Search Documents

By H. G. Iverson

Solid state reactions of manganese with silica were investigated in high-temperature tests. Reactions of 0.5 to 4.0 moles manganese (Mn) with 1 mole silica (SiO2) at 1,100° C and of 2.0 Mn:SiO2 mole-ratio mixtures at 1,000° to 1,150° C yielded products consisting of a slag phase and a metallic phase. At 1,100° C, the slag phase from reactions of the low Mn:SiO2 mole-ratio mixtures was composed of SiO2 and rhodonite (MnSiO3), and the slag phase from the high Mn:SiO2 mixtures was composed of MnSiOs and tephroite (Mn2SiO4). The metallic phase from the corresponding low Mn:SiO2 mole-ratio reactants consisted of two manganese silicides, Mn5Si3 and Mn3Si; from the high Mn:SiOg mixtures, it was Mn and the manganese silicide (Mn5Si). For the higher mole ratios of MnSiO2 the manganese content in the metallic phase increased, while the manganese and silica contents of the slag phase remained nearly constant. The slags did not contain free or uncombined manganese oxide (MuO). For the 2.5 to 4.0 Mn:SiO2 mole-ratio mixtures reacted at 1,100° C, the maximum quantities of silica reduced and of the manganese in the slag appeared to become asymptotical at about 41 and 48 percent, respectively. A brominating procedure was developed that was highly selective in removing the metallic constituents from the reaction product, leaving the slag phase as residue. X-ray diffraction patterns were obtained on prepared silicides Mn5Si, Mn3Si, and MnSi.

Jan 1, 1967

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed. Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963

By H. Kenworthy

The objective of this investigation was to evaluate the technical feasibility of smelting certain low-grade domestic iron ores in an electric furnace. Laboratory-scale experiments showed that a high recovery of iron in the form of pig iron can be obtained from east Texas ores containing less than 25 percent iron. The pig iron was amenable to standard-or electric-furnace-refining methods for producing steel. Car-bon, silicon, and phosphorus were the primary impurities removed in refining. Overall recoveries of iron as pig iron exceeded 95 percent, in contrast with commercial mineral-dressing recoveries on these particular ores of 50 percent of the iron as a 45-to 50-percent iron concentrate.

Jan 1, 1958

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed, Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963

By T. Whitrnoyer, J. Sneckenberger

"The acOustic impedances of seven rat lungs were measured at frequencies between 100 and 6400 Hz. Rats were divided into two groups: a silica exposed group (N=3) and a control group (N=4). The silica exposed group was injected intratracheally with silica solution. Three of the control group were intratracheallyinjected with saline. Between four and six weeks after theinjections, all lungs were excised and degassed. Lungs were,suspended in a pressure Chamber, with the trachea canula attached to the end Of a tapered impedance tube. The lungs were subjected to transpulmonary pressures between -30 cm H2O and 6 cm H2O to simulate deflation and inflation. With transpulmonary pressure being held constant, the impedance tube was excited with random noise. A dual channel analyzer calculated H12(f), the transfer function between the two microphones. This function was used to calculate the lung's impedance at that pressure. The impedance magnitude spectra of both groups typically had peaks at 2000,3500, and 5500 Hz. Statistically significant differences. (90%confidence level or greater) between the two groups occur at the 3500 Hz peak at transpulmonary pressures of 20, 8, 6, 4, and 2 cm of H2O. This fact seems to confirm that this method can detect. lung disease. Further research will indicate whether this method will be able to detect the onset Of coal worker's pneumoconiosis.INTRODUCTIONOne of the first studies of impedance Of the human lung were conducted by DuBois et al.[2] using the forced OscillatiOn technique. This technique, however, was limited to frequencies below 30 Hz. Further studies by Van Den Berg [6] revealed thatthe lung reflected higher frequency sounds (100-10,000 Hz), instead Of behaving as an anechoic termination. This discovery has lead to several studies of the acoustical properties of both human and animal lungs at high frequencies [3,4,5]."

Jan 1, 1988

By L. C. IlsLey

So many subjects are covered in State mine-safety regulations that any attempt to compare different State laws in their entirety would be futile. On the other hand, if one selects a single phase or branch of safety work, such a comparison may prove profitable. The subject selected for study in this paper is limited to legislation or regulations dealing specifically with safeguarding (electric) motored equipment used in gassy mines. T When one reads glowing accounts of the safety activities being carried on here and there it is easy to believe that everything which is right and proper is being done to safeguard the mine.workers; but, when one takes time to look into the weakness of many State regulations, it is evident that there is still room for improvement. Undoubtedly it would have been much better for the safety of mines if electrical equipment had been introduced into mines 50 years earlier. If electricity had been in general use when the first mine regulations were pre- pared, those formulating the rules would have covered this hazard along with other hazards, but as electricity came in at a later period, safe mine legisla- tion regarding it has been woefully neglected. Today the United States in general is far behind most other coal-producing nations in the provision of adequate safety rules or laws for the installation and maintenance of electrical equipment and wiring. Returning to the subject of our study, approximately 30 of the 48 States mine coal. More than 20 of these States' produce coal in large quantities. How- ever, of the 30 States only four, 3 Pennsylvania, Utah, Washington, and West Virginia, have laws which specially call for the use of explosion-proof types

Jan 1, 1929

By P. G. Kovalchik

Safe electrical operation of shuttle cars depends upon maintaining the trailing cable's conductor temperature below 90° C. However, trailing cables are wound on and off reels, which changes the heat transfer characteristics of the cable-reel system. Derating factors for trailing cables are an attempt to adjust for this changing heat transfer mechanism in a practical way. The U.S. Bureau of Mines conducted research to determine acceptable derating factors for reeled mine trailing cables, using four cable-reel combinations, representative of industry usage. Cables were continuously and intermittently loaded at different duty cycles with direct currents of different magnitudes. Relationships between the average temperature rise and current load were established for each layer of each cable. Two models were constructed; one used empirical data from the continuous and intermittent load tests, and the other was based on thermodynamic theory. Results obtained from the theoretical model were compared with those from the empirical model for the rated temperature rise of the cable. Both models can be used to simulate a variety of test conditions including those that normally cannot be conducted in the laboratory. This information was used to determine acceptable derating factors for each layer of these cable-reel combinations.

Jan 1, 1994

By M. S. Seehra, R. S. Pandurangi

"Investigations of the infrared spectra of crystalline and amorphous silica particles of different sizes (0.05, 5, 10, 15, 30, 45, and 260 um) in the range of 400-4000 cm-1 using Fourier transform infrared/photoacoustic spectroscopy we reported. The change in the intensity I of the signal with porosity e of powders follows the e/(1 - e) dependence for strong bands and e dependence for weaker bands as pre¬dicted by the theory of McGovern of al. For strong bands, I also follows the empirical relation I ~ D-n, where D Is the particle diameter in cm and n = 0.34-0.42. The anomalous positive frequency dependence of I on the modulation fre¬quency f observed for the stronger bands in the 45-pm and 260-pm particles Is believed to result from saturation. Some observations on the effect of changing the background from (carbon black) powder to pellet are also made.INTRODUCTIONSince the publication of the Rosencwaig—Gersho (RG) theory on the photoacoustic effect in solids (1, 2), Fourier transform infrared/photoacoustic spectroscopy (FTIR/PAS) has become an important technique for obtaining the IR spectra of surfaces and materials in their natural state (1-12). In the one-dimensional RG theory, the incident radiation, modulated at frequency f, is absorbed by the material to a depth pp = 1/B (B = absorption coefficient), thus setting up temperature variations in the material. These variations heat the adjacent gas/solid interface leading to the pressure fluctuations of the gas above the sample, which in turn is detected by microphone as a PA signal. The thermal wave originating from no deeper than the thermal diffusion length(2k/npcf) 1/2 in the material contributes to the PA signal (here k, p, and c are respectively the thermal conductivity, density, and specific heat of the material). Since u2, can be varied by varying the experimental parameter f, depth pro¬filing by PAS is possible and a number of papers on this subject have appeared in recent years (2-10). Another im¬portant phenomenon is saturation which occurs when the material thickness 1> u> us (1-12).The original promise of PAS for use with powder samples, without the need to ""prepare"" samples as in FTIR spectros-copy, has not yet been fully realized because of several com¬plications. Theoretical works by Monchalin et al. (13) and McGovern et al (14) showed that the interstial gas in the voids of the powders can act as amplifier and that, for the same mass, a finer powder is expected to yield higher PA signal than a coarser powder. Although in a number of earlier studies (15-21) an increase of PA signal with decreasing particle size has been observed, a quantitative check on the equations developed by McGovern et al. (14) has not yet been made. It is necessary to understand the particle size effects in PAS if the promise of PAS for IR spectroscopy of powders is to be realized. In this paper, we report results of a detailed study on the PAS of silica powders for the particle size range of 0.05-260 um and compare the results with theory (14). We have also investigated the frequency dependence of the variousIR modes in these powders and show that the saturation phenomenon affects at least some of the observations. Some observations on the effects of pellet vs powder background are also reported (22-24). Details of these findings are presented and discussed in this paper."

Jan 1, 1990

By H. Polat, Q. Hu, S. Chander

"The collection efficiency of dust particles was determined in a laboratory dust chamber equipped with a water spray. Measurements were made in the presence of selected nonionic, cationic and anionic surfactants. For the nonionic and the anionic reagents, efficiency was maximum in a narrow range of concentration. The surfactant concentration corresponding to high collection efficiency was usually much below the commonly used concentration of l "", however. In comparison, much higher collection efficiency was observed for a cationic surfactant at extremely low concentrations. For delineating the mechanism of capture of dust particles, surface tension and contact angle results were used to obtain a correlation between the work of adhesion and the efficiency of collection. Such a correlation was reasonable for the nonionic surfactants but not for charged surfactants. In the latter case, electrostatic interactions between charged droplets and particles were more important, especially for the cationic reagent. INTRODUCTIONSeveral methods are used to control dust in mines. These include: ventilation, foam, scrubbers and sprays. This article is concerned with improving the effectiveness of water sprays, which are widely used to remove dust particles during continuous mining, by adding small quantities of surfactants. Water sprays produce small droplets which act as collectors of dust particles suspended in air. Sprays directed at the actual source of dust have the additional property of wetting the coal before the ·particles become airborne (Hamilton, 1974). Wetting agents, also called surfactants, arc known to play an important role in many applications where dust is a problem. However, conflicting reports exist in the literature with regard to the effectiveness of surfactants in water sprays (for a review, see Chander et al., 1988). In spite of the conflicting reports, the use of surfactants for dust control has increased over the years. In a recent study by the Bureau of Mines, a 27'6 reduction in respirable dust levels was observed in a mine test when surfactants were added to sprays (Foley, 1991)."

Mar 1, 1992

By Alla D. Mah

Heat content and entropy data at high temperatures were obtained for cuprous oxide (Cu2O) and cupric oxide (CuO). Experimental results and smooth values are reported. Equations are given for heat content increments and heat capacities above 2980 K. Low-temperature heat capacity data were obtained for cuprous oxide. Evaluation of the 2980 K entropy gave, S°298.15(Cu2O) = 22.08 ± 0.10 cal/deg mole. Heat of formation values were determined for cuprous and cupric oxides. The values are: AH°298.15(Cu2O) = -40,830 ± 300 cal/mole, and AH°298.15(CuO) = -37,230 ± 150 cal/mole.

Jan 1, 1967

By A. B. Hooker

A list of permissible mine equipment approved by the Bureau of Mines prior to January 1, 1940, was published as Information Circular 7207.3 Three supplements published as I. C. 7240,4 I. c. 7283,2/ and I. C. 73166/ completed the list of equipment available to January 1, 1945. The present list is a revision of the previous lists, together with the additional equip- ment approved from January 1, 1945, to January 1, 1947. In preparing this list, certain items have been omitted, either because the manufacturer is no longer in business or manufacture was discontinued several years ago. However, some discontinued equipments that are still in service and for which repair parts are available are marked with an asterisk to indicate their limited status. The remaining obsolete equipments are listed in tabular form in Appendix 1. Appendix 2 lists seven satisfactory fuels available for use in permissi- ble flame safety lamps and shows where the fuels are available. The equipments listed were approved only when inspection and tests showed that they met the minimum standards of safety as outlined in "schedules" based upon laboratory tests as well as on performance underground. This circular is published so that users and potential users may be in- formed of the many types of permissible equipment available for reducing hazards incidental to coal mining and as an aid in identifying the equipments.

Dec 1, 1947

By J. E. Hamak

This publication contains analyses and related source data for 151 natural gas samples from 19 States. Of the total samples, 138 were collected calendar year 1989. The remainder were collected earlier, but releases to were not received until 1989. All samples were obtained and analyzed as part of U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1990

By Robert E. Barieau

General expressions for evaluating various thermodynamic properties applicable to the van der Waals equation of state have been derived. These formulas were subsequently used to evaluate various thermodynamic functions in the two-phase region. The results indicate that, for a van der Waals fluid, there is a finite discontinuity in the second derivative of the vapor pressure curve, in the second derivative of the chemical potential or Gibbs free energy at the critical point, and in the heat capacity at constant volume measured at the critical density. Numerical values are tabulated and graphs are presented for all functions calculated.

Jan 1, 1967

By J. F. McIlwain

Cobalt-base hardfacing alloys used for wear resistance consist almost entirely of metals largely imported into the United States. As part of an overall research program to help alleviate this foreign dependency, the Bureau of Mines has been investigating an iron-base alloy system as a potential replacement for cobalt-base alloys for some uses. To ascertain the melting ranges, thermal analyses were made of cast heats of alloys containing, in weight percent, 59-61 Fe, 16-19 Cr, 8-9 Ni, 1 Mn, 1 W, 1 Mo, 0.5 Cb, 0.6 Si, 0.3 C, and 0-12 stoichiometric TiB2. Powder alloys within this range of composition, prepared by mechanical alloying, were sized and applied to mild steel test coupons by nontrans-ferred-arc plasma spraying. The resulting thin coatings were >95 pet dense, with bond strengths of 35 MPa and hardness of 400 to 840 DPH. Abrasive and adhesive wear test data were compared to those of a plasma-sprayed cobalt-base alloy. A range of boride contents resulting in most promising properties was determined for further research.

Jan 1, 1985

By W. J. Fene

It is often desired to obtain samples of air in places where collection by ordinary methods is not feasible, as in shafts amore means of descent or ascent are not provided, in sewer manholes, in gas or water wells, in empty oil tanks, and in sealed areas in mines. Heretofore, when such sampling was required, it was necessary to utilize the aspirating method, which was not always satisfactory; and to obtain samples of air in deep shafts, it was necessary to use long sections of rubber tubing, which was not always available. DESCRIPTION OF NEW DEVICE A new method or "device" employs a common snap-type mousetrap to break the neck of a vacuum tube at the place where it is desired to collect the sample (see fig. 1). A mousetrap is mounted on one end of a block of wood 11-3/4 by 3 by 3/4 inches in such camper that a lead weight attached to the trigger hall spring the trap when the device is given a sharp jerk. A vacuum tube is placed on the other end of the block and held in place by a strong rubber band. A strip of corrugated rubber is placed on each side of the grooved block to prevent the tube from clipping when the sample is taken. An adjustable shoulder, provided with a rubber cap, is pieced se that the neck of the vacuum tube will rest on it. The shoulder is made adjustable to accommodate various sizes of tubas and to keep the neck of the tube from breaking tee far back from the point. A metal handle is fastened to one end of the block, with a hole in the end through which the brass wire used for lowering the device is tied. The device is enclosed by a strong wire-gauge covering, hinged on one side and so arranged that it can be locked shut on the other side. This covering prevent: breaking of the tube while it is being lowered or raised in a shaft or other place. Brass wire of not less than 22 gage should be used for lowering the device. A detailed drawing of the device is shown in figure 2.

Jan 1, 1940

By Steven M. Shope

An essential element of the Bureau of Mines electromagnetic location and communication system for trapped miners is a quantitative knowledge of the surface and above-surface electromagnetic fields created by an underground transmitter. The field solutions given in this report use approximations in which the displacement currents are negligible for low frequencies. The earth is represented by a homogeneous half-space model in which a dipole source is immersed. The vertical magnetic field equipotential contours at and above the surface are graphically mapped. The volumes of the regions bounded by these contours are directly related to the geometrical zones of signal detectability. Knowledge of the detectability zones will enable the proper search strategies to be developed for airborne detection of trapped miners.

Jan 1, 1983

By D. Harrington, M. W. Von Bernewitz

Sections 120 and 121 of Article XI. Fire Control, of a proposed Mine Safety Law in preparation, to be used as desired and when approved by any State, contains these provisions: After the adoption of these regulations, no mine operator shall erect any nonfireproof structure within 50 feet of any mine entrance. or airway. Every operating mine having nonfireproof structures within 50 feet of any mine entrance or airway, except headframes necessary for hoisting, shall have such structures fireproofed or removed and replaced with fireproof structures within six months of the adoption of these regulations. Before reopening, mines idle at the time of the adoption of these regulations shall have all non- fireproof structures fireproofed, removed, or replaced with fire- proof structures as required by the foregoing sentence. Upon receipt of the written statement of a mine operator that the fireproofing of existing structures is impracticable, the chief mining engineer (of the State commission) shall satisfy himself as to the abouracy of the statement. If he concurs that fireproofing is impracticable, and if at the same time he holds the opinion that adequate protection can be provided otherwise by such procedure, he shall have authority to issue a written permit for the substitution of fireproof door at or near portals of mine openings and collars: of shafts. Such doors shall fit as nearly gas-tight as possible. and shall be installed in such a way that the mouths of mine open- ings can be closed readily from outside of structures. The effec- tiveness of such permit may be made contingent upon the operator's continued compliance with any additional precautions which are necessary in the chief mining engineer's opinion to protect the lives of miners.

Mar 1, 1932

By Ronald S. Conti

This U.S. Bureau of Mines report discusses the results of research conducted in the Bureau's experimental mine at Lake Lynn Laboratory on the response of fire sensors to simulated mine fires, which included (1) a slowly developing coal-conveyor belt fire, (2) a rapidly burning liquid fuel-belt fire, and (3) a liquid fuel-belt fire in the presence of diesel exhaust. During these tests, several mine fire sensors were evaluated with respect to sensor placement, spacing, and type. The data indicate that smoke sensors alarm several minutes before CO sensors do; and that, in the presence of diesel exhaust, a prototype diesel-discriminating smoke sensor can successfully function without being sensitive to the diesel contaminants. The vertical placement of sensors in the entry near the fire was also shown to be critical in terms of alarm times. Additional data showed that variations exist in response time and level of response for two brands of electrochemical CO sensor. Results also indicate that early detection of fires will improve the probability of miners' escape, because of reduced smoke concentrations during the incipient stages of the fire.

Jan 1, 2010

By Wallace W. Roepke

Research on coal cutting at the Bureau of Mines Twin Cities Research Center (TCRC) has evolved from a purely mechanical approach, specifically to reduce dust or frictional methane ignitions, into an understanding of the complexity of the cutting system relationships. Achieving an understanding of these relationships requires a wide variety of testing techniques and equipment. Laboratory facilities and the associated equipment exist for shallow to deep cutting in both coal and coal-inclusive rock with any desired bit type. Research efforts with this equipment are providing insight for significant advances to help solve the problems of pneumoconiosis and frictional ignition. This effort will ultimately affect both respirable dust and methane ignitions at the face through better bit design and will increase the salable percent of run-of-mine (ROM) coal processed. It will also affect the design of rotary-drum cutting continuous mining machines (CMM) and longwall machines. This report describes the main features of the coal cutting research facilities at TCRC.

Jan 1, 1983

By Joseph S. Coffman

To determine the availability of manganese for metallurgical purposes from selected world resources, the Bureau of Mines evaluated the potential production of contained manganese in concentrates based on the demonstrated resources of 23 foreign and 8 domestic mines and deposits in 9 market economy countries. All but 2 of the 23 foreign deposits are operating mines; none of the domestic deposits are in operation. The demonstrated resources of the mines and deposits used in this study represent an in situ ore resource of approximately 2.2 billion tons," containing 780 million tons of manganese with a total recoverable production potential of 514 million tons of contained manganese in concentrates. The analyses of mines and deposits in this study indicate that about 213 million tons of the contained manganese (41 pct) is potentially available at a January 1981 constant dollar long-run total cost of up to $1.50 per long ton unit (22.4 lb, or 10.15 kg contained Mn), approximately 428 million tons (83 pet) is potentially available at a cost of about $1.75 or less, and 491 million tons (95 pet) is available at less than $3.30. The remaining 23 million tons, which is potentially available at much higher costs (about $8 to $35 per unit), represents the U.S. deposits. On an annual basis, with a cost range of up to $1.75 per long ton unit, the availability from currently operating mines would last at least 80 years based on 1980 world production data. Total manganese production costs are estimated to comprise mining-8 pet, beneficiation-3 pet, transportation-26 pet, and smelting-63 pet.

Jan 1, 1984