Search Documents

By A. Gene Collins

This report discusses some of the chemistry and geochemistry of cesium and rubidium. Knowledge of the cesium and rubidium content of oilfield waters aids in resolving the origin of waters and petroleum, exploring for petroleum and other valuable minerals, discovering water pollution sources, and augmenting the knowledge of geologic formations. The methods described in this report permit the detection of less than 0.01 mg/l of cesium and/or rubidium in a complex oilfield brine or water. Solvents possessing high-dielectric constants were evaluated for their ability to extract cesium and rubidium tetraphenylboron from oilfield waters and for their flame emission characteristics. Nitroethane was selected and used for the extraction and flame spectrophotometric determinations because it gave the highest sensitivity. Cesium 137 and rubidium 86 were used to determine the extraction efficiencies, which were about 87 percent and 58 percent respectively using a single 10 ml nitroethane extraction from a distilled water matrix. The standard deviation of the determination was 0.0008 mg for cesium and 0.0007 mg for rubidium in the 0.01 mg range.

Jan 1, 1965

By Lloyd Williams

1. Reserves have been estimated for three coal beds in Bledsoe County, Tenn.: Morgan Springs, Lantana, and Sewanee. The Richland and Nelson beds occur in Bledsoe County also, but there was not enough information on them for making an estimate of reserves. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated at 43 million tons as of January 1, 1954. Of this total, 22 million tons represents coal 28 inches and more thick. Areas in the beds were omitted from the estimate because available data relative to the bed characteristics were insufficient for making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves deter-mined by this investigation.

Jan 1, 1956

By A. B. Hooker, L. C. IlsLey

The greatest hazard of early mining was from explosions of methane ignited by open lights . With the advent of safety lamps and forced ventilation this hazard was greatly reduced until the application of electricity to modern mining not only multiplied the sources of gas ignition but the accompanying , machines and haulage systems increased the amount of explosive dust , through which a methane explosion is more liable to become a major mine disaster , and thus greatly furthered the need of adequate ventilation to keep down the concentrations of methane . Adequate ventilation is still the best preventive of such explosions . However , even with a well laid out and controlled ventilating system the amount of air passing through entries and rooms is liable to vary within wide limits because of open doors , falls of rock , or other accidental causes . The percentages of methane under normal conditions should therefore be kept so small that they will not be increased to explosive proportions by short interruptions in ventilation . Mine ventilation and methane detection are inseparable safety precautions . The increasing importance of ventilation necessitates more accurato determinations of the methane concentrations throughout the mines . This paper discusses in detail some of the steps in the development of methane detection and specially notes the more accurate detectors now available . One of the earliest means of detecting methane was by a candle . About 1835 , John Buddle , Sr. , a noted mining man of his period , when questioned by a Parliamentary Committee as to the safety of using candles , replied :

Jun 1, 1933

By R. Dell Davidson

This report contains the results of the work performed by Dayton T. Brown. Inc., Testing Laboratories, Bohemia, New York, under the Department of Interior, Bureau of Mines, Contract J0166089 entitled "Performance Testing of Air-Line Linking Components." The objectives of the program consisted of the following: 1. To conduct engineering tests that will provide data to recommend the performance criteria for air hose and piping connections. 2. To determine the requirements for restraining devices which are used to comply with MESA Health and Safety Standards 55, 56, 57,13-21.

Jan 1, 1978

By Pamela J. Watson

This report presents a Bureau of Mines literature survey that provides a data base useful for current and future studies in the area of chemically enhanced drilling and cutting. Publications describing laboratory testing and field studies of drilling and cutting with chemical additives are reviewed. Significant results are summarized and tabulated by rock or material type and also by chemical additive, with extensive references. Selected studies related to fluid-enhanced processing or material testing are summarized in the appendixes.

Jan 1, 1985

By Donald M. Hausen

Diamond-bit performance and cost data accumulated by the Bureau of Mines in core-drilling schists reveal significant trends of economic interest. Low-quality, small-size drill bort were the most economical. The percentage of core recovery, type and size of bit, and bit matrix are also correlated with bit performance and costs. Detailed analyses of the factors affecting diamond-bit performances and costs are assessed in the tables, graphs, and discussion.

Jan 1, 1956

By J. W. Lyman

The U.S. Bureau of Mines investigated methods of separating valuable rare-earth materials from Fe in neodymium iron boron (NdFeB) magnet scrap. A selective oxidation treatment of the scrap oxidized the rare-earth portion while leaving elemental Fe. Magnetic and leaching procedures were tried for separating the metallic Fe and rare-earth oxides, but the extremely fine grain size of the oxidized scrap prevented recovery by either technique. The best separation of rare earths from bulk NdFeB magnet scrap was obtained by dissolution with H2S04 followed by precipitation of recyclable rare-earth salts. By precipitating neodymium-alkali sulfate double salts as an intermediate that can be converted to a variety of useful products, many materials-handling and economic disadvantages found with direct precipitation with fluoride or oxalate were avoided. Iron was removed from magnet leach solutions by precipitation as a jarosite, eliminating a major disposal problem. Research was also conducted with contaminated mixed SmCo5 and NdFeB swarf. Using a flotation-leaching technique allows the SmCo5 to concentrate in the froth, while the grinding-medium contaminant sinks and is removed as tailing. The NdFeB is dissolved by H2S04 during the process.

Jan 1, 2010

By H. L. Burmeister

These properties were examined by a Bureau of Mines engineer in 1949. During 1950, these mines were studied by the Bureau to determine the possibility of increasing the production and augmenting the supply of fluorspar. As a result of this study, it was decided to core-drill the Knox-Yingling vein to test the continuation of fluorspar to a greater depth than that reached by mine workings. It also was desired to relate the present deposit with the Rosiclare formation. Development work by the Bureau of Mines was performed from February to May inclusive in 1951. Four diamond-drill holes aggregating 2,733 feet were drilled in the hanging wall of the vein.

Jan 1, 1952

By Jon C. Volkwein

The Bureau of Mines conducted a series of tests to evaluate the effectiveness of mixing a compressed-air-generated foam with dried whole-grain silica sand to suppress dust in minerals processing plants. Dust at downstream transfer points was monitored with personal gravimetric samplers and with Real-Time Aerosol Monitors (RAM's) that were connected to strip' chart recorders. Results showed dust reductions of 80 to 90 pct on three separate occasions at two different plants. The mechanism by which foam suppresses dust is discussed, as are the constraints on the use of foam, which may include incompatibility of the foam with the mineral product, difficulty in controlling the foam generator, and cost.

Jan 1, 1983

By T. H. Jeffers

To help maintain an adequate supply of minerals to meet national, economic, and strategic needs, the Bureau of Mines investigated the feasibility of extracting copper from coarse native copper ore with ammoniacal ammonium carbonate solution by a simulated in situ leaching procedure. A 5.9-metric-ton (6.5-ton) sample of minus 30.5-centimeter (12-inch) conglomerate-type ore analyzing 1.96 percent copper was leached in a column for 556 days with a solu-tion that contained, in grams per liter, 2.2 NBs and 1.9 CO[3=]. The copper extraction was 71.4 percent, and reagent consumptions were, in kilograms per metric ton of ore, 1.1 NBs and 0.85 CO[3=] (in pounds per ton of ore, 2.2 NH3 and 1.7 CO[3=]). The pregnant leach solutions contained about 1.4 grams per liter copper, which was readily extracted from these low-tenor liquors with a 1:19 mixture of an organic extractant and kerosine. Copper was stripped from the loaded organic with depleted electrolyte containing 150 grams per liter H2S04, and the copper was recovered by electrowinning with antimonial lead anodes. Conditions also were established for minimal lead transfer to the cathode copper.

Jan 1, 1979

By D. S. Kingery

Investigations over several years have disclosed that the principal manners of occurrence of shuttle-car injuries are in order: 1. Victims in contact with roof or crossbars. 2. Victims in contact with ribs or timber legs. 3. Victims falling from, or jerked from, shuttle cars. 4. Victims in contact with overhanging brows or protruding pine for pin timbers, or water lines. 5. Contact with persons or collisions with parked equipment. 6. Victims injured by roof falls or falling timbers caused by knocking out roof supports with shuttle cars. 7. Victims injured by runaway shuttle cars. 8. Victims injured while loading or unloading timbers or other materials from shuttle cars. These recurring types of shuttle-car accidents reflect the physical conditions of the working sections, certain safety deficiencies in shuttle-car maintenance and design, and unsafe practices by operators.

Jan 1, 1952

By William H. Waggaman

The United States not only is the largest producer of phosphate rock but also manufactures and consumes greater quantities of phosphate products than any other country. New and expanding uses will increase even further the demand for this basic raw material. Only a small proportion of the total quantity of phosphate rock mined and marketed is consumed directly in a raw or unprocessed state; the vast bulk is chemically treated and converted into [ertilizer] and a wide variety of finished products that play a vital role in [r] national economy. Three fundamental methods are employed in decomposing phosphate rock. 1. Reduction by carbon at high temperatures. 2. Treatment with one or more acids. 3. Calcination or fusion with silica, sodium salts, magnesium minerals, or small quantities of phosphoric acid.

Jan 1, 1960

By Bernadette C. Michalski

THE RAPID GROWTH of the small Albanian mineral industry in the 1950's began to taper off by 1961 and slackened sharply in 1963. The abandonment of Soviet and East European technical assistance programs in mid-1961 greatly affected Albania's mineral development, since four-fifths of all technical aid personnel were engaged in mineral activities. Chinese assistance apparently has not been able to fill the void. Overall mineral production increases during 1961-63 averaged 1 percent per year in value, as compared with 3 percent in 1959 and 5 percent in 1960. Although by world standards Albanian mineral output, except for chromite, is insignificant, it is vital to the country's domestic economy. The mineral industry generated about 14 percent of the gross industrial product in 1962 and employed a notable share of the industrial labor force. In recent years, mineral products have provided about three-fifths of the country's exports by value. Chromite and iron-nickel ores together constituted from one-fourth to one-third of the total export value. In 1963, total trade turnover increased 12 percent over 1962.

Jan 1, 1964

By G. W. Birge

This report describes the carbonizing properties of the principal coal beds of McDowell County, W. Va. Coals from 14 coal beds were selected for study: Upper Cedar Grove, Middle Cedar Grove, Lower Cedar Grove, Eagle, Douglas, Iaeger, Sewell, Welch, Beckley, Fire Creek and Pocahontas Nos. 3, 4, 5, and 9. Selection was based upon estimated minable reserves. McDowell County coals rank either as high-volatile A, medium-volatile, or low-volatile bituminous coal, and this variation in rank is reflected in the wide diversity of the carbonization properties of the coals. All coals tested were either satisfactory as mined or could be upgraded to meet present chemical standards for metallurgical coke; the coals produced strong coke, as determined by ASTM shatter and tumbler tests.

Jan 1, 1958

By H. Tomlinson

The development of the Sevier Valley Coal Co.'s mine marks the opening of the Salina Canon coal district in Utah. The mine is favorably located with respect, to the existing markets of the West, and if the present estimates of the amount of workable coal in it are accurate it has many Important advantages in favor of its development. This mine is situated 18 miles east of the town of Salina, Sevier County, Utah, which at present is the nearest shipping point oh the Marysvale branch of the Denver & Rio Grande Western Railroad, and is about 152 miles south of Salt Lake City, which is the distributing center for much of the coal from the Carbon - Emery coal field and is the place from which nearly all Utah coal shipped to San Francisco and points on the northern Pacific coast has a common haul.

Jan 1, 1930

By Potter G. M.

Ore-dressing tests were conducted on a sample of ore submitted by the Richmond Hill Mining Co. of Lead, S. Dak. as a part of the Bureau of Mines program for investigating potential domestic sources of manganese. Half of the sample was taken from the 300-foot level and half from surface cuts. The problems involved were liberation and rejection of silica and iron and removal of lead, Silver, and gold from the manganese concentrates. Although a portion of the silica and iron oxides was too intimately associated with manganese minerals for rejection by ore-dressing methods, thus limiting recovery of high-grade concentrates, the Richmond Hill ore was found amenable to simple gravity methods of concentration for producing intermediate-grade products. By jigging and tabling, 73.8 percent of the total manganese was recovered in a product that, when sintered, assayed plus 40 percent Mn. Lead, silver, and gold were successfully removed from gravity concentrates by a chloridizing roasting treatment.

Jan 1, 1948

By Frank J. Wiebelt

The Carbonate King zinc mine is on the west slope of Kokoweef Peak, Ivanpah Mountains, San Bernardino County, Calif. It has produced more-than 10,000 tons of ore with a 39-percent?zinc content since mining operations began in 1940. The ore, consisting principally of calamine and smithsonite, occurs in replacements of the YellowPine limestone. Milling, has been done from the surface to a depth of 275 feet. Eight holes, aggregating 2,121, feet were drilled by the Bureau of Mines in an endeavor to establish extensions of the worked-out ore bodies and to develop new ones. Although indication of mineralization was found in several of the holes, no new ore bodies were developed.

Jan 1, 1949

By James Westfield

A brief resume follows of some recent activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous-Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consultation with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors during their inspections of bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior October 8, 1953, following further consultations with representatives of management and mine workers, and was incorporated by reference in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. The inspectors were active in making prompt investigations of hazardous mines that had been closed by order of the Coal Mines Administrator to determine if enough improvements had been made to allow the mines to reopen. Federal coal-mine inspectors also had temporary authority to close mines they found to be imminently dangerous, but such authority (under Executive Order 9728) was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1957

Coal research and technologic work by the Bureau of Mines covers a broad program of investigation aimed at conservation and utilization of this important natural resource. Conservation is served by a constant search for higher efficiencies in mining, preparation, and use. Increased utilization is sought through various projects that probe new ways to use coal and expand existing coal markets. This report, the twenty-eighth in the series,3 gives the highlights of Bureau of Mines coal research and technologic work in 1963. The scope and complexity of the program makes it virtually impossible to report all progress on every project, even tor a 12-month period. Full insight into each project can be gained only through intensive review of basic objectives, past accomplishments, and current status of the work. Details of the work are given in numerous publications issued by the Bureau and its laboratories and centers located throughout the country.

Jan 1, 1964

Coal research and technologic work by the Bureau of Mines covers a broad program of investigation aimed at conservation and utilization of this important natural resource. Conservation is served by a constant search for higher efficiencies in mining, preparation, and use. Increased utilization is sought through various projects that probe new ways to use coal and expand existing coal markets. This report, the twenty-eighth in the series,3 gives the highlights of Bureau of Mines coal research and technologic work in 1963. The scope and complexity of the program makes it virtually impossible to report all progress on every project, even tor a 12-month period. Full insight into each project can be gained only through intensive review of basic objectives, past accomplishments, and current status of the work. Details of the work are given in numerous publications issued by the Bureau and its laboratories and centers located throughout the country.

Jan 1, 1964