Search Documents

By B. J. Dalton

The Bureau of Mines Helium Research Center has developed a computer program for solving two-phase equilibria data for binary mixtures and for evaluating thermodynamic functions of interest, including all critical points. This computer program was used to calculate equilibrium points on the PVTu surface for the helium-nitrogen system as predicted by the Van der Waals equation of state. Numerical values are tabulated and illustrations are presented for 1,279 equilibrium points and for quantities needed to construct Ponchon diagrams. Equilibrium ratios as a function of pressure at constant temperature and of temperature at constant pressure-are also shown graphically. In addition, saturated partial molal volume and partial molal enthalpy data are given. It is shown that the Van der Waals helium-nitrogen system exhibits retro-grade condensation of the second type for liquid helium concentrations of about 0.07 mole fraction or less and pressures below about 45 atm. It is also shown that the critical point is at a -maximum value of pressure (at constant temperature) and of temperature (at constant pressure).

Jan 1, 1971

By V. E. Edlund

As part of its efforts to devise new and improved methods for recovering lithium from unconventional resources , the Bureau of Mines investigated a lime -gypsum- roast , water- leach technique for processing lithiumenriched ( 0.01-0.68 pct Li ) clays . This report presents the results of a study of the technical feasibility of extracting lithium from raw material representative of clay beds associated with the McDermitt Caldera complex in Nevada and Oregon . prepared from water used Pellets suitable for bench-scale roasting studies were mixtures of minus 200 -mesh clay , limestone , and gypsum , with as the pelletizing agent . Roasting pelletized charges at 900 ° to 1,000° C temperatures for 1- to 4-h periods produced calcines that leached readily , yielding water - soluble lithium sulfate ( Li₂SO4 ) . A 5-3-3 ( weight ratio ) mix of clay , limestone , and gypsum produced calcines with the best leaching characteristics . More than 91 pct of the contained lithium was extracted from pelletized mix batches roasted in covered refractory boats . Lithium recovery decreased to about 87 pct when the mix was roasted under dynamic conditions in a gas - fired rotary furnace . A reaction mechanism was postulated which indicated that dilution and loss of SO2 and oxygen in the combustion exhaust adversely affected the leachability of the dynamically roasted calcine .

Jan 1, 1983

By R. M. Santmyers

Umber and sienna, like ocher, are naturally occurring mineral pig- ments composed largely of clay permeated with hydrated iron (ferric oxide), but they differ from ocher in that they also contain hydrated manganese oxide. The presence of manganese accounts for their browner color. In addition to silica and alumina (clay) and the coloring oxides of iron and manganese, these pigments often contain lime, barium, and other metallic salts as impurities. Sienna most nearly approaches ocher in chemical composition, and the chief distinction is its physical character. It grades into ocher with de- creasing iron content and into umber with increasing manganese content. Sienna is translucent rather than opaque and is more of a stain than a pigment; as the iron oxide content is rather high (often 60 to 80 per cent), the color is strong and rich and varies from pure brown to reddish brown. This pigment raw sienna, terra di Siena, and Italian earth. is known under several names: Burnt sienna is a pigment of an orange-brown tint made by cautionsly calcining raw sienna. It is divided into two grades; American, and Italian burnt sienna. American burnt sienna is a reddish-brown pigment containing from 25 to 60 per cent iron oxide (Fe2O3). One grade, found in Pennsylvania, analyses as high as 80 per cent and is mown as double strength sienna. Italian burnt sienna is a pigment generally containing more iron than the American product, averaging 60 to 75 per cent iron oxide.3 American pig- ments of the same iron content differ materially in shade, having a Havana- brown color, whereas the Italian is more of a maroon. Italian siennas when tinted with 20 per cent of white, show a bluish tint, whereas American siennas yield a brownish or yellowish hue. Raw umber, also known as Turkey umber, Levant umber, and terra ombra, is a greenish to yellowish brown siliceous and ferruginous earth, containing a considerable proportion of one or other of the higher oxides of manganese, Mng04 and MnO2." It is similar in many respects to raw sienna except that it is much coarser and contains more manganese oxide. All umbers contain over 5 per cent of manganese dioxide. Like sienna, umber is a permanent pigment, not being injured by light or by impure atmospheres. Burnt umber (velvet brown, chestnut brown, etc.), results from the calcination of raw umber. The color is much richer and warmer than that of the raw umber. The colors are equally permanent and can be used in conjunc- tion with all other durable pigments.

Sep 1, 1931

By T. E. Green, E. F. Spano, W. J. Campbell

A combined ion exchange X- ray spectrographic method was evaluated for the determination of 11 metallic elements in high - purity tungsten : Aluminum , calcium , chromium , cobalt , copper , iron , magnesium , manganese , nickel , titanium , and zinc . Copper , nickel , and manganese in the 5- to 100 - microgram range ( 1 to 20 parts per million based on 5 - gram samples of tungsten ) , calcium in the 10- to 100 - microgram range , and cobalt in the 5- to 20 - microgram range can be determined within an accuracy of ± 10 percent of the amount present . Limits of detection of these elements are 0.05 to 0.14 microgram . The overall method was unsatisfactory for the determination of aluminum , chromium , iron , magnesium , titanium and zinc in tungsten .

Jan 1, 1964

By D. W. Butner

The blast -hole method for drilling and breaking ground is not new to the mining industry . For several years it has been used rather extensively in Canada , particularly in the gold mines , where it was first developed and where the major advances in the technique as applied to present - day mining problems have been made . At present , 40 mines in Canada and the United States are using the method in one form or another , and from all indications its use will increase in the future . In two California mines , blast -hole diamond drilling is now used for a part of or for all stoping operations , and in one of these it is used to some extent in development work . At the Mountain Copper Co.'s Hornet mine in Shasta County, about 50 percent of the pyritic sulfide ore produced is mined by the blast - hole method , and the U. S. Vanadium Corp. mines 80 percent of the ore produced at its Pine Creek tungsten mine in Inyo County by this method . At Pine Creek , long -hole drilling and blasting is used for mining pillars also , and in pre - stoping development . The blast -hole diamond - drilling method is not applicable to all types of ore bodies . A third property in California , the El Dorado Limestone Company , El Dorado County, tried the method for several months in 1943 and 1944 , but , owing to certain factors that greatly increased mining cost , the company soon returned to conventional mining methods .

Feb 1, 1948

By James H. Russell

Alkalized alumina (an active form of sodium aluminate) has been considered as a sorbent for the removal of sulfur dioxide from industrial flue gases. Four rate equations, each based on a different mechanism, were compared with the results of thin-bed sorption tests. It was found that each equation agreed with the experimental results, within experimental variance, over most of the range of sorption studied. First-order rate equations were generally satisfactory in explaining both sorption and regeneration. It is concluded that the equations developed are adequate for the design of commercial fluidized beds for the sorption of SO2 from industrial flue gases and regeneration of the alkalized alumina.

Jan 1, 1970

By H. R. Shell

Of three known compounds in the ternary system K20 - PbO - SiO2, one having the composition K2Pb4Si8021 crystallizes into a structure with asbestiform properties. This compound, whose silicon-oxygen ratio is between that of the layer silicates (for example, mica) and the double-chain amphiboles, crystallizes in the tetragonal system. It malts, apparently congruently, at 779° C. The fiberized product prepared from crystals is fluffy and closely resembles natural asbestos in appearance, but is more brittle and has less strength. However, potassium-lead silicate may be separated into fibers with a uniform diameter of 200-300 A.U., and the fibers show with the electron microscope the s criteria that have been interpreted as indicating a hollow tube structure in chrysotile asbestos. Since very few inorganic crystalline compounds have such a structure, the material has unusual scientific interest. Microcrystalline potassium-lead silicate was rapidly and completely formed when powdered glass of the same composition was heated to 650° - 700° C, but macrocrystals grew only slowly from the viscous massive glass. Maximum growth rate was 0.12mm. per hour at 700° C.

Jan 1, 1957

By William R. Wayment, David E. Nicholson

A modified percolation - rate test is proposed for use in determining flow rates through hydraulic backfill ; in contrast to the conventional test , a percolation- rate versus void - ratio relationship is established . requirements and a detailed test procedure are described . Equipment Results of a conventional test are compared with those of the proposed modified test . The proposed modified test method yields more accurate , realistic , and usable percolation- rate ( permeability ) data . The significance of obtaining accurate percolation rates for use in analyzing waterflow through hydraulic backfill is discussed .

Jan 1, 1964

By H. L. Riley, B. W. Gandrud

"INTRODUCTION AND SUMMARYIn connection with a program of research work on coal at its Southern Experiment Station, the Bureau of Mines, in cooperation with the University of Alabama, conducts washability studies of samples of coal from coal fields in Alabama and other Southern States in which commercially important deposits of coal occur. The first such study on coal from a bed in the Arkansas field has been completed, and the results are presented in this report.One of the main objectives of a washability study is to obtain technically and commercially important data in connection with the best methods for preparing and utilizing the Nation's limited reserves of good coking coal. Such information is important from the standpoint of conservation in that it facilitates selection of preparation methods that will yield a good grade of coking coal with a minimum of losses of coal in the rejects.The coal on which this report is based was obtained by underground and tipple sampling at the quality mine of the Quality Excelsior Coal Co. about 3 miles east of Hackett, Ark. This mine operates in the Upper Hartshorne bed, which, as the main source of coal in what is known as the Hackett-Excelsior district, yields an excellent grade of low-volatile coking coal, which is marketed at steel plants in Colorado and California. Production from this bed by the major producers in the Hackett Excelsior district was at the rate of about 125,760 tons annually in 1949, according to the Keystone Coal Buyers Manual. 2/In the laboratory, the tipple sample was crushed to 6-inch top size and screened on a 2-inch round-hole screen. The 2-inch to 0 undersize, amounting to 71.4 percent of the total sample, was fractionated into a series of screen sizes and float-and-sink products to get data for determining the washability characteristics of the coal. Before the screening and float-and-sink tests were made, however, machine cuttings, which are now gobbed underground, were added to the 2-inch to 0 sample. Enough of these cuttings were added so that the resulting mixture was considered representative of what the 2-inch to 0 run-of-mine coal would be if all machine cuttings, including the part now being gobbed, were brought to the tipple as a part of the run-of-mine coal.The mixture obtained referred to in this report as the run-of-mine or raw coal."

Mar 1, 1953

By W. L. Dare

The Federal Bureau of Mines is publishing a series of studies on the methods and costs of mining uranium on the Colorado Plateau. This report describes the longwall-mining methods and techniques used at the Radon mine, Big Indian district, San Juan County, Utah. The tabular Radon ore body lies on the southwest flank of the Lisbon Valley anticline, strikes N. 10° W., dips 7° SW., and has an average thickness of 4-1/2 to 5 ft. The mine is developed by a three-compartment vertical shaft, a haulage level driven beneath the ore, and a system of drifts driven within and parallel to the strike of the ore.

Jan 1, 1961

By James P. McGee

Preliminary calculations show an economic advantage in using nuclear energy to supply the endothermic heat required for gasifying coal. It should be noted that the various assumptions used in preparing these calculations must undergo further evaluation through additional engineering design and research. The proposed system for gasification is the indirect process cycle with helium heated in a nuclear reactor and passed through an exchanger-type gasifier for the reaction of coal and steam to form CO (carbon monoxide) and H2 (hydrogen gas).

Jan 1, 1960

By E. G. Noble

The effects of HBr concentration and temperature on the solubility and hydration state of AlBr3,' CoBr2, PbBr2, MnBr2, KBr, and NaBr were investigated by the Bureau of Mines. Saturated aqueous solutions of the AI, Pb, K, and Na bromides were sparged with HBr gas at 20°, 40°, and 60° C, and saturated solutions of Co and Mn bromides were sparged at 20° C. Increased HBr concentration caused decreased salt solubility because of the common ion effect for all the investigated bromides except PbBr2. Aqueous solubilities at 20° C were, in percent, 51.7 for AlBr3, 53.2 for CoBr2, 1.1 for PbBr2, 59.6 for MnBr2' 39.5 for KBr, and 47.4 for NaBr. At 60° C, the solubilities were, in percent, 53.3 for AlBr3, 2.2 for PbBr2' 46.0 for KBr, and 53.8 for NaBr. Solubilities in solutions sparged to HBr saturation at 20° C were, in percent, 0.5 for AlBr3, 42.0 for CoBr2, 32.2 for PbBr2, 21.0 for MnBr2, 0.6 for KBr, and 0.3 for NaBr. At 60° C, the solubilities at HBr saturation were, in percent, 1.8 for AlBr3, 41.4 for PbBr2, 1.3 for KBr, and 0.4 for NaBr. CoBr2 precipitated out to a minimum solubility of 27.2 pct at 28.7-pct-HBr concentration. Further increases in HBr concentration increased CoBr2 solubility because of the formation of bromide complexes. PbBr2 in-creased in solubility as HBr concentration increased.

Jan 1, 1988

By M. Viswanathan, M. J. Jorgensen, N. K. Kittusamy

Operating heavy construction equipment is often associated with elevated rates of low back discomfort (LBD). However, there have been few formal studies that dealt with evaluating controls that can reduce the LBD among these workers. The objective of this study was to determine the effectiveness of using a continuous passive lumbar motion system (CPLMS) in reducing low back discomfort among operators of heavy earthmoving equipment. The CPLMS is an additional seat support that has a lumbar support bladder and a pump to provide cyclic inflation and deflation. Two groups of operators were identified as potential subjects for this intervention study, the intervention group with a mean age of 41.2 years and experience of 9.7 years used the CPLMS, and the control group with a mean age of 37.5 years and experience of 7.6 years did not use the CPLMS. Body part discomfort surveys were collected from both groups. In addition, the intervention group completed a CPLMS preference survey. The body part discomfort survey was collected up to eight days at three different times of the day. Results from the body part discomfort survey showed a decreasing trend the longer the CPLMS was used, for both the upper and low back region. A decreasing trend for the low back was also found comparing morning to evening discomfort scores across the days when using the CPLMS. When compared to their regular seat, 54% of the operators felt very comfortable in using the CPLMS, 36% of them wanted one for their equipment, and 54% showed interest in experimenting with the CPLMS for a longer time period. Results from this study indicate that the use of a CPLMS can effectively reduce the low back discomfort experienced by operators of heavy construction equipment.

By A. B. Hooler

"A complete list of permissible mine equipment, tested and approved by the Bureau of Mines previous to January 1, 1947, was published as Information Circular 7432. 3/The present list is a supplement thereto that includes all of the equipment approved during the calendar year 1947.The items are numbered to indicate the consecutive order in which each type of machine or device was approved in its particular classification. Thus, Information Circular 7432 showed six air compressors on the active list; two additional compressors, Nos. 7 and 8 in this category, were approved during 1947.Items 2 and 7, unmounted loader and power unit, respectively, under Loading and Conveying Equipment, item 2, rubber-mounted mining machine and item 8, distribution box, appear in Information Circular 7432. They are repeated to show that approvals of these four equipments were extended to cover an additional voltage rating which requires material change in design.Equipment listed in these circulars is approved by the Bureau of Mines only when found upon inspection and test to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal-mining industry. The use of such equipment in mines known to be gassy, as well as in those that may become so, is earnestly recommended in the interests of safety. This circular is published so that the industry may be kept informed as to the many types of machines, devices, and lamps that are available for reducing explosion and other hazards incidental to coal mining. The present paper, with Information Circular 7432, gives the complete list of permissible mine equipment that is available under the various classifications."

May 1, 1948

By Maria I. De Rosa

Table 28 and figure 10 show the number of fires and fire injuries for coal preparation plants by state during 1990-1999. Table 28 also shows the risk rates, employees' working hours, and lost workdays by state. For coal preparation plants, 91 fires occurred in 1 1 states during 1990- 1999. Twenty-three of those fires caused 25 injuries (the yearly average was 9.1 fires and 2.5 injuries). Ten fires and eight injuries involved contractors. The Ewhr value was 24 1 x 10' hr (Irr = 0.02 l), and the LWD value was 198. Pennsylvania had the most fires (24 fires and 4 injuries), whereas West Virginia (22 fires and 7 injuries) and Kentucky (22 fires and 7 injuries) had the most fire injuries. Among these states, Kentucky had the highest injury risk rate value (Irr = 0.025). Table 29, partly illustrated in figure 11, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires decreased during most of the periods (an increase is seen only during the last period). The number of fire injuries show a decrease followed by an increase during the periods, accompanied by a decline in employees' working hours throughout the periods. The Irr values follow patterns similar to those shown by the injury values (see table 29 and figure 11). Tables 30-35 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 12 shows the major variables during 1990-1999. Table 36 shows the fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By J. D. Davis

Coke Since the beginning of manufacturing of metallurgical coke in the United States, which dates from about 1859, Pennsylvania has main tamed supremacy in coke production Available statistics for the year 1880 show an output of 3,338,300 short tons, which was neatly trebled by the end of the succeeding 10 years. From this time on the increase was steady, though not rapid, and in 1922 the total production was 13,991,892 tons, which is approximately 37 per cent of the total coke production of the United States. The main reason for the rapid development of the coke industry in Pennsylvania lies in the abundance of coals particularly adapted to beehive coking, for which purpose the Pittsburgh bed in the Connellsville district has long been looked upon as standard At first practically all metallurgical coke was made in beehive ovens, the only exception being the short lived and wasteful method of coking in piles, byproduct owns did not make then appearance until after 1893 The suitability of a beehive coking coal cannot be accurately predicted from its chemical analysis, but it can be said, perhaps, that the volatile matter should be about 32 per cent, and that the oxygen content should not be mole than 10 pet cent or less than 4 per cent The sulphur and phosphorus content should be small-not over 1 25 per cent sulphur and under 0 02 pen cent phosphorus-and the ash content should not be over 7 per cent The Pittsburgh bed at Connellsvnlle fills these requirements well, as may be seen from the following representative analysis. Analysts of coal from Pittsburgh bed Moisture 1 70 Volatile matter 31 10 Fixed carbon 59 80 Ash 7 40 Sulphur 0 85 B t u 13,990

Jan 1, 1928

Only limited work has been reported in the literature about the use of latex in soil. Unisol 91 2,3 (a 9:l oil-latex emulsion made b International Synthetic Rubber Company) and Phil1ips Petroset4 geotechnic emulsions are surface soil stabilizers which penetrate a maximum of two inches, but do not reduce permeability. Diamond Alkali 5 found that styrene-butadiene rubber latex as a one percent latex-soil mixture reduced permeability to 0.7 from 21 feet per year under a head of twenty feet of brine. We have found no literature reference for use of latex as sealant at depth in the soil, although asphalt has been applied at depth using civil engineering methods6,7. Most of the materials investigated as soil sealants in the present work were latexes, although some studies were also conducted with a variety of inorganic and organic chemicals. Of the latexes tested, most were rubber but a few were plastic, e.g. polyvinyl chloride. Sealants examined in this investigation are listed individually in Table I with supplier, code number, and other pertinent information. The materials consisted of the following general classes with additional details as indicated: 1.Anionic latexes: a. styrene-butadiene copolymers and terpolymers (SBR) b. butadiene-acrylonitrile copolymer (Paracrils®) c. polyvinyl chloride homopolymers and copolymers (WC) d. ethylene-propylene terpolymer e. vinyl acetate homopolymers and copolymers (VA) f. acrylics (acrylate copolymers) g. 2-chlorobutadiene homopolymer (chloroprene) (prepared specially as cationic material coagulated by soil). 2. Water Soluble polymers: a. polyvinyl ether b. methylcellulose c. polyethyleneimines d. polyacrylic acid homopolymer e. copolymers and terpolymers with acrylic acid types (water soluble as sodium or ammonium salts) f. alginates g. monomers (for polymerization in soil, e.g. acrylamide)

Jan 1, 1972

By D. S. Colby, E. M. SEELEY

The total production capacity of the natural-gasoline industry increased to 27,212,000 gallons (647,905 barrels) daily on January 1, 1950, from 21,322,000 gallons (507,670 barrels) daily on January 1, 1948. The rate of growth during these 2 years averaged 13 percent per year, compared with 9 percent per year from 1946 to 1948 and 6 percent from 1944 to 1946. The total number of operable plants on January 1, 1950, was 554, 5 more than at the beginning of 1948. The number of absorption plants increased by 12, the number of cycling plants by 7, and the number of combination plants by 4. The number of compression plants and charcoal plants continued to decrease. Absorption plants accounted for 67 percent of the total capacity on January 1, 1950, compared with 62 percent 2 years previous. Eighty-two per- cent of the expansion in these 2 years was in absorption-plant capacity. Cycle plants accounted for 24 percent of the total industry capacity at the beginning of 1950, compared with 27 percent on January 1, 1948. The average daily capacity of absorption plants increased from 38,400 gallons at the beginning of 1948 to 50,600 gallons at the beginning of 1950. During the same period, the average daily capacity of cycle plants decreased from 150,200 gallons to 144,100 gallons. Texas showed the largest gain in number of plants 13 absorption, 4 compression, and 4 cycling plants. The State accounted for 67 percent of the gain in capacity and on January 1, 1950 had 50 percent total national capacity. Louisiana followed with 7 additional plants. Pennsylvania reported 14 and West Virginia reported 13 fewer plants than in 1948. Most of these reductions were in the number of compression plants.

Jul 1, 1950

By Thomas C. Ruhe

The Pittsburgh Research Laboratory of NIOSH conducted research to determine the safe operating conditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) conserves energy, reduces oil imports, and reduces mining costs. Since RO has a variable composition, there was concern that the additives/impurities it contains may cause ANFO made with RO to be unstable (as compared to regular ANFO) at high summer ambient storage temperatures. Reactivity of RO with zinc was also a concern. Thermal stability tests were conducted to help quantify and resolve these issues. ANFO mixtures (0.66 lb/300 g) were put into sample containers made of steel, stainless steel, and galvanized (zinc coated) steel pipe fittings, which were heated in isothermal ovens. The experimental parameters were temperature settings of 140° F (60° C) and 176° F (80° C), four sample container (pipe fitting) metal combinations, and nominal heating periods of one and three days. The ANFO samples contained 6% each of the following twelve different oils/oil mixtures: No. 1 was diesel fuel, Nos. 2 thru 6 were five candidate oils (2 thru 5 were used oils and 6 was a new synthetic oil), No. 7 was 5% diesel fuel + 1 % graphite, and Nos. 8 thru 12 were 3% diesel fuel + 3% each of the five candidate oils. All samples showed no reactivity when heated at 140° F (60°C). All samples (except No. 7) reacted at 176° F (80° C) in a steel pipe with galvanized caps as follows: No. I reacted most, Nos. 8-12 reacted moderately, and Nos. 2-6 reacted least. All ANFO samples were tested and found not to be cap sensitive.

By R. E. Head, Virgil Miller

"Under existing conditions in the treatment of oxidized lead ores containing small quantities of molybdenum no provision is made for the recovery of the molybdenum. Considerable quantities of this important element are lost in the slags of the lead smelters and constitute an economic waste. There is little or no probability that slag dumps containing molybdenum in small quantities could be economically treated for the recovery of the element, and steps for the prevention of waste in this respect must be taken prior to smelter treatment.Wulfenite, lead molybdate (PbMo04), and molybdite, molybdic ocher (Mo03), are the molybdenum minerals most abundantly found in deposits of oxidized lead ores. Wulfenite contains 39.3 per cent molybdenum trioxide and 60.7 per cent lead oxide; molybdite contains 66.7 per cent molybdenum and 33.3 per cent oxygen. Plumbojarosite, argentojarosite, cerussite, and occasionally anglesite are commonly associated with wulfenite ores, and the oxidized iron content is usually fairly high.The recent discovery and development of a body of wulfenite ore in the Star district near Milford led to a cursory microscopic examination of samples of the ore, followed by a few preliminary tests which had for their object the separation and recovery of the lead and molybdenum in separate products.The microscopic examination showed that the samples used in the work were composed of wulfenite, plumbojarosite, and a small quantity of cerussite, and indicated that the iron content was quite high. The ore was porous and yellowish-brown; crystals of wulfenite appeared to be quite uniformly distributed through it, and this mineral and plumbojarosite (Pb0.3Fe203.4S03.6H20) apparently accounted for the major part of the lead content, although lead"

Sep 1, 1928