Search Documents

By W. E. Robinson

A laboratory study wan made to determine whether drying and preheating Colorado oil shale with waste retort gases has any appreciable effect on its oil yield. Samples of crushed oil shale were heated at subretorting temperatures in a specially constructed electric furnace by gases similar in composition to waste gases from oil-shale retorts. The results of this study showed that preheating oil shale with nitrogen or a reducing mixture had no effect upon the oil or water yield. However, oxygen in the preheating gas caused a decrease of oil and an increase of water. In general, the oil yield decreased with (1) increase in oxygen content of the heating gases, (2) increase in temperature of the heating gas, (3) increase in heating time, and (4) decrease in the particle size of tho shale. The decrease in oil and the increase in water resulting from preheating were due to oxidation of the benzene-insoluble organic material (kerogen) rather than to oxidation of the benzene-soluble organic material (natural bitumen) in the shale, A small amount of oil was volatilized during preheating, which would constitute an additional loss if prober precautions were not taken to recover it. The results obtained in this laboratory study indicate that oil shale can be preheated without appreciable decrease in oil yield by proper selection of preheating conditions.

Jan 1, 1951

By L. B. Berger

Studies showing the effect of mixing hot exhaust gases with tie intake air of a four-stroke-cycle Diesel engine are described. The results indicate a marked increase in carbon monoxide in tip exhaust gases, a decrease in oxides of nitrogen, and no significant effect on aldehydes. The increase in carbon monoxide was greater at higher fuel-air ratios and was caused partly by the increase in fuel-air ratio end partly by the decrease in oxygen concentration resulting when exhaust has was added. The application of these results to the use of Diesel engines underground is considered.

Jan 1, 1940

By Lewis C. Karrick, Martin J. Gavin

"Introduction.The theory of fractional ""education"" of oil from oil shale has been used by several inventors as the basis for the design of retorts for the production of oil from the oil shales of the United States. The term fractional ""education"" gives expression to the rather common belief that when an oil shales is heated it produces light, low-boiling oils as low temperatures, and increasingly heavier, higher-boiling oils as the temperature of retort¬ing rises. The theory evidently had its origin in the fact that crude petroleum may be fractionally distilled, yielding light oils at low distillation temperatures, and heavier oils as the distillation temperature increases is as, gasoline is produced from petroleum at relatively low temperatures, kerosene at higher temperature, and heavier products such as gas-oil and lubricating distillation at still higher temperatures.The writers have examined several oil-shale retorts designed to take advantage of the belief that crude, and in some cases refined, gasoline can be recovered from the shale at low temperatures; kerosene at higher temperat.res, and so on. Such retorts are usually designed to operate continuously and have several vapor-pipes lending from them at differing intervals and passing to separate condensers. Designers of such retorts repeat that the distillate from the low-temperature parts of the retort will be gasoline, and that as the shale passes to zones of increasingly higher temperatures, the vapor lines lending from these zones rill remove increasingly heavier products such as kerosene, gas-oil etc."

Mar 1, 1924

By J. A. Herdlick

Under authority of the Strategic Materials Act of June 1939, the Federal Bureau of Mines, in cooperation with the Geological Survey, began a broad program of investigation of the strategically important chromite deposits in Sweetgrass, Stillwater, and Carbon Counties, Mont. Extensive occurrences of chromite along the Stillwater Complex in Stillwater County were investigated. The two principal deposits, The Mouat-Sampson and Benbow mines, ultimately were developed and placed in production by the Federal Government. As a part of this general development program, the Carbon County chromite deposits near Red Lodge were examined by Bureau of Mines engineers in 1940, and by the Geological Survey .1-1 1942. The district was examined earlier by Schafer, and the Four Chromes area is mentioned briefly by Westgate. Although the Red Ledge deposits were considered to be of minor importance as compared to those of the Stillwater Complex, several of the ore bodies were adaptable to open-pit mining' methods, and one large deposit on Line Creek Plateau was readily accessible to the Red Lodge-Cooke highway. In 1941, the U. 3. Vanadium Corp. began mining crude lump-chrome ore from the deposit on Line Creek Plateau to supplement national stockpiles, which were being depleted by the rearmament program and the disruption of chrome-ore imports by the European war. Access roads gore constricted to Hellroaring Plateau, and the mining operations were extended to that area. A gravity concentrator with a capacity of 200 tons per day was built and operated at Red Lodge to beneficiate lower-grade ore from the district.

Jan 1, 1948

By R. V. Ramani, R. Bhaskar

"An airborne dust cloud is an ensemble of particles of varied size, density, shape and states of aggregation. An understanding and quantifying of the dispersion and deposition of the dust generated in mines is essential to the development of measures for reducing worker exposure to dust. In coal mining, the major portion of the dust is generated during the cutting of coal using a shearer or a continuous miner.The major phenomenon affecting ambient concentration is the deposition of dust. Particle deposition may take place due to the effect of gravitational, inertial, electrostatic, and thermal forces, and mechanisms such as Brownian and eddy diffusion and inertial impaction, The three major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. The mechanisms determining particle deposition are size depend,From a review of the literature, there appears to be a knowledge gap in the understanding of the deposition phenomena in mine airways. In order to obtain a better understanding of the deposition of dust for various particle sizes, and to develop a set of data for evaluating predictive mathematical models for dust-flow in mines, a series of dust flow experiments was performed under controlled conditions in mine airways. It appears that the deposition data generally follow the theoretical behavior of dust based on the combined effect of diffusional and gravitational deposition. In this paper, the findings of the study on the deposition of dust in mine airways and its dependence on size, velocity and concentration are discussed. A set of deposition equations that could be used to determine the approximate deposition at various points in a mine airway are presented.The major factor affecting ambient dust concentration in mine airways is the deposition of dust. Particle deposition may take place due to the effect of gravitational, inertial, electrostatic, and thermal forces, and mechanisms such as Brownian diffusion, eddy diffusion and inertial impaction. The major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. Inertial impaction is significant only during changes in direction, but the change in direction of flow with resultant powerful eddies may cause increased re-entrainment of the particles, thus having a compensating effect. While the literature in aerosol sciences contain several references on deposition, most studies were done in small diameter tubes for diffusional deposition (Liu and Agarwal, 1974). The deposition data from small diameter, short tube experiments may not be applicable to studying deposition in mine airways that have large areas and extend several hundred meters. Further, the change in concentration along the length of a mine airway may significantly affect the deposition, an aspect that may not be easily determined in short tubes in laboratory experiments."

Mar 1, 1992

By A. L. Peyton

The Brewer mine, near Jefferson, Chesterfield County, S. C., was originally operated as a gold mine. As late as 1890 this mine was reported to have been one of the large gold producers in the southeast. Occurrence of topaz on the Brewer property was not reported until 1935, when it was discovered, by Parks3/ and Parks of the Federal Geological Survey while they were investigating gold deposits in the Piedmont province.

Jan 1, 1953

By Gordon R. Sima, John L. Bennett, Roger L. King

Electric shocks are a serious problem in the mining environment. Because of extremely wide ranging use of electrically powered equipment in the mining industry, the hazard to personnel due to electrical shock and related injuries are not restricted to any single area but cover the entire spectrum of mining activity. Electrical accidents, resulting in personal injury, due to im- proper or complete lack of grounding of electrically operated mining machines, form a significant percentage of the overall electrical accident picture. The object of this paper is to describe methods of detection of unsafe electrical conditions with respect to the grounding of electrically operated mining equipment. It also includes a discussion of prototype instruments which effectively monitor the condition of the grounding safety devices currently in use on mining equipment and warn of dangerous conditions as soon as they appear. The paper is based on work accomplished under USBM Contract Number 50357115. The contract was initiated under the Pittsburgh Mining and Safety Research Center Program. It was administered under the technical direction of PM and SRC with Mr. Roger L. King as the Technical Project Officer. Mr. Daniel B. Dawkins was the Contract Administrator for the Bureau of Mines.

By John R. Bradley

The available supply of fuel and power is a subject of importance at all times and particularly at this time. The following brief survey of fuel and power in the United States appraises the extent of the several primary sources of energy the approximate monthly demand, 1929-40; the chief centers of production and consumption; and shifts in the principal uses from 1929 to recent years. The period covers the boom year 1929, the years of the great depression, the more normal year 1937, the recession in 1938, the year 1939, and 1940 (which was affected by armament programs). In some instances, the data for 1939 and 1940 are preliminary. The four primary sources of fuel and power are coal, petroleum, natural gas, and water power. Wood fuel, important in some regions, and foreign trade in natural gas and hydroelectricity represent a relatively small part of the energy supply and are not considered in this study. The tonnages shown are in terms of coal, based upon the calorific or B. t. u. equivalents of the several sources of power. In practice, the usable heat or energy varies according to the type of equipment available for its use. For example, the efficiency of turbine water wheels and internal-combustion engines is much higher than that of steam plants and household-heating devices.

Jan 1, 1941

By George R. Ingham

This paper is one of a buries being prepared by the Bureau of Mines on mining methods and costs at various mines in the United States, and is a description of the mining practice at Ajo, Ariz., where the New Cornelia Branch of the Phelps Dodge Corporation mines copper ore from an open pit, and operates a concentrator for the treatment of the ore thus mined. ACKNOWLEDGMENTS The authors wish to express their appreciation to M. Curley, manager of the New Cornelia Branch of the Phelps Dodge Corporation, for his review of this paper and permission to publish it. They also wish to acknowledge the assistance given by W. C. Lawson, assistant engineer, in the preparation of the paper.

Jan 1, 1932

By Daryl E. Radcliffe

This report describes an instrument system developed by the Bureau of Mines to continuously monitor and record changes in roof displacement during underground mining activity. The instrument consists of a single-wire extensometer coupled to a mechanical-drive chart recorder mounted in an aluminum frame installed in the roof. The unit is small and simple to install and meets safety requirements for use in underground coal mines.

Jan 1, 1977

By Eric R. Bauer

The magnitude and rate of advance of an inmine coal squeeze was deter-mined by measuring roof-to-floor convergence on a regular basis. A dial-gage tube extensometer was used to collect data. Using these measurements) Bureau of Mines employees drew contour maps and graphs to show the direction and rate of squeezing. Information on the rate of squeeze advance was used to determine whether steps should be taken to prevent roof and/or floor movement from closing an entire section of the mine and if alteration of mining plans was necessary to prevent further squeeze development. Data analysis revealed that the squeeze was decelerating; thus there was no need to strengthen support in the areas of the mine that were studied. Mining plans were altered, however, as a result of the findings of this investigation.

Jan 1, 1981

By L. Cheng, M. S. Seehra, P. S. Raghoottama

The four major IR bands of a-quartz at 1080, 797, 693 and 488 cm-1 are studied at room temperature by FTIR-Photoacoustic Spectroscopy. Using Rosencwaig-Gersho theory, equations for the PAS signal q for the thermally thin and thermally thick cases are derived and it is shown how thin to thick transition occurs and leads to saturation as the sample mass is increased. For sample mass < 2 mg, q is proportional to sample mass thus defining the region for quantitative analysis. The dependence of q on the chopping frequency f is found to vary as q f-n with n ? 0.9 for quartz, in good agreement with the RG theory.

Jan 1, 1989

By Donald F. Reed

In the Coastal Plain sedimentaries of northeastern Mississippi, high-alumina clays and kaolins, which are bauxitized locally to varying degrees, are found in many places along the contact between the Midway (Paleocene) and the Wilcox (Eocene) series. The trace of the contact extends from Tippah County, on the Tennessee border, south to Winston County, thence southeast to Lauderdale County, and into Alabama. Its length within Mississippi, disregarding sinuosities, is 185 miles (fig. 1). Commercial production of bauxite from the region has amounted to about 400 tons, shipped from one outcrop in Komper County. In December 1941 and January 1942, the Bureau of Mines and the Federal Geological Survey made a reconnaissance survey of the contact zone and selected the most promising areas for further study. In 1942, four areas in Benton, Union, and Pontotoc Counties were investigated by auger and rotary core drilling, and in 194, core drilling was done on five areas in Kemper, Noxubee, and Winston Counties. The present report records the work done by the. Bureau of Mines and the factual data obtained from the investigations of the nine areas in the two projects.

Jan 1, 1952

By L. B. Berger

Studies showing the effect of mixing hot exhaust gases with the intake air of a four-stroke-cycle Diesel engine are described. The results indicate a marked increase in carbon monoxide in tip exhaust gases, a decrease in oxides of nitrogen, and no significant effect on aldehydes. The increase in carbon monoxide was greater at higher fuel-air ratios and was caused partly by the increase in fuel-air ratio end partly by the decrease in oxygen concentration resulting when exhaust has was added. The application of these results to the use of Diesel engines underground is considered.

Jan 1, 1940

By J. D. Sargent

Selenium might be described as a paradoxical element, being either a metal or a nonmetal, a conductor or nonconductor, amorphous or crystalline, colorant or decolorant, and a hydrogenator or dehydrogenator. Selenium was discovered in 1817 by the Swedish chemist, Berzelius, while studying flue dust from the lead chambers of the sulfuric acid works at Gripsholm, Sweden, The ordinary stable form of selenium is a crystalline, grayish solid with semi-metallic luster. It melts at 217° C., boils at 684.8° C., and has a density of 4.79.

Jan 1, 1955

By Charlie Wyche

In 1980, gold, silver, and pit and quarry construction materials were the principal minerals produced in the Dominion of Fiji. The combined value of these minerals totaled some $7.2 million,2 over 85% of all mineral production, Production of cement, sand and gravel, and quarry products continued to increase, but gold and silver production from Fiji&apos;s only operating mine declined slightly from the previous year&apos;s level. Mineral exploration has been carried out by U.S., Australian, British, Canadian, West German, and South African companies since the early 1960&apos;s, and a high level of activity was maintained throughout 1980. At the end of 1980, some 40 mineral prospecting licenses covering over 4,300 square kilometers were in force, and 19 applications were under consideration by the Mineral Resources Department. Total expenditures by mining companies on land base projects exceeded $6 million in 1980.

Jan 1, 1982

By R. A. Franks, G. F. Friel, J. C. Edwards, L. Yuan

Five mine fire experiments were conducted in a 2.08m high and 2.90m wide, ventilated mine entry in the National Institute for Occupational Safety and Health (NIOSH)&apos;s Safety Research Coal Mine (SRCM) to determine the effect of the dispersion of carbon monoxide (CO) on mine fire detection. CO measurements were made at distances from 7.6 m to 45.2 m downwind from the fire with diffusion mode CO sensors positioned near the roof. For small intensity fires, less than 30 kW heat release rate, generated by 14 kg coal in a 0.61 m square tray, it was determined that air flow and sensor spacing were significant for fire detection at the 10 ppm CO alarm level. Within 15.0 m downwind distance from the fire, 10 ppm CO alarm values occurred for volumetric air flows less than 11.5 m3/s. However, the 10 ppm CO alarm value did not occur 30.0 m downwind from the fire for air quantities greater than 6.2 m3/s due to dilutive mixing of the CO in the air stream. The criterion that the mine fire alarms occur within 15 min of the onset of flaming combustion could not be consistently met with the 10 ppm CO alarm. This suggests the use of lower CO alarm values, or reduced CO sensor spacings for mine fire protection. It is demonstrated how computational fluid dynamics (CFD) can be used to model the CO dispersion downwind from the fire in support of a plan to optimize sensor spacings.

By Spencee L. Willett

In 1986, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied a 51, 160-acre portion of the 107,920-acre Diablo Mountain Wilderness Study Area (OR-001-058) in order to evaluate its mineral resources. The study area is located 1n Lake County, OR, about 45 miles northwest from Lakeview. The study area is located near the northwest corner of the Basin and Range physiographic province. Tertiary Picture Rock basalt with tuff interbeds underlies the area (Travis, 1983). No mineral resources were identified; no mines, prospects, claims, or mineralized areas exist in or adjacent to the Diablo Mountain study area.

Jan 1, 1987

By Martin Hertzberg

The early and reliable detection of the self-heating of combustible substances in mines is of considerable importance to the mining community. This Bureau of Mines report describes the results of a variety of studies of incipient combustion and its detection. Heated samples of coal, wood, and various polymers were used to evaluate the relative sensitivities of several types of detectors. The laboratory results indicate that submicrometer particulate detection is the most universal and sensitive method. Carbon monoxide detection was as sensitive as submicrometer particulate detection for pyrolyzing coal but was relatively insensitive to pyrolyzing wood or plastics. The conventional type of ionization smoke detector was the least sensitive for coal and of intermediate sensitivity for wood and plastics. Self-heating experiments with Pittsburgh seam coal piles of varying particle sizes gave ignition temperatures of 170° C for 4-to 7-µm dust, which increased monotonically with particle size. The measured heating rates were compared with data from an adiabatic calorimeter to obtain preexponential rate constants. The preexponential rate constants varied linearly with the surface area per unit mass of sample as would be expected for heterogeneous surface oxidation. The propagation behavior of ignition waves and the overall self-heating appears to depend critically on the magnitude of the convective flows induced, which counteract the depletion of oxygen in the void spaces of the pile. Classical theories of thermal ignition require substantial modification to be applied reliably to such cases.

Jan 1, 1977

By C. Golumbic

Most early research on solvent extraction of coal has been concerned with the molecular structure of coal. Although rush work is continuing, practical aspects of the subject also are being emphasized. For example, development of the Pott-Broche extraction process resulted from the discovery of very efficient solvents for the pressure-extraction of coal. Recently, Orchin and Storch reported the use of even more efficient solvents under similar conditions. In addition to the discovery of more effective solvents, the possibility of efficient extraction at atmospheric pressure is obviously of practical interest. H. J. Rose observed that phenanthrene at its atmospheric boiling point readily dispersed 80 percent or more of Pittsburgh-bed bituminous coal. This fact served as the starting point of the present investigation, ill which determination of the chemical specificity of this solvent and the chemical nature of the resulting extracts was undertaken. This paper represents a progress report of the results obtained to date.

Jan 1, 1950