Search Documents

By A. Kondratiev

A structurally-based viscosity model for fully liquid silicate slags has been developed and applied to the Al2O3-CaO-‘FeO’-SiO2system at metallic iron saturation. The model links the slag viscosity to the internal structure of melts through second nearest neighbour bonds concentrations taken from the quasi-chemical thermodynamic model. This viscosity model describes experimental data over the whole temperature and composition ranges within the Al2O3-CaO-‘FeO’-SiO2system at metallic iron saturation and can now be applied to other industrial slag systems.

Jan 1, 2004

By J. Lux, B. Clermont

Magotteaux, with the co-operation of Anglo Platinum, has erected a fully instrumented pilot plant at Frank concentrator, which is being used to study the influence of a variety of grinding parameters. This paper will discuss only the influence of mill speed and pulp density on secondary stage grinding. A Ø0.82 x1 m open circuit mill was used with reclaimed Merensky tailings as feed. The conclusions apply to this pilot plant but further investigation needs to be done to verify whether the same trends will be applicable to a large industrial-scale mill.

Jan 1, 2004

By A. J. C. Paterson

High density slurry and paste tailings systems offer significant environmental benefits primarily related to reduced water consumption. However, these potential advantages need to be evaluated on a project-by-project basis. The successful design of a thickened or paste tailings system requires that the system is designed to accommodate the effect of the high density slurry on pumps, pipelines and the overall system operation. The transport system must be designed as an integrated unit and the interaction of all the components need to be considered. The transport system includes the slurry preparation plant, the pump station and the pipeline. This paper assesses the impact of increasing the slurry density in a platinum tailings system from conventional densities to thickened and paste tailings densities. As slurry density and rheology increase, there is a sharp increase in energy consumption for the additional water savings and this additional cost needs to be considered. A case study shows that there is a considerable benefit in increasing densities to the point at which tailings can be still be deposited in the standard manner. For existing systems, increasing density can result in an increased capacity at a marginal power cost, provided that the slurry is not too viscous. For a new system, a smaller pump and pipeline can result in lower capital costs and a marginally higher energy cost, if the optimum density is selected. Keywords: tailings, paste, pumping, slurry

Jan 1, 2004

By D. Yu, Y. Thibault, D. Paktunc

"Prereduction and flux-aided direct reduction of chromite provide significant advantages in reducing energy consumption and greenhouse gas emissions during ferrochrome production. In this investigation, a comparative evaluation of the influences of several alkali fluxes was carried out based on experimental observations supplemented by advanced material characterization and thermodynamic predictions. Direct reduction of a chromite ore with alkali fluxes at 1300°C for 1 hour produced (Cr,Fe)7C3 type alloys with Cr/Fe mass ratios from 0.7 to 2.3. Among the alkali fluxes, reduction aided by NaOH resulted in a high degree (85%) of Cr metallization with the ferrochrome alloy being Cr4.2–4.6Fe2.4–2.8C3. The formation of liquid slag, which facilitated Cr metallization, was limited by the formation of NaAlO2 between 800 and 1300°C. This, in turn, restricted the collection and transport of the charged ionic Cr species (i.e. O2–) to graphite particles. Under the conditions studied, ferrochrome particles were often small and largely unliberated, which would make the physical recovery of ferrochrome challenging. At 1400°C, the amount of liquid slag increased, enabling the growth of alloy particles. Direct reduction of chromite aided by NaOH is promising as an alternative technology to conventional flux-based smelting in electric arc furnaces. IntroductionConventional smelting processes are energyintensive (Riekkola-Vanhanen, 1999) with the energy requirements greater than 4 MWh/t (Naiker and Riley, 2006; Beukes, van Zyl, and Neizel, 2015), and the greenhouse gas emissions can be significant, exceeding 10.5 t CO2 per ton Cr in ferrochrome produced (International Chromium Development Association, 2016). These include emissions occurring on-site (smelter), emissions due to electricity production, and emissions due to upstream processes. Overall energy requirements are influenced by the degree of prereduction and smelter charge temperature. Significant reduction in electricity consumption can be realized if the charge is prereduced before feeding to the submerged arc furnace (Niayesh and Fletcher, 1986). This consideration has led to the development of several prereduction technologies, with the most important example being the Premus process. In comparison to the conventional smelting processes, this prereduction process lowers the overall energy consumption and greenhouse gas emissions by about one-third (Naiker, 2007)."

Dec 1, 2018

By G. van den Berg

Anglo Platinum has initiated a project to investigate hydraulic hoisting technology for platinum mines. Hydraulic hoisting systems are categorized as pumping, fluidizing feeder or displacement feeder systems. Positive displacement piston diaphragm pumps are most suitable for pumping systems but they require that the ore be milled prior to pumping. Fluidizing feeders are unsuitable for platinum ore applications due to the large percentage of fines in the ore. The three-chamber pipe displacement feeder has been most widely used for hydraulic hoisting and is the most suitable technology for platinum mines. Eight hydraulic hoisting applications covering pumping and displacement feeder technologies are reviewed. The key factors to be assessed in selecting a hydraulic hoisting system for a platinum mine are discussed. A typical platinum mine configuration will comprise an ore preparation plant (to produce -15 mm material through screening or crushing), motive water pump on surface, high pressure water pipeline from surface to underground, ore slurrification plant, three-chamber displacement feeder, and a high pressure slurry pipeline to surface. The water and slurry pipelines are housed in a purpose drilled borehole. A hydraulic hoisting system selection chart is presented. A 150 mm diameter system with a 25 MPa pressure rating is required to hoist 60 000 t/m from a depth of 1 200 m. Generic capital and operating costs are presented . A major potential advantage of hydraulic hoisting is that the fines, which contain a high percentage of PGMs, are captured underground and transported directly to the concentrator. Hydraulic hoisting technology is ideally suited to providing supplementary hoisting capacity to existing shafts that have reached the skip hoisting capacity limit. The main advantage for new shafts is the potential to significantly simplify underground rock handling and transportation. All hydraulic hoisting system components are proven. The only risk area is the wear rates of the valves and piping. Current estimates are based on gold ore. The business cases investigated show that the financial viability of the installations are not sensitive to wear rate. Hydraulic hoisting is technically feasible and financially attractive for platinum mines. Keywords: Hydraulic hoisting, slurry

Jan 1, 2004

By R. Webber-Youngman

The Department of Mining Engineering at the University of Pretoria accepts that the process of teaching and learning improvement is an ongoing exercise with the ultimate aim to deliver well-rounded mining engineering practitioners. Various challenges impact on the success of this process. An integrated and innovative process was developed and is followed in the Department to overcome these challenges. The aim of the Department is to apply a holistic teaching approach by introducing multiple integrated interventions with regards to teaching and learning strategies. Three phases of this process are discussed in this article, and are illustrated in Figure 1. During the first phase, prior to 1999, several teaching and learning challenges were identified in the Department of Mining Engineering. These challenges are discussed in the next section. In the current phase, a variety of interventions to address the challenges are being developed, implemented (in some cases piloted), and evaluated. The future phases will focus on the improvement, successes, and full roll-out of current interventions, as well as on training, development, and support for all staff members to participate in the process. (Figure 1)

Jan 1, 2011

By S. Ramatsoma, D. N. C. Phillpotts, B. Whitehead

Changes in flotation performance have been correlated to changes in froth structure, velocity and stability. Literature has shown that when the aeration rate is varied for a specific float cell, the recovery of the valuable mineral reaches a peak which also coincides with a peak in the air recovery – a measure of froth stability. Peak air recovery optimisation methodology is a way to use direct readings of physical phenomena by froth cameras to optimise the metallurgical performance of a flotation plant. The aim of this paper is to show the transient nature of the peak air recovery value and the variety of conditions required to attain the peak air recovery on an industrial flotation plant with tight base-layer control of the feed and internal conditions. Industrial site tests that were conducted under controlled conditions showed different peak values at significantly different corresponding aeration rates during normal operation. The measured peak air recovery points corresponded to maximum PGM recovery during normal flotation, as expected. This dynamic nature of the peak air recovery point conditions has not previously been discussed in literature and indicates the need for online measuring equipment and informs the design of process control algorithms required to exploit the phenomenon for optimisation. Keywords: Froth flotation, flotation control, flotation optimisation, peak air recovery

Jan 1, 2020

By J. V. Simmons

Composite rock mass failures involve intact rock material as well as fracture and shear on existing defects. Experiences from open-cut coalmining in the Bowen Basin of central Queensland are that failures of this nature occur suddenly with little warning, and are much more common than classical structurally controlled failures. Geological conditions and mining practices in the Bowen Basin are described. The circumstances of a sample of composite failures are described in detail in the paper. From this experience it appears that several aspects of conventional geotechnical investigation and design practice have not contributed significantly to either predicting or controlling the risks associated with sudden failures. These practices are described as myths for reasons outlined in the paper. On the other hand, the reality seems to be that high initial stresses and stress changes caused by excavation lead by a process of extensional deformation to a critical stress condition within the rock mass, and that sudden collapse follows when that critical stress condition can no longer be sustained. It is concluded that learnings gained from underground excavations in rock may be more applicable to open pit excavations than previously thought, and that the processes of prefailure deformation require more careful study if we are to develop more reliable risk management controls.

Jan 1, 2006

By T. Lindstad, S. Gaal, S. Hansen, S. Prytz

The SINTEF SiO-reactivity test, developed by Tuset and Raaness in the 1970?s, is a recognised method of characterising the ?reactivity? of carbonaceous reactants, used in the ferrosilicon and silicon metal industries. Recently, the test has been updated, which has resulted in the development of an extended and improved SINTEF SiO reactivity test. This has included updating the test reactor, control system, data-logging, handling and preparation of carbonaceous materials to be tested and measurement procedure. The scientific basis has been re-assessed, resulting in a new interpretation of the test results. The repeatability of the test has improved significantly, especially through system automation. In the ?old? test, the kinetics of the reaction: SiO(g) + 2C(s) = SiC(s) + CO(g) for a specific carbonaceous material was characterised solely by the ?R10? parameter, the volume of SiO(g) which passes un-reacted through the coke-bed as the concentration of CO in the outlet gas decreases from 18 to 10%. As both the kinetics and obtainable conversion of SiO to SiC for a reductant is of importance to the ferroalloy producer, the new SINTEF SiO reactivity test ranks carbon materials both according to degree of conversion and reaction rate. From research carried out on the test in the past couple of years at SINTEF and NTNU, it has also become clear that some of the reactions taking place in the test reactor are more complex than previously assumed. As an example, it was previously assumed that the condensation reaction of SiO gas in the condensation chamber of the test reactor can be described as: 2 SiO(g) = Si(l,s) + SiO2(s). However, it has been established that the side-reaction: CO(g) + 2Si(l) = SiC(s) + SiO(g) causes approximately 10% of the total volume of CO to react to SiC and SiO2 in the condensation chamber. This means that some back-reaction i.e., the reverse SiO-generator reaction 3SiO(g) + CO(g) = 2SiO2 + SiC also takes place in the condensation chamber. In the new SINTEF test, the %CO versus time curves are therefore corrected in order to describe the effect of the reaction between SiO(g) and C(s) studied i.e., SiO(g) + 2C(s) = SiC(s) + CO(g). A correction-formula for this purpose is presented.

Jan 1, 2007

By K. C. Mills, R. Thackray

A test has been devised that can predict accurately the % crystallinity developed in a slag film formed between the steel strand and the mould. The % crystallinity in the test samples was determined and compared with that for slag films formed in the mould when casting with that flux. There was good agreement between the % crystallinity in the test samples and the slag films. It was found that additions of TiO2and ZrO2had little effect on the amount of crystalline phase formed, but additions of CaO caused a dramatic increase in the amount of crystalline phase formed. Various parameters (which can be calculated from chemical composition of the flux) have been plotted against % crystallinty in the test samples. It was found that the modified (NBO/T) ratio provided the best relation with % crystallinity for the various parameters tested. There commended relation is % crystallinity=141.1(NBO/T)-284.0. Keywords: continuous casting, mould flux, slag film, crystallinity, chemical composition

Jan 1, 2004

By C. Sahyoun

The influence of microwave treatment on copper flotation has been investigated. Comparative batch flotation tests carried out on ore treated at 5?12 kW for 0.1?0.5 s showed that improvements in copper recovery of between 6?15 % could be achieved compared with untreated ore. Both recovery and cumulative grade increased with increasing treatment time and power. A preliminary economic analysis showed that microwave treatment will be economically viable if recoveries similar to those determined on laboratory scale can be achieved on a plant. Keywords: microwave treatment, copper ore, flotation, liberation, recovery

Jan 1, 2005

By J. Böhlke, B. Friedrich, E. Hecker

The legislation for the disposal of heavy metals contaminated substances is still going to be tightened up in the future. The main criteria for the utilization or deposition of these residues are the content and the water solubility of these metals. Through this, the use of slags from the lead-and zinc-industry in road building may become limited or even not possible at all. From an economic point of view this would lead to Pb/Zn losses and costs for safe dumping. This paper investigates the feeding of the reducing agent via hollow electrode DC smelting and the yield of metal reduction. After carrying out thermodynamic calculations, the process window conditions for electric-arc furnace tests were determined. Doing this, the zinc could be reduced, evaporated and recovered as an oxidic intermediate product flue dust, while the lead was present either in flue dust or in metallic form. The zinc content in the final slag could be reduced by up to 90%. The slag product has undergone an eluation test which allows it to be used as building materials. Keywords: zinc reduction, lead reduction, hollow electrode, slag treatment, electric arc furnace

By A. Andrews

Paper written on project work carried out in partial fulfilment of MSc (Eng) degree Solid state sintered silicon carbide ceramics are used in aggressive environments as sealings. There exist data concerning corrosion, but there are only few data concerning their electrocorrosion behaviour. Therefore the electrochemical corrosion of solid state sintered silicon carbide (SSiC) ceramics has been studied at room temperature in acidic and alkaline environments by using potentiodynamic polarization measurements. The investigation showed a pronounced electrochemical corrosion in bases and acids. In HCl andHNO3pseudo-passivity features due to the formation of a thin layer of SiO2on the surface were observed, whereas in NaOH soluble silicate ions were observed, resulting in more pronounced corrosion. The microstructural observations of initial and corroded samples reveal that the residual carbon found in the microstructure do not dissolve preferentially. Keywords: Corrosion; SEM; SSiC; polarization test.

Jan 1, 2006

By C. B. van den Berg

n this study, silver and palladium nanoparticulate inks with different metal-binder ratios were screen-printed onto a paper substrate. The printed layers comprised the metal nanoparticles and an ethylcellulose binder. The layers are not typical metal composites due to the low concentration of binder and high porosity. The electrical sheet resistivity of each particle concentration was measured, and the data fitted using the scaling law of percolation theory and the general effective media (GEM) equation. The percolation parameters, i.e. the percolation threshold and the critical exponent, for each system were determined from the fits and compared. The percolation threshold for the palladium layer (39.8 wt%) was lower than that found for the silver layer (44.9 wt%). The critical exponents determined for the palladium and silver layers were both lower than the universal value for three-dimensional percolation systems. Microscopy observations indicate that the difference in the percolation threshold for the two layers can be attributed to variations in their microstructure.

Jan 1, 2014

By P. R. Scheller

Reactions between metal and slag are of decisive importance for metallurgical processing. In the continuous casting process, where metal solidifies at the metal-slag interface, reaction products can cause surface defects, with quality damages of the cast products as a consequence. These investigations are focused on the contact area between casting flux and metal. The samples were taken from the mould during the casting process. The results show that layers up to approximately 300 nm from the slag/metal interface represent a specific reaction space. Sodium in this layer on the slag side plays a specific role, which is explained on the basis of experimental results. The transport of oxygen near the interface and the charge transfer is explained on the basis of the ionic character of the slag. The mass transfer rate of oxygen crossing the interface is calculated from measured data, and conclusions concerning the stability of the interfacial tension are made. Keywords: mass exchange, metal slag reaction, interface, ion transport, oxygen transfer, oxidation, casting slag, flux, sodium

Jan 1, 2004

By M. Sephton

Slat-band chains, currently manufactured from Type 430 ferritic stainless steel, are used as conveyors in various industries. A process to strengthen these chains?with the aim of prolonging the lifetime of the conveyors?was developed recently. The process entails heat treating the cold-worked chain at 475°C,strengthening the material by precipitation of the Cr-rich phase a? at relatively long periods of aging. In the present work, it was found that increasing the interstitial content by solution heat treatments (at 880°C or 930°C) prior to cold rolling and aging, causes an increase in strength at shorter aging times as a result of the precipitation of chromium-rich carbides and nitrides. The solution treatments can introduce martensite into the microstructure if carried out at a sufficiently high temperature. This, along with the deformation caused by cold work, also increases the strength. Corrosion resistance is not affected by the treatments, but ductility is lowered. However, calculated critical crack lengths indicate that solution treatment at a temperature below the Ac1allows for a larger critical flaw size, and that the lifetime of the chains will probably be determined by fatigue. Although the duration of the service of the chains are reportedly controlled by wear, with these treatments the tensile strength of the material is increased to within acceptable limits for conveyor chains. The tensile strength is an indication of the wear or abrasion resistance of a material. It is expected that after the treatments, the wear resistance will be improved, but since embrittlement occurs, the fatigue resistance is lowered. It is concluded that the preferred processing route for the chains would be solution treatment at 880°C, fast quenching to trap the interstitial atoms, cold rolling and then aging at 475°C for 8 minutes.

Jan 1, 1997

By M. van Biljon

The possible closure and subsequent flooding of South Deep Gold Mine?s neighbouring Randfontein Estates Limited No. 4 Shaft (REL 4) necessitated the construction of five concrete plugs in the connecting tunnels to prevent the ingress of groundwater into REL4 from flooding South Deep mine. Several technical investigations had been carried out before and during construction of the plugs in order to reduce the probability of groundwater flow through the boundary pillar between the two mines or through the rock mass immediately around the plugs. This paper describes the geological, hydrogeological and stability investigations carried out to evaluate the structural competence of the boundary pillar.

Jan 1, 2006

By J. S. Harington

Our purpose is to record and to explain the widely changing numbers of the huge total of black workers on the gold mines of South Africa over the century from 1896 to 1996. These men were recruited from up to twenty territories, and their contributions are examined. The major areas providing labour over this long period have been Lesotho, the former Transkei within South Africa and Mozambique. From 1989 to 1996, for instance, these three areas accounted for over sixty per cent of the total labour force (tlf). Our principal Figure 1 shows the tlf fluctuating through time to reach a peak of 480 000 in 1988. Irregular falls are also documented with the most serious in 1995 to 180 000. Based on this graph we consider the political, economic, sociological and historical reasons behind these changing employment opportunities. These have included external world-scale events such as war or depression, as well as internal changes of national economy and policy. We show the importance for numbers employed of the discovery of gold in the Orange Free State in 1946, the influence generally of the ?Winds of Change? and the firm maintenance by the State of law and order. Varying gold production costs and profitability against high tax rates, allied with increasing wages and a lack of development capital, have led in the last decade to employment falling by fifty per cent, despite an actually higher value of gold output. Finally, this analysis considers the role of the migrant labour system as it affects, and is affected by, conditions in the gold mining industry, with special reference to its less than humane consequences in the numerically dominant territories of Lesotho and Transkei.

Jan 1, 2004

The aim of this investigation was to study the influence that varying production rates have on iron sinter quality. This was done by performing sinter pot tests at different pressure drops over the sinter bed, namely 11 kPa and 15 kPa (for 500 mm total bed depths). During each of the sintering processes temperature-time profiles were recorded of the top, middle and bottom layers of the sinter bed. On completion of the sinter process the sinter cakes were divided into top, middle and bottom layers. The physical properties of each layer were subsequently characterized by performing a tumbler test and a sieve analysis. A comprehensive mineralogical study was also conducted on each layer. This study revealed that sinters of similar cold strength could be produced under the examined production rates. However, a higher production rate was accompanied by an increased amount of fines. The cold strengths of both sinters significantly increased from the top layer to the bottom layer of the sinter bed. This strength variation is not related in any simple way to the phase composition. Keywords: Sinter, sinter bed, production rate, phase composition, cold strength, tumbler index, sieve analysis, temperature-time profile

Jan 1, 2003

By C. B. Espag de Klerk, J. de Goede, M. Le Roux, Q. P. Campbell

"Excessive amounts of moisture in product coal can influence the efficiency of downstream utilization processes due to a decreased calorific value and handling problems. Stockpiles can be used to decrease the moisture content of coal by means of gravity drainage and evaporation. This paper is focused on the evaporation of moisture from a coal stockpile surface with the aim of investigating the effect of particle size on the rate of evaporation as well as the depth to which evaporation extends.It was observed that moisture initially evaporates at a higher rate from a stockpile consisting of fine particles (-6.7 mm) than from coarser particles (-13.2 mm +6.7 mm). This high rate of evaporation is restricted to the outer shell of the fine coal stockpile. However, for coarse coal, the porous nature increases the depth at which evaporation occurs. Evaporation of moisture was observed up to the fourth day of each experimental run, after which steady state was obtained. It was shown the water can evaporate from the surface into the body of the stockpile, depending on the coal particle size and void spacing. An experimental reclaim depth of 0.4 m was achieved after 4 days. IntroductionCoal stockpiles serve as surge capacity for downstream utilization processes and can also be used for moisture reduction by means of gravity drainage and evaporation. Excessive amounts of moisture in coal can cause handling problems and, most importantly, will decrease the calorific value, leading to inefficient combustion.Research has shown that evaporation by means of wind and solar action is considerably more effective than gravity drainage(Williams, D.J. 2006), but the effect is limited to a restricted depth from the exterior of the stockpile (Boyapati, E. and Oates, A. 1994; CSEM-UAE, 2010). The effectiveness of wind and solar action can be improved by orienting the stockpile perpendicular to the predominant wind direction, maximizing the surface area of the pile, and reclaiming the coal from the pile gradually in shallow cuts over a large area (Williams, D.J. 2006)."

Jan 1, 2016