Search Documents

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration. Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By D. L. Neylan

The Bureau of Mines evaluated various methods for identifying sources of mercury vapor in excess of the threshold limit value (TLV) of 0.05 mg of mercury per cubic meter of air set by the American Council of Government and Industrial Hygienists (ACGIH) for mines and mineral processing plants. Chemical spot tests and portable devices for mercury determination were evaluated, based on information from published sources and performance in laboratory tests. Among the parameters examined were sensitivity, interferences, cost, ease of use, and other factors pertinent to field application, More than 50 methods were evaluated. The investigators found that many readily available methods are suitable for identifying sources of mercury vapor in mines and mineral processing plants. The best method appears to be one that uses a commercially available mercury test paper sensitive only to mercuric ions. For some of the more promising chemical spot tests, this report includes step-by-step instructions for field application.

Jan 1, 1983

By Bruce K. Cantrell, Stephen W. Stein, David Hassel, Harvey Patashnick

The Mine Safety and Health Administration. Department of Labor, requires coal mine operators to measure compliance with federal re¬spirable dust exposure standards periodically using approved gravi¬metric samplers. However, the gravimetric approach, with its inher¬ent delays, cannot provide dust concentration data quickly enough to allow on-site correction of inadequate dust control strategies or re¬moval of personnel from harmful environments. Furthermore, alleged tampering with dust samples collected to determine compliance with standards prompted the Secretary of Labor to appoint a special Respirable Dust Task Group to study options to improve monitoring and control of respirable coal mine dust. The Mine Safety and Health Administration's Task Group recommended that the U.S. Bureau of Mines develop a fixed-site monitor that would provide continuous information to the mine worker and mine operator regarding dust levels and the status of compliance with the applicable respirable dust standard. In response to the Mine Safety and Health Administration's request, the U.S. Bureau of Mines is investigating several sensor tech¬nologies for continuously monitoring respirable coal mine dust. One of these technologies is the Rupprecht and Patashnick Co. tapered element, oscillating microbalance. The bureau is in the process of investigating the suitability of using this sensor in the high humidity and vibration environment of underground coal mines. Laboratory tests have indicated that, with modification, the sensor can meet the humidity and vibration requirements for underground coal mine use. Currently, the bureau is developing

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration .Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By Jr. Fish

As a part of a study of iron are resources in the Appalachians, 9 diamond drill holes aggregating 1,580.7 feet were drilled in a portion of the Butt Mountain area of northeastern Giles County, Virginia. Three hematitic sand-stone beds were intersected in the Clinton formation but only one was consistent in thickness and grade in all 9 drill holes. This bed averages 18.9 percent iron over an average thickness of 24 feet. The drill cores were logged and chemical analyses were made on 161 individual samples and 22 composite samples. Beneficiation studies were made of three composite hematitic sandstone samples each representing a separate bed containing 14.6, 19.8 and 20.0 per-cent iron. Major mineral constituents of the samples were hematite, quartz, and sericite.

Jan 1, 1967

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the third. The data are accompanied by maps showing the location of holes drilled and deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township-map. The description of each half township is followed by a description of each deposit developed in that half township.

Jan 1, 1948

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the fifteenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by halt townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 halt-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The Descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each halt township is given with the discussion covering that area.

Jan 1, 1948

By Michael J. Friedel

The permeability and flow capacity in unsaturated media are investigated by the U.S. Bureau of Mines for application to in situ copper leach mining. Moisture retention properties are derived and combined with scanning electron microprobe data to characterize the mineralogy, texture, pore size, distribution, and permeability of the host rock. Finite-element modeling is used to derive a saturated permeability, ambient degree of saturation, and assess various injection-recovery schemes. Recommended design modifications for optimization of solution distribution and maximum recovery from the rock matrix requires either (1) the injection pressures on the order of 1,500 psi and recovery wells operating in a suction mode, or (2) performing permeability enhancement, through in situ rubbling. Injection pressures can be reduced to 500 psi with improved recovery and containment of solutions.

Jan 1, 2010

By Thomas M. Nasiatka

Tests with a high-pressure water jet were conducted in the steeply pitching Roslyn No. 5 bituminous coalbed in the Roslyn No. 9 mine, Roslyn, Wash., to determine the feasibility of extracting coal from pillars and from a solid coal face in development without drilling and blasting. During pillar mining, using a hand-held monitor, the best results were obtained with a 0.150-inch- diameter nozzle, a water pressure of 3,500 psi, and a flow rate of 38.5 gpm.3 The rate of mining and productivity were 0.74 ton per minute and 16.6 tons per man-shift, respectively. During development mining, using a monitor mounted on a roof jack, the best results were obtained with a 0.148-inch-diameter nozzle, a water pressure of 4,500 psi, and a flow rate of 40.0 gpm. In one section of the mine where the coal was relatively hard, the rate .of mining and productivity were 0.10 ton per minute and 5.7 tons per man-shift, respectively in another section of the mine where the coal was relatively soft, the rate of mining and productivity were 0.51 ton per minute and 8.3 tons per man-shift, respectively. The tests showed that hydraulic mining methods were more productive than conventional mining methods in pillar mining. In development the productivity of hydraulic mining depended primarily upon the coal hardness. Compared with conventional methods, hydraulic mining methods were less productive where the coal was relatively hard and equally as productive where the coal was relatively soft.

Jan 1, 1963

By Seth T. Reese

THE INJURY DATA and experience at coal mines in the United States for 1949 are presented in this bulletin under the following general sections: (A) General injury experience: 1. Tables 1 to 18: Contain current data on number of injuries, frequency and severity rates, average severity, major and detailed classification of injuries, and distribution of injuries by part of body and days of disability. (B) Selected injury data: 1. Tables 19 to 45: Contain current data on various selected factors of operating and physical conditions that have contributed to the occurrence of injuries at bituminous-coal mines and at Pennsylvania anthracite mines. These factors include extent of hand and machine loading, size of mine by employment and production groups, thickness of bed or vein, duration and number of work shifts, rating of mine as gassy, or nongassy, types of cap lamps, ventilation, explosives, and combinations of factors that influence mine safety. (C) Injury experience by States: 1. Tables 46 to 52: Contain current data on number of injuries, frequency and severity rates, average severity, major classification of injuries, injury records of all coal-producing States, and the relative standing by States according to injury-frequency rates. (D) Appendix: 1. Tables 53 to 84: Contain certain injury data for the years 1943-47 that have not heretofore been published.

Jan 1, 1953

By Philip W. Holland

This U.S. Bureau of Mines (USBM) report describes a chromatographic method that is used for rapid field determinations of carbon dioxide in natural gas streams at a USBM helium production facility. The method employs a commercially available portable gas chromatograph that is equipped with a 10-m fused-silica capillary column coated with a porous polymer. The instrument operating parameters permit determinations to be performed over a concentration range of 10 ppm to 10 pct with a frequency of 20 samples/h. The speed at which determinations can be performed is an important factor when evaluating efficiency or troubleshooting processes at the helium facility.

Jan 1, 1994

By R. W. Hiteshue, C. O. Hawk, H. H. Ginsberg, M. D. Schlesinger

The Bureau of Mines studied single - step catalytic vapor - phase hydrogenation of oils derived from coal and oil shale . Treatment of middle oil , from hydrogenation of bituminous coal , gave good yields of gasoline with a German - made molybdenum- zinc - chromium catalyst . The Bureau also achieved good results with duplicates of this catalyst made from domestic raw materials . In one set of experiments with the German catalyst , 38 to 52 wt pct of feed was converted to gasoline . The total liquid product was 91 to 98 wt pct of the feed . Not all this gasoline can be claimed as production , however , because about 20 pct of the feed was in the gasoline range , and part of it undoubtedly survived the hydrocracking treatment . Hydrogenation of crude shale oil in the presence of cobalt molybdate catalyst produced a total liquid product of 89 wt pct of feed . The hydrogenation converted 27 wt pct of feed to gasoline and 44 wt pct of feed to diesel fuel . The remaining liquid product , 18 wt pct of feed , was residue boiling above diesel fuel . The gasoline was of poor quality , with an octane number of 39.1 . The overall product seemed a suitable feed stock for a conventional refining operation . Coker distillate hydrogenation , using a cobalt molybdate catalyst , gave a total liquid product of 97 vol pct of feed ; of this product 60 vol pct was jet fuel and 40 vol pct was diesel fuel . High nitrogen and sulfur in all three of these raw materials severely poison the usual refining catalysts . Thus , the common objective in these

Jan 1, 1964

By P. W. Jeran, M. C. Irani, D. H. Lawhead

The methane emissions from an advancing coal mine section were continuously monitored for 120 days. During this time, the section advanced 2,000 feet into virgin Pittsburgh coalbed producing 54,565 tons of coal with a total methane emission of 91 million ft3. Analysis of the data gathered showed that daily methane emissions did not correlate with overburden thickness and daily coal production. A good correlation was found between the daily methane emission and the average length of rib exposed to virgin coal.

Jan 1, 1976

By Jozef S. Stachulak

In This Chapter [Ore pass dust control Drill dust control Blasting dust control Conveyor belt dust control Transfer point and crusher dust control Roadheader dust control and How much ventilation air to use] This chapter discusses respirable dust control in underground hard-rock mines. These mines use a wide variety of extraction methods, but they have many common dust sources and dust control needs. Ore passes, drills, blasting, conveyor belts, transfer points, crushers, and load-haul-dump operations can be major sources of dust. Roadheaders, which are sometimes used in hard-rock mines, produce dust in large quantities. For the most part, dust in hard-rock mines is controlled with ventilation air, water sprays, and dust collectors. It is also important to prevent dust from getting into the air in the first place. Good dust control practices will reduce overall mine ventilation requirements. [Lack of maintenance is the main source of dust problems in hard-rock mines according to Rodgers [1974], who conducted a dust survey of hard-rock mines several decades ago. Rodgers found that spray systems had clogged sprays, dust enclosures had improperly fitted skirts, and ductwork was plugged and had leaks. Today’s mines have better maintenance programs (we think), but when dust levels are high, maintenance is still the first topic to address.] The Mining Association of Canada [MAC 1980] and Knight [1980] provide good general information about hard-rock dust control. For conveyor belt dust control, Goldbeck and Marti [1996] and Swinderman et al. [1997] are valuable sources of information.

Jan 6, 2003

By James E. Mills

Coal, in the process of mining, transportation, and handling and on exposure to the weather, is subject to more or less disintegration. This disintegrated coal is usually called "slack" and amounts often to a considerable percentage of the lump coal produced in the mines. If this slack coal is wasted the loss so occasioned ranges from 5 to 50 per cent, or even more, of the total coal mined. It is therefore clear that the utilization of this waste slack coal becomes a serious economic consideration. When the coal is suitable for the production of coke, the utilization of the slack presents no difficulty, as it is in demand for that purpose. If the coal does not produce good coke, but cakes rather readily, the slack can be used for boiler purposes, as it fuses together more or less quickly, and burns on the furnace grate without great loss. Coal that cakes less readily can be burned on grates of special construc- tion. When so used it is more troublesome to handle, and the waste is greater than when lump coal is used. Consequently the price of much of the slack coal for fuel purposes ranges considerably lower than that of the lump coal from the same mine. The full value of this slack coal as fuel can be realized by first form- ing the coal into a coherent mass or briquet, such briquets, when of good quality, being equal to or of greater value than the original

Jan 1, 1911

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Nicaragua has been prepared from the best available information in Washington , but is released subject to correction and amplification , if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State .

Jul 1, 1930

By S. L. Windes

For a number of years, the Bureau of Mines conducted tests on various types of structures to determine the effect of seismic vibrations emanating from quarry blasting in an effort to determine an index of damage . Associated with these tests , occasional records were made of the characteristics of. the air blast or concussion from the explosions . Although the importance of the air - blast problem was recognized , the equipment was not designed for air -blast measurements , nor was the early research program concerned with the problem . After the ground - vibration tests had been completed , attention was turned to study of the air blast and its effect . The air - blast problem in reference to quarry and mine blasting may be divided conveniently into three phases : (1 ) Determination of the fundamental characteristics of the air blast , such as the pressure - time relationship , speed of propagation, attenuation , and the like ; ( 2) effect of blasting conditions on these air -blast characteristics ; and ( 3) determination of the conditions necessary for damage to structures . The initial step was the development of microphones suitable for recording the anticipated blast pressures. Such microphones were designed and built during 1940 , and described in technical detail for publication ( 2)3/. Briefly, the microphone adopted was a small, plate - diaphragm condenser type . The recording was through special transducer amplifiers with low -frequency response to zero cycles per second and a Duddell - type oscillograph of special design .

Feb 1, 1942

By Fred C. Turin, Sean Gallagher, Kim M. Cornelius, William J. Wiehagen

An important part of initiating a site-wide ergonomics evaluation process is prioritizing jobs to be analyzed. While injury data is important, other factors such as worker discomfort and physical exertion requirements, should be considered. This paper describes the use of four sources of data (injury records, the Nordic Standardized Musculoskeletal Questionnaire, supervisor interviews, and management concerns) to prioritize jobs for ergonomic analysis. The approach described integrates the four sources using a decision matrix to prioritize jobs for ergonomics analysis.

By Ronald B. Stotelmeyer

This report summarizes studies of 28 National Forest roadless areas in Montana completed by the U.S. Bureau of Mines (USBM) in the period 1974-1993. It also briefly describes 20 areas for which field studies have not been conducted. All 48 of these roadless areas have been recommended for addition to the National Wilderness Preservation System or proposed as special management areas by the U.S. Forest Service (USFS) or the Montana congressional delegation. The Bureau studies indicate which parts of the roadless areas have a high likelihood for mineral-resource development. They also show where mineral production has occurred in the past and where abandoned mine workings (possible hazards) would be encountered. The number of mine and prospect workings found are a measure not only of surface disturbance, but of areas not wilderness in character. For the purposes of this report, mine refers to a property which produced (or is currently producing) a mineral commodity, a prospect is a property which has been explored but has no record of production.

Jan 1, 1994

By Richard A. Allwes

This U.S. Bureau of Mines report presents the results of structural analyses and full-scale physical tests conducted on a steel-set arch and tri-set. The purpose of the analyses and tests was to evaluate the suitability of these structures for use in roof-fall prone areas. The arch canopy test and design procedures previously developed by the Bureau were utilized in this evaluation. Theoretical resistance functions were established for the steel-set arch and tri-set and were representative of the experimental behavior of the structures. The resistance functions were used to determine the energy absorption capacity of the structures and to predict their dynamic response to impact loading. The dynamic tests demonstrated that the arch canopy design procedure is appropriate for tri-sets and yields conservative designs for both steel-set arches and tri-sets. As a result of this work, it is recommended that these two structures may be considered for use in roof-fall prone areas and for rehabilitation work, provided the arch canopy design procedure is utilized for each application and the principles underlying the design procedure are understood.

Jan 1, 2010