Search Documents

By Peter H. Toepfer

Hydraulically emplaced, classified mill sands long have been used for stope fill. Entrained water drains rapidly from this type of fill through openings between the sand grains. Slimes are removed to facilitate drainage of the water, thereby lowering dangerous hydrostatic pressures in the fill. Use of unclassified mill tailing as practiced at the Dayrock mine is a recent development and represents a fundamentally different approach to the problems of inhibiting the development of hydrostatic pressures within the stope fill. At the. Dayrock mine, mill tailing is used to form a densely packed fill of sand and slime particles relatively impervious to additional water.

Jan 1, 1952

By William R. Wessels

This report describes a field survey and laboratory investigation into the causes of failure of resiliently clad screen decks applied to coal preparation plants. Blinding of screen deck perforations and delamination of the resilient cladding are studied and mechanisms responsible for these failure modes are hypothesized. A laboratory test program to simulate the mechanisms was begun and abandoned when it became apparent that meaningful test results would require a substantially redirected effort. No meaningful test data was obtained from the laboratory simulation.

Jan 1, 1982

By W. M. Merritts

A joint investigation by the Bureau of Mines and the Christopher Coal Co. at the Humphrey No. 7 mine, operating in the Pittsburgh coalbed in northern West Virginia, was undertaken to gain more insight concerning the hazardous emission of methane gas in mining, This report describes the equipment, procedure, and results. Horizontal bleeder holes drilled in the faces drained large quantities of methane, eliminating downtime of mining equipment. Also, larger quantities of methane were removed by forcing 14 to 25 g.p.m. water at 25 to 200 p.s.i. 5 pressure into the bleeder holes, In one infusion test a fluorescein dye was added to the infusion water; in later mining operations, the infusion water was traced for a distance of 1,500 feet. With vacuum pump applied to the horizontal hole the gas-flow rate increased, and the methane content decreased.

Jan 1, 1962

By H. B. Hill

The Salt Flat field, formerly called the Joe Bruner field, is located northeast of the town of Luling in Caldwell County, Tex. This field, which is a fault structure, approximately parallels and is about 5 miles east of the Old Luling field. The proved area is approximately 1,280 acres, on which 332 producing wells (September, 1930) have been drilled. The majority of the wells are producing from the Edwards limestone at an average total depth of 2,700 feet. A few wells are producing from the Austin chalk or from other formations above the Edwards limestone. The Wilcox formation is exposed, and the fault trace in places is scarcely evident. The strike of the structure is approximately N. 20 to 45° The displacement of the fault is probably 200 to 500 feet. The discovery well was completed in the Austin chalk by the Lutex Oil Co. during April, 1928. In October, 1926, the Sun Oil Co. completed the discovery well in the Edwards pay. This well was an important discovery, as it indicated the potential oil possibilities of the Edwards limestone in echelon fault structures. The discovery led to the development of the third fault field in the Edwards limestone and opened up a large area for future prospecting.

Jan 1, 1931

By Arnold B. Hubbard

A thermal decomposition study of the kerogen in three Colorado oil shales was made at different temperatures by heating the shales in the absence of oxygen at atmospheric pressure and measuring the decomposition products (gas, oil, and bitumen) formed. From these data the specific reaction rates, "k", for the thermal decomposition of kerogen were determined for each temperature studied, making it possible to calculate the time required to accomplish a given amount of decomposition within the temperature range. The influence of temperature on reaction rates was presented by plotting the data according to the Arrhenius equation, thus providing a means of estimating the values of "k" for any temperature within the range of this study. It was found that the specific reaction rates for the thermal decomposition of the kerogen in the three sampler were comparatively equal at corresponding temperatures.

Jan 1, 1950

By Pamela J. Watson

The U.S. Bureau of Mines has demonstrated in laboratory tests that drilling with surface-charge-neutralizing concentrations of polyethylene oxide (PEO) polymer solutions simultaneously improves penetration rates and extends bit life. The applicability of this additive to improve drilling performance in coal measure rocks was demonstrated under field conditions at an abandoned mine land site in Pennsylvania and a producing coal mine property in Ohio. Penetration rate improvements ranging from 15 to 50 pet were obtained when core drilling through a variety of coal measure lithologies. Drilling cost analysis indicates that the small added cost of using the polymer is more than offset by the savings that result from demonstrated increased drilling penetration rates, which translate into drilling cost savings of about 10 to 30 pct. This report also gives chemical analyses of a variety of coal measure rocks and some corresponding local drilling water samples, obtained from a wide geographical base, along with threshold concentrations of PEO required to effect the improved drilling performance in these rocks. From these data, the threshold PEO concentrations needed to ensure improved drilling performance can be estimated for any coal measure rock suite. Proper techniques for mixing PEO solutions are also presented.

Jan 1, 2010

By Thomas Jenning, C. M. Keithly

"INTRODUCTION This report is one of a series. 4. 5. 6/ concerned with presenting historical development, and operating data on secondary-recovery projects in various States to stimulate interest in sound secondary-recovery programs. Preceding reports in this series have dealt exclusively with descriptions of and results obtained by water flooding in three states, but no recent publication of comparable purpose describes gas-injection 7/ practices. The authors intend to present material relevant to the development and operation of gas-injection projects in Illinois, with particular emphasis on those producing from oil-bearing horizons that had been depleted to a point near the economic limit of operation by past oil-recovery methods.Most operators realize that the energy expended on the movement of fluids through gas-expansion- or gas-cap-type oil reservoirs to producing wells must be supplemented to attain maximum recovery of the oil present. Under favorable conditions, many operators choose to maintain oil-propulsive forces at or near their original magnitude by injecting extraneous fluids into a reservoir or recycling produced fluids early in the life of a field. More common, and less desirable, is the practice of replenishing these forces after primary producing methods become unprofitable. The lattes practice has been adopted in many stripper fields in Illinois and most of the oil-producing States during the last 40 years, but other old oil fields, and oil properties within those fields which were partly exploited by secondary--recovery methods, also may offer favorable opportunity for further development. To encourage and, aid operators in the development of gas-injection projects in the old oil fields of the United States, four projects have been described in detail in this report."

Nov 1, 1944

By D. S. Burgess

An investigation of the hazard of spillage of liquefied natural gas (LNG) onto water is described. About 2,000 gallons of LNG were consumed in various tests. The initial vaporization rate of LNG following spillage was found to be 0.037 lb/ft2 sec; when the spill was confined, this vaporization rate was moderated after about 20 seconds by the growth of an ice layer on the water surface; when the spill was unconfined, a coherent ice floe was not observed and the vaporization rate was essentially time independent. The maximum diameter (in feet) of the spreading LNG pool was found to be given by 6.25 Wo 1/3, where Wo is the weight of LNG in pounds, Downwind of a natural gas source, time-averaged methane concentrations were given in good approximation by standard air pollution equations. However, peak concentrations were as much as twentyfold higher than average, adding an additional factor to the assessment of hazard. The effect of layering by the cold vaporized natural gas was similar to the effect of a temperature inversion on normal gases in the atmosphere. Small-scale explosions were observed on pouring LNG onto a water surface; no single explanation seems pertinent to all of the incidents observed.

Jan 1, 1970

By Arne Landsberg

A study of the chlorination kinetics of germanium, silicon, iron, tungsten, molybdenum, columbium, and tantalum has been made to determine the effects of temperature, chlorine concentration, geometric surface area and gamma radiation. The reaction products were volatile at the temperatures used this making it possible to follow the reaction rates by weight loss of the solid. Chlorination rates of germanium, silicon, and iron were found to be directly proportional to chlorine concentration while the rates for tungsten, molybdenum, columbium, and tantalum were proportional to the 0.5 to 0.6 power of chlorine concentration. A good correlation of reaction rate and geometric surface areas was not obtained because the true surface area of the samples could not be measured. Intense gamma radiation had no effect on reaction rates. The Arrhenius activation energies determined over the temperatures used are as follows: Germanium, 27 kcal/mole (233°-241° C); silicon 33 kcaL/mole (375°-517° C); iron, cold rolled, 20 kcal/mGle (259°-325° C) annealed, 21 kcal/mole (293°-337° C); tungsten, 43 kcal/mole (617-776° C); molybdenum, 37 kcal/mole (445°-4910 C); columbium) 34 kcal/mole (229°?255° C); and tantalum, 29 kcal/mole (370°-449° C).

Jan 1, 1965

By George Quackenbos

The principal objective of this Program is the design, fabrication and testing of an Environmental System for operation in underground mines, to assess the effect of various mining systems on the contaminant levels near the mine face and within return airways. In order to determine the effect on airborne contamination in mines resulting from the development of new mining techniques, equipment and control systems, a Comprehensive Monitoring System is required to assess such contamination levels at critical and strategic locations and relate this information with ventilation parameters. The three variables to be sensed on a continuous basis are airborne dust concentration, methane concentration and ventilation air velocity. Each Monitoring Station will consist of a self-contained unit containing a power source and sensors to monitor the three above mentioned parameters. Ruggedness, reliability, ease 'of operation and intrinsic safety are important design objectives. Data gathered by each Monitoring Station will be fed to a Central Data Acquisition System by means of a portable transfer unit.

Jan 1, 1982

By W. C. Phalen

"Tho the term “magnesite” is generally applied to the iron-bearing carbonate of magnesium, such as is found in Austria and Hungary, by some Austrian magnesite is referred to as bruennerite. The mineral bruennerite has become of commercial importance only in Austria. The important deposits are found in Styria, lower Austria and northern Hungary. It is of interest to know that the world's largest deposit of spathic iron ores or iron carbonate (FeCO3), occurs at Eisenerz, Styria, while the world's largest deposit of spathic bruennerite is found at Veitsch in the same province.The Styrian and lower Austrian deposits are located much nearer the Adriatic sea than are the deposits of northern Hungary; and it is from the former that most of the exported magnesite has come. They are located south-west of Vienna, and extend west from Semmering thru the Murz Valley to Tyrol. The chief deposits reckoning from east to west are those of Semmering, Veitsch, Breitenau, Trieben, Radenthein, and Dienten.The largest and most important deposit is that at Veitsch located near Mitterdorf, on the South Austrian railroad in the Murz Valley, Styria. Here the magnesite, which occurs in the form of a lens is quarried on the slope of a hill in a series of terraces about 50 feet apart. The entire work extends thru a vertical distance of 500 feet. The huge magnesite lens is nearly 4 of a mile long and over 1,000 feet in width, and probably extends to a considerable depth.The formation containing the magnesite extends eastward beyond Vienna into Northern Hungary where magnesite is quarried beyond Jolsva and Nyustya in the Gomor district. In spite of the remote location of these deposits as compared with those in Styria, magnesite was shipped from them before the war a distance of 360 miles to the port of Fiume for overseas shipments to other parts of Europe and to America.The average analysis showing the composition of the Austria-Hungary mineral is as follows:The magnesite occurs as lenticular masses in a belt of Carboniferous rocks consisting mainly of metamorphosed Shales, sandstones, conglomerates,,and limestone, It is grayish in color when fresh, and contains sufficient ferrous carbonate to blacken it when calcined. It turns brown owing to the oxide ion of the ferrous carbonate when exposed to the air. The quantity of carbonate of iron is ariable and different analyses show that it ranges up to 13 or 14%For the most part, only the sintered article has been imported into The United States. This material has achieved an enviable reputation for its uniformity both as to chemical and physical characteristics. The homogeneity of the sintered Austrian magnesite is doubtless due in part to the averaging effect of the different operations, such as crushing, dressing, sintering, And mixing, n effect which is not obtainable in mere hand samples.There is comparatively little variability in the sintered magnesite as marketed, and five analyses of this sintered magnesite as quoted by Cornu* are gas follows:"

Aug 1, 1919

By J. B. Rosenbaum

This report presents new findings and consolidates previously published data to provide a single reference containing a concise and comprehensive description of the Bureau's work on electrolytic chromium. Two separate systems for electrolytic-chromium recovery were developed, one designated as the oxidized system the other as the reduced system. The electrowinning of chromium metal follows the dissolution of chromium from the ore or from ferrochrome and its separation from gangue and metallic impurities. Chromite was first solubilized by pressure digestion at slightly elevated temperatures in an oxidized acid solution using Na2Cr2O7 as an oxidizing agent. Later it was found that a sodium-free electrolyte was preferable, using return-cell anolyte containing H2SO4 and Cr03 as the oxidizing agent. Gangue materials were separated from the soluble metallics by filtration; and, after the Cr+3 had been stabilized, the metallic impurities were separated as crystalline ammonium salts by vacuum crystallization.

Jan 1, 1957

By Maria I. De Rosa

Analysis of mining equipment fires from 1990 through 1999 reveals that there were 340 large mining equipment fires, resulting in 72 injuries and five fatalities. Many of the fires resulted in the loss of equipment and all posed potential or real risks to the operator. In 97 cases, the fires raged out of control due to engine shut­off failure, even upon activation of the machine fire suppression system, due to the spraying of pressurized hydraulic flu­id and fuel onto hot engine surfaces. In other cases, even after engine shutoff, the fires re-ignited, fueled by the contin­ued flow of flammable fluids remaining in the lines onto the hot engine surfaces. In many of the fires, flammable vapors evolved and penetrated the cab, violently igniting, forcing the operator to exit under very hazardous conditions. The use of emergency evacuation lines in the fuel and hydraulic fluid systems, and methods to reduce or prevent the spraying of pressurized fluids onto hot engine surfaces would greatly improve the chances of successfully suppressing large mining equipment fires. In addition, the use of systems for preventing the ignition of flammable vapors inside the cab, and detecting and suppressing fires originat­ing in the cab, would greatly enhance operator safety. The National Institute for Occupation Safety and Health (NIOSH) recently conducted experiments on meth­ods to reduce the fire hazards associated with large mining equipment. These experiments evaluated the use of cab inerting systems to prevent the ignition of flammable vapors inside the cab and sup­press fires originating in the cab, while maintaining a breathable atmosphere for the operator to bring the equipment to a stop and safely exit the cab.

Jan 1, 2008

By Warren D. Longwill

[ ]

Jan 1, 1981

By J. J. Shields

With the increased use of mechanized equipment in mining bituminous coal, production panels are mined out rapidly. To keep current with the rapid completion of production panels, development work must be speeded up also. Although the same type of equipment usually is employed in development as in production places in the same mine, past output per man for development usually was less than from production panels. A study of development practices in 14 mines reveals a tendency toward equalization of the output per man between development and production.

Jan 1, 1957

By H. P. Greenwald

[For sarno years past the Safety in Minbr. Resaarch J30ard of Great Bri tr-dn ha:1 been making ar.. intensive Gearch for, traterials that \.'ould be 1!\ore ef-ficient than rock dust and th t 'could l1eplace it Jholly or in El:}rt as a muans of prevEll'ltine the propa 'tion' of 'c63.1~dust exnlosions in. mines21 In the course of this \o.'ork several rock c.ur--ts md numerous inorganic compounds I,/ere tested. The result w place incombus.ti ble substFlnces in two main groups~ (1) r.:ho se who sa effect' in suppre aeina Jlihe cor.lbustion of coal dUDt i 0 pro-]

Jan 1, 1940

By G. E. McElroy

[The ventilation of development faces in mines for diluting gas or dust concentrations aid in hot mines for providing air-motion cooling affect, by fan-pipe units discharging high-velocity streams of air close to the face, is an important phase of mitre ventilation. The effectiveness of such units depends largely on the air-flow distribution between-the pipe discharge said the face, a subject on which little definite information is available. A study of the air, flow from grills into rooms3/ has provided sore basic data, but under conditions so different from mine fan-pipe installations in development ends that tae data to are of doubtful application to mine installa¬tions, owing to differences in air-flow conditions. The purposes of this report is to present and discuss the results of an initial series of tests of a general investigation designed to yield definite laws and design data for the discharge of fan-pine lines in nines. The s series was planned to yield preliminary data on the effects of velocity of discharge, size and shape of tripe, and adjacent calls on the air-flow distribution. Tents were made on 10-inch pine with seven different end conditions and one change of wall condition. Changes in size and shape of discharge wore made b y short transformation pieces directly at the discharge end, with the result that effects due to contraction and expansion of the flow, which proved to be of much greater importance than was expected, totally obscured any normal effects cue to size anti shape. The results of this series of tests, therefore, relate to 10-inch pipe with various discharge designs is and ago se reported.]

Jan 1, 1940

By W. J. Kroll

This report on the bibliography of zirconium has been confined to those publications and patents that appear to be useful in the commercial development of the metal, both the malleable and the nonmalleable. The methods of production have been stressed and special attention has been given to the alloys. Compounds of importance, like the oxide and chloride, for the manufacture of the metal or of the alloys have been considered. The use of the oxide in refractories anal in the glass and porcelain industries has been omitted. The present survey is critical; that is to say, an attempt has been made to evaluate the effectiveness of suggestions made in the literature. The exhaustive work of Marden and Richy, Bureau of Mines Bulletin 186, published in 1921, has been taken as a base to start from with the intention of bringing the subject up to date with material published in the last 24 years. During this time there was considerable 'advance in the preparation of the metal and Its alloys, and in the development of new uses. On the other hand, there was little progress in the methods of decomposing the ores, so that the chapter on this latter phase is necessarily short.

Jan 1, 1946

By L. D. Johnson

On a project which is to develop a system to suppress coal dust explosions, a facility has been built and several devices tested. The facility is a 317-foot, 4.5-foot diameter shock tube and to date 53 tests have been carried out with methane-air and methane/coal dust-air as the explosive mixtures. Suppression of slowly propagating (up to 300 ft/sec) flame fronts has been successfully carried out on two tests using the dry chemical extinguishing agent Purple K. Delivery of the material directly into the flame front Seems to be required if effective suppression is to be accomplished.

Jan 1, 1972

By W. T. Benson

The nickel-bearing laterite deposits in the Pine Flat and Diamond Flat areas, Del Norte County, Calif., were investigated by the Bureau of Mines to determine the extent and nickel content of the two deposits and the amenability of the ores to metallurgical treatment. The work was based on drill-hole sampling and metallurgical tests in which attrition scrubbing and sizing, reduction roasting, and magnetic separation were used. Results of the sampling indicated that the deposits are comparatively small and are marginal or submarginal in grade. Metallurgical tests showed that no separation of cobalt from nickel and iron was made by sizing; however, a large portion of the chromium was separated. Reduction roasting and magnetic separation did result in upgrading the iron, nickel, and cobalt, and the simultaneous rejection of chromium.

Jan 1, 1963