Search Documents

By Juh W. Chen

A process for recovery of energy from waste coal fines was investigated. The process, which was developed through laboratory, bench, and pilot plant scale experiments, consists of mechanical cleaning followed by high temperature oil agglomeration and pelletization. The process can produce a quality product under an economically and environmentally acceptable condition. Waste coal fines with ash less than 35: and HHV greater than 6,000 BTU/1b have been upgraded to a product with less than 15% ash and HHV Greater than 11,500 BTU/lb. A computer model has been developed to optimize the processing costs and to perform economic evaluation of specific sites. Ultimately tine model can be utilized to establish a priority listing for a region in assisting the determination of reclamation strategy.

Jan 1, 1983

By Don Steffa

Drift mining, according to California mining terminology - and it is distinctly a California development - is the blocking out and extraction (breasting) of the auriferous gravels of an ancient buried stream either through tunnels, inclines, or shafts; it is one of the minor divisions of the larger classification known as placer mining. The contribution of each of these divisions and of lode mining to the gross production of gold in California totals as follows:3 [ ] The total amount of gold recovered from the placers of California from 1848, when Marshall discovered the precious metal in the mill race at Coloma, to 1928, was $1,226,515,404. The same period saw a total gold production from all operations of $1,823,562,360.

Jan 1, 1932

By Terry G. Montgomery, Eric S. Weiss, John E. Going, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine (LLEM), and after laboratory explosions in the PRL 20-L chamber and the Fike I m3 chamber. The dusts studied included both high- and low-volatile bituminous coals. Low temperature ashing for 24 h at 515 °C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as, or higher than the initial incombustible content. The MSHA alcohol coking test was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared with the initial dust loadings to determine the transport distance of dust during an explosion. All these data will be useful in future forensic investigations of accidental dust explosions in coal mines, or elsewhere.

By William H. Schiffbauer, Timothy Lutz, Michael R. Yenchek

The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL) participated in an experiment to facilitate the remote control of dozers used on coal stockpiles. The experiment consisted of supplementing the normal sensory cues an operator requires to manipulate the dozer from a remote location. NIOSH provided and tested a vision systems intended to give the operator the ability to operate the dozer safely and efficiently from a remote position. This paper highlights the genesis of the experiment, identifies the contributions of Consol Energy and Caterpillar, and details the NIOSH efforts and successful test results. Keywords-remote-control; vision system; stockpiles; safety

A computer system for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. The system operates, interactively from a Tektronix 4014 graphics terminal which handles all input/output functions. The software is installed on a Cyber 74 computer that communicates with the terminal via telephone line.

Jan 1, 1978

By Lawrence K. Requa

The property being worked by the Lewiston dredge of Placer Development (Ltd.) is on the Trinity River in Trinity County, Calif., about 9 miles north of the town of Lewiston (see fig. 1). The nearest rail point is at Rending, Calif., which is exactly 50 miles bar road from the dredge camp. Recently a very good section of State highway has been constructed from Redding to Weaverville, and it is now possible to use this highway for 35 miles of the distance between the dredging property and Redding. The remaining 15 miles, however, are over ordinary dirt road. No trouble is experienced in reaching the property except for a few weeks during the middle of the winter when snowstorms may make travel difficult but not impossible. At present the property consists of about 500 acres of patented land, which extends for about 3 miles along the main Trinity River and Stuart's Pork. It is being worked with one 7-cubic foot, Bucyrus-type dredge, which has an average monthly capacity of about 100,000 cubic yards. To the end of 1931 approximately 10,000,000 cubic yards of gravel had been dredged.

Jan 1, 1932

By S. H. Ash

[On December 2, 1932, the Governor of California called upon the representatives of the mining industry of the State to attend a meeting at Sacramento to discuss ways and means of assisting is relieving some of its perplexing and extremely distressing problems, particularly the mounting cost of accidents which faces the industry with an industrial insurance rate for classification of $11.85 per $100 of pay roll, effective January 1, 1033. The significance of this fact is at once apparent when it is realized that the classification rates per $100 of pay roll for mining have steadily increased for some time, as follows: $3.91 in 1924, $5.54 in 1925 and 1926, $8.04 in 1927, $8.53 in 1928, $9.05 in 1929, $9.42 in 1930, $10.54 in 1931, $10.99 in 1952, and $11.85 in 1133. In other words, the cost rates have acre than doubled, wile statistics indicate that the accident rates nave shown an entirely different trend. At the meeting mentioned, one of the management officials sounded an effective keynote when he declared that a spade should be called: a spade. The perplexing problems of any industry can be approached best and remedies applied if that policy is kept to the front. It is appropriate to mention that high accident rates and a decrease in wages in recent years have unquestionably accounted in part for a unit cost rate, on a pay-roll basis; it also is well to explain that the policy years3 1926 to 1930, inclusive, are the years on which the accident-cost experience for 193: is based. That accident rates :lave not undergone the expected beneficial chance in California's experience is apparent in the words of a Bureau of Mines report:4]

Jan 1, 1933

By Aarne Visnapuu

Dissociation and vaporization of gold chlorides and bromides were investigated by a static pressure method and by Knudsen cell mass spectrometer. Two distinct chlorine and three distinct bromine pressure-temperature relation-ships were observed for the respective salts. The chlorine pressures are attributed to the dissociation of Au2Cl6 and Au2C12, and the bromine pressures to the dissociation of Au2Br6, Au2Br4, and AU2Br2, These pressure-temperature relationships were used to calculate dissociation pressure equations, enthalpies, and entropies of dissociation for each salt. Mass analysis of the vapors over AU2Cls between 83° and 152° C confirmed the existence of gaseous AU2C16. Ionization potential of this molecule is 11.0±0.1 ev and enthalpy of vaporization is 28.l±2.0 kcal/mole. Mass analysis of the vapors over the gold bromides detected only Bra in the temperature range 15°-150° C.

Jan 1, 1971

By C. M. St. John

A series of analyses of possible mining excavations associated with the development of copper nickel deposits of the MINNAMAX site in Northeastern Minnesota is presented. Specific areas such as roof and pillar stability and excavution orientations are addressed. The majority of these analyses were conducted using a boundary element method but some cases were also analyzed using the finite element method. Comparable results were obtained using the two methods but the boundary element method required less data preparation time and computer run time. Results of the analyses, as well as indicating the capabilities of geotechnical numerical models, provide some insights into behavior around multiple excavations in jointed rock.

Jan 1, 1979

By Robert M. Doerr

The research objective was to determine the effect of vanadium alloy additions on the oxidation behavior of cobalt-nickel Alloys. Eighteen alloys were reacted with 0 2 at 0.5 arm and 1,351°, 1,389°, and 1,429° K. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with V additions of 0, 0.9, and 2.7 wt pct. Large early deviations from, or changes in, the parabolic rate constant were encountered, but the reaction rate in most cases declined approximately in accordance with the parabolic rate law. Relatively, the vanadium degraded the oxidation resistance most at the highest nickel contents. In some cases, melting of the oxide was inferred from microscopic evidence and X-ray diffraction measurements disclosed the presence of low-melting vanadates.

Jan 1, 1970

By Larman J. Heath

Preliminary results of an explosive fracturing-solvent injection heavy oil recovery experiment conducted by the Bureau of Mines at a shallow oil reservoir near Bartlett, Kans., are given. Three wells 35 to 50 feet apart were drilled to a depth of 360 feet, and an open hole interval from 300 to 350 feet in the Bartlesville Sandstone Formation was explosively fractured with 3,000 pounds of pelletized TNT in each well. Laboratory tests were made on cores obtained from these wells to confirm the suitability of using an aromatic-type solvent. Injection of a 74-percent aromatic solvent was begun into one well and continued intermittently for approximately 2 months. Crude oil production amounted to 29.6 bbl, or 11.7 percent of the total oil con¬tained within the three-well interwell zone.

Jan 1, 1972

By R. G. Lett

Gaseous products resulting from rapid pyrolysis of coal and coal/inhibitor mixture's by a ruby laser and a flash-tube were monitored on-line by time-of-flight mass spectrometry. The distribution of stable gases from the coal is not Greatly influenced by the addition of small quantities of powdered flame inhibitors. Preliminary studies of the reaction of elementary radicals with coal and coal/inhibitor mixtures are described. The different types of experiments are discussed with regard to possible modification and application to studies of flame inhibitor action.

Jan 1, 1973

By E. Chilton

The National Institute for Occupational Safety and Health (NIOSH) has been conducting re-search to determine the influence of mining machine mounted water sprays on airflows and methane concentrations at the face when blowing ventilation systems are used. Tests were conducted in a full-scale ventilation gallery. Airflow speeds and directions were measured at several locations near the face with ultrasonic anemometers. Methane was released from the face and concentrations were measured in the entry at locations above the mining machine using fixed point methanometers. Changes in airflow speed, direction, and methane concentrations were correlated with water spray operations. The test results using different spray arrangements and water pressures showed that operation of the machine-mounted sprayers can improve face ventilation effectiveness by increasing the velocity of airflow moving toward and away from the face. The improved ventilation resulted in reduced methane levels near the face.

By L. C. IlsLey

Permissible blasting units are approved with the understanding that if actively marketed they will be listed as permissible so that all interested in such safety equipment may know what is available. The last detailed lint of permissible units was published as Technical Paper 4294/. All of the blasting units of that list have become obsolete or have boon modified as covered by extensions of the original approvals.

Jan 1, 1941

By W. D. Haselton

This paper dealing with the mining methods used in producing iron ore from an underground operation located in the central-western part of the Mesabi Range in Minnesota is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts in the United States. The mine here discussed was laid out in accordance with a plan adapted to a rather unusual type of ore body, the nature of which is such that the mining method necessarily differs in certain respects from the method used at most of the mines in this district. A description of it may therefore be of interest.

Jan 1, 1930

By Robert W. Waytulonis

The Federal Bureau of Mines contacted 29 organizations--mine maintenance departments and equipment manufacturers--concerning service experience and construction of diesel exhaust-gas water scrubbers. Scrubbers are used primarily on mobile diesel-powered mining equipment subject to 30 CFR 36. Because the scrubbers cool exhaust gas and act as flame arresters, their failure would compromise safety in underground mines. Scrubber maintenance problems and frequency and modes of failure were identified, and construction materials and techniques were evaluated. Three failed scrubbers were randomly selected from two cooperating mines, and their modes of failure were determined. In conjunction with failure analyses, mine water and scrubber water solution samples were chemically analyzed to characterize corrosive properties. Sludge and mineral deposits and different types of corrosion and metal fatigue were identified as problems leading to scrubber failure. The corrosion process is explained; maintenance practices, construction materials, and manufacturing methods that could be used to reduce premature failures and allow longer effective scrubber life are identified; and basic changes in scrubber design are suggested. If type 304 stainless steel is used throughout the scrubber and regular maintenance is performed, long, dependable service can be expected. Other materials such as 304L, 316, or other more exotic steel alloys may be necessary under certain conditions.

Jan 1, 1982

By Mark P. Zaitsoff

The project involved design, construction, and testing of hydraulic models of culverts, decant and open channel spillways which are typical drainage structures used for protecting mine waste embankments. MSHA (The Mine Safety and Health Administration, U. S. Department of Labor) made a motion picture of the tests. Tests results and products in the forms of graphs, tables and films, demonstrate the principles and factors which govern the function and performance of the three types of drainage structures.

Jan 1, 1981

The selective placement of coal stripmine overburden is examined. Physical and chemical properties of spoil detrimental to revegetation and groundwater are detailed. The United States is divided into regions or similar problems. Five mining methods already used in the industry, that are capable of selectively handling waste are examined in detail. Technical and economic comparisons are made for the systems when applied to realistic mine settings. The same analysis is conducted for five novel methods capable of selectively handling waste. Comparisons are made between novel and existing methods. Suggestions for new and modified equipment are outlined. Recommendations for further research are provided. This volume contains all Appendices to the report.

Jan 1, 1981

By F. P. Haver

The Bureau of Mines has investigated the electrochemical reduction of lead chloride as a method for producing lead without the pollution problems associated with smelting. It was determined that high-purity metal (>99.9 pct Pb) could be obtained, using PbC12 prepared by ferric chloride leaching of galena concentrate: PbS + 2FeCl3?PbCl2 + 2FeC12 + S°. Optimum results in small-scale electrolytic tests were achieved with a bath consisting of 40 to 70 wt-pct PbCl2 dissolved in KC1-LiCl eutectic, an operating temperature of 450° C, a current density of 2.5 amp/in2, and an electrode spacing of 0.5 inch. In large-scale tests made to develop a cell design for commercial application, the optimum electrode arrangement proved to be a bipolar configuration with horizontal plates. This gave a current efficiency of 86 pct with an energy requirement of 0.52 kwhr/lb lead. To determine the effect of impurity buildup in the bath, 1,200 lb of PbC12 prepared by ferric chloride leaching of galena concentrate was electrolyzed over a period of 2 months. Little deterioration of the metal quality occurred in that time; all of the lead produced had a purity equal to or better than corroding grade (>99.94 pct Pb).

Jan 1, 1976

By William C. Cooley

[ ]

Jan 1, 1975