circuit solution through a managed distribution of energy.

Jan 1, 2012

By M. Mokgohloa, T. R. Stacey

Boring of tunnels and shafts in hard rock under high stress conditions is becoming more common as mines and tunnels are developed at greater depths. Under the high stress conditions, fracturing of the often-brittle rock occurs in the walls, backs, and ahead of advancing faces of excavations. Fracturing can have a significant impact on boring activities: sidewall spalling, which affects machine gripper capacity, and fractures can also develop in the rock ahead of the face, leading to blocky rock conditions, which may have a significant effect on machine excavation. Fracturing may develop dynamically, leading to rock bursts manifesting in the form of strain bursts, which can be hazardous and destructive. In brittle rock, fracturing is commonly extensional in nature. The focus of this paper is on fracturing in the face of the excavation. Examples of such fracturing behaviour are described briefly in the paper. Numerical analyses were carried out to predict the initiation of extension fractures and their orientations ahead of excavation surfaces, and the resulting formation of rock slabs/plates, and the stability of these plates. The results should be beneficial for the evaluation of the conditions prior to, and during boring operations.

Nov 27, 2024

By Md. Amanullah

A novel triple action load cell assembly (LCA) was developed to determine three index parameters reflecting compressive, tensile and shear characteristics of mudcakes. The results indicate that the tensile, compressive and torsional behaviour of mudcakes are strongly influenced by the physics and chemistry of the mud additives. Eine neuartige dreifach wirkende Druckkammer zur Bestimmung der drei Indexparameter Druck, Zug, und Scherung von Spülungskuchen wurde entwickelt. Die Ergebnisse weisen auf einen starken Einfluss der physikalischen und chemischen Spülungszusätze auf Druck, Zug, Scherung hin. Un assemblage d'une nouvelle cellule a triple action (LCA) a été développée pour déterminer trois paramètres caractérisant la compression, la contrainte en traction et la résistance á la fracture des cakes. Les résultats indiquent que les comportements tensile, compressif et de torsion des argiles sont fortement influencés par la chimie et la physique des additifs des boues.

Jan 1, 2003

By C. J. Pretorius

More than 30 percent of the global demand for zircon (ZrSi04) is supplied by South Africa. A significant amount of the zircon is exported, and beneficiated products are then imported for industrial applications locally. Beneficiating the zircon locally could have a positive impact on the local market, since zircon is only one of many such cases. Ammonium acid fluoride serves as an alternative anhydrous fluorinating agent for zircon in the synthesis of several metal fluorides1,2. It provides an effective dry fluorinating method and is easier to handle than hydrogen fluoride or fluorine gas. Zircon exposed to extreme plasma temperatures dissociates and becomes more reactive. The reaction of the plasma-dissociated zircon (Zr02.SiO2) with the ammonium acid fluoride (NH4F.XHF, where x= 1 to 5) forms two main intermediate compounds (NH4)3ZrFr(s) and (NH4) 2SiF6(s), the latter decomposing to form volatile products at relatively low temperatures, providing easy separation of the silicon and zirconium compounds. The ammonium zirconate compound decomposes to form zirconium tetrafluoride (ZrF4), which can be further manufactured into zirconium metal, to name but one product. Data on the kinetics of the reaction of ammonium acid fluoride with zircon and plasma-dissociated zircon, combined with the thermo¬dynamic parameters of the reaction, is essential for the development of an industrial process for the production of a precursor for the manufacturing of zirconium metal, namely anhydrous ZrF4. Both the reaction kinetics and reaction parameters will be included in this study, as well as some proof that the reaction proceeds to ZrF4 on a small batch scale. If the exact reaction parameters can be pinned down, a wide spectrum of anhydrous metal fluorides can be synthesized through this fluorination route.

Jan 1, 2012

By А. V. Aksenov, S. G. Rybkin, А. Y. Senchenko

For gold plants in Russia, it is very complicated and costly to use cyanide leaching for efficient processing of gold refractory ores, where gold is closely associated with sulphide minerals and the significant amount of natural carbonaceous matter present. Oxidative roasting of gold refractory concentrates is a well-known method, making it possible to obtain a high recovery rate of precious metals to a target product. The use of oxidative roasting is limited in general by the expense of capturing and neutralising the harmful components of roasted gas, mainly sulphur (SO2, SO3) and arsenic (As2O3) oxides. This paper addresses testing and development of an optimised technology to process gold refractory gravity and flotation concentrates by means of oxidative roasting which stabilises arsenic as calcium arsenate. The process involves roasting of a gravity or flotation refractory ore concentrate in a mixture with lime and calcium chloride, with a supply of oxygen, and at 600-700°С. During the roasting a carbonaceous matter of the concentrate burns out and sulphide components transform into harmless calcium sulphate (CaSO4) and calcium arsenate (Ca3(AsO4)2), and iron passes into the form of hematite (Fe2O3). After disintegration, the roasting cinder is concentrated on a table to obtain a high-grade gravity concentrate and gravity tailings. The high-grade gravity concentrate is subject to smelting in a mixture with fluxing agents, which results in alloyed gold and slag. The gravity tailings are ground and reported to cyanide leaching. In the case of a flotation concentrate, the roast cinder is ground to minus 30 μm and subject to sorption cyanide leaching. High gold recovery (90-95%) of the target product and environmental safety are typical of the improved technology under consideration. Two national patents were granted for the methods developed to treat refractory concentrates bearing precious metals. Keywords: Gold concentrates, oxidative roasting, cinder, cyanide leaching, smelting, alloyed gold

Jan 1, 2020

By D. Mkhwanazi

The purpose of the project was to optimize load haul dump (LHD) machinery use as they were spending too much time doing what they should not be doing. During the investigation, the author found that the machine's actual availability was 86% and the utilization ranged between 30% and 42%. This shows that the availability of the machine has met its target. Therefore the main problem was with the LHD utilization and that is what the project focuses on. To satisfy the objectives, the author firstly studied the existing mining data like the key performance indicators (KPIs) in order to analyse the machine's availability and utilization; this is what gave direction to the problem. Secondly the author did a literature review on mines with similar problems. This gave the author ideas on what to look at in approaching such a situation. Thirdly, the author gathered information on what the LHDs are doing on a daily basis by doing a time study. This gave the author an idea of how long it took the LHDs to complete a specific task. The author also interviewed operators and their supervisors in order to find the best practice work. This helped in identifying the problem areas when comparing the best practice work with what the LHDs are actually doing. According to the project results, it was found that the LHDs are underutilized due to shortage of drivers and the long distances the LHDs have to travel for material loading and refuelling. The author recommended that the machine utilization should be improved by training more operators in order to eliminate the 'no operator' downtime; the cost arrangement of this recommendation is included in the report. The author also recommended that the travelling time should be reduced by using tractors instead of LHDs when long distances need to be travelled for material loading. Another recommendation for reducing travelling time was to bring the mobile fuel tank closer to a section; the cost arrangement for this recommendation is also included in the report. Keywords Optimizing, LHD utilization, LHD availability, key performance indicators (KPI), shortage of drivers, long distances, mobile fuel tanks.

Jan 1, 2011

By J. W. Klokow, S. L. Mulder

Early removal of the shaft reef is usually considered necessary on deep level South African gold mines to avoid damaging stress build-up associated with traditional shaft-protection pillars. In the case of the relatively shallow Beatrix Gold Mine it was largely motivated by early access to ore and the consequent earlier return on invested capital. A number of options were considered to protect the shaft from possible damaging stress changes and to minimise deformations in the shaft-reef area. Numerical modelling was used to evaluate the options and to quantify as accurately as possible the likely deformations to be accommodated by the shaft steelwork designs. The option chosen was a combination of strategically placed satellite pillars and yield pillars, and backfill. Following the mining of a small inner cut during the shaft sinking process, full-scale mining is progressing away from the shaft. Suitable instrumentation has been installed to monitor deformations associated with the shaft reef removal. Enlever rapidement le filon du puits est en général considéré nécessaire dans les galeries de fond des mines d’or sud-africaines pour éviter l’accumulation nuisible de contraintes associée aux piliers de protection de puits traditionnels. Dans le cas de la mine d’or Beatrix, relativement peu profonde, l’enlèvement était motivé en grande partie par l’accès rapide au minerai et par conséquent un profit plus rapide sur l’investissement. Un certain nombre d’options furent considérées pour protéger le puits contre les changements de contraintes potentiellement nuisibles, et pour minimiser la déformation dans l’aire puits/filon. La modélisation numérique fut utilisée pour évaluer les options et pour quantifier aussi précisément que possible les déformations probables que la conceptualisation du puits devrait prendre en compte. L’option choisie fut une combinaison de piliers satellites placés à des points stratégiques avec des piliers de protection, et terre de remblayage. Pendant le fonçage de puits une petite coupure intérieure fut exploitée, et maintenant l’exploitation à grande échelle, au-delà du puits, est en cours. Les instruments nécessaires ont été installés pour surveiller les déformations associées à l’enlèvement du filon du puits. Die frühe Entfernung des Riffschachtes wird normalerweise bei südafrikanischen Tiefbaugoldmienen als notwendig erachtet um den zerstörende Druckaufbau zu vermeiden, welcher mit traditionellen Schachtschutzpfeilern verbunden ist. Im Fall der verhältnismäßig flachen Beatrix Goldmine war es hauptsächlich vom frühen Zugang zum Erz und dem konsequenten frühen Rückfluß des investierten Kapitals motiviert. Eine Anzahl an Optionen wurde erachtet um den Schacht vor möglichen zerstörenden Druckänderungen zu schützen und Deformationen im Riffschachtbereich zu minimieren. Um die Optionen zu bewerten und mögliche Deformationen so genau wie nur möglich quantitativ darzustellen die von den Schachtstahlkonstruktionen aufgenommen werden müssen, wurden numerische Modelle verwendet. Die gewählte Option war eine Kombination aus strategisch plazierten exzentrischen Pfeilern und Schutzpfeilern sowie Hinterfüllungen. Nach dem Vortrieb eines kleinen inneren Einbruches während des Abteufens wird der Vollvortrieb vom Schacht weg vorgenommen. Um die Deformationen, die mit der Riffschachtentfernung verbunden sind zu überwachen, müssen geeignete Instrumentenausrüstungen installiert werden.

Jan 1, 2003

By Swapan Ghosh, Amitava Sengupta, Proloy Das

Ferro-alloys are very important ingredients used for making of quality steel with desired composition. In view of high demand in various types of ferro-alloys, it has become necessary to produce the same efficiently, safely and cost-effectively with consistent quality maintaining the anti-pollution norms. To achieve this goal, it is necessary to adopt latest process/equipment with the state-of-the-art instrumentation and automation system. A Programmable Logic Controller (PLC) based automation system with suitable Human Machine Interface(HMI) terminals along with intelligent field mounted sensing/control devices allows to monitor and control the complete plant effectively with optimum deployment of man-power. In association with this, use of process optimization controllers enables to achieve specialised functionalities of the submerged arc furnaces like material management, lining management, electrode management, power management, overall production management etc.

Jan 1, 2007

By T. Phiri, Antoine Floribert Mulaba-Bafubiandi

Microwave energy has been recently used in minerals processing to speed up the leaching process or to improve the liberation of targeted minerals (Al-Harahshed and Kingman, (2003); Bradshaw et al., (2001)). Applied to the roasting of sulphide minerals, microwaves allow the ?tunning? of calcine types and products quality in addition to the energy savings as opposed to the conventional roasting (Mulaba, 2006). As more than 85% of world zinc is produced through the ?roast-leach-electrowin? route, an attempt was made to optimize cost, energy and product quality for metal extraction process route. The use of microwaves was the alternative process route selected for the optimisation. Pyrite concentrate (0.17% Zn, 0.09% Cu, 35.71% Fe, 43.76% S) and sphalerite concentrate containing 43.81% Zn, 0.37% Cu, 3.86% Fe and 44.39% S were microwave roasted in a multimode cavity of 2.45 GHz with varying power levels and for different durations. The produced calcines were characterized using AAS, XRF, XRD and Mossbauer spectroscopy while the determination of residual Sulphur was used as products quality control tool to ascertain the degree of roasting achieved on the feed. The leachability of the produced calcines in HCl, HNO3, H2SO4 and HNO3 + HCl has been studied in terms of the best leaching yield, process kinetics economics and environmental aspect. With 800 W power for 30 minutes, ZnO and Fe2O3 were formed corresponding to a 70% sulfur removed from sphalerite and 80% from pyrite concentrates respectively. While the roasting of the above concentrates appeared to be a first degree processes, it was noticed that the microwave assisted roasting of sphalerite and pyrite concentrates yielded lower sample surface temperature for a shorter time (i.e.less than 30 minutes) microwave exposition. Longer time (more than 30 minutes) microwave exposure showed a linear increase in temperature in function of power level used. While optimum roasting conditions were found at 800W, 30 minutes, a 10% increase of sulfur removal was noticed while pyrite concentrate was microwave roasted. Sulfuric acid was seen to give higher leaching yield than nitric acid. Zinc dissolution was hindered by the presence of franklinite.

Jan 1, 2007