Search Documents

By J. F. Barkley

[There is a general concept in the, coal trade that the moisture- and ash-free B.t.u. of coal from the same seam, and. surely from the same mine, is substantially a constant; that calculation of the -moisture- and ash-free B.t.u. value from the proximate analysis and B.t.u. determined in the laboratory will reveal whether a coal came from a given area or sears; and that, having this constant, the B.t.u. value of a coal sample can be calculated fairly closely upon a dry or as-received basis from the moisture and ash values of its proximate analysis.]

Jan 1, 1941

By D. Harrington

When the word "gas"' is mentioned in connection with mining almost invariably it is inferred that the explosive gas, methane, is in mind and that the reference is to coal mining. Although methane is likely to occur in any coal mine the metal mines of the world contain by far a greater variety of gases than do the coal mines. Often the gases in metal mines are as dangerous as the gases likely to be found in coal mines, and sometimes are even more deadly. A coal mine is more likely to contain methane than a metal mine. In rare instances it may contain high percentages of nitrogen or carbon dioxide or it may be deficient in oxygen where the air is confined in a blind end or in a sealed region. Much more rarely relatively small percentages of ethane or other hydrocarbons with an odor of ether, gasoline, or kerosene, or minute percentages of hydrogen sulphide are found in a coal mine. During a coal-mine fire or explosion carbon monoxide content is likely to be high (4 per cent or more), and if the coal contains much sulphur the high fumes may contain some sulphur dioxide.

Jan 1, 1931

By J. G. Walters

This report presents the results of an investigation in Which the chloroform solubilities of coals and chars are related to rank, temperature of thermal treatment, time at a given temperature, vacuum thermal treatment, plasticity, oxidation, blending, and mass spectral analyses and molecular weights of the extracts. It was found that the quantity of chloroform extract obtained from chars can be altered by creating a vacuum above the charge during preparation of the char, increasing the time at temperatures within the plastic temperature range, and by utilizing different rates of heating to attain a given temperature. Relationships found between the chloroform solubilities of chars produced at temperatures within the plastic temperature range and the relative fluidities in this temperature range indicate that the chloroform-soluble portion of the char is a significant component of the plastic mass. Chloroform-extract yields from chars made from blends of coals cannot be calculated from chloroform-extract yields obtained from chars made from the component coals.

Jan 1, 1967

By R. J. Burgess

During World War II the shortage of ore revived interest in eastern iron deposits, among which -!2..c "Ile Massachusetts and Connecticut limonites. The Cheever mine, in the Richmond-Salisbury area of Massachusetts, was formerly a large producer of limonite ere. The Bureau of Mines investigated the lateral and downward extensions of the Cheever ore body, which was mined from about 1850 to 1892, by ap open cut 1,000 feet long and also by underground workings. even holes aggregating 1,723 feet, were drilled by the Bureau during the winter of 1943-44. They comprised three diamond-core drill holes, two churn-drill holes, and two rotary-drill holes. A geophysical survey of the Cheever mine area and adjoining ground was made in conjunction with the drilling program. Although this survey did not locate the limonite ore beds, the data were of considerable assistance in locating the limestone contact which forms the footwall of the ore beds. Drilling disclosed two beds of limonite with a heavy overburden of glacial till.

Jan 1, 1949

By J. S. Dunning

Recent developments in energy conversion, mining and minerals processing, pollution control, and chemical equipment have placed in-creased demands on heat-resistant alloys. Higher corrosion rates from oxidation, hot corrosion, and sulfidation have increased consumption of materials that contain critical and strategic minerals and in many cases have limited productivity. The Bureau of Mines is conducting re-search on substitute materials having greater resistance to high-temperature corrosive atmospheres above 6000 C compared to austenitic stainless steels such as AISI 304, 316, and 310, with the goal of conserving critical metals such as Cr and Ni. The substitute materials are based on Fe-Cr-Ni-Al compositions. Aluminum additions to Fe-Cr-Ni alloys significantly improve high-temperature corrosion resistance, particularly sulfidation resistance. In the alloy, devised by Bureau researchers, aluminum additions are held in the form of a second-phase precipitate, 8NiAl. Minor additions of Ti, Mn, and Si improve workability.

Jan 1, 1984

This chapter presents proportionate mortality ratios (PMRs) derived from death certificate data in the National Occupational Mortality Surveillance (NOMS) database for the years 1986 through 1993. At the time this report was prepared, 1993 was the latest year for which data were available. Industry is classified under the 1980 U.S. Bureau of the Census classification system [Bureau of the Census 1982]; cause of death, under the International Classification of Diseases, Ninth Revision (ICD-9) [World Health Organization 1977]. A PMR of 100 indicates a mortality risk for a particular industry group that is similar to that for all industry groups combined. A PMR over 100 suggests a higher risk; a PMR under 100 suggests a lower risk. PMRs are subject to many factors that affect their reliability and validity and may not be comparable across populations with very different causes of death. An elevated PMR for a specified cause of death among an occupational or industry group may indicate a relationship between a work exposure and the cause of death specified. However, there are many limitations of PMRs as a measure of risk; they are most useful for generating hypotheses about exposure-disease relationships, which can then be tested in other studies. Selected PMRs are presented separately for males and females for coal mining, metal mining, nonmetallic mineral mining and quarrying (which includes nonmetal, stone, and sand and gravel), and for oil and gas extraction. All PMRs have been adjusted for age and race. In general, PMRs are presented only if the lower 95% confidence limit exceeded 100. If a PMR in an ICD-9 subcategory was above 100, however, the PMR for the larger category into which the subcategory falls is always presented and may be less than 100. PMRs can be expected to be elevated for conditions that have a high prevalence in particular occupational groups. PMRs showed elevated values for conditions known to affect miners, such as coal workers' pneumoconiosis, pneumoconiosis due to silica, tuberculosis, chronic pulmonary heart disease, and injuries. Additional findings of interest were- • An elevated PMR for myocardial infarction among male coal miners (table 2-1); • Elevated PMRs for neurologic disease in general and anterior horn cell disease, in particular among male metal miners (table 2-3); • An elevated PMR for rheumatic heart disease in male metal miners (table 2-3); • Elevated PMRs for malignant neoplasms of the digestive organs and peritoneum and for malignant neoplasms of the colon and rectum in female nonmetal miners (table 2-6); and • Elevated PMRs for non-A, non-B hepatitis and arteriosclerotic heart disease among male oil and gas workers (table 2-7).

Jan 5, 2000

By S. S. Peng

Successful longwall mining requires a good roof control. A good roof control implies that: (1) no excessive pressure is build up in the face powered supports, and (2) chain pillars are designed in such a way that panel entries are well protected and interactions between adjacent panels are minimized. A clear understanding of strata behavior around longwall panels due to face movement is, therefore, the foremost requirement for achieving better roof control. This dissertation is designed to analyze the effects of strata behavior on longwall panels due to the mining activities. The following topics are studied: (1) the weighting, phenomena and their effects on front abutments, and (2) the chain pillar stability and pillar design under various roof conditions. Three dimensional finite element analysis was employed. The effect of parameters such as overburden depth, mechanical properties of the immediate roof and main roof, panel width, and size of chain pillar on (t) and (2) were analyzed. Four typical models were utilized to simulate various phases of panel extraction under various combinations of the above parameters; model one is to simulate the beginning of panel mining; model two is to simulate the situation that longwall face has passed more than half of panel length; model three is to simulate the completion of panel production; and model four is to simulate the second panel mining. The following formulae have been developed by applying multiple regression model to analyze the finite clement results: (1) a formula that classifies the type of root strata at the face area. (2) formulae that predict the first weighting and periodic weighting lengths. (3) a formula for design of the chain pillar size. Case studies were performed to check the validity of the formulae proposed. Comparison of the formulae proposed for the chain pillar design with other formulae were also performed.

Jan 1, 1984

By Frank G. Schwartz

VARIABLES OF composition and environment affecting storage stability of gasoline-type fuels were studied, utilizing radioactive tracers and other analytical techniques. Changes in gasoline composition brought about by aging were determined and correlated with gum formation. The amounts of reaction of selected gasoline components, measured by radioactive tracers, were determined in a gasoline-type blend and in a mixture of 17 selected pure gasoline components. The data show that sulfur compounds, nitrogen compounds, polycyclics, and olefins enter into gum-forming reactions. Certain sulfur and nitrogen compounds were found to be most reactive in the gum-forming process. Results of this study indicate that the aromatic constituents of gasolines may contribute substantially and directly to gum formation. A mixture of tetralin and indan-type compounds is reactive, and this mixture appears to be the main aromatic portion entering into gum formation. A secondary but significant amount of naphthalenes also appears to have reacted in the gum-forming process. Analyses of the sulfm compounds in a fresh and an aged fuel indicated that elemental sulfur, hydrogen sulfide, thiols, sulfides, and disulfides were depleted during aging, but thiophenes and residual sulfur compounds were not depleted by fuel deterioration.

Jan 1, 1964

By Byron E. Blair

This report describes procedures for using a high-speed camera to study blasting phenomena. Both quantitative and qualitative information can be obtained, provided that proper interpretations of the projected two-dimensional images are made. Geometrical relationships between object and image displacements are given in terms of horizontal and vertical angles of the camera optic axis with respect to the quarry face. Correction factors are given for obtaining true object displacements from image displacements in the camera film plane. The time of initial rock movement also is considered, and the control-ling factors of camera speed, scale factor, minimum increment of projection measurement, etc., are evaluated in terms of minimum time intervals. The high-speed camera and associated equipment are described, and field measurements and laboratory data analysis techniques are outlined. An analysis of a typical high-speed motion picture is made, and the application of the necessary correction factors is illustrated.

Jan 1, 1960

By G. W. Jones

Gas analysis is of great practical value to the combustion engineer as a guide in the proper deli and operation of power and heating plants. The automotive industry, however, has made little use of gas analysis in the design and construction of engines. Tests4 made by the Bureau of Mines have shorn that for the average motor vehicle approximately 30 per cent of the heat value of the gasoline passes out in the exhaust as incomplete-combustion products. The tendency at present is to pay more attention to ease and flexibility of operation than to efficiency of combustion. However, neither condition can be fully realized except where each cylinder gets a mixture of the same composition - that is, when certain cylinders do not "load up" with gas at the expense of the others. When this occurs, due to some of the cylinders having too rich a mixture while in others it is too lean, it is impossible to get efficient combustion from the fuel used. Gas analysis enables the engineer to determine the quality of the mixture fed to the different cylinders with a high degree of precision. Briefly, the method consists in making an analysis of the exhaust gas from each cylinder while the engine is in operation.

Jan 1, 1924

By Frank A. Peters

The Bayer process treating Jamaican bauxite was evaluated from an economic standpoint, using standard estimating methods and published data, to present a reference point for cost estimates for nonbauxite alumina processes. The estimated operating cost for a plant producing 1,000 tons of alumina a day is $47.96 per ton of alumina when charging $8 per ton for bauxite and $2.30 per hour for direct labor. The estimated fixed capital cost is $46 million.

Jan 1, 1966

By R. C. Buehl

Pilot-plant tests have been in progress at the Bureau of Mines, Pittsburgh, Pa., on the recovery of manganese from open-hearth slag.3/4/5/ In the process, 1 the slag is first reduced in a blast furnace to make a high-phosphorus spiegeleisen containing 12 to 22 percent manganese. A slag containing 55 to 60 percent manganese is made from this spiegel by oxidation in a basic-lined converter. The metal from this blowing operation contains about 3 percent phosphorus, 1 percent manganese, and less than 1 percent carbon. Economic efficiency in the manganese-recovery process requires that this metal be converted into steel. Because of its high phosphorus content the metal is suitable for blowing in a basic-lined converter. In most of the tests described in this report, metal of this composition was used as the starting material in a 1-ton, side-blown, basic-lined converter. Although basic-lined converters are not used for steel production in the United states, in Europe a considerable portion of the steel is made in them. Open hearths largely have replaced converters for steelmaking in the United States; mainly because open-hearth steels have better physical properties than converter steels because of lower nitrogen and phosphorus contents. However, by improving converter design and operating technique during the past 15 years, metallurgists have found that low-nitrogen steels with physical properties equal to open-hearth steels can be produced in converters.6/ Tests at Jones & Laughlin steel Corp. with side-blown, acid-lined converters of 3 and 22 tons capacity showed that steel with a low nitrogen content comparable to that of open hearths operating on scrap charges could be made by surface blowing.7/

Jan 1, 1955

By Arnold O. Tanner

The recession that took hold of the domes-tic mining industry in 1981-82 finally abated somewhat in 1987, resulting from increases in many commodity prices, especially in the metals sector, and from continuing success in lowering operating costs. By no means was the work finished; the mining industry was in a sense entering a new era. The struggle for survival was still very evident for many companies and various commodities, but increasing productivity and profits were accompanied by indications that these trends were more long term than short term. Raw nonfuel minerals produced in the United States during 1987 had an estimated value of $26.3 billion, an increase of $2.9 billion over the 1986 value. This is the fifth consecutive year that the value has increased. Except for a decrease in 1982, the value each year has increased since 1971, or 15 of 16 years. The value of raw metals production increased by an estimated 28%, an impressive improvement since the drastic fall in 1982. Industrial minerals growth was comparatively flat, with an estimated in-crease in value of 0.1 %, continuing a trend of the previous 2 years. Metal mine production dropped considerably in 1982 and maintained its resultant lower level until 1987, when production significantly recovered.

Jan 1, 1989

By F. R. Lee

THE Bureau of Mines was established in July 1910 to conduct research and to establish standards for mining equipment and practices which would conserve human life, natural resources, and property in the mineral industries. Several lists of equipment approved by the Bureau as permissible for use in gassy coal mines have been issued since then. The lists covering all approved equipment except breathing apparatus and explosives have born consolidated into two publications: Bulletin 343. Permissible Equipment Approved to January 1, 1953, and Information Circular 8220, Permissible Mina Equipment Approved By The Bureau of Mines During 1953-62. The, purpose of this publication is to supplement Bulletin 343 and Information Circular 8220 with a listing of permissible equipment approved during 1963 and 1964. The schedule, (standards) under which equipment listed herein have been approved are, as follows (cities and dates of approval and revision are, given in footnotes) : Schedule 2F,3 schedule 6D,4 schedule 7C,5 schedule 8C,6 schedule 9B,7 schedule 10C,8 schedule 12D,9 schedule 22,10 schedule 24,11 schedule 25B,12 schedule 25B,13 schedule 29A,14 schedule 30,15 and schedule 31.16

Jan 1, 1966

By Edward C. Peterson

Recent studies indicate that the United States halt substantial reserves of ilmenite, one of the major titanium minerals. However, the studies showed that sources of rutile, another important source of titanium are limited. This paper summarizes and evaluates results and conclusions reached by the various investigations initiated by the Bureau of Mines and others pertaining to the titanium mineral resources of the Nation. Domestic occurrences of ilmenite that are economically exploitable by present-day beneficiation methods are found in Florida, New Jersey, New York, South Carolina, and Virginia. These deposits are estimated to contain 50.3 million tons of titanium dioxide (TiO2). Occurrences of ilmenite that cannot be processed economically under present technological conditions are found in California, Colorado, Minnesota, Montana, Oklahoma, Oregon, Rhode Island, and Wyoming. These reserves amount to 51.1 million tons of TiO2. Reserves of rutile found in the United States are estimated to be 1.8 to 2.1 million tons of TiO2. Other than occurrences in Florida and South Carolina, rutile is found either in small scattered bodies or in deposits where the mineral cannot be recovered economically by present beneficiation methods.

Jan 1, 1966

By K. F. Anderson

The increasing number of oil-productive reservoirs in the Ellenburger formation has emphasized the need for information pertaining to the hydrocarbon recoveries that may be obtained from such reservoirs. Most of the space available for accumulating hydrocarbons in the Ellenburger formation is derived from fractures, which makes it difficult to estimate reserves or probable recoveries. The Ellenburger reservoir in the Big Lake field was selected for study because it is one of the few near-depleted reservoirs in the area. The experience gained in operating and developing this reservoir has been and should continue to be a helpful guide to operators both in predicting recovery and establishing methods of development and operation In similar reservoirs. Development and production data were gathered from different sources. The writers have compiled and interpreted these data to estimate the ultimate recovery of hydrocarbons. In addition to the estimates of ultimate recovery, the report contains sample calculations and estimates of theoretical recovery based on different methods of operation. The calculations presented in this report indicate that the Ellenburger reservoir is 95 percent depleted and that the ultimate recovery of hydrocarbon liquid from the oil reservoir and gas cap combined will he 4-0 barrels per gross acre-foot of reservoir rock. An estimated 32 barrels of condensate per gross acre-foot of reservoir rock in the gas cap has been recovered, and the estimated ultimate recovery of crude oil will be 47 barrels per gross acre-.foot of rock in the crude-oil reservoir.

Jan 1, 1954

By N. L. Wimmler

"INTRODUCTION The Southern Cross district in Deer Lodge County, Mont., has been chiefly a gold producer. Most of the production has come from gold-bearing hematite-limonite ores. Some of these ores were mined and shipped to smelters for use as flux in smelting copper ores. A magnetite deposit in the Pomeroy property, containing no gold or other economic nonferrous minerals, was mined from 1921 to 1923, the ore being shipped to smelters for flux.The iron-bearing deposits in the Southern Cross area were examined by Bureau of Nines engineers/ on June 28, 1943, and October 14, 1943. As a result, a Bureau exploration project was recommended; it was conducted during 1944. A magnetometer survey was first made of the magnetite-bearing area at and in the vicinity of the Pomeroy property. Exploration by diamond core drilling was then conducted within this area, and in the Southern Cross and Hold Fast properties. The cyanide tailings dump at the Hold Fast mill was sampled by auger drilling.This report presents the data obtained by the Bureau of Mines exploration."

Dec 1, 1946

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag compositions. The present report deals with the CaF2-Y203 system for which solidus and liquidus temperatures and solid solubilities were determined. The information is presented as the phase diagram. All specimen compositions were blended from high-purity materials and encapsulated in Mo or Pt20Rh prior toheat treatment. Liquidus temperatures were determined by ceramographic examination of heat-treated and quenched specimens. Solidus temperatures were determined by differential thermal analysis and by electron microprobe analysis of quenched specimens. Terminal solid solubilities were derived by parametric methods. The peritectic system was found to be pseudobinary due to the formation of yttrium oxyfluoride at temperatures near the liquidus. The peritectic point occurs at 7 mole pct Y203 and 1,438° ± 5°C. The terminal solid solubility of Y203 in CaF2 decreases from 7 mole pct at 1,438° C to 1 mole pct at 1,100° C, and the solubility of CaF2 in Y203 decreases from 9.5 to 7 mole pct over the same temperature interval.

Jan 1, 1970

By B. H. Clemmons

A field method has been devised for rapid determination of heavy minerals occurring in the unconsolidatod beach and dune sands. The method has been proved practical by usage in field evaluations of several hundred beach- and dune-sand samples in the Florida area. The simple equipment required and the techniques involved are described. Other data show that the method is relatively insensitive to variations in the mineralogical content or size distribution of the mixed heavy minerals contained in the samples tested. A modification of this procedure, found to be suitable for plant use in determining the relative purity of heavy-mineral flotation concentrates, is also described. A specific application is determination of the amount of feldspar-quartz in spodumene flotation concentrates. The results of the rapid evaluation techniques closely approximate those obtained by more precise laboratory procedures.

Jan 1, 1957

By G. A. Bole

"This paper presents a review of the literature and is an epitome of work acne and articles published by Schurecht, Robson and Andrews', in the investigation of the feasibility of making basic refractories from dolomite, was carried on successively by these men, at the Ceramic experiment Station of the Bureau of Mines, Columbus, Ohio.Scope of the work.The dolomite refractories investigation of the Ceramic Station includes a study of the many fluxes which could be used to aid in the dead-burning of dolomite and also a complete survey of the iron oxide-alumina-silica field as fluxes. The temperature of calcination and the resulting properties have been carefully investigated, and the most desirable calcines chosen for further investigation in the making of dolamite bricks. Many binders and the several methods in common use of fabricating bricks commercially were tried, and a thorough study was made of the properties of the most successful ware,Previous Investigators.Even before the World War, considerable work was done on dolomite this war greatly accelerated the efforts of the many Investigators."

Jul 1, 1924