Search Documents

By David Flores, Benjamin Cebrian

This paper describes extensive engineering approaches to achieve both dilution control while not hurting fragmentation in the very hard, massive ore sections of a mine case study. Ore Tracker microchips are used to correlate performance of these designs at the SAG mill (bottleneck of this specific operation). Another gold mine uses the same technology to detect when and where operational dilution is happening. The system tells where flagging of the different ore bodies has been followed in order to detect which operators pass the excavation limits beyond ore control flagging.

Feb 1, 2020

By Lewis L. Oriard

The purpose of this paper is to provide an overview of close-in blasting effects on various types of structures and building materials, as encountered in this writer's professional practice. Structures range from old, deteriorated historical monuments to new, heavily reinforced buildings. Materials range from clay adobe to concrete and steel. Site locations range from tropical to arctic. Blasting ranges from sculpture blasting inside buildings to "coyote" blasting and large surface blasting operations. Space limitations permit a brief discussion of only 25-30 specific cases, but they have been selected to be typical of conditions found on hundreds of similar cases. The writer was asked to present a discussion of representative cases where relatively high vibration intensities were experienced. Virtually all of these cases were free of damage, but the few damage cases provide valuable insight to the mechanisms involved. Observations of such damage and non-damage cases have served as the basis of this writer's criteria for various structures and materials, as well as the technology to conduct blasting operations within those criteria. A sampling of these experiences is gladly shared with the reader.

Jan 1, 1991

By Lon Santis, David Buckwalter, Ken Steinmetz

This paper describes a magazine security system using two readily available cellular telephone-based technologies. The system is comprised of vibration sensors and remote cameras. The system is used at a Bureau of Alcohol, Tobacco, Firearms, and Explosives (ATF) licensed explosives storage location in Pennsylvania to comply with PA Department of Environmental Protection (PADEP) regulations. The system provides instant notification to the licensee via cellular modems, text messaging, phone call, and e-mail. Likewise, the licensee can control the system remotely over the internet and using text messaging commands. The vibration sensors attach to the door of the metal type I magazines magnetically and detect any movement or vibration. The cameras trigger on movement and thermal radiation changes and can also be triggered manually to check alarms received from the vibration sensors. The previous system was comprised of a base unit and magnetic strips. The magnetic strips were powered by a hard line from the control unit and mounted on the doors and top of magazine creating a bond, that when broken triggered an alarm. Our main issues with the unit were the delay in alert times and tech support. Because of these issues, we decided an upgrade was necessary. Compared to that previous system used at this site, these new systems are highly affordable, carefree and reliable.

Jan 1, 2014

By Daniel B. Conn, John L. Floyd

PhotoSeis™ is a blast analysis method that combines the advanced technologies of high speed motion picture photography and digital seismology. When fracturing rock with the use of explosive energy, the human eye cannot detect the details of the process due to its short duration. An extended time base is required to accurately quantify the response of the rock mass to the detonation process. This time base is provided by the use of high speed motion picture cameras. The control of ground vibrations and airblast is an important consideration when developing efficient blast designs. High vibration and airblast levels can be an indication of improper design, inaccurate detonators, or adverse geology. Since many factors can elevate airblast and ground vibration, a greater understanding of the site specific response to the blast design is needed that is beyond the scope of simple seismographic recordings. By synchronizing the photographic record provided by the high speed motion picture cameras with the airblast and vibration information from digital seismological monitoring, the Photoseis™ technique can be of great assistance in controlling airblast and vibration and optimizing the use of explosive energy for rock fragmentation.

Jan 1, 1990

By Richard H. Granhom

Detonation pressure, or Chapman-Jouguet pressure, is an intrinsic property of an explosive, and like detonation velocity, is an indicator of explosive performance. Pressure and velocity are also important for calibrating computer codes and for other calculations such as the stress imparted to rock or metal by an explosive. The detonation pressures, P~cj, of many "ideal" explosives have been measured indirectly by recording some hydrodynamic flow variable other than pressure, with P~cj being inferred from hydrodynamics and the assumed Chapman-Jouguet equations. One such method is the difficult and expensive "aquarium technique''.] Commercial explosive manufacturers generally rely on estimates of P~cj generated by computer codes not explicitly designed for non-ideal explosives typically used in commercial applications. Over the last decade, U.S. national and government laboratories have developed in-situ gauge techniques such as the manganin gauge, for direct measurement of detonation pressure. Manganin is an alloy of copper, manganese and nickel, and is ideally suited for use as a pressure transducer because its electrical resistance changes with pressure, but is nearly constant with changes in temperature. A simplified manganin gauge technique adapted for use at a commercial test site is described and some initial results from measurements on commercial emulsion explosives are presented.

Jan 1, 1991

By B Mohanty

Full-face blasting rounds have been used to excavate a 4.6-mdiameter shaft at Atomic Energy of Canada Limited's Underground Research Laboratory near Pinawa, Manitoba. Both standard pyrotechnic delay detonators and the newly developed electronic delay detonators (EDD) were used on the project. The full-face blasting technique, employing 89-mm-diameter relief holes and 38-mm diameter blast holes, NG-based explosives, and the regular long period delay detonators, has been standard practice at the site, giving excellent wall control and fragmentation results. The comparison blasts using pyrotechnic detonators and EDDs were carried out to test the operational logistics, timing accuracy and blast results obtained with the latter. The long period pyrotechnic delays ranged from O to 18, with the nominal delay varying between 350 ms and 800 ms. The EDD blasts used the same number of periods, with the respective delay interval between successive periods set precisely at 190 ms and 210 ms for the two blasts. Based on a broad range of critically assessed parameters, the EDD blast results proved to be signficantly superior to those obtained with regular pyrotechnic detonators. The results have been analyzed in detail and the relative merits of the two delay systems have been determined. Alternative designs to derive maximum benefits from EDDs in shaft and tunnel blasts have also been suggested.

Jan 1, 1990

By S K. Mandal, S Dasgupta

"Damage is classifi ed as loss in the integrity or deterioration in the quality of rock massand is infl uenced by methodology of excavation on the geo-technical properties of rockmass. Overbreak, on the other hand, is the result of damage and is quantifi ed in either of the terms viz., extra mucking, shot-creting, application of extra support system and extension of scheduled completion time. Damage or overbreak in rock mass by the impact of blasting, is generally unavoidable but, the magnitude can be minimized so that it does not deteriorate the quality or integrity of structure. The paper, here, analyses magnitude of overbreak of a powerhouse cavern with respect to different blast patterns implemented at the site. The magnitude of overbreak was analyzed in terms of profi le measurement with the help of laser profi ler and percentage of halfcast markings observed on the periphery rock wall. The paper revealed the impact of decoupling ratio, blast pattern and geometry of blasting patch on the magnitude of overbreak. The authors observed that presence of un-favourable joint pattern or foliation plane along the periphery rock wall couldn’t contain magnitude of overbreak within allowable limit. The analyses revealed that percentage of half-cast markings on periphery rock wall was infl uenced by response of rock towards detonation of explosive and cannot be a single parameter to assess the effectiveness of a blast. The analyses also revealed that magnitude of overbreak for down-stream wall was more than that observed in up-stream wall."

Jan 1, 2008

By Daniel Johansson, Markus Danielsson, Håkan Schunnesson

In sublevel caving, blasted material flows gravitationally into the drawpoint from above in a periodical manner. This type of flow behavior entails muck pile conditions that are variable along the course of extraction. The effect of this variability on the LHD (Load-Haul-Dump) operation in terms of loading efficiency and ability to undermine the blasted ring is not fully understood as of today. This paper presents results from a field test in LKABs Malmberget mine in Sweden, where the influence of fragmentation on the loading operation has been studied in detail. Drawpoint filming was conducted for extraction of two rings equivalent of roughly 10000 metric tons (~9842 long tons) of material each. The analysis includes fragmentation measurements, muck pile classification, and general estimations in terms of loadability. Further, an evaluation of LHD machines from two different manufacturers was conducted to identify and highlight differences. The results show that fragmentation, muck pile compactness, and flow characteristics are all interdependent. Flow disturbances and the subsequent loading of compacted fine material in the back of the ring have been identified as the main reason for occurring problems and prolonged digging times. However, the ability to sufficiently undermine the blasted ring has been identified to primarily depend on digging depth which is only observed to be high during flow disturbances. An absence of flow disturbances seem to promote high loading efficiency but simultaneously limit the maximum digging depth. A mid-range particle size distribution with a low amount of fines has proven beneficial for overall loading efficiency. The various LHDs employed showed significant variations in terms of ability to handle difficult loading situations (e.g. compactness, boulders, etc.).

Jan 1, 2018

By Dennys Huaman, Carlos Rojas

Using the Levenberg-Marquardt algorithm to reparametrize the Kuz-Ram original model equation of the mean characteristic size and assess the errors of both models and their comparisson using different statistics measures like chi-squared or relative error with the usage of the Monte-Carlo algorithm.

Feb 1, 2020

By G. C. Naveen

Punatsangchu Hydroelectric Project Authority is constructing 1020 MW underground hydroelectric project in Bhutan. The project envisages construction of concrete dam, Desilting Chamber, Head Race Tunnel, Power House Complex and Tail Race Tunnel. Tunneling is one of the major activity in any underground projects as they are driven for multiple activities. By and large the tunnels are a major part of connecting networks from surface to caverns/underground working sites. Many tunnels in hydropower project are part of water conducting systems and one such important tunnel is the Tail Race Tunnel in this project and had to be excavated in thinly foliated rockmass conditions by D&B method. The rockmass is traversed by three to four joint sets and few minor shear seams. Rock Class “Q” values were between III and IV. Tunnel was excavated by full face parallel hole drilling blasting method. The adopted blasting method consisted of drilling 45mm (1.77 inch) diameter holes to a depth of 2m and the drilled holes were charged with 40mm (1.57 inch) diameter cartridge explosives and charges were initiated with half second non electric initiators. The perimeter holes were drilled at closer spacing of 30cm (1 feet) and alternate holes were charged using 32mm (1.23 inch) diameter cartridges explosive. Low dipping foliation joints present in the rockmass tend to slab in crown portion and erratic occurrence of intrusive bodies lead to unpredictable behavior of rock mass posing a major challenge for the safe excavation. Stability was a major issue through controlled blasting under constant supervision too could not limit the overbreak in certain weak rockmass conditions thereby exposing cavities of about 2.5m (8.2 feet). The stabilization of these cavities and handling the overbreak due to rockmass condition was time consuming and warranted additional supports. With systematic measurements and controlled blast designs the Horse Shoe Shaped Tail Race Tunnel of 9.1 m (29.85 feet) diameter and 304m (997.37 feet) length to connect with Downstream Surge Gallery of 314m (1030 feet) length, 18m (59 feet) wide and 58.8m (193 feet) height in thinly foliated and jointed biotite gneiss rockmass was successfully excavated.

By Dr. Kyle Perry, Ryan Sibley

Rock blasting is an inherently difficult field to quantify independent & dependent variables and the specifics of how the energy interacts with the material for a number of reasons. Independent variables such as geology are innumerable and stochastic, thus, on a laboratory and full-scale basis these variables are assumed to be homogenous across the desired rock boundary. Dependent variables are difficult to quantify in the laboratory based on the specific aspect of the fracture mechanisms that caused the fracturing. The same variables are difficult to quantify in the field because of the shear amount of material being blasted. The energy interactions with the material are difficult to quantify due to the rate of the reaction and the lack of quantification of independent variables. The second main issue with laboratory scaled rock blasting is the nature of the small form-factor explosives required for use in a scaled setting. These explosives that are utilized, traditionally PETN detonating cord, have a greater ratio of potential energy converted to shock energy rather than gas energy when compared to traditional field explosives, such as emulsion or ANFO. Research over the past decades has indicated that gas pressure has the greatest contribution to rock blasting performance, such as fragmentation and material throw. The factor of varying ratios of energy production has not been discussed in any of the reviewed publications. Publications discuss dimensionless scaling, dynamic similitude, and length-based scaling, however, none of these scaling methods discuss the ratio of energy production. The main focus will be correlation of energy production ratio of shock versus gas to dependent variables. This paper analyzes previous publications within rock blasting and related field as they pertain to scaling procedures and will highlight the similarities and differences in the various publications and detail the observed omitted variables that possibly lead to skewed data.

Jan 21, 2025

By Ashwani Jain, D K. Soni

Compressive strength of rocks is often required by mining engineers and quarrying authorities for blasting operations. Uniaxial compressive strength of rocks can be predicted with reasonable accuracy with the help of point load strength tests which can be easily conducted at site by the field staff, simultaneously as the cores are recovered from drilling operations. A number of diametral point load tests and uniaxial compressive strength tests have been conducted on the specimens of different rock types under air dried, and saturated condition as well to study the effect of ground water saturation on strength. It has been observed that due to saturation uniaxial compressive strength and point load strength get reduced to a maximum of 32 and 29 per cent respectively. It has also been observed that uniaxial strength is sixteen times the point load strength in air dried as well as saturated condition. However, this factor used for calculating uniaxial compressive strength may be reduced to a lower value for the safety of miners in field blasting operations.

Jan 1, 1994

By Valeri Mitkov

Studena Quarry is one of the main suppliers of inert materials for concretes production in Sofia. It is characterized by massif heterogeneity in density and fissuration. Failure to take into consideration this fact during the planning of the blasting works recently had unsatisfying results in their carrying out – obtaining of materials with too small dimensions or high percentage of outsize material. Series of test blasting were carried out to find the relations for calculation of the main parameters of the drilling and blasting works. The blasting network was enlarged to 6 x 6 m, the diameter of the shot-boreholes was changed from 110 to 152 mm, the stem of the boreholes was significantly reduced and the relative consumption of blasting agents as a whole was reduced to 0,37 ?g/m3.

Jan 1, 2010

By David Cheung, S. Paul Singh

"The characteristics of a blasted muck pile can have a significant effect on the productivity and economyof loading and hauling operations. Poorly fragmented and tight muck piles, caused by insufficientdisplacement of the broken rock, lead to higher digging and hauling costs. Therefore muck pile must be tailored to suit the loading and hauling equipment. In order to achieve this objective, it is imperative to understand the relevant muck pile characteristics and factors governing them. In general, muck pile characteristics are governed by the blast design parameters, rock mass geology, explosive characteristics and post-blasting requirements."

Jan 1, 2017

By Krishna Nand

For assessing the safety of structures during underground explosions, ground particle velocity gives the best damage criteria, and 100 mm/see of ground particle velocity has been internationally accepted as the threshold value of safety (no damage). Results of extensive controlled underground explosion experiments conducted by the author to study the effects of ground vibrations on specially prepared concrete blocks, and also on low rise buildings and dams showed that no damage normally occurred when ground particle velocities were less than 100 mm/sec. Analysis of a large number of accelerograms from a dam site in India also indicated that no damage occurred to normal structures when integrated ground particle velocities were less than 100 mm/sec. Major damage in well built structures like a dam was noticed for ground particle velocity as high as about 350 mm/sec. These results are also generally substantiated from damage data obtained for various structures during other earthquakes, including Elcentro (1940), Taft (1952), Parkfield (1965), and San Fernando (1971). These studies, therefore, suggest that the damage criteria during underground explosions and earthquakes are similar; and 100 mm/see of ground particle velocity seems to be the general threshold value of safety (no damage) against ground vibrations.

Jan 1, 1988

By John L. Floyd

The use of explosive energy to displace overburden or waste material can provide substantial savings to operations which normally rely on mechanical means for material removal. To optimize the available explosive energy, it is important to quantify the rock's response to the type of explosive and explosive accessories used. During a blast, rock breakage and movement occur so rapidly that the naked eye cannot detect the details of the fragmentation process. A relatively high speed motion picture camera (500 frames per second) can provide the extended time base needed to analyze in detail the site-specific rock response to the explosive detonation. The data of importance to blast casting that can be quantified from these films includes initial face movement, trajectory of rock, and differential face velocities of the material shot. In addition, the ground swell velocities, stemming confinement, and stemming ejection velocity can be determined. The performance of explosive products and delay element accuracy can also be ascertained. The use of high speed motion picture photography and analysis can reduce the number of field trials necessary to maximize explosive performance and increase the benefit provided by blast casting, and in turn, lower production costs. This paper will discuss the methods used for data accumulation and analysis. In addition, three field studies conducted at three separate mining operations will be presented.

Jan 1, 1988

By Paulo Couceiro

Highly non-ideal explosives usually tend to react expressively below their ideal detonation velocities. In these cases, dimensional effects and product heterogeneities become important to proper model the detonation state. Although Direct Numerical Simulation (DNS) techniques can provide a complete and exact solution for this problem, its actual computation cost is still not practical for industrial applications. In order to minimize these constrains, a simplified two-dimensional steady non-ideal detonation model for cylindrical stick explosives is developed. Based on an ellipsoidal shock shape approach, the proposed model uses the quasi-one dimensional theory for the axial flow solution and combine the post-shock sonic flow criteria with some limiting conditions for the explosives’ unconfined radius determination. Due to its attractive fitting capability for unconfined detonation experimental data, the model offers the possibility to predict the non-ideal detonation state for any diameter, resulting in a full mapping of the diameter-effect curve of the explosive. Thus, the proposed engineering approach is used to model the main properties of some of the most common ammonium nitrate-based explosives used in mining and quarrying industries, including the complete axial flow solution.

By Paulo Couceiro

Highly non-ideal explosives usually tend to react expressively below their ideal detonation velocities. In these cases, dimensional effects and product heterogeneities become important to proper model the detonation state. Although Direct Numerical Simulation (DNS) techniques can provide a complete and exact solution for this problem, its actual computation cost is still not practical for industrial applications. In order to minimize these constrains, a simplified two-dimensional steady non-ideal detonation model for cylindrical stick explosives is developed.

Feb 1, 2020

By Eric Roller, Elliott Giles

All flyrock incidents have the potential to result in injuries or fatalities that can result in loss of company reputation, license to operate with clients, and bear the exposure to high cost liability. From 2007 to 2009,one NA Quarry and Construction Business experienced a series of flyrock incidents. In the spring of 2009, this business declared that the frequency and severity of Flyrock Incidents had reached an unacceptable level. A Flyrock Elimination Program was launched.

Jan 1, 2012

By Thomas M. Keevin, Gregory L. Hempen

A user-friendly model for environmental effects from underwater explosions is presently available. The model by Munday et al. (1986) is effective for determining fish mortality radii from underwater shooting. The IBLAST program (Coastline Environmental Services 1986) from this model includes estimates for both borehole-loaded explosives for demolition or rock removal purposes and midwater shots. Midwater shots may be used for fish population assessments or some seismic surveys. The program produces approximate mortality distances for planning purposes. IBLAST does have serious shortcomings of which users should be aware.

Jan 1, 1995