Search Documents

By Chas. F. Jackson

During the past 5 years the Bureau of Mines has published information circulars dealing with mining methods and costs at 78 ore mines; 7 circulars, each of which is devoted to a discussion of one of the principal mining, methods; and 23 circulars dealing with special phases of mining, such as ventilation, shaft sinking, tunnel driving, the cost of equipping and developing prospects and small mines, underground transportation, diamond drilling, and ground support. These circulars were written by many different authors, and in order that the method of presentation and the basis for compilation of data might be the same in all the papers the Bureau drafted an outline to be followed in their preparation. To clarify the data in these circulars, which are in the libraries of many engineers and mining companies, and the summarized data presented in this paper, that portion of the outline dealing with cost and labor-performance data is reproduced below.

Jan 1, 1934

By G. S. Scott

The Bureau of Mines is engaged in research to assess the hazards associated with the handling, storage, and use of combustible gases, vapors, and. liquids encountered in mines and in industry. As a part of this general pro-gram, numerous limits of flammability and ignition temperatures are being investigated for a wide variety of combustible materials, and methods are being developed to minimize the explosion hazards of these combustibles. The Bureau receives numerous requests for information on the explosion hazards of specified combustible mixtures under various conditions of use. This information circular has been prepared to assist those who may have similar requests. Destined primarily for the layman with a limited technical knowledge of the subject, it considers rather briefly the numerous factors that enter into the general problem of gaseous explosions and their prevention.

Jan 1, 1951

By H. K. Sacks

The Bureau of Mines has improved a mine dust incombustibles analyzer originally developed at the Bartlesville Energy Research Center (BERC). This analyzer provides quick, accurate analysis of the percentage of incombustible material present in dust samples taken from mine ribs, roof, and floor so that costly overdusting may be eliminated while still maintaining a proper level of incombustibles. The changes being effected on the present design of the BERC model IV rock dust analyzer should simplify its operation and calibration procedures, resulting in increased accuracy.

Jan 1, 1976

By A. W. Khair, S. J. Jung

"IntroductionIn a typical incremental loading test, the AE activity increases rapidly in the initial stage of the loading. It is associated with initial closure under compression of favorably oriented cracks already present, together with sliding of crack faces against each other /1/. After the initial stage, crack closure and movement largely cease and the AE activity drops to a barely detectable level /2/. In the final stage of loading test, cracking associated with the onset of inelastic deformation' occurs, and the rate of AE rapidly increases /3/ indicating an increase in the •number of events associated with higher number of microcracks. To understand better primary fragmentation process, Anderson and Ruzzi conducted tests to identify a practical method of monitoring fracture development in rock, as caused by an excavation tool /4/. They proved that a relationship existed between the AE activity, generated during fracturing and the amount of fracture surface area created.A process of fragmentation, demonstrated by conical bits acting orthogonal to the flat surface of block of coal specimen with and without lateral confining pressure is presented here. The monitoring of AE during the fracturing process of rock/coal has been a very useful indirect method in studying fracture mechanism.Specimen PreparationLarge blocks of Waynesburg coal were obtained from a surface mine. These blocks were then out and molded to approximate dimensions of 25.4 x 25.4 x 15.2 'an (10 x 10 x 6 in.). These specimens were instrumented with three strain gages in a 45 degree rosette. One was mounted parallel to the bedding plane direction, another was tinted at an angle of 45 degree from the bedding plane direction and the third was mounted perpendicular to the bedding .plane direction. Each of the three strain gages were set 5.1 an (2 in.) away from the impact point.Typical Test ProcedureIn a typical experiment, the specimen was placed in the confining chamber.Predetermined equivalent in-situ stresses were applied to the specimen by using two sets of hydraulic cylinders. Two 1 in. thick steel plates ware positioned between the sample and the hydraulic cylinders in order to distribute the pressure uniformly over the whole surface of the specimen. The LVDT null position was adjusted with respect to the coal face. After setting the LVDT, the bit and associated weight was lifted to a predetermined height (equivalent to a predetermined kinetic energy) by a win. The three strain gages were balanced using the signal conditioner and the output was recorded by a 6 channel strip chart recorder. The experimental set-up is shown in Figure 1."

Jan 1, 1989

By McHenry Mosier

Mercury is one of the strategic metals the supply of which has been raised from critical uncertainty to more than enough for essential demands. Work by the Bureau of Mines has contributes substantially to increased production of mercury in the United States and to consequent accumulation of Governments stock. Other contributing factors were higher prices for mercury and Government loans to operators. The Bureau has undertaken 15 exploration projects, 13 of which have been completed. This work comprised 40,307 feet of drilling arid 35,082 linear feet of sure ace trenching and has indicated commercial ore containing 37,400 flasks of mercury and marginal ore contain¬ing 29,200 flasks - a total of 66,600 flask , equivalent, respectively, to domestic production at 50,000 flasks per year for 9 months , 7 months, and 16 months. Early in 1944, as Government stocks had become adequate, domestic production was gradually curtailed cancellation of Government contracts for the purchase of mercury and Government control of labor and operating supplies.

Jan 1, 1944

By William K. Tolley

The U.S. Bureau of Mines (USBM) is investigating hydrometallurgical processing techniques to recycle metals from semiconductors and other advanced materials. Cadmium and tellurium were recovered from mixed CdTe/CdS scrap produced in the manufacture of thin-film photovoltaic devices. Selective cadmium dissolution was achieved using oxygen-pressure leaching in dilute sulfuric acid. Leaching the scrap for 90 min at 110° C in 2.2NH2S04 under 400 psig 02 yielded 97% Cd extraction; however, cadmium content of the residue ranged between 4% and 7%. Soluble iron was added to the lixiviant to catalyze oxidation of the CdS component. Tellurium and sulfur remained in the leach residue primarily in the elemental form. The iron and tellurium were removed from the cadmium-rich leach liquor by adjusting the pH to 5.3. The cadmium was recovered as cadmium sulfate crystals by evaporating the solution. Alternative leaching and purification schemes are discussed.

Jan 1, 2010

By Wing G. Agnew

[This report presents the results of tests made by the Mining Division, Bureau of Mines, on the relative durability of manganese-steel drill rods and carbon-steel drill rods for use with the detachable bolts]

Jan 1, 1941

By H. E. Harris

An extensive experimental program was carried out to determine the variability of respirable dust samplers and to determine whether area dust sampling is feasible in coal mines. For sampler variability, it was found under laboratory conditions, that a single dust measurement could be as much as 0.30 mg/M3 from the true value at the 95% confidence level. Under actual underground mining operations, this difference could be as much as 0.52 mg/M3 in the 0 -5.0 mg/M3 range. The results from dust sampling on 175 production shifts involving over 2,500 on-man and area dust samples showed that area sampling is viable, but the field investigation did not establish necessarily where the best area locations were.

Jan 1, 1976

By H. M. Thorne

Oil shale, a potential source of products presently obtained from petroleum, is found in many countries. The most extensive known deposits from the standpoint of potential shale oil in place are those in Brazil and the United States of America. Mining methods used for oil shale range from open-pit operations for shallow deposits to room-and-pillar and longwall techniques for deposits with thick overburdens. Oil shales from different sources vary greatly in the amounts and types of organic and inorganic constituents. By retorting, the organic material is converted to oil, gas, and coke. The largest percentages of oil are obtained from materials having the highest hydrogen content. Over 2,000 retorting systems have been patented, but only a few have been used industrially, and no single process seems best for all types of shales or economic conditions. Shale oils have different characteristics, depending on the source rock and method of retorting. They contain large quantities of olefinic hydrocarbons and more oxygen, nitrogen, and sulfur derivatives of hydrocarbons than most petroleums. Consequently, petroleum refining methods usually must be modified for shale oil. This is particularly true in catalytic processing. Hydrogenation, even under mild conditions, improves shale-oil refinability. Several byproducts may be obtained from both the retorting and refining steps,

Jan 1, 1964

By Raymond B. Ladoo

The uses of talc are many but are not, in general well known or fully developed within the last decade several companies have realized the possibilities of greatly increased use and have intelligently proceeded to develop some of the fields which seemed most promising. This has had a tendency to lift talc from the obscurity in which it had existed for years, but the work is only started and much remains to be done. Considerably more attention has been paid to the technology and utilization of talc in Germany and Austria than in this country, despite the fact that the United States produces 65 of the world's talc and Germany and Austria combined but 5.4%. In the "Bericht,uber die tatigkeit des verbends der talcum-interessenten in Oesterreich-Ungarn" (Proceedings of the Austro-Hungarian Talc Association), for the years 1912 and 1913, many notes upon new uses appeared, together with suggestions as to further development of old uses. Aside from a few notes on the use of tar in paper, little has been published in the English language upon this subject. By recent action of the Talc and Soapstone Producers Association (U.S.A.) funds for research into the properties and uses of talc have been made Available and it is hoped that markets will be materially broadened a a result of this work.

May 1, 1920

By Catharine T. Fogg

The U.S. Bureau of Mines investigated the availability of platinum, palladium, and rhodium from 16 deposits in four market economy countries (MEC's). Major recoverable products include 164 Moz of platinum, 80 Moz of palladium, 13 Moz of rhodium, 24 Moz of ruthenium, 4 Moz of Iridium, 2 Moz of Osmium, and 10 Moz of gold. The 12 deposits in the Republic of South Africa are estimated to account for 96.7 pct of total recoverable platinum. The base-case scenario estimates the long-term cost of production including recovery of capital, but provides no return on the investment or O-pct discounted cash-flow rate of return (DCFROR). The total production costs in January 1990 U.S. dollars ranged from $325/oz to $1,288/oz of platinum compared to an average January 1990 price of $492/oz. Approximately 83 pct of total recoverable platinum was economic at a cost level of $4S0/oz or less. At the IS-pct DCFROR, only 26 pct of total recoverable platinum was economic. For platinum-group metals (PGM), attention has been focused on the ratios of the three primary metals: platinum, palladium, and rhodium. Sensitivity analyses were performed to determine the impact long-term rhodium price increases could have on the total cost of production for platinum and palladium.

Jan 1, 1993

By S. H. Ash

California leads the Nation in the number of operating metal mines and the small number of persons employed at individual mines, which reached a minimum irk 1932 with an average of seven men. The mines are scattered over the entire State, which is the second largest in area (155,562 square miles) in the United States. The mines are situated at various altitudes, with portals ranging from approximately 300 feet below sea level to almost 12,000 feet above. Many of the mines can be reached only during the summer, while at others the heat of the regions adds so the difficulties during the summer months Supplied of explosives the use (or, probably more correctly, the misuse) of which constitutes one of California's gravest mining problems; are handled and stored under condition that contribute many hazards. The problem of providing medical care is serious and complicated, especially at small mines and more particularly in the almost inaccessible mountainous regions; instances in which a knowledge of first aid would have been beneficial but was lacking, or when first aid was instrumental in saving life or limb because it was available are too numerous to be mentioned.

Jan 1, 1936

By Carlton E. Brown

Impinger dust-counting methods are used by industrial hygienists for determining the number concentration of unhygienic siliceous dusts in industrial atmospheres. Various statements have been made regarding the size of the smallest particles revealed by the microscopic employed in such determinations. Published data on the subject are quite limited. This report presents information on the size of the smallest particles revealed by light-field and dark-field techniques applied to impinger and electric precipitator samples collected from experimentally established aerosols of silica dust and bituminous-coal dust. Size distribution and number concentration of particles of the various sizes in the aerosols were determined from samples collected by thermal precipitation simultaneously with the impinger and electric precipitator samples. The size of the smallest silica and bituminous-coal dust particles determined in the light-field counting method used was about 1./1, . There was relatively little variation in the values from 8 impinger and 33 A.-C. precipitator samples of silica dust and 13 impinger and 13 A.-C. precipitator samples of coal dust. The coefficients of variation of the values from the four sets of determinations were low, ranging from ± 7.7 to t 10 percent. This size of 1,14 is close to the limit of resolution of the microscopic method used and to various previously suggested values. The size of the particles determined in the dark-field counting method used was smaller than the size (about 0.28A ) of the smallest particles determined in the light-field, oil-immersion method used for the thermal precipitator samples.

Jan 1, 1951

By E. D. Gardner

About 300 tons of gold ore per week was being produced in February 1934 by Thomas D, Herron and Con Laster from the old lake Superior and Arizona workings; the ground was leased from the Magma Copper Co. The workings adjoined but were not a part of the Magma mine. The lessees had been employees of the Magma Copper Co, at the time the Magma closed down for the summer of 1932. Work on the lease began in July 1932 on an exposure of $2-per-ton ore disclosed in a drift; after a few hand-drilled rounds were blasted the gold content increased to about $30 per ton. Extensive sampling by pannings elsewhere of exposed portions of the vein indicated that other ore shoots existed. The last work previously done in the mine was during the World War, when lessees mined a number of small shoots of copper ore. In some of the stapes the copper miners had left a quartzose streak on the hanging wall that carried $15 per ton of gold. This material did not look as if it cried values and evidently never had been sampled. The first shipment of gold ore was made on September 28, 1932. Up to April 1, 1933, 3,778 tons had been shipped and from September 1, 1933, to January 31, 1934, 3,125 tons.

Jan 1, 1934

By Clinton C. Knox

The Townsite mine, consisting of 40 acres in the town of Cardin, Okla., is in the center of a highly productive part of the Picher-Cardin district of the Tri-State zinc and lead field. Previous to the time of the work done by the Bureau of Mines, the property had been partly explored by churn drilling, and an area-of about 8 acres in the southwestern corner had been exploited by underground workings. The Bureau of Mines investigation had as its object the more intensive development of the northern part of the property where previous drilling had indicated a possible ore deposit of commercial grade. Churn drilling by the Bureau began in September 1942 and continued to February 1943. Twenty holes totaling 4,827 feet of bore were completed. Utilizing the information gained from these drill holes, the Weidman Mining Co., lessee of the tract, sank a shaft and proceeded to the exploitation of the indicated ore bodies.

Jan 1, 1949

By Edward L. Burwell

The Bureau of Mines investigated the use of dilute polymer in brine solutions to increase the efficiency of air in gas flooding model oil reservoirs. Slugs (0.23 pore volume) of 500 ppm polyacrylamide were injected into a model, consisting of a high- and a low-permeability core, that had been previously gas flooded to residual oil. Gas flooding was then resumed. Of the total gas volume injected, the percentage entering the high-permeability zone was greatly reduced after polymer injection but remained unchanged when slugs of water without polymer were used.

Jan 1, 1970

On 26 August 1971, the Bureau of Mines, through the Spokane Mining Research Center at Spokane, Washington, approved initiation of the evaluation of oscillatory energy toward enhancing flow of polymer into shale. The effort was an outgrowth of work performed under Bureau of Mines Contract H0210055, "Feasibility Study of Surface Impregnation equipment for the Chemical Stabilization of Coal Mine Structures," wherein feasibility of the impregnation concept was expressed and the detailed design of a machine for impregnation of coal mine roofs with polymer (under static pressure head) accomplished. Under these efforts, the potential enhance¬ment of polymer uptake into the shale thru superposition of oscillatory energy on the static impregnation pressure was suggested. A proposal for investigation of this phenomena entitled "Feasibility Study of the Application of Oscillatory Energy as an Aid to Afford Chemical Stabilization" was presented to the Bureau whereupon a three month program for initiation of investigation was approved.

Jan 1, 1972

By P. G. Guest

"INTRODUCTION Need for More information on Spark IgnitionMany questions have yet to be answered more completely concerning the ignition of flammable gases and vapors by electric sparks. Among these one might mention the following: How do the mixture limits for ignition by sparks and by other means compare? Are the most explosive mixtures of the gases the most easily ignited? How ""hot"" must the spark be or what is the minimum energy required for ignition? Does the electric spark act merely as a source of thermal energy or do aggregations of ions, electrons, and metastable atoms formed during and just before the spark play an important part in promoting chemical reactions that ultimately lead to ignition? It is possible for ignition to occur as a result of a silent or brush discharge? How do the ignition energies with single and rapidly recurring sparks differ? What is the relative effectiveness of long, tenuous sparks in ignition as compared with intense, short-gap sparks of equal energy? What is the influence of the material, size, and shape of the spark electrodes? Does the energy for ignition change noticeably with moderate changes in pressure and temperature of an enclosed gas mixture? What order of lag exists between the occurrence of an incendiary spark and the first evidence of flame propagation? What part of a spark in space and time is most effective in producing ignition? Answers to these questions bear directly on the general problem of flame initiation and propagation and, if sufficiently comprehensive, should contribute much to an understanding of the actual mechanism of combustion."

May 1, 1944

By F. J. Gallagher

"INTRODUCTION The purpose of this circular is to present information on the construction and use of reinforced rubber-jatketed tubing and insulatiag air-line couplings in coal mines Where Airdox is used for breaking coal in order to eliminate: insofar as possible, arcing at the face between Airdox tubing and the track or other face equipment.ACKNOWLEDGMENTThe information given by the W. M. Hales Co., Chicago, Ill and the Peabody Coal Co., Taylorville, Ill., regarding the construction and use of rubber-jacketed tubing and insulating couplings in gratefully acknowledged. GENERAL INFORMATIONSince its introduction into coal mines, the use of Airdox has grown in popularity, especially in the Indiana and Illinois coal fields. Its use permits breaking dawn coal on shift, whereas the use of explosives for blasting coal on shift is prohibited by law in those States. Many of the hazards connected with the use of explosives are eliminated. The accident experience in the use of Airdox has been excellent with respect to the number of fatalities or serious injuries per million tons mined.The Federal Mine Safety Code specifies that Airdox lines should be grounded at the compressor and at other points of low resistance along the lines but should not be connected to tracks, pipe lines, or other possible power conductors. The majority of operators in the Indiana and Illinois coal mines, in which Airdox is used, approve the precautions embodied in the code regulationsIf Airdox lines are grounded in accordance with the Code, the following hazards persist:"

Sep 1, 1949

By M. H. Kline

The Scarlet mine, in Randolph County, N. C., was operated on a small scale at intervals from 1899 to 1915, but no records of the quantity of ore produced are available. J. I. Moore unwatered the mine in March 1948, and Bureau of Mines' engineers examined the underground workings. Several assays checked previous sampling of the mine and indicated a small but comparatively high-grade copper-zinc deposit. The high metal content of the veins and the possibility of developing additional reserves prompted the Bureau of-Mines to drill three holes, totaling 530 feet, at the deposit during March and April 1948. Drilling disclosed that the mineralized vein did not extend over 300 feet along the strike and is probably limited in depth to the contact with the granite mylonite.

Jan 1, 1949