Search Documents

Electrochemical measurements are presented on electro-deoxidation of silica in molten calcium chloride at 900°C, with porous silica pellets as starting material. Measurements during pre-electrolysis (to remove water from the melt) showed electrochemical noise, which is consistent with the evolution of hydrogen. Throughout, the dominant anodic reaction appears to be CO2formation, based on the observed potential at the anode, and measured anode wear. Because of the presence of dissolved CaO in the melt, some of the CO2 candissolve in the melt; the resulting calcium carbonate formation was confirmed by electrolyte analysis after reduction runs. Reduction of dissolved CO2 at the cathode is likely to contribute to the background current during the reduction process. For the electrode and cell configuration used here, most of the over potential arises from polarization of the anode, and ohmic potential drop in the electrolyte.

Jan 1, 2006

By A. R. Leach

Anomalous mining conditions can be described where the level of hazard is increased relative to normal conditions within a mining area. Normal conditions would be those defined as a Ground Control District in a mine’s code of practice, and for which mine standard support layouts are generally developed. It has been found that up to 80% of fall of ground accidents occur where anomalous mining conditions exists, typically in the vicinity of geological weaknesses. These areas require specific attention to ensure they are readily anticipated and identified and that appropriate strategies are used to reduce the hazards associated with them. As part of SIMRAC project GAP 607 checklists to aid identification and best practice mining methods were identified for a range of geotechnically anomalous conditions.

Jan 1, 2003

By D. F. Malan, J. C. Esterhuyse

In this study we explore the use of a novel numerical modelling approach to study the effect of pillar reinforcement on pillar stability. Case studies in the literature indicate that tendons, strapping of the pillars, and shotcrete or thin spray-on liners are commonly used to reinforce pillars. No clear methodology exists to select the type of support or to design the capacity of the support required, however. This has led to ongoing collapses in some mines in spite of heavy support being used to reinforce unstable pillars. A limit equilibrium model with confinement on the edge of the pillar was used to simulate the interaction of the support with the failing pillar. The model correctly predicts that an increase in confinement will lead to a decrease in the extent of pillar failure. As the displacement discontinuity boundary element method allows for the efficient solution of largescale bord-and-pillar layouts, the effect of pillar confinement can now be studied on a mine-wide scale. Accurate calibration of the limit equilibrium model is, however, required before this method can be used for the design of effective pillar support.

May 3, 2023

By J. N. Van der Merwe

The data base of failed pillar cases as used by Salamon and Munro (1967) in their original analysis to determine the strength of coal pillars empirically, has been updated for this study. It is shown that the Vaal Basin and Klip River coal fields exhibit similar behaviour that differs from the failures in other areas, i.e. failure at high safety factors within a short period of time. Those collapse cases have been omitted from the new data base. Failures in the other areas that occurred after 1967 have been added. Using a technique to minimize the area of overlap between the populations of safety factors of failed and intact pillar cases, the new data base was re-analysed in conjunction with the original Salamon-Munro data base of intact pillar cases, from which the cases in the areas of weak coal were likewise eliminated. It was found that a linear formula reduced the overlap area by22%. The new formula predicts higher strength for pillars with a width-to-height ratio greater than approximately 2.0 to 3.0 and a lower strength for smaller pillars. It was also found that in order to obtain the same relative measure of stability as with the Salamon-Munro formula, the strength constant in the new formula should be within a range of 2.8 to 3.5 MPa. For most current South African coal mining conditions, using the new formula for pillar strength will result in leaving smaller pillars without sacrificing stability. The reason for this is that the Salamon-Munro formula under-estimated the strength of larger pillars and over-estimated the strength of smaller pillars. The new formula will thus result in improved reserve utilization without sacrificing stability.

Jan 1, 2003

By S. E. Olsen, T. Færden, G. Tranell, T. Lindstad, J. Lubetsky

The authors are lead authors for chapter 4.3 ?Emissions from Ferroalloy Production? in ?2006 IPCC Guide-lines for National Greenhouse Gas Inventories, Volume 3?. The paper discusses the methods to calculate and report emissions from the production of ferrosilicon, silicon-metal, ferromanganese, silicomanganese and ferrochromium alloys, as well as the basis for the methods and choice of emission factors. CO2 is the main greenhouse gas emission from ferroalloy production, accounting for about 95 % of the total CO2-equivalents. The most accurate method of determining emissions is to base the calculations on reported amounts and analyses of reducing agents and carbonate ores used in the process. If analyses are not available, typical CO2 emission factors for the different reducing agents are recommended. If neither reliable amounts nor analyses of all reducing agents are known, default generic CO2 emission factors for the type of ferroalloy multiplied with amount produced, can be used. The CO2 produced from bio-carbon (charcoal and wood chips) should be reported but will not be accounted for in national emissions. If any bio-carbon is used, the default generic CO2 emission factors cannot be applied. CH4 accounts for less than 1 % of the total emission of CO2-equivalents. Default emissions factors for CH4 are given for the production in open or semi-closed furnaces of silicon-metal and ferrosilicon. In the production of FeMn, SiMn and FeCr in closed furnaces the gas containing CO,CO2 and volatiles can be combusted in boilers and N2O may be formed. While reporting is not required, IPCC Guidelines recommend that the N2O-content in the off-gas is measured.

Jan 1, 2007

By N. McEwan

Keywords: refractories, chromite, Marico This paper examines the role of refractory-grade chromite in refractories. The chromite deposit at Verref?s Marico Chrome mine is described. The refractory properties of chromite and their role in basic refractories are described. The properties and metallurgical applications of chrome-containing refractories are described and finally environmental issues associated with chrome-containing refractories are discussed.

Jan 1, 2011

By T. Nishimura, H. Kiyama, K. Wakimoto

Discussion on the load bearing capacity of ground and the stability of tunnel is presented. We derive a simplified solution of a circular lined-tunnel in an elastic ground. The solution results in a better understanding of characteristic curves. Use of DEM allows us to consider effects of possible yield of the overstressed zone around the tunnel and inherent discontinuity of ground on the curves. Diskussion auf der Last Tragfähigkeit Bodens und die Stabilität des Tunnels wird dargestellt. Wir leiten eine vereinfachte Lösung eines kreisförmigen Ausbautunnels in einem elastischen Boden ab. Die Lösung ergibt ein besseres Verständnis der Kennlinien. Um Gebrauch DEM erlaubt uns, zu betrachten Effekte des möglichen Ergebnisses der überbetonten Zone den Tunnel und zugehörige Unstimmigkeit des Bodens auf den Kurven. La discussion sur la portance de charge de la terre et de la stabilité du tunnel est présentée. Nous dérivons une solution simplifiée d'un revêtement-tunnel circulaire dans une terre élastique. La solution a comme conséquence une meilleure compréhension des courbes caractéristiques. L'utilisation de DEM nous permet de considérer des effets du rendement possible de la zone surchargée autour du tunnel et de la discontinuité inhérente de la terre sur les courbes.

Jan 1, 2003

By M. Kawakami, K. Suzuki, T. Takenaka, S. Yokoyama

Molten NaNO3-NaNO2-KNO3mixture is used as a heat transfer medium at high temperature. One of the most important properties of this mixture is the heat capacity. In the present work, the enthalpy change with temperature was measured by the drop calorimetric method to evaluate the heat capacity. The results are summarized as follows: The enthalpy of the mixture increased linearly with the temperature. From the slope of the line, the heat capacity was evaluated. The heat capacity of pure NaNO3, NaNO2and KNO3was 0.129,0.110 and 0.142 kJ/mol/K, respectively. These values are in fairly good agreement with the published data. In the binary and ternary systems, the molar additivity of heat capacity, which is well known as Neumann-Kopp’s law, was obtained. The heat capacity of HTS1and HTS2, which are well known ternary mixtures of practical use, were in the range of published data.

Jan 1, 2004

By Y. Jeong, K. Kim

Excess water can lead to instability and even failure in tailings storage facilities (TSFs). Simply reducing the amount of water in TSFs could be the best way to ensure the safety of nearby communities. In this case study we investigated the effects of reducing the water content in tailings slurry at a copper-cobalt-zinc mine in Mexico. An environmentally friendly polymer was used as a drag reduction agent (DRA) to offset the increase in solids percentage. The potential effects of the increased solids concentration on the tailings transportation system were also assessed. A series of ‘what if’ studies was conducted to assess whether adding the polymer would allow the solids concentration to be increased without changing the pressure loss in the tailings pipeline. The studies entailed conducting pipe loop tests to investigate these changes under various solids/ polymer concentrations and then constructing a computational fluid dynamics (CFD) simulation model using the test results. The validated model was used to determine the optimal polymer percentages needed to maintain the same pressure loss under baseline (30% solids) conditions, and to assess the potential risks (clogging, increased erosion rates) to the pipelines. The potential water savings were found to be significant, varying from about 1.852 Mm3/a at 35% solids to 3.915 Mm3/a at 45% solids.

Dec 13, 2023

By K. Moxham, R. G. B. Pickering

Over the last few years Lonmin Platinum and Sandvik have embarked on a unique partnership of collaboration through a systematic approach to developing equipment to mechanize and automate narrow reef platinum mining. After the initial design and manufacture of the equipment the key aspect is the integrating equipment, people and method into a mining system. Another key a spec of mechanization is the optimization of equipment utilization and this philosophy has ensured continual evolvement of mining methods. This paper describes the trials and development that have resulted in the mining method described as Lonmin mechanized breast.

Jan 1, 2006

By P. Rice, A. Photolo, A. C. Barnard

Introduction -Sampling Tool Project (STP) -History -Results to date -Costs -Questions

Jan 1, 2005

By S. W. Robertson, M. T. Golela, S. Mxinwa

South Africa has one of the largest Cr-related industries in the world and generates large amounts of Cr-containing smelter dusts. It is normal practice to scrub Cr from the furnace off-gas in water, and to recover the Cr by adsorption, followed by recycling of the loaded adsorbent into the furnace. A study was conducted to find a low-cost adsorbent that is capable of removing sufficient Cr from the solutions generated by scrubbing. The test work focused on the evaluation of different clay minerals (attapulgite, bentonite, and kaolinite) as adsorbents for Cr. Cr(VI) could only be adsorbed after prereduction with e.g. ascorbic acid (ASA). An 80% removal of Cr(VI) could be achieved from a solution containing 20 mg/L Cr using bentonite clay after reduction with ASA. Attapulgite and kaolinite adsorbed less than 55% Cr after reduction with ASA. Both ASA and ferrous salts were found to be suitable reducing agents. The use of acid mine drainage (AMD) was also investigated as a low-cost alternative reducing agent, as AMD usually contains iron. The Cr(VI) reduction potential of the AMD was determined by redox titration against a solution containing 50 mg/L Cr(VI). Studies show that AMD can potentially be used as a reducing agent in a Cr removal process if it is available on site.

Feb 12, 2024

By A. McLean, M. Iwase, K. Wakimoto, K. Katogi, Y. Kikuchi

One of the greatest obstacles to the application of physical chemistry principles to the elucidation of slag-metal reactions is a lack of knowledge of activities of the reacting species. To a large extent, oxygen potential of the slag phase governs iron and steelmaking practice. Without oxygen control by means of appropriate sensors, the behaviour of the other elements cannot be managed. In this paper, measurements of the FeO activity with various types of electrochemical FeO sensors will be described together with examples of their applications for improved strategies toward better practice for ladle metallurgy and sulphur and manganese distributions between slag and metal phases during steelmaking. Measurements of FeO activity have also been made in order to improve dephosphorization reactions. This type of work has led to significant reduction in volume of slag generated within the steelmaking vessel, which in turn has important implications for refractory wear, metal yield, alloy recovery and improved productivity. Finally, an on-line sensor is described that permits the oxygen potential to be determined for both the metal phase and the slag phase during steelmaking in the BOF.

Jan 1, 2004

By K. Sugawara, H. -S. Jeong, Y. Ishiguro, J. Otani, Y. Obara, A. Hirata

A series of measurements of induced stress by the Compact Conical-ended Borehole Overcoring (CCBO) technique was performed within rock mass around a tunnel excavated in a region that an underground powerhouse is constructed under high initial rock stress. In the measurements, a phenomenon of core disking was observed during overcoring. The selecting method of strain data uninfluenced by the core disking was proposed, using X-ray CT scanner. Then, the state of induced stress determined from the selected strain data was discussed, comparing with the state of initial stress. Eine Serie von Messungen von induzierter Belastung mit kompaktem konisch-beendetem Überbohrverfahren (CCBO) wurde in Felsmassen um einen Tunnel ausgeführt, der in einer Region gebohrt wurde wo ein unterirdisches Kraftwert unter hoher anfänglicher Felsbelastung gebaut wird. Bei den Messungen wurde beim Überbohrverfahren ein Phänomen des Core Disking beobachtet. Die gewählte Methode der Belastungsdaten, unbeeinflusst durch Core Disking wurde vorgeschlagen, unter Verwendung von Röntgen-CT-Scanner. Dann wurde der Zustand der induzierten Belastung aus den gewählten Belastungsdaten diskutiert, unter Vergleich mit der ursprünglichen Belastung. Une série de mesures de contrainte induite effectuée avec la technique de forage de sur-carottage compacte à embout conique a été exécutée dans la masse rocheuse autour d'un tunnel excavé dans une région de construction d'une centrale électrique souterraine sous haute contrainte de roche initiale. Au cours des mesures, un phénomène de discage de carotte a été observé pendant le sur-carottage. La méthode de sélection des données de contrainte non influencée par le discage de carotte a été proposée, en utilisant un scanneur de tomographie calculée aux rayons X. Il s'ensuit que l'état de contrainte induite provoquée et déterminé à partir des données de la contrainte sélectionnées a été traitée, en effectuant une comparaison avec l'état de contrainte initiale.

Jan 1, 2003

By W. Stumpf

Mean flow stress analyses from plant mill logs for the conventionally produced hot rolled low carbon steel from the Ispat Iscor Vanderbijlpark strip producing plant, indicated a higher temperature sensitivity than that found for the equivalent SAE 1006strip steel produced in the compact strip plant of Saldanha Steel. This was confirmed quantitatively through detailed hot deformation studies on an as-cast structure as well as on a finer grained condition on the same steel. In the conventionally produced steel, activation energies for hot deformation of 309 kJ.mol-1and 388kJ.mol-1for the two respective starting structures were found, both values extending over the entire normal hot deformation temperature range of 1140 to 900°C. These and other experimentally determined constitutive hot deformation constants were applied to the hot rolling austenite grain size development model used earlier. From this, it is predicted that dynamic recrystallization occurs only in the first two break-down passes at the Vanderbijlpark plant and thereafter static recrystallization occurs after exiting from all of the remaining ten or eleven roughing and finishing passes. This is significantly different from what was predicted earlier for the Saldanha Steel plant with its lesser number of passes where static recrystallization is predicted to occur only in the last three passes. The effects of this process difference and other observed product differences between the two types of product are discussed. Keywords: Low carbon steel, hot rolling of strip steel, rolling mill log analyses, austenite grain size, grain size modelling.

Jan 1, 2004

By A. Fredriksson, R. Christiansson, I. Staub

A theoretical model based on DFN models and 2D DEM numerical modelling has been developed for evaluating the rock mass mechanical properties. The description of the methodology is non-site related and can be applied in any site for this type of characterisation. The methodology was developed in the frame of the Site Investigation programmes for a Deep Repository for spent fuel in Sweden, and validated on sets of data coming from the Äspö Hard Rock Laboratory. Un modèle théorique base sur des modèles probabilistiques de réseaux de fractures et sur un modèle numérique DEM 2D a été développé dans le but de déterminer les propriétés mécaniques de la masse rocheuse. La méthodologie développée peut être appliquée à tout type de site pour ce genre de caractérisation. Le modèle a été élaboré dans le cadre des programmes de recherche d’un site d’enfouissement des déchets nucléaires en Suède, et validé par une application au laboratoire de recherche souterrain à Äspö. Ausgehend von DFN-Modellen und 2D DEM numerischen Modellierungen wurde ein theoretisches Modell für die Auswertung von mechanischen Eigenschaften von Fels entwickelt. Die Methodikbeschreibung ist nicht standortspecifisch sondern kan überall für diesen Typ von Standordkarakteriserung angewendet werden. Die Methodik wurde in Schweden im Rahmen der Standortuntersuchungsprogramme für die Endlagerung von verbrauchten Brennelementen entwickelt und ist mit Hilfe von Daten des Äspö Hard Rock Laboratory validiert worden

Jan 1, 2003

By Y. Poornachandra Rao, P. C. Sudhakar, L. Malakondaiah

NBV commissioned a 27.6 MVA furnace in the year 2005. This paper explains: a)Furnace design features b)Furnace process control, Direct slag granulation c)Continuous casting, Waste heat recovery, Sintering d) Gas cleaning plant, Protection of Environment. Keywords: Furnace Equipment, SiMn Production, Casting, Heat Recovery and Low hood

Jan 1, 2007

By C. M. Rule

Energy efficiency is currently a significant area of interest due to the Eskom power situation, which led to severe power impacts to the PGM, and indeed whole SA primary industries, in early 2008. Anglo Platinum has focused on energy efficiency for a number of years, especially in the concentrator operational area. New comminution technologies have been aggressively developed, which have shown real metallurgical efficiency gains as well as significant energy efficiency and saving potential for Anglo Platinum?s total electrical consumption as the company expands into a growing PGM demand market. This paper illustrates this programme?s activities, potential and considerable achievements to date.

Jan 1, 2009

By Wynand Erasmus, Terry A. Jones

The Kelsey Centrifugal Jig (KCJ) utilizes the application of centrifugal force (and the resultant enhanced gravitational field) to conventional jigging technology principles to successfully process materials where the valuable constituent particulates are very fine and/or where there is a small specific gravity differential between these and the gangue minerals. The KCJ has been successfully employed in mineral sands applications in Australia for approximately 12 years. More recently, the KCJ has been tested and installed on zircon tailings dump retreatment projects in Australia and the USA, while being considered for similar projects in RSA, and is about to be installed in zircon tailings processing duties in India and Africa and in a tin removal duty in a rutile circuit in Australia. Extensive test work has been carried out on these applications and some typical performance data is presented in this paper. Information is also provided on the principles of operation of the KCJ and on the keys to a successful KCJ installation.

Deep level block caving as a mining method is becoming more popular due to the fact that it is the lowest cost per ton underground extraction system. However, many block caves do not achieve their full potential due to draw horizon instability. In this paper five design rules are given to overcome this problem. The design rules described are applicable for slusher and trackless block caves where the operational depths exceed 500 metres.

Jan 1, 1999