Search Documents

By A. B. Hooker

The flame safety lamp with metal-gauze enclosure was invented by Sir Humphrey Davy more than a century ago, primarily for its safe light; however, it soon became the standard device for detecting the presence of methane in mine atmospheres. It still is the most widely used device for this purpose and is also the most practicable means of detecting deficiency of oxygen in coal mines. A permissible flame safety lamp is similar in all respects to one that, after a series of tests, has been approved by the Bureau of Mines as safe for use in gassy mines. However, safety depends largely upon the way lamps are maintained and used.

Jan 1, 1944

By W. K. Overbey

Surface fracture trace density, changes in roof rock type, and topographic unloading due to drainage were mapped for the mining areas located in the Blacksville-Osage, W. Va., quadrangles to investigate their influence on mine roof falls. Using these factors, a technique was developed to predict probable roof fall areas ahead of projected mining operations. As a feasibility test of this proposed technique, areas were delineated where one, two, and all three of these factors were operating to formulate a "potential hazard map" for comparison with roof fall observations that were made. The limited evidence suggests that in combination these factors are reliable predictors of where roof falls are likely to occur. This technique promises to be a useful tool in planning mining operations.

Jan 1, 1973

By Gregory M. Molinda

The Coal Mine Roof Rating (CMRR) was developed 10 years ago to fill the gap between geologic characterization and engineering design. It combines many years of geologic studies in underground coal mines with world-wide experience with rock mass classification systems. Like other classification systems, the CMRR begins with the premise that the structural competence of mine roof rock is determined mainly by the discontinuities that weaken the rock fabric. However, the CMRR is specifically designed for bedded coal measure rock. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, extended-cut evaluation, and others. It has also become truly inter-national, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. This paper discusses the sources used in developing the CMRR, describes the CMRR data collection and calculation procedures, and briefly presents a number of practical mining applications in which the CMRR has played a prominent role.

Jan 5, 2007

By W. D. Mcmillan

"Magnetic surveys made by the Missouri Bureau of Geology and Mines in 931 and 1932 disclosed a large positive anomaly about a mile south of Bourbon, Mo. 3/ Electrical resistivity measurements made by the Division of Geophysical Exploration of the Bureau of Mines in the winter of 1942-43 indicated that the source of this anomaly was in the pre-Cambrian rhyolite at a depth of more than 1,400 feet. 4/In order to determine the character of the material that caused the magnetic anomaly, which might be either a body of magnetite or a large intrusive of basic rock, the Bureau of Mines drilled four holes to depths of 1,800 to 2,300 feet. Magnetite in rhyolite porphyry was encountered at 1,600 to 2,000 feet, and this is doubtless the main source of the magnetic anomaly, although it is possible that additional iron ore exists at greater depth.Hole 1 was apparently located southeast of the source of the anomaly and encountered only small stringers of magnetite. Hole 2 penetrated four mineralized zones having a total thickness of 125.7 feet and an average weighted content of 43.52 percent iron and 31.62 percent silica. These zones were tested again by a deflection hole, 2A, which gave nearly identical indications. Hole 3, 500 feet north of hole 2, penetrated 58 foot of mineralized rhyolito containing an average 43.4 percent iron.Metallurgical tests showed that the silica in the ore is tightly locked with the magnetite. After grinding to minus 100 mesh, a 66 percent iron con¬centrate with 7 percent silica was obtained by flotation."

Oct 1, 1946

By W. T. Wertman

A research program to aid development of better petroleum-recovery technology is in progress at the Appalachian Experiment Station, Bureau of Mines, Morgantown, W. Va. The work is part of the overall effort of the Federal Bureau of Mines to effect true conservation of the Nation's natural resources. Knowledge of the magnitude of the interstitial water content of oil-bearing formations is important to petroleum-reservoir engineers because of the influence of water on fluid flow during oil production and because of the significance of water volume in oil-reserve evaluation. Such information on Appalachian oil-bearing formations is needed to aid in planning secondary oil-recovery projects. Generally, the interstitial water content of oil sands can be estimated by one or more of the following methods: Analysis of cores obtained with oil-base drilling fluid, electric logging, restored-state or capillary-pressure tests, centrifuge tests, evaporation tests, or mercury-injection tests.

Jan 1, 1959

By C. J. Chindgren

Two air classification systems were built and tested as separatory devices for recovering the nonferrous metal values from shredded automotive nonmagnetic reject scrap. A horizontal air system with a capacity up to 16 tons per hour was used to obtain preliminary separations, and a smaller capacity vertical system was used as a cleaning device. Shredded automobile reject material containing aluminum, copper, and zinc values of about $55 per ton were air-classified in the horizontal elutriator. Ninety-six percent of the metal was recovered in a 74-percent metal concentrate. Tandem operation of both classifiers recovered 92 percent of the metal in an 80-percent concentrate while rejecting 87 percent of the nonmetallics. Heavy media separation of the air-classified concentrate produced an overall recovery of 91 percent of the metal in the form of a 99-percent metal concentrate.

Jan 1, 1971

By E. W. Newman

The Bureau of Mines, in cooperation with the U. S. Geological Survey, developed the property of the Tungsten Metals Corp. by surface trenching and diamond drilling from November 1940 to June 1941 and from August 1943 to December 1943. The purpose of the work was to determine possible reserves of tungsten in the downward extension and lateral eastern extension of three major tungsten-bearing quartz veins. The property is 50 miles south of Ely, White Pine County, Nev., in the Minerva Mining District. Tungsten ore was discovered in the district in 1915, and mining started in 1916. The tungsten ore bodies occur as shoots in quartz veins that occur along faults in limestone. With the exception of a small-scale leasing operation in 1932, the property was idle from 1919 until 1936, when Tungsten Metals Corp. was organized to acquire the mines. Production ceased in May 1945, and the mines were idle until leased in 1947. Development by the Bureau of Mines during 1940 and 1941 consisted of surface trenching, sampling, and diamond drilling 37 holes for a total of 6,959 feet. Subsequent drilling of eight holes, totaling 3,067 feet, in 1943 disclosed additional reserves. This report sets forth in considerable detail the exploration work completed by the Bureau and briefly describes the mining and milling methods employed. Diamond-drill halo logs and sample analyses are shown graphically in the illustrations that accompany the report.

Jan 1, 1950

By R. B. Schluter

The objective of this Bureau of Mines investigation was to determine the effects of adding manganese compounds and ores to iron ore pellets. Manganese dioxide, carbonate, sulfate and chloride, plus six manganiferous ores from the Minnesota Cuyuna Range were tested as additives to increase the manganese content of iron ore pellets. One to 5 percent manganese, as a compound or ore, was added to five magnetite concentrates and one hematite concentrate. These concentrates were ballad, indurated (1,300° C), and tested for reducibility. Manganese sulfate and chloride were unsatisfactory additives causing cracking and degradation of the pellets during reduction. Manganese dioxide, carbonate, and the ores were satisfactory additives. The additives increased pellet compression strengths with a corresponding loss of reducibility, as compared to the pellets without manganese additions. The changes in compression strengths and reducibility were caused by the formation of Jacobite spinel and slag within the pellets. However, when the induration temperature was lowered from 1,300° to 1,200° C the reducibility and compression strengths were comparable to the pellets without manganese additions indurated at 1,300° C.

Jan 1, 1974

By A. A. Berk

Other Federal agencies have been coming to the Bureau of Mines for help with the purchase and utilization of fuel, largely coal, almost since the day the Bureau was created in 1910. The requests covered a wide range of fuel- economy problems and included boiler-water treatment after it became apparent that water-formed deposits on heating surfaces acted as insulators, decreasing heat transfer and impairing fuel efficiency. Dr. Ralph E. Hall, a Bureau of Mines physical chemist determined the 3 reactions that cause adhering scale to form in boilers (7)2 and went on to introduce scientific principles into water treatment for scale prevention (8). Widespread publicity of these achievements increased the requests for help from Federal steam-generating plants. Since no other Federal agency (even those which were more directly concerned with testing water) wanted to provide boiler-feedwater service, the Bureau decided to continue to give requested help to Federal agencies, Later, the Congress endorsed such agency cooperation as an economy measure,

Jan 1, 1963

By A. A. Berk

Other Federal agencies have been coming to the Bureau of Mines for help with the purchase and utilization of fuel, largely coal, almost since the day the Bureau was created in 1910. The requests covered a wide range of fuel-economy problems and included boiler-water treatment after it became apparent that water-formed deposits on heating surfaces acted as insulators, decreasing heat transfer and impairing fuel efficiency. Dr. Ralph E. Hall, a Bureau of Mines physical chemist determined the reactions that cause adhering scale to form in boilers (7)2 and went on to introduce scientific principles into water treatment for scale prevention (8). Widespread publicity of these achievements increased the requests for help from Federal steam-generating plants. Since no other Federal agency (even those which were more directly concerned with testing water) wanted to provide boiler-feedwater service, the Bureau decided to continue to give requested help to Federal agencies, Later, the Congress endorsed such agency cooperation as an economy measure,

Jan 1, 1963

By D. J. Stoops

The object of the research described in this paper was to investigate the effect of metallurgical and surface treatments on the corrosion behavior of arc-melted reactor-grade zirconium in cupric or ferric chloride solutions. An apparatus was constructed and specimens of various metallurgical conditions and surface treatments were tested for 6 days at 35° C., with aeration. Some correlations were observed between corrosion rate and the metal's condition and treatment, Specifically, the unattacked or least attacked specimens were those that had been etched as a final treatment before testing. The most severely attacked specimens were those that had been vacuum-annealed as a final treatment before testing. The moderately attacked specimens were those neither vacuum-annealed nor etched, but having a final surface treatment which left a cold-worked surface. Attack by cupric and ferric chloride was by pit- ting with no preference for grain boundaries, The corrosion scale was cow posed predominately of very fine zirconim particles, Particles from the FeC1,-corroded specimens were more pyrophoric than those from CuCl2-corroded specimens, and appeared to have a higher surface area to volume ratio. Comparison of results to those of previous investigators showed that at certain salt concentrations the more pure, reactor-grade zirconium was quite resistant to attack while the less pure, graphite-melted zirconium was severely attacked.

Jan 1, 1962

By D. W. Frommer

Composite samples of nonmagnetic taconite from the western Mesabi range were evaluated by reductive roasting, fine grinding, and magnetic separation to determine potential sources of concentratable material. Although large tonnages of nonmagnetic taconite are known to occur in the western Mesabi district, these materials are not as yet a commercial source of iron ore. The technique employed permits the evaluation of individual composites and blocks of composites in terms of responsiveness to a process of potential commercial significance. The 159 composites, from open-pit mines located between Grand Rapids and Chisholm, Minn., were evaluated in the following sequence: 1. Minus 8-mesh material was roasted at 500° C. in hydrogen. 2. The roasted are was ground to one or more sizes in the minus 100-to minus 400-mesh range. 3. The roasted ground ore was magnetically separated in a Davis tube. 4. Composites were classified according to degree of grinding required to produce minimal concentrates. (Minimal concentrates are herein defined as those containing less than 10 percent silica, and responsive composites as those yielding minimal concentrates.)

Jan 1, 1962

By W. P. Yant

Canister-type gas masks have become an essential part of the equipment of many industries not only for use in emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres. Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices and this bureau has become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investigations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.

Jan 1, 1932

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay and shale mining and crushing methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may, in many instances, cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, it is essential to the technical discussion and study of methods employed to consider operating costs. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scone of the cost tabulations shale ensue. The open-pit recovery of clay and shale is a comparatively simple operation in comparison with underground mining; nevertheless, it represents an appreciable factor in the cost of manufacture.

Jan 1, 1936

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (volume III) contains overall injury experience and employment data at bituminous-coal, lignite, and anthracite mines, coking plants, metal and nonmetal mines, metallurgical plants, and stone quarries in the United States for the calendar year 1956. Volume I of the Yearbook includes injury experiences and related employment data in the metal, nonmetal, and quarrying industries, and in the milling operations connected with the mining of those commodities. Volume II contains the injury and related employment experience of the coal mining, coking, and oil and gas industries. Reporting is voluntary on the surveys conducted by the Bureau of Mines to collect injury and employment data in the mineral industries, except in the coal-mining industry, where operators are required by Federal law to furnish the information requested.

Jan 1, 1958

By L. Stein

A simplified radiochemical method has been developed for quantitatively analyzing; radon gas in underground uranium mines. In this method, a measured volume of air is drawn by a pump through a drying tube and a cartridge containing dioxygenyl hexafluoroantimonate reagent. Radon is captured as n nonvolatile product. After radioactive equilibrium has been established between radon and its short-lived daughters (approximately 4 hours), the gamma-emission of the cartridge is measured with a scintillation counter. The amount of radon is then calculated from the gamma-emission rate. The effect of cartridge geometry, reagent load, and air flow rate upon collection efficiency and counting efficiency is reported.

Jan 1, 1977

An accelerated and coordinated program of coal research is believed by many to be a necessary step in assuring coal's proper position in the expanding energy market. The President's Advisory Committee on Energy Supplies and Resources Policy, for example, made the following recommendation: We recognize that coal is a great national asset and endorse a cooperative study to determine what research and development could be undertaken. The coal industry and both Federal and State Governments should participate in this study and its costs. Representatives of the coal industry have agreed that such a study should be initiated. Accordingly, Felix E. Wormser, Assistant Secretary - Mineral Resources, United States Department of the Interior, requested the Bureau of Mines and Bituminous Coal Research, Inc., to conduct a survey of current research on bituminous coal. In addition to this survey, studies were made to determine research projects that would be of value to the coal industry.

Jan 1, 1956

By A. J. Kraemer

Few important improvements other than the development of cracking processes were made in technical petroleum refining from 1914 to 1919. Refiners were concerned mainly with enlarging their plants and erecting new plants to meet the growing demand for petroleum products. Shell stills operated as a unit or arranged in series for progressive or continuous distillation were the prevailing distillation equipment. Some improvement was made in condensers, but in most refineries of the period coils of pipe immersed in tanks of water were used to condense vapors and cool liquid products of the stills. Heat exchangers to conserve heat and reduce costs were more highly developed at California topping plants than at other plants. In this connection Wadsworth3/states: It is regretted that information concerning the operation of topping plants with eastern and Middle West oils is not available. The writer carefully canvassed the Middle West, but did not find a plant where operation had progressed beyond the early experimental stages and reliable figures could be furnished.

Jan 1, 1941

Exposure to airborne respirable crystalline silica dust can lead to silicosis, a debilitating lung disease. On surface coal mining and construction sites, blast hole drills are notorious sources of airborne respirable dust that may contain significant amounts of silica. The drill operator and drill helper usually receive the greatest silica exposure compared with other occupations. As a result, many drilling operations have been, and still are, on more stringent dust standards. Drilling through various rock formations naturally presents a strong potential for silica dust generation for several reasons. First, drilling is a pulverizing process that generates large amounts of very small dust particles. Second, the bailing air used to flush cuttings from the hole leaves the hole at a very high velocity and can be difficult to contain. Third, many fixed shrouds used to enclose the area beneath the drill deck have a significant amount of leakage due to 1) gaps between the shroud and ground created by raising/leveling the drill, 2) gaps in the corner seams, and 3) tom deck shrouds. CONTROLS A dry dust collection system is typically connected to the drill deck to collect dust as the bailing airflow transports the cuttings (and significant amounts of airborne respirable dust) out of the drill hole. Deck shrouds are installed in an attempt to enclose the volume around the drill steel and prevent dust escaping. However, most deck shrouds are rectangular and constructed of four separate pieces of rubber belting attached to the deck. Because of this design, there is usually a significant amount of dust escaping from the open seams as well as the open area between the shroud and the ground. This dust can be a significant source of silica exposure to drill operators as well as other personnel downwind of the drill.

By C. T. Anderson

In July 1947, the U. S. Bureau of Mines, in cooperation with the Air Materiel Command, started an investigation of zirconium alloys with the object of determining the suitability of such alloys for high-temperature applications. This report covers the preliminary study of about 25 zirconium-rich alloy systems with respect to preparation, fabrication, tensile properties, metallographic structures; constitution, and heat resistance. Obviously, each system could not be investigated thoroughly, and this publication can be regarded only as a first approach. The more promising individual alloy systems will be studied in greater detail and reported in subsequent publications. The study of zirconium alloys on such a scale has been made possible by the U.S. Bureau of Mines developments in the past 5 years On producing zirconium metal. This basic process is similar to that developed by Kroll for producing ductile titanium metal and consists essentially of reducing zirconium chloride by means of molten magnesium. The Northwest Electrodevelopment Laboratory at Albany, Oreg., has produced several thousand pounds of ductile metal in this manner and has a pilot plant producing over 300 pounds of metal per week. Alloys were prepared by melting Bureau of Mines zirconium and the best available grade of alloying element in graphite, with suitable provisions for preventing oxidation. The ingots were quartered longitudinally and sheath-swaged at 850° c. to 3/8-inch diameter rod. Two of those rods were send to Wright Field for room-temperature and 1,200° F. tensile properties. The remaining two sections were used for metallographic, hardness, heat-treatment, and heat-resistance studies. The salient features of this investigation are summarized in table 1.

Jan 1, 1950