Search Documents

By George S. Rice, C. W. Owings

"Brattice cloth is an important material in coal-mine ventilation practically all coal mines use some brattice cloth, gassy mines a large amount. It is employed in three ways:Crosscut brattices.Curtains in haulageways.Line brattices in gassy mines.In each case brattice cloth is used to deflect part or all of a split of the mine ventilating current into or toward the face of a working place. As a general rule, its use in a particular location is temporary.A crosscut brattice should be employed only until a permanent stopping has been erected. Such a brattice is subject to little wear when in actual service, the chief damage occurring when it is taken down and put up again.When used for curtains on haulageways or haulage crosscuts to deflect the air current up into rooms or headings, the wear on brattice cloth is considerable, as mine cars, machines, and personnel constantly pass under the curtains which last only a few days or a few weeks in an active part of the mine. For such purposes tightly woven smooth cloth is desirable, so that it will not be easily torn. Curtains should not be used back from the working places, as they sometimes are, to deflect the main. split, as the leakage of air is too great. Doors should be used in such places."

May 1, 1928

"The following articles were produced through funding under Generic Mineral Technology Center for Respirable Dust research. Full articles appear in the proceedings, 3rd Symposium in the Mineral Industries, published in 1991 by the Society for Mining, Metallurgy and Exploration, Inc.Personal Diesel Exhaust Aerosol SamplerV.A. Marple, K.L. Rubow, and Y. TaoParticle Technology, Mechanical Engineering Department, University of Minnesota, Minneapolis, Minnesota(Section ill. Diesel I: Diesel Particulate Measurement, pp. 73-81)Abstract. Techniques are being developed for measuring the mass concentration of respirable diesel exhaust particles found in underground coal mines. Studies have been conducted over the past five years to investigate size selective 18Dlpling techniques to measure the respirable mass concentrations of diesel exhaust and mine dust aerosol particles in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler.Three personal diesel exhaust aerosol samplers have subsequently been designed and evaluated in both laboratory and field settings. These samplers use size selective classifiers for the determination of respirable mass concentrations of mineral dust and diesel exhaust particles. Their designs are based on the premise that diesel exhaust particles are predominantly less than 0.8 µm while mineral dust is greater than 0.8 µm.One design, selected for field evaluation, consists of a 10 mm nylon respirable dust cyclone followed by a 0.8 µm cutpoint impactor and afterfilter. The cyclone removes the nonrespirable particles while the inertial impactor state, collects the mineral dust on an impaction plate and allows the diesel particles to penetrate to an afterfilter. The two sample fractions of the respirable particles ( <0.8 µ.m and >0.8 µm) are gravimetrically analyzed to determine the concentrations of the diesel and mineral dust portions in the respirable coal mine aerosol."

Mar 1, 1992

By David R. Hanson

Transient electrical noise events pose serious problems for data acquisition systems used in monitoring acoustic emissions in laboratory and field environments. The U.S. Bureau of Mines has designed and constructed a trigger discriminator circuit for use in ultrasonic acoustic emission studies. Designed for use with signals in the frequency range of 50 to 400 kHz, the instrument examines .incoming signals for frequency content, amplitude, simultaneity, threshold crossings, and number of channels above threshold. If preselected criteria on these properties are met, a plus 5-V pulse is output that may be used to trigger a data acquisition system, allowing rejection of noise events that do not possess useful information. The system was designed for four input channels, but may be expanded to more channels with minimal design changes.

Jan 1, 1995

By K. E. Tame

An alkaline leaching procedure for recovering uranium from a submarginal 0.1 percent Ug Og calcareous carnotite ore from the Shiprock , N. Mex . , area was investigated . A recovery of 72 percent of the uranium was attained in a preliminary test embodying the commonly accepted practice of ( 1 ) alkaline leaching at 90° C , ( 2 ) multiple stage filtration and washing for recovery of a clear pregnant solution , and ( 3 ) caustic precipitation of uranium as sodium diuranate , with recycle of the barren solution to the leaching and washing circuits . Ion exchange resins were used in a second , less orthodox test that comprised ( 1 ) sodium carbonate leaching of minus 10- mesh ore at 90 ° C to dissolve the uranium , ( 2 ) filtration to recover the leaching reagent for reuse , (3 ) recovery of the uranium- bearing solution in the filter cake as a pregnant slime slurry by repulping of the filter cake followed by a sand- slime separation and countercurrent decantation (CCD ) washing for rejection of the sand fraction , (4 ) recovery of the dissolved uranium from the pregnant slime slurry by resin- in- pulp (RIP ) , ( 5 ) elution of the uranium from the resin with a solution of ammonium chloride acidified with hydrochloric acid , and (6 ) precipitation of the uranium with ammonia gas . About 83 percent of the uranium was extracted from the ore and 95.5 percent of the dissolved uranium recovered by ion exchange . Improved laboratory results were obtained using the RIP process , but larger scale tests would be necessary for economic evaluation of the two processes .

Jan 1, 1964

To provide longwall operators with a method to predict methane emissions from panels with increased face width.

Jan 1, 1997

By Leonard Obert

A triaxial procedure is described for measuring the modulus of elasticity and Possion's ratio of stress relief cores , that is , the concentric hole cores obtained by the overcoring technique . The elastic constant determinations can be made at stress levels comparable with those encountered in underground mining . The results from tests on an aluminum alloy calibration specimen and four rock specimens are included .

Jan 1, 1964

By H. E. Powell

This Bureau of Mines study describes two processes for recovering zinc, copper, silver, and iron from the magnetic fraction of a waste generated by the primary smelting of zinc in horizontal retort distillation furnaces. The laboratory-scale procedures include reduction melting to produce a high-copper iron and matte smelting to produce a copper-silver-iron matte and metallic iron. Zinc is fumed in each process and recovered as the oxide. Direct reduction melting yields a metallic iron high in copper and a small rich matte from the sulfur contained in the waste. The products of the second process are a matte containing essentially all of the silver, about 80 pct of the copper and 37 pet of the iron, and an iron-copper alloy containing all of the remaining copper. Extraction with metallic lead or sodium sulfate recovers essentially all of the copper from the molten high-copper iron and yields an acceptable foundry iron.

Jan 1, 1973

By K. K. Kershner

Nickel having a purity of more than 99.99 percent with reference to metallic impurities was electrodeposited at the Rolla Metallurgy Research Center of the Federal Bureau of Mines. The production of high-purity nickel is in keeping with the current trend in technologies for producing metals with lower and lower percentages of impurities. To understand more fully the role to be played by nickel by itself and as a component in many alloys, the element must be in a state of high purity. Procedures are outlined for purifying nickel solutions by precipitating and filtering off impurities. Details are given for using the purified solutions as electrolytes in depositing high-purity nickel. The elecneleposited nickel contained 0.0005 to 0.002 percent each of cobalt, copper, aid iron together with spectrographically detectable traces of aluminum, magnesium, and silicon. The deposits were smooth and dense; the crystalline structure was typical of an electrodeposited metal. Some preliminary experiments for purifying nickel solutions by liquid-liquid extraction are also described in this report. Tests of this type were limited since more encouraging results were obtained by other methods of purification.

Jan 1, 1961

By Gerald W. Elger

The Federal Bureau of Mines developed a modification in the conventional Kroll process for preparing high - purity hafnium metal . This modification involved the partial replacement of magnesium by sodium in the batch reduction of purified hafnium tetrachloride to sponge metal . The raw tetrachloride was purified either by thermal degassing of the volatile contaminants to the atmosphere or by fused- salt treatment . In the fused- salt treatment , the tetrachloride was contacted with molten alkali chlorides to remove the impurities . The reaction byproducts were removed from the metal by heat treatment in an evacuated furnace . The metal sponge was consolidated by melting into buttons or ingots , which were analyzed for impurities . The purity of the metal prepared by the modified process is superior to that of the metal produced by the conventional method . The hafnium metal was comparable to crystal - bar hafnium except for the oxygen content , despite the abnormally high impurity concentrations in the raw tetrachloride . Several ingots were successfully cold - rolled to sheet .

Jul 1, 1960

By David S. Yantek

A-weighted sound levels around vibrating screens in coal preparation plants often exceed 90 dB(A). The National Institute for Occupational Safety and Health (NIOSH) is actively developing noise controls to reduce noise generated by horizontal vibrating screens. A 121-microphone, 3.5-meter-diameter array was used to perform beamforming to determine locations of significant noise radiation on the screen. Below about 1 kHz, the screen body was found to be the most significant noise source. The beamforming contour maps showed several key locations on the sides of the screen and the feedbox are the most significant contributors. Operating deflection shape (ODS) analysis was used to examine the screen behavior under actual operating conditions. This information is helpful in determining how to modify the screen body to reduce the noise radiated by the screen below 1 kHz. The analysis showed modal vibration patterns on the sides and feed box were the main contributors to noise. The results show several areas on the screen sides and feedbox that can be modified to reduce noise.

Jan 1, 2009

By R. Hogg

"The basic population balance models for agglomeration processes are reviewed and procedures are described for extending their applicability to systems with size-dependent rate constants and to the formation and growth of porous agglomerates from rigid, solid-particles. Simplified procedures for the further extension of the models to include simultaneous agglomerate growth and breakage are also described.INTRODUCTION The association of small particles into clusters or agglomerates is a significant factor in many facets of particle processing. Agglomeration processes are widely used to facilitate handling, storage and utilization of fine powders. Processes such as coagulation or flocculation are used to aid solid-fluid separation in dispersed particulate systems. Agglomeration also occurs as an accompaniment, often unwanted, to other particulate processing operations such as fine grinding, mixing and blending, transport and flow.Reliable agglomeration models are needed for improved understanding of the processes in general and of the complex role of numerous, interacting variables as well as for direct application to the design and control of industrial processes such as flocculation, granulation and pelletization. Ideally, the models should account for the primary forces responsible for agglomerate formation and growth, the effects of external forces on process dynamics, the development of agglomerate structure and its role in the process itself, and the effects of concurrent processes such as structure modification (e.g. compaction) and agglomerate breakage or degradation."

Jan 1, 1989

By Elton L. Litchfield, Milton L. Weiss

Studies were made on the projectile impact sensitivity of explosives by subjecting explosive samples to the impact of metal projectiles fired from a 0.50- caliber gun . The projectiles , in the form of right cylinders , made plane surface to plane surface contact with the explosives . Pressures in the explosive were investigated with an expendable pressure transducer in some instances . The physical model of the projectile - explosive interaction describes , in principle , the duration of the peak shock pressure in terms of the projectile and explosive geometry and the steady- state penetration of the explosive . Of the explosives studied , liquid hydrogen- solid oxygen and liquid oxygen - solid or liquid hydrocarbon fuel were the most shock sensitive ( requiring an initiating shock of about 1.0 kb or 987 atmospheres pressure ) ; cast TNT was the least sensitive ( requiring an initiating shock of more than 110 kb pressure ) . Measurements of pressure in the explosive showed some moderate space resolution by the transducer and gave pressure distributions in agreement with expectations from the model of the shock processes . The appearance of the recovered projectiles and the calculated initiation shock pressures suggest that the solid explosives were initiated directly to high- order detonation , whereas the liquid explosives were probably initiated to low- order detonation-- with a subsequent , later transition to high- order detonation .

Jan 1, 1965

By T. C. Phalen

"Necessary Qualities There mines are located in out of the way places, where timber is scarce and its price high, the problem of protecting it from fire risk is of considerable practical importance. Scarcity of timber for mining purposes is commonly met with in the more arid parts of the country, where, also, mine timbers are most likely to become dry, and inflammable, and where, therefore, the risk from fire is accentuated. Any effective and cheap method of securing adequate protection of such timber at the lowest possible cost is worthy of careful investigation. The use of magnesite cement has been suggested in this connection.The necessary qualities for any substance for the use suggested above may be summarized as follows: It should be resistant to abrasion, and to impact and structural stresses. It should be durable when subjected to the action of the ele¬ments, and stable to any minor derangements of the base on which it is placed. It must be relatively unaffected by changes in temperature, by the action of water, and should adhere to the material on which it is placed, and it should also be free from shrinkage cracks due to setting up the material, Magnesite cement appears to fulfill the various conditions outlined above.The elasticity of such cement is the outstanding quality which makes it desirable for exterior work. It also possesses the ability to adhere to all materials in a marked degree. Its freedom from expansion and contraction after setting is one of the principal reasons for its adhesive quality. It may be applied to old brick or stone walls, even tho they have been repeatedly covered with paint, and the quality of ad-hearing to wood makes it possible to secure a weather-proof protection to the wooden casings and trim of exterior openings. The quality of adhesion and elasticity is easily proved by applying a 1/2"" layer to a 1"" board which has been first covered with metal lath. Such a board, about 8 feet long, may be repeatedly deflected about 3"" in the center without breaking the bond to the board, or causing any cracks to appear in the magnesia cement. The ability to resist fire as well as the possession of insulating qualities are also desirable characteristics of magnesia cement stucco."

Dec 1, 1919

By C. L. Chaney

Investigations were conducted to develop spectrochemical methods capable of determining 0.01 to 100 micrograms of metals in 50 milliliters of solution. The use of gallium hydroxide (Ga(OH)3) as a carrier-precipitant to concentrate metallic ions is described. A porous-cup graphite electrode is used to collect the precipitate. A specially designed plunger permits the electrode assembly to serve as the sample-containing electrode in the subsequent spec-trographic analysis. Analytical curves are presented for antimony, arsenic, beryllium, and zinc. Sensitivities of detection are given for 13 elements. The techniques were applied to identify impurities separated from tungsten, to determine trace impurities in solutions containing high concentrations of magnesium, cobalt, or nickel, and to identify trace impurities in hydrofluoric acid. Laboratory glassware was a serious source of contamination when low levels of zinc were determined.

Jan 1, 1963

By J. O. Winget

Phosphonic acid and iminodiacetic acid chelating resins were investigated to assess their potential as selective ion exchangers for separating lanthanide elements and yttrium . The affinity of phosphonic acid resin for lanthanides increases with increasing atomic number , and that of iminodiacetic acid resin for lanthanides increases with atomic number to a maximum for element 62 and then declines with atomic number throughout the remainder of the series . Elution sequences of the elements with mineral acid eluants corresponded favorably with equilibrium data , whereas the elution sequence obtained with chelating eluants was proportional to the relative values of the stability constants of the chelating agents with the lanthanides . Separation of lanthanide mixtures into groups of light and heavy elements with iminodiacetic acid resin appears feasible .

Jan 1, 1964

By Charles L. Parsons, R. B. Moore, S. C. Lind, O. C. SCHAEFER

Early in 1912, from information received by the Bureau of Mines, it became evident that quantities of valuable radium-bearing ore from Colorado were being exported for manufacture in foreign coun- trics and that at least part of the manufactured product was being returned to this country and sold at a price entirely incommensurate with that received by the miner and the prospector. Consequently, in line with its efforts to increase efficiency in the mining and treat- ment of mineral resources, the Bureau of Mines undertook an inves- tigation of conditions. Results of this preliminary investigation were published, in the summer of 1913, as Bulletin 70, which gave an out- line of the radium deposits of the West, the conditions of mining, the wastes involved, and the status of the production of radium from its ores. At about this time newspapers and medical journals were publish- ing statements regarding the value of radium in cancer therapy. These reports, although many of them were exaggerated, brought out clearly the remarkable virtue of the gamma rays for the treat- ment of cancer and other malignant growths. In view of the fact that the largest known supplies of radium ore in the world are in the States of Colorado and Utah and on the public lands of the United States, it was deemed highly important for the Bureau of Mines to study the production of radium in detail. Such study, it was hoped, would enable the prospector and miner to obtain a fairer price for the ores and would furnish information necessary in case Congress appropriated funds to develop methods for extracting radium from ore on the public lands under Government supervision, to be supplied at cost to the hospitals of the Army, Navy, and Public Health Service.

Jan 1, 1915

By R. C. Hickman

"INTRODUCTION The most productive area of the eastern Virginia pyrite belt lies to the north of the village of Mineral., in Louisa County. The largest producers of pyrite ore in the area were the Armenius, Boyd Smith, and the Sulphur mines.The Boyd Smith mine started production about 1890 and operated more or less continuously until 1922, when competition from the Gulf States and Spain closed the pyrite mines in Virginia. There are no reliable records of production or value of minerals produced.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the most effective utilization of our mineral resources to the end that they take the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Palston, chief, analyzes samples and performs beneficiation tests.The project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch, Bureau of Mines.LOCATIONThe Boyd Smith property is reached from Mineral, Va., by traveling north on State Route 522 about 2-1/2 miles. An unsurfaced road, winding in a northwesterly direction, loads to the Boyd Smith headframe, which is about half a mile from State Route 522 (fig. 1). The tract comprises 181 acres."

Aug 1, 1947

"There mines are located in out of the way places, where timber is scarce and its price high, the problem of protecting it from fire risk is of considerable practical importance. Scarcity of timber for mining purposes is commonly met with in the more arid parts of the country, where, so, mine timbers are most likely to become dry, and inflammable, and where, therefore, the risk from fire is accentuated. Any effective and cheap method of securing adequate protection of such timber at the lowest possible cost is worthy of careful investigation. The use of magnesite cement has been suggested in this connection.The necessary qualities for any substance for the use suggested above may be summarized as follows: It should be resistant to abrasion, and to impact and structural stresses. It should be durable when subjected to the action of the elements, and stable to any minor derangements of the base on which it is placed. It must be relatively unaffected by changes in temperature, by the action of water, and should adhere to the material on which it is placed, and it should also be free from shrinkage cracks due to setting up the material, Magnesite cement appears to fulfill the various conditions outlined above.The elasticity of such cement is the outstanding quality which makes it desirable for exterior work. It also possesses the ability to adhere to all materials in a marked degree. Its freedom from expansion and contraction after setting is one of the principal reasons for its adhesive quality. It may be applied to old brick or stone walls, even tho they have been repeatedly covered with paint, and the quality of adhearing to wood makes it possible to secure a weather-proof protection to the wooden casings and trim of exterior openings. The quality of adhesion and elasticity is easily proved by applying a 1/2"" layer to a 1"" board which has been first covered with metal lath. Such a board, about 8 feet long, may be repeatedly deflected about 3"" in the center without breaking the bond to the board, or causing any cracks to appear in the magnesia cement. The ability to resist fire as well as the possession of insulating qualities are also desirable characteristics of magnesia cement stucco.Magnesite cement stucco should be applied in two coats, each 1/4"" thick on various surfaces such as wood lath, metal lath, sheathing board, brick, hollow tile, or stone; care being taken as regards the presence of lime, unless the same has been rendered, or become inert as with very old, walls. The first coat made up to a consistency that works easily under the trowel is applied in the usual manner. No water should be added to the liquid chloride as it would alter its density, and injure the work. The second or finishing coat is then applied. The aggregates are different in each, and no other dry material should be added to them as they come to the trade. The cement may be applied in zero weather without damage. Setting is quite slow under such conditions, but the cement ultimately becomes hard. It should always be applied to a dry surface excepting that under certain conditions it is desirable to apply a solution of magnesium chloride before using the stucco."

Dec 1, 1919

By Franxis Church Lincoln

"INTRODUCTION During September 1944, the Bureau of Mines undertook a program of investigation and limited exploratory drilling at the Last Chance mine, near the village of Arthur in Grant County, Wisconsin, as part of a general investigation of the zinc-producing area of southwestern Wisconsin when every effort was being made to increase the production of metals important to the Nation's war program.The Bureau's attention was directed, to the Last Chance mine when the operators discovered high percentages of zinc in an exploratory churn drill hole a short distance southeast of the mine. The ore was found in the Trenton Limestone, which underlies the ore horizon then being mined. To determine whether this discovery was important, and to demonstrate the possible extension of the ore the Bureau of Mines drilled five additional holes in the vicinity of the discovery.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Nines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report."

Mar 1, 1947

By R. V. Ramani, R. L. Frantz

"The U.S. Bureau of Mines (USBM) established on August 15, 1983, a Generic Mineral Technology Center (GTC) for Respirable Dust within the Mining and Mineral Resources Research Institutes (MRls) at The Pennsylvania State University (PSU) and West Virginia University (WVU) in association with participating MRis at Massachusetts Institute of Technology (MIT) and the University of Minnesota (UMN). The primary goal of the Center is to reduce the incidence and severity of respirable dust disease through researching and advancing the fundamental understanding of all aspects of respirable ~~9t associated with mining and milling and the interaction of dust and lungs. Other Center activities include the training of engineers and scientists, graduate students and undergraduate students through their respective institutions, and the technology transfer to the industry. The Center also serves as the reference center for publications in the respirable dust area. IntroductionExposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic effects and some others, slow and long enduring consequences, has been a major concern for labor, management and government alike. This concern has manifested itself in four primary mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of mines according to the best recommended practices, (3) interaction of dust and lung control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workmen's compensation laws for occupation related health deterioration.The stated objective of the Federal Mine Safety and Health laws is to"" permit each miner the opportunity to work underground during the period of his entire adult working life without incurring any disability from pneumoconiosis or any other occupation-related disease ."" Significant progress has been made in lowering the dust levels in mines since the inception of the Bureau's respirable dust research program. It is generally agreed that mines are less dusty today than they were a decade ago. However, the most serious hazard for workers in the mining and minerals processing industries is still the exposure to respirable dust, and solutions to the problem of respirable dust disease remain to be found."

Mar 1, 1989