Search Documents

By V. B. Dale

This report is one of a series covering the mineral resources of the Nation. It briefly describes most of the known tungsten deposits in Gila, Yavapai, and Mohave Counties, Ariz. Many of the descriptions are taken from the reports of previous examinations by Bureau of Mines engineers, and from Defense Minerals Exploration Administration files. Where a previous examination had been made, and an inquiry disclosed that little or no work had been done since that time, pertinent information from the report was used in this paper with acknowledgment of the source. However, the majority of the descriptions is from field examinations by the author. In the past 3 years (July 1956-May 1959) only necessary annual assessment work was conducted on nearly all the properties described in this paper. There was no active mining on any of the properties examined.

Jan 1, 1961

By Thornton L. Neathery

Geologic investigation of a mineralized zone in eastern Alabama indicates that large quantities of talc and soapstone are scattered over a wide area close to the surface. Laboratory experiments show that this material may be upgraded to a high-quality talc. A market survey indicates that the talc deposits may be of current and long-range interest. The anthophyllite asbestos which is associated with the talc does not appear to occur in sufficient quantities to be considered as a primary commercial source.

Jan 1, 1967

By K-H. Frohne

This report presents a study of the Cooper sand of the Fork Run pool of Warren and McKean Counties, Pa., and a prediction of the secondary oil recovery by gasflooding the reservoir. A computer program employing a modification of the Craig, Geffen, and Morse secondary recovery calculation was used to make the gas flood performance forecast and is presented in the appendix. The Cooper sand reservoir in the Fork Run pool lies at a depth of about 1,900 feet and covers an area 1/2 mile wide by 2-1/4 miles long. Original oil in place is estimated to have been 8,266,000 STB. The primary recovery mechanism is solution gas drive, and ultimate primary recovery may reach 20 percent over a well life of 90 years. Two computer predictions were made for gas flooding the Cooper reservoir. The first was for a 25-acre pilot five-spot utilizing existing wells, but project economics were poor since only 25 percent of injection gas is utilized for pilot oil recovery. Recovery was 71,000 STB, or 22 percent of oil in place at flood initiation, but required 25,700 scf gas injected per STB of oil recovered. In the second prediction, pilot area performance was projected for the entire Fork Run pool, and economics became good. Recovery was 1,753,000 STB from 25 five-spots after the injection of only 6,400 scf per STB of oil recovered.

Jan 1, 1969

By V. A. Marple

At the Twin Cities "lining Research Center (TCMRC) a project is underway to determine how varying the parameters of a coal-cutting process would affect the amount and the size distribution of the generated dust. The cutting parameters being investigated are the cutting speed, depth of cut and shape of the cutting, tool. To accomplish this research ft is necessary to collect and transport the coal dust venerated at the cutting tool to measuring instruments for analysis. The purpose of this contract was to develop and deliver a system of instruments for measuring the size distributions of the generated coal dust. The instruments employed are essentially those developed for particulate air pollution measurements (1, 2). The instrument system covers a particle size range of 0.005 to 20 microns and is capable of performing in situ measurement and presenting data in real time.

Jan 1, 1974

By David Allen Jones

A depleted county gravel pit was rehabilitated by contracting an artist to convert it into sculpture, rather than using traditional reclamation methods. The sculptor's ideas were generally implemented as designed, but problems arose because of a faulty survey and severe weather. Public reaction was critical. A design symposium was presented by retaining six artists to prepare designs for varied sites. A public forum was offered and video-documented for broadcast. A new art-reclamation project grew out of this project.

Jan 1, 1981

By R. Karl Zipf, Suresh Bhatt

Highwall mining is an important coal mining method. It appears that upwards of 60 highwall miners are presently in operation, and they may account for approximately 4% of total U.S. coal production. A review of the Mines Safety and Health Administration (MSHA) data over the 20 year period from 1983 to 2002 identified 9 fatalities attributable to auger and highwall mining of which inadequate ground control accounted for 1/3. In the past 5 years, 1 fatality occurred in highwall mining. Estimates of the manpower requirements in highwall mining suggest that its fatality rate is essentially the same as for surface coal mining, thus highwall mining appears to be a very safe modern mining method. Highwall stability is the major ground control related safety concern, and operators are required to develop and follow an appropriate highwall mining ground control plan. The plans usually specify the following geotechnical parameters: hole width, maximum hole depth, maximum overburden depth, seam thickness, web pillar width, barrier pillar width and number of holes between barriers. Calculated web pillar stability factor exceeded 1.3 for most designs evaluated. This study examined records from 5,289 highwall miner holes with a total completed footage of about 2,560,000 feet to understand the reasons for early pull out. Average lost footage is typically about 20% of planned footage. Only 35% of the holes reached planned depth, and 20% were short due to rockfalls. Water and adverse geology accounted for 15% of the losses. Mechanical/electrical problems, guidance, and slope stability problems accounted for the remaining 30%. Web pillar stability factor for these holes also exceeded 1.3 in 95% of cases. Best practices to avoid trapped miners include: avoid mining in stream valleys, avoid mining near outside corners, careful alignment of each hole and the use of an onboard guidance system. Several issues in highwall mining ground control require further investigation including highwall mining through old auger workings, highwall mining near old underground mines, multiple-seam and multiple lift highwall mining and finally the size and frequency of barrier pillars.

By S. B. Robertson, D. R. Dolinar, G. E. Hinshaw, G. M. Molinda, D. M. Pappas

Rock falls in coal mines cause many injuries each year. Most of these injuries are not caused by major roof collapses, but from falls of smaller rocks from the immediate top or roof skin. Even though safety professionals and mine operators strive to reduce these types of injuries, there has not been a substantial decrease in the rock fall injury rate over the past decade. Various surface controls are used in mines to control the roof skin. One control that has proven to be very effective is roof screening. Roof screen effectively controls roof skin and provides a high roof surface coverage. Although many mines are reluctant to use screen for primary skin control because of the additional costs of time and materials, others are having great success at controlling both the costs and surface rock. In this study, injury data are presented that show a dramatic reduction in roof skin injuries when screening is used. Much of this success is due to the protection from falling rock that the operators receive from roof screen. Five case studies in which roof screen was used are presented along with the associated costs of materials, impact on bolting advance rates, and potential ergonomic risks. The effects of roof screening on skin control and safety are also included. Finally, this paper provides information about best practices and features of roof bolting machines that affect production and safety.

By J. J. Demeter

Experiments were conducted in 2- and 4-inch-diameter standpipes to evaluate the effectiveness of standpipes as pressure seals. During the experiments, these standpipes conveyed Alan-Wood magnetite (60 to 230 U.S. standard sieve mesh) by gravity flow from one vessel to another of relatively higher pressure. The information obtained has been helpful in a Federal Bureau of Mines investigation of how to make either synthesis gas or hydrogen by a modified steam-iron process employing a continuous recycling stream of granular iron-iron oxide at temperatures of 600° to 900° C. In this process the mixture of granular material flows by gravity from a reduction vessel at low pressures to an oxidation vessel at higher pressures. Data from the 2- and 4-inch-diameter standpipes indicate that it would be practical to use a standpipe as a pressure seal between the reductor and oxidizer. Investigators found that, by gravity flow, the standpipe could convey the Alan-Wood magnetite against pressure gradients up to 1.07 pounds per square inch per foot of column height.

Jan 1, 1961

By August J. Kwitowski

This report presents the results of a joint Bureau of Mines-U.S. Department of Energy project that evaluated a newly developed low-coal mining system: the 4M miniminer system. The evaluation took place from April through October 1981 and determined potential health, safety, and productivity factors for the mining system using the surface test facilities at Bruceton, PA. The planning, testing, results of testing, and a summary evaluation of the 4M miniminer system are included in the report. The miniminer system was found to be a very good concept with future potential for safe, healthful, and economic production in thin-seam mining. The mining system was also judged to have considerable potential for use in some coal seams that are presently considered unminable by other existing mining equipment. The preproduction, prototype version of the miniminer system that was tested suffered from several safety and production problems. These problems are also described, along with suggested remedies.

Jan 1, 1989

By Roger E. Burleigh

In June, 1989, the U.S. Bureau of Mines, undertook a 9-day evaluation of the tin resource potential of the Sleitat Mountain tin deposit. Significant tin-tungsten mineralization is associated with quartz-topaz-white mica-tourmaline greisen alteration of a multi-unit, 57 Ma, peraluminous, granite stock which intrudes Cretaceous Kuskokwim Group flysch deposits. The granite comprises marginal biotite-, intermediate biotite-muscovite-, and central zinnwaldite-granite units, interpreted as a zoned alteration system. Major vein mineralization is confined to two east-west-trending zones of steeply oriented tabular lenses of greisen interleaved with mildly altered granite. Cassiterite is the dominant ore mineral while arsenopyrite, loellingite, wolframite, pyrite, sphalerite, chalcopyrite, and bismuth-oxides are present in minor to trace amounts. The north and south greisen zones are estimated to contain an inferred resource of 128 to 212 million lbs Sn in 28.6 million st of mineralized rock. An 1,800-lb representative bulk sample contained 0.37% Sn, 0.04% W and 17 ppm Ag and is considered an average grade estimate for the deposit. Drill testing by Cominco Alaska Exploration indicates that substantial widths of high-grade tin mineralization are included within the lower grade disseminated mineralization. Depth of deposit erosion is substantial and there exists a high probability for placer tin deposits.

Jan 1, 1991

By Stephen H. E. Phillips

This report outlines the modifications that have been carried out to the original prototype rectangular shaft sinking equipment for its use in a circular shaft. The surface testing of the machine is described where seven, 24 ft. diameter shafts were excavated to an average depth of 21 ft. at rates ranging between 1 ft/hr and 1.9 ft/hr depending upon the prevailing conditions. The durability and productivity standards for the equipment were established indicating that the objectives of the project had been realized. That is, when using the machine the sinking rates could be increased by 25% and costs reduced by a corresponding amount compared with conventional drill and blast methods. In addition it was shown that the machine had been developed to a state of fitness for sustained underground use.

Jan 1, 1981

By A. C. Fieldner

"INTRODUCTION In a previous report3 prepared for the American Gas Association, the influence of washing coal on coke properties and on gas and by-product yields was discussed on the basis of answers to questionnaires sent to coke-oven superintendents and a review of the literature on the subject. This review indicated that the elimination of free impurities by cleaning coal improved coke quality by (a) reducing ash and sulphur, (b) decreasing clinker trouble in burning the coke, (c) diminishing cross fractures in the coke, resulting in greater resistance to breakage on handling, and less small coke and breeze, and (d) greater uniformity in chemical composition and physical properties of coke. Washing also reduced the sulphur in coke and gas and increased the yield of gas and by-products per ton of dry coal charged.This paper is supplementary to the previous report and presents some experimental data obtained with Pittsburgh bed coal from Pennsylvania and Mary Lee bed coal from Alabama.ACKNOWLEDGMENTSGrateful acknowledgment is made to F. J. Pfluke, of the Rochester Gas and Electric Cc., of Rochester, N. Y., for the plant test data on screened lump and washed coal; and to Ray W. Arms, Manager of the Coal Cleaning Department, of Roberts & Schaefer Co., of Chicago, for the data on effect of air cleaning."

May 1, 1931

By Charles L. Harness, A. T. Coons

Sodium carbonate, Na2CO3, more commonly known as soda ash, is the most important of the alkalies. Sulfuric acid is the only heavy chemical, Soda ash enters the market either as the natural product or as a manufactured derivative of common salt. Notwithstanding their common occurrence in closed basins of the Western States, natural sodas are produced at present by only four firms, all in the same California area, and satisfy only 4 percent of domestic demand for soda ash; soda ash made from salt supplies 96 percent of the requirements. The impossibility in wartime of routing all westbound American shipping through the Panama Cami.l has curtailed Pacific Coast receipts of soda ash and-increased the importance of local resources of natural carbonates. One of the most promising of ·these is the recently discovered trona (sodium sesquicarbonate)· deposit 2o·mnes· west of Green River, Wyo. Reserves are likely to run into hundreds ·of million·s of tons, and the deposit probably could be worked by the room-and~pillar· system of mining, like common salt or coal. • • Raw materials ·ne·cessary for manufacturing synthetic soda ash occur closely associated in m·afiy parts· bf the United 8tates. Almost unlimited resources of salt in brines and in rock-salt depbsits are located near limestone quarries in many areas. The· limesto'ne furnishes the carbon dioxide for the manufacture of soda ash arid the lime f o'r the recovery of ammonia. used in one step of the process. Expansion of the industry to meet wartime needs depends chiefly on availability of trained labor, materials, and equipment necessary for the erection of additional units.

Jun 1, 1942

By Doris M. Hyde

Mineral output and trade in the Central American countries were directly or indirectly affected by the sometimes violent civil unrest and recessionary economic developments that have pervaded the region for several years. Central American countries found their foreign exchange export earnings and traditional market areas shrinking while essential import costs were rising. Restricted spending measures were adopted by governments and private industries. Domestic investment funds for mineral development and exploration projects were among the first casualties of these austere budgetary measures, especially since weak demand and depressed mineral prices diminished the probability of a favorable cost-benefit ratio. The lack of physical security and political stability also discouraged private foreign investment. The United States Congress enacted the Caribbean Basin Economic Recovery Act of 1983 (19 U.S.C. 2702), more popularly known as the Caribbean Basin Initiative (CBI). This legislation was designed to stimulate economic recovery and promote economic development by increasing private investment and trade in the Caribbean Basin countries. The act provided for the elimination of U.S. duties on most trade items imported directly from eligible Caribbean countries, provided at least 35% of the product value originated in the region. The financial assistance components of the CBI were to be supportive of the basin's private sector as well as assist general economic stabilization programs.

Jan 1, 1985

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Common-wealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. Except for the mineral fuel commodities, the detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. In October 1977, responsibility for the collection of data on mineral fuels-coal, petroleum, natural gas, and natural gas liquids-was transferred to the newly created Department of Energy. Although chapters covering these commodities will no longer appear in Volume I of the Minerals Yearbook, quantity and value data have been included in most of these summary tables to maintain statistical consistency in State and national value of overall crude mineral output. This shift in responsibility has also resulted in changes to the composition of the "Nonmetals" and "Mineral Fuels" groups in table 1 and table 2. The commodities-asphalt and related bitumens (natural), carbon dioxide (natural), helium, and peat-have been removed from the "Mineral Fuels" group, and are now included under the "Nonmetals" group. There has been no change in the components of the "Metals" group.

Jan 1, 1980

By Arcy R., D&apos George

A process for removing sulfate from Great Salt Lake brines and other natural brines, including sea water, has been developed. Sulfate is quantitatively removed by precipitation as barium sulfate in a cyclic process employing ion-exchange techniques. Barium is continously recovered and recycled, and sodium carbonate and sulfur or sulfuric acid are produced as byproducts in quantities sufficient to more than defray the cost of desulfation.

Jan 1, 1967

This section presents highlights of world economic and mineral industry performance in 1982, a year characterized by continued recession, and selected 1983 forecasts of economic indicators of importance to the mineral industry, some of which indicate a modest improvement in the economies of the United States and Western Europe. The U.S. Economy in 1982 In 1982 U.S. gross national product (GNP) in current dollars increased at a rate of 4 percent, but GNP adjusted for inflation (real GNP) declined at a rate of 1.8 percent. Yearend 1982 real GNP was at roughly the same level as in 1980 (table 1). Thus no growth in real terms had taken place in the United States during the 1980-82 period.

Jan 1, 1983

By T. C. Green

A two-phase program evaluated commercial proximity warning devices and then served to design and develop an automatic electrostatic field strength measurement device with improved performance. The Phase I program consisted of test and evaluation of three commercial proximity warning devices, all of which operate on the principle of electrostatic field intensity measurement for determining proximity to high voltage power lines. Performance testing of these devices utilized full-scale cranes and power line systems and a scale model facility. The evaluation results were reported in the Phase I report entitled "Evaluation of Proximity Warning Devices" dated 22 February 1980. Under the Phase II program, a microproressor-based data acquisition system was designed and developed to collect and measure field strength at distributed points around the crane boom. This unit (referred to as the Distributed Sensor AC Electrometer) measures the field strength about a crane boom using 17 distributed sensors. Keyboard control is provided for the equipment operator. Measured field strength values are displayed on a line printer and recorded on magnetic tape. Laboratory testing of this unit demonstrated performance characteristics and field strength measurement accuracy within the design goals. A Phase III measurements program is proposed using the AC Electrometer to map the field strength contours about power line configurations.

Jan 1, 1981

By M. Shamsuddin

Information on total estimated uranium reserves and domestic requirements have been collected, A survey has been made on the possibilities of recovery of uranium from low grade and complex ore deposits, e.g., marine phosphorites, shales, coal, sea water, etc. In order to assess the potential for uranium recovery from uraniferous phosphorites, available thermodynamic data of uranium minerals, compounds and aqueous species have been collected. The existence of uranium complexes with chloride, fluoride, carbonate, phosphate, sulfate, etc., in ground waters have been evaluated at different pH's. There seems a great need to study the relative stability of these complexes in order to judge the applicability of solution mining technology for selective leaching of uranium from phosphorites. A typical flow-sheet demonstrating recovery of uranium from wet-process phosphoric acid has been included in this report. Some essential features of the economics of uranium recovery from uraniferous phosphorites have been briefly considered and recommendation have been made for further studies.

Jan 1, 1980

By L. A. Morely

The overall objective of the subject contract was to investigate the application, economic, and safety considerations of electrical-shock prevention techniques applied to surface and underground mines. Volume I of the four-volume final report starts by summarizing all research performed, and synopses of the three other report volumes are included. The balance of this volume concerns one major task of the contract, the protection of maintenance personnel. After specifying the scope of work for the task, electrical is defined, and needed ground-fault relay characteristics to prevent ventricular fibrillation are established. This is followed by an analysis of alternating-current systems, a comparison of these systems with respect to body currents, and the advantages and disadvantages of the various ground-fault protection techniques. An analysis of direct-current systems for off-track vehicles is then covered. These analyses form the basis for the research recommendations which along with suggestions for future research, conclude the report volume.

Jan 1, 1982