Search Documents

By L. H. Wullstein

Bureau of Mines research on methods for reclaiming land disturbed by the minerals sector of the economy has produced a specific procedure for effectively germinating seed of Indian ricegrass, a drought-tolerant plant valuable for reclaiming arid and semiarid sites. This report describes the procedure which consists of acid-treating the seed followed by temperature and light cycling treatments. Use of the procedure resulted in an average germination rate of 29 percent, ranging from 18 to 56 percent. Seed subjected to long cold treatment but with acid treatment yielded an average germination rate of 9.2 percent, ranging from 6.6 to 14.7 percent. Untreated seeds (controls) gave germination rates less than 0.1 percent.

Jan 1, 1979

In 1967 the United States consumed 58.8 quadrillion Btu of energy. Both the Atomic Energy Commission and the Resources for the Future, Inc., a private economic forecasting group, predict that the United States energy requirements will reach 135 quadrillion Btu by the year 2000. In 1967 bituminous coal produced 21.4 percent of the energy used in the United States and anthracite coal another 0. 5 percent. Coal Reserves Coal reserves make up about four-fifths of the United States storehouse of fuel in proven reserves. Seventy-five percent of all fuel, likely to be found and recovered is coal. Electric utilities consume more than half of the bituminous coal mined in the United States in generating 53 percent of the nation's electricity. Atomic Energy Commission analysts have proposed the development of a vast "national energy system" based upon long-distance electrical transmission from abundant untapped coal reserves in the western United States. The study predicts that even if uranium supplies are available and economic breeder reactors developed, coal requirements for electricity generation will more than double by 1980 and increase another 50 percent before the year 2000.

Jan 1, 1970

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made an the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by over 30%, on the average, with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By David A. Monaghan

On January 14, 1974 a fire occurred in the 3 East mains of the Joanne Mine of Eastern Associated Coal Corp. in Rachel, West Virginia. The mine was evacuated without injury and sealed completely at the surface within 24 hours. It was decided by the coal company along with the U, S, Bureau of Mines, the West Virginia Bureau of Mints and MESA that remote sealing of the fire zone would be attempted. This report summarizes the remote sealing effort and those activities directly related to the remote sealing effort. This chapter provides a brief history of previous remote sealing attempts, a description of the recently developed remote sealing system and a description of the Joanne Mine operation as it related to and affected the remote sealing effort.

Jan 1, 1975

By J. D. Warne

The ferberite district of Boulder County, Colo., has been an important producer of tungsten since 1900. During World War I, high prices for tungston concontrates resulted in a brief period of intense activity, and the production in 1917 was 2,707 tons of 60 percent W03 concentrates. Production declined thereafter, and in 19.2 the tungsten produced in Boulder County represented about 4 percent of the Nation's output, being exceeded only by the scheelite production in California, Nevada, and Idaho. Boulder County has boon an important source: of tungsten in the Korean emergency; the present report does not describe this recent activity, as it will be covered by a future publication. Tungsten occurs in small ore shoots of narrow and irregular veins. Most of the ore shoots have been found outcropping on the surface. Core drilling; has been used by the larger operators to explore for new veins and to locate extensions of known veins.

Jan 1, 1953

By Bernard M. Larsen, Clyde F. Williams, Edward P. Barrett

"Introduction.The Bureau of Mines at its Northwest Experiment station has been studying the production of sponge iron for the past four years, and during 1923 progress advanced to the point industrial applications can be safely considered. A furnace was operated commercially at silver City, Utah, producing about three tons of sponge iron daily.The Bureau was led to undertake this work by the interest in the use of sponge iron for copper precipitation and for conversion to iron and steel in the electric furnace.If a piece of iron oxide is completely reduced at such a low temperature (850 to 900° C) that no sintering or fusion takes place, then the piece of metallic iron formed has the same size and shape as the original piece of oxide on account of the removal of oxygen, the structure is finely porous, exposing a large surface of iron, and the apparent density is less than that of the original piece of iron oxide. This material is called ""sponge iron"". Chemically, it is a very reactive material."

Nov 1, 1924

By W. J. Fene, G. W. Grove

An important activity of the Safety Division of the Bureau of Mines , in its efforts to reduce accidents , is the safety inspection of mines . Inspections are made at the request of the operators and are not connected with the inspections by the various State departments of mines . The operating management is furnished with a confidential report of the results of the Bureau's inspections , with recommendations for elimination of the hazards found . These mine - safety inspections include a study of mining practices , conditions , and equipment and in some cases the sampling and analysis of mine air and coal dust . The Bureau of Mines has no regulatory powers , therefore the recommendations made in these reports are merely suggestions , and operators are not required to adopt them . Mine inspections are a check on safety standards , methods , and practices and are essential to any accident -prevention program . A foreman or superintendent may be sincere in his efforts to operate a mine safely and believe that he has done everything possible to attain this end . However , experience has shown that because of his familiarity with the mine and the consequent " nearness " of its various features many unsafe conditions may be , and in most cases are , overlooked ; an inspector , particularly an outsider who is trained to look for hazards , can point out the unsafe conditions overlooked by the foreman or superintendent . Some companies employ safety engineers who make regular inspections of their mines , report substandard conditions and hazards found , and make recommendations for correcting them . Unless these recommendations are carried out the inspections have little value . In making recommendations , due consideration should be given to the feasibility of carrying them out ; the management may and very often does consider a recommendation impracticable because of the

Mar 1, 1935

The design, specification, and performance evaluation of the Communications and Location portions of a Coal Mine Rescue and Survival System are described. The work was performed as part of a nine month effort to develop a mine rescue and survival system using existing technology and state -of-the -art hardware as recommended by the National Academy of Engineering. Three basic subsystems were developed, one for survival, one for communications/location and one for rescue. This report and related equipment manuals describe only the Communications/ Location Subsystem which was designed, fabricated, and tested by the Westinghouse Georesearch Laboratory in Boulder, Colorado. Two basic technologies were used. Electromagnetic signals propagating through-the-earth provide voice downlink and coded beacon up-link communications. Seismic methods were developed to provide means for locating trapped miners. Seismic signalling also provides a backup means for communications. Parallel development programs for the electromagnetic and seismic portions of the system were conducted. The resulting hardware and software have been partially tested in coal mines and under simulated emergency conditions in order to evaluate system performance. The results of these tests are discussed. Further testing is recommended in order to establish quantitative performance limitations tinder a variety of environmental conditions and to develop methods for improving system performance.

Jan 1, 1971

By Albert L. Toenges

This paper is the third of a series4/ that describes some methods and practices of mining coal mechanically where operations are conducted on more than one shift. The mining of coal by means of mechanical devices has emphasized the need for continued study of the relationship, of these devices to existing physical conditions and to planning of the operations for increased safety and economy. The purpose of this investigation is to stud the operations of different types of mechanization used in mines under various systems of mining and physical conditions to reach conclusions as to the safest and most economical methods and practices of mining. Physical conditions very in different and in the same mining districts and determine, together with economical conditions, the systems of mining and the types of mechanical loading equipment used. The information presented in this paper

Jan 1, 1941

By R. G. Warncke

In the 1953 National First-Aid and Mine Rescue Contest, 58 teams from 9 States participated, 14 teams from 6 States in mine rescue and 47 teams from 9 States in first aid. Three of the teams were combination teams in that the same team participated in both the mine rescue and first-aid contests. The States represented and the number of teams from each State are shown in table 1. [ ] The contest was conducted in accordance with the general rules prepared by the Rules Committee and approved by the General Committee of the National First-Aid and Mine Rescue Committee.

Jan 1, 1955

To develop a conceptual design for an automated longwall mining system, one should know what has been done, what is being done today and what is being planned for tomorrow. The bibliography referenced and discussed in this report provides a good source for that knowledge. To scientifically determine where attention should be focused to up-grade a system, the system must be quantized as far as possible. The Mechanization Profile of Appendix A-I is discussed in this report and has been used to analyze and determine the degree of mechanization currently in use and/or described in the literature for all three major elements of the long-wall system, namely, Winning, Roof Support and Haulage. The charted profiles make it self-evident where attention and design effort is needed to remove human operators from the face of the mine.

Jan 1, 1975

By Charles H. Fulton

One of the first matters to receive attention from the Bureau of Mines when it was authorized to undertake investigations relating to wastes in the mineral industries was the smoke problem at smelting and ore-roasting plants. This bulletin is published by the bureau primarily for persons who seek information on the subject of metallurgical smoke but are unacqllainted with the technical language of metallurgy. It is, of course, not possible to free a techniCal subject entirely from teclmicalities, but, 80 far as possible, statements are made in plain and simple English. Metallurgical smoke causes considerable friction between the metallurgical industry and agriculture in certain parts of the country. Owners of smelting plants are making every effort to devise ways and means to do away with possible damage and annoyance from smoke and are meeting with success. The problem is peculiarly difficult in this country because of the large tonnages of material that must be handled. The solution of the problem is not yet at hand and much work still remains to be done. As the mineral industry is one of the great basic industries of the country and of necessity is entitled to full consideration, it should be accorded freedom to work out the smoke problem to the benefit of all concerned. The effort is made in this paper to present the problem of metallurgical smoke as it actually exists, without bias of any kind. The writer takes this opportunity to express his indebtedness to the sources of information on which he drew, many of which are enumerated in the selected bibliography at the end of this paper. In connection with the author's use of the present tense in describing plants and methods, the reader should note that none of the references in that bibliography is of later date than 1913. Much information was obtained by personal visits and by correspondence, and thanks are hereby tendered to all persons who kindly furnished data. The writer desires to thank particularly F. G. Cottrell, chief chemist of the Bureau of Mines, for criticism and comment.

Jan 1, 1915

By Mervin D. Marshall

A quick-reaction, mine permissible rescue vehicle (MERV) was developed for use by rescue teams. The MERV is a 6-wheeled, battery-powered unit with life support equipment and instrumentation; designed for a two-man team, with provisions for handling two victims or tools in a trailer. The vehicle is 100 inches long, 56 inches wide, and maximum height of 34 inches. It can be lowered down most mine shafts and has clearance to travel mine railways. The vehicle has power to all six wheels with power transmitted separately to either or both sets of wheels. Low-pressure, high-traction tires give the vehicle the ability to handle soft, muddy mine floors, flooded areas and significant obstacles, and can negotiate a 45% grade. Power and life support are sufficient for a 4-hour mission. The life support system is a commercially-available, approved unit currently used by MESA rescue personnel. A payout wire system provides communication between the vehicle and home base over a distance of 10,000 feet. On-board monitoring of carbon monoxide, methane and oxygen is provided, with master and individual alarms to warn of gas concentrations outside pre-set limits. A lightweight, water-tight trailer was developed for carrying victims or hauling tools and equipment.

Jan 1, 1979

By Thomas O. Glover

Cameroon's mineral industry continued to be dominated by crude petroleum. The country's economic development depended on the production and export of crude oil. Oil output was estimated to be 56 million barrels in 1984 compared with 47 million barrels in 1983 and 39 million barrels in 1982. The country's only refinery processed approximately 16,000 barrels per day of crude oil in 1984, operating at slightly over 50% capacity. This volume, however, supplied the domestic need for motor fuel and heating oils. Cameroon's economy continued to expand despite problems and setbacks stemming from the attempted coup of April 6, 1984. Gross domestic product (GDP) growth in 1984 was 6.5%, the same rate as in 1983. Offshore crude petroleum production was the chief factor in the sustained economic growth. The country also maintained a relatively strong balance-of-payments position through oil exports. Investment, ranging up to 25% of the GDP, greatly contributed to sustained growth. The oil sector contributed approximately 14% to Cameroon's GDP in both 1983 and 1984.

Jan 1, 1986

By M. R. Geer

The Bureau of Mines surveyed the solid wastes that have accumulated from coal mining in Washington, Oregon, and Montana. Location, amount, character, and condition were determined, and both economic and environmental factors were considered. Areas covered by waste comprise 800 acres in Washington, 5 acres in Oregon, and 1,200 acres in Montana. In a few cases waste is being utilized, particularly cinder from burned refuse dumps, as fill in road construction and as a ceramic raw material. It is estimated that wastes deriving from coal mined for electric power generation by 1974 may amount to 3 million tons of washery refuse, 2.7 million tons of fly ash, and 1,000 acres of spoil banks.

Jan 1, 1969

By Joseph M. Pugliese

This work was done by the Bureau of Mines to provide quarry operators with an uncomplicated, first-approximation method for designing blast patterns, considering geologic structure, and to show the valid use of the technique by comparing drill and blast pattern dimensions used in the quarry with those determined by the presented method. The author visited 12 limestone and dolomite quarries in Ohio (Adam, Crawford, and Highland Counties), Wisconsin (Milwaukee, Racine, and Waukesha Counties), and Minnesota (Fillmore, Olmsted, and Wabasha Counties); observed the blasting practices; studied the major geologic features; and after discussion with the quarry managers, foremen, and blasters, compared the quarry blasting patterns with those as calculated by the empirical formulas (after R. L. Ash), with geologic structural considerations. When geologic structure such as bedding, jointing, folding, and caves, as well as explosive properties and field performance characteristics are accounted for in a manner suggested by the research, the presented empirical formulas may be used as a good first approximation. The included steps in planning a blast design and generalized blast patterns should be of help to the quarry operator. Design changes are recommended for those quarries where problems are occurring.

Jan 1, 1972

By Haskiel R. Shell

While the original purpose of the Bureau of Mines work on fluorine micas was to synthesize large single crystals or film suitable to replace natural muscovite or phlogopite, the objective was broadened to include development of the many possible fluorine micas as a class of new, unique materials. Several methods were developed for the synthesis of the fluorine micas at atmospheric pressure: Solid state reaction, melting in crucibles, internal resistance electric melting, and arc resistance electric melting. The latter two methods are now med commercially. A variety of fluoromicas were synthesized by isomorphic substitution including disilicic, trisilicic, and tetrasilicic. Fluorophlogopite, KMg3AlSi3O10F2, is the fluoromica most widely used. While most of the fluoromicas are completely stable to water, many water-swelling fluoromicas and fluoromontmorrilonoids were synthesized. Single crystals or film of the fluorine micas were grown to 2 inches or more by a number of methods, but none has as yet proved economical. In the report, detailed data and descriptions are given on compositions, syntheses, products, and uses, and on the properties including physical, dielectric, chemical, X-ray, optical, and structural.

Jan 1, 1969

By K. C. Dean

The Bureau of Mines, following passage of the Solid Waste Disposal Act of 1965, was authorized to conduct research on methods for utilizing, stabilizing, or reclaiming mineral wastes. This report summarizes laboratory research conducted by the Bureau and cooperative field studies made with the mineral industry to reduce the environmental impacts of air and water pollution deriving from mineral wastes. Utilization research showed that both dry-press and steam-cured building bricks and ceramic tile could be made from copper mill tailings and other discarded mineral wastes. Sponge iron was produced from steel mill and amination industry wastes, and valuable mineral products were extracted from such diverse sources as flue dusts and uranium tailings. Mineral wastes were combined with agricultural and/or sewage wastes to make artificial soils that have the potential of resolving several disposal problems by production of a useful commodity. Physical, chemical, and vegetative stabilization methods were evaluated, singly and in combination, for reclamation potential on copper, uranium, lead-zinc, and asbestos tailings. Suitable methods were developed in the laboratory for overcoming major adverse conditions of these wastes such as salinity, heavy metal toxicity, acidity, basicity, lack of nutrients and organics, and unstable surfaces. Field testing of these methods was performed on a variety of mineral wastes. Costs for the various stabilization and utilization-procedures developed were also determined.

Jan 1, 1986

By Clark P. Mangelsdorf

The report consists of two parts. In Part I is a state-of the-act study of roof truss technology as of January 1979. Included are a history of the truss concept, a review of analysis techniques, a record of hardware available and equipment used in its installation and numerous examples of user experience. Part II is concerned with a study of the role of friction in the behavior of a roof truss. The appendices include laboratory tests by the author.

Jan 1, 1979

A compilation of papers presented at the Third WVU Conference on Coal Mine Electrotechnology in Morgantown, West Virginia, on August 4-6, 1976. Papers cover areas of electric power, electronic communications, detection and location of trapped miners, and electronic sensors and monitoring systems.

Jan 1, 1976