Search Documents

By L. Chaves

In rock blasting, due to numerous factors, both controllable and uncontrollable, the execution rarely meets the planning. The powder factor is an important KPI for blasting since it represents the amount of explosive used to fragment the rock, therefore it depends on the rock mass characteristics and may be influenced by factors such as weathering and drilling quality. The blasts at the Serra Sul mine, S11D project, are usually big blasts and the high productivity is a challenge for maintaining the quality of the whole drill and blast process. It is important to know the contributions of each of the most common influencing factors of the powder factor to direct the efforts to the improvement of the process. A buildup model is presented to evaluate the contributions of five influencing factors to evaluate the planed x executed powder factor. The factors considered in the model are the average hole depth, the amount of hole/blasted volume, the stemming and decking length, the linear charge weight, and the density of the explosive used. The build-up may be applied for both individual blasts and for overall view of the blasts in a period. A case study is presented with the application of the model for the monthly powder factor analysis at Serra Sul mine has contributed to direct efforts to enhance drilling quality and preservation of the drilled holes.

Jan 1, 2024

By Randall M. Wheeler

Many blasting companies are using simulated production ground vibration waveforms to aid them in the control of their vibration effects. The simulations are typically produced by using a seismograph to record a signature waveform from a single hole shot and subsequently applying the various delays to be used in a proposed production design. The ability of this simulation method to give good results usually depends on three primary factors. These are: 1) the homogeneity of the seismic travel path from hole to hole; 2) the consistency of the seismic energy release per unit of explosive from hole to hole; and 3) whether or not the delays fire as planned.

Jan 1, 1991

This is the story of a blast - not a large blast by todays standards as it only involved a total of approximately 50 cubic yards of rock. Nor did this blast involve any new or revolutionary blasting technique or require involved analysis or the applications of rock mechanics theories. Instead, it was a blast that involved the tried-and-true principles of good blasting: precise alignment of blastholes; selection of explosives and detonators designed for the conditions encountered; extreme care in loading and hooking up and the use of several ingenious devices and techniques to achieve the proper loading and firing of the blast

Jan 1, 1976

By Kirk Yeager

During the last several years the FBI has been involved with a detailed study of explosives designed to replicate formulations utilized world-wide by terrorists. In addition, numerous formulations , based on literature and internet sources were examined. During the early stages of this work, a good many of the energetic mixtures studied were based on simple ammonium nitrate fertilizer. While the use of ammonium nitrate in commercial explosives is well studied and documented, the characteristics of the mixtures produced by criminals and terrorists have been less well researched. To aid law-enforcement in understanding the properties of these poorly understood formulations, a “cradle to grave” examination of their characteristics was conducted.

Jan 1, 2001

By Marcia Harris, Richard Mainiero

The New York State Department of Transportation recently commenced highway widening and drainage improvement projects in Clarence and Amherst, NY. Drainage improvements including the installation of storm sewer lines required excavation to a depth of 2.5 m (8.2 ft). In September 2002, NYSDOT stopped further blasting when 800 ppm CO was detected in the basement of a house near the blasting site. At the insistence of NYSDOT, the general contractor developed a new blast plan with the assistance of an environmental consultant. The plan provided for the installation of multi-gas monitors in buildings of special concern and/or with basements and residential type CO monitors in all other buildings within 100m (330 ft) of the blast. The multi-gas monitors would be remotely monitored. The plan provided action levels which would ensure public safety. The blast design was also modified to allow for better venting of CO. Blasts were limited to 20 ft lengths. The overburden was to be removed from the rock and blasting mats put in place to prevent flyrock. Approximately twenty feet of trench adjacent to the blast was left open to allow ground movement and gas release. The use of CO monitors was effective to alert occupants of a building to the presence of CO. The most effective appeared to be the residential type CO alarms with digital readouts. They were simple and easy to use and allowed the public to participate in the process. False alarms were repeatedly received with the more sophisticated instrumentation. Residential type CO monitors are preferable to warn people near blast sites. More sophisticated instrumentation should be avoided unless personnel are experienced in its use. A general overview of the blasting and monitoring is presented and discussed. The use and effectiveness of residential type CO monitors and multi-gas monitors are discussed.

Jan 1, 2004

By Piet Halliday, Ellina Kharatyan

Conventionally, emulsion matrices (unsensitized) need to be sensitized to become detonable explosives. This is done either chemically or mechanically. Both methods have their advantages and disadvantages. Mechanical sensitization involves the addition of microballoons (plastic or glass) to the emulsion matrix, in order to create hot spots during detonation. This is usually done at the manufacturing site and poses a safety risk in terms of the storage, transportation and handling of a 1.1 type explosive. Many countries throughout the world make use of chemical sensitization as opposed to mechanical sensitization as this allows for the storage, handling and transportation of two 5.1 type products rather than the 1.1 type explosive. Chemical sensitization involves the addition of a small amount of a chemical that reacts with a component of the emulsion matrix causing the formation of gas bubbles that act as hot spots during detonation. The disadvantage of this is the lack of accurate density control (due to various factors affecting the reaction) and the lack of comprehensive understanding of the operators of the reaction. This can easily result in poor blast performance. Due to these disadvantages a pumpable, non-detonable (5.1 type) mechanical sensitizer was researched and developed. This product allows for pumping at a 50:50 volume ratio with the emulsion matrix, when loading into blast holes. The significance of this is that a 1.1 type explosive is formed in the blast hole. As such, the security and logistical issues of the transportation and storage of the 1.1 type explosive are eliminated. Another advantage is accurate density control of the final product, specifically in small diameter long hole applications. A cost effective, unique mini pumping system has been developed for the loading of this product. Moreover, this system can easily be used for secondary blasting applications and the on-site packaging of cartridged explosive products.

Jan 1, 2015

By Thomas E. Lobb, Harry C. Verakis

Blasting is a primary means of extracting minerals and ores at surface mining operations. The domestic consumption of explosives and blasting agents during the year 2001 was about 5.25 billion pounds. Flyrock is always a major concern for the blaster. Flyrock from surface blasting operations has caused serious injury and death to employees and other persons. Injuries due to flyrock and the lack of blast area security accounted for over two-thirds of all blasting-related injuries in surface coal, metal, and nonmetal mines during the period 1978-2002. Selected accidents due to flyrock and lack of blast area security in surface mining are presented in this paper. Incidents related to construction blasting are also described. Techniques to mitigate blasting accidents are discussed. These include proper blast design, driller-blaster communication, inspection prior to loading and firing the blast, removing employees from the blast area, controlling access to the blast area, and using a blasting shelter. An experienced driller could detect potential problem areas such as voids, mud seams, incompetent rocks, and other irregularities by observing the progress of drilling. The drill log should include the details of any unusual or exceptional circumstances noticed during drilling. A blaster may need to alter the loading configuration to alleviate potential problems. Basic blast design is sometimes taken for granted and assumed to be proper for the conditions encountered, but one size does not fit all. It is known from the physics of blasting that the explosive energy takes the path of least resistance. The path of least resistance could generate flyrock, depending on the blast site conditions. A combination of ‘borehole tracking’ and ‘laser profiling’ can assist in improving the design of a blast. The blaster can use these tools to adjust borehole loading to match site conditions.

Jan 1, 2004

By Catherine T. Aimone-Martin, Brent Meins

Blast vibration monitoring for buried pipelines is typically conducted at the ground surface with a shallowly buried geophone. In many jurisdictions across the U.S., blast-related vibration limits set for pipelines are dictated by surface measurements and do not consider the significant reduction of PPV amplitudes acting on the pipe at depth. This study involved a vertical array of geophones deployed in drilled holes at two blasting sites of the Loop 202 South Mountain Freeway construction project in Phoenix, Arizona. City of Phoenix pipeline engineers were concerned that blasting would damage an aged 48-inch (122 cm) prestressed concrete cylinder pipe (PCCP) that serviced water for South Phoenix

Jan 1, 2019

By E. Contestabile, B. von Rosen

On August 5th, 1998, a tractor-trailer carrying approximately 18,000 kg of blasting explosives, struck a rock face on the side of the road near the town of Walden, Ontario. Eye-witness accounts of the incident state that there was an intense fire for approximately 30 minutes before the detonation. The detonation caused severe damage to the tractor-trailer, shifted the pavement and caused blast damage to the rock face. A rock fragment was recovered almost 2.5 km from ground zero and a 70 kg piece of an axle assembly was recovered over 1 km from the site. Windows were cracked at distances of almost 3 km.

Jan 1, 2001

By Lewis L. Oriard

Some two million cubic yards of sandstone and orthoquartzite were blasted and excavated at Upper Stillwater Dam, located high in the Uinta Mountains in northern Utah. The material was processed to produce concrete aggregate for the construction of the largest roller compacted concrete (RCC) dam ever constructed, and one of just a few in existence. The dam cross-section is shown in Figure 1. The aggregate was sound rock produced from required dam foundation excavation and from a quarry located about 1/2 mile from the dam site. Representative compressive strengths of the sandstones and quartzites were in the range of 20,000 to 30,000 psi.

Jan 1, 1993

By D. C. Valdemeri, Oppermann J. P. Z., R. G. Schaarschmidt, C. S. Mendonca

This case study was conducted in an aggregate company, located at Estância Velha town, RS, Brazil. The study was based on the results of vibration monitoring mainly in terms of PPV (peak particle velocity) and frequency. Changes in the blasting design were performed to adjust the limits determined by the Brazilian standard NBR 9653:2005. Understanding the seismic wave attenuation for the site, changes in the blasting design were tested to fit the limits, such as reduction of maximum charge per delay, initiation orientation and sequencing and finally the replacement of accessories like "shock tube" by electronic initiation system. The results are shown below.

Jan 1, 2015

By Florian B. Janoski

The annual consumption of electric blasting caps in the United States approaches 100,000,000, so, over the last eleven to twelve years about one billion have been used. The author has made hazard assessment measurements in connection with proposed electric blasting operations in many places: under a giant, operating electrical generating station, under some of the highest voltage power lines in the country, and around many large electrical distribution substations. Electric blasting was safely conducted in all instances. Measurements of stray current, and of pickup under high voltage power lines are easily made, but it was always a more complex chore to make a good radio frequency hazard assessment "close in" to a high power RF transmitting source.

Jan 1, 1977

By R L. Mayville

The author explains why the strategic location and important limestone reserves at Chattanooga Quarry led to a decision to extend operating life by continued benching down to lower levels. He discusses the steps taken to accomplish this objective. These include relocation of the primary crusher from the second level to the fourth level, pre-testing of explosives designs and powder factors, control of a substantial water problem, and computer monitoring of stone production costs.

Jan 1, 1984

By John C. Adams, Darrel D. Porter

After conventional drill and shoot methods were determined to be unfeasible due the fractured nature of the ground, a "coyote" blast was designed to produce 250,000 tons of rock from Rhone-Poulenc's Maiden Rock silica pit located near Butte, MT. This paper will cover the design and excavation of the explosive drifts, the placement and priming of 190,000 pounds of explosives, and the backfilling of the drift to provide confinement of the charges.

Jan 1, 1993

By Tapan Goswami, Brent Geoff

Mining multiple steeply sloping coal seams introduces challenges in terms of safety and productivity. Work on steeply sloping surfaces for the processes of bench preparation, mark-out, drilling, loading and blast tie-up, coal cleaning and recovery is inherently hazardous. Furthermore, a large number of mining cycles is usually necessary, as small rounds are required and each layer is separately drilled, loaded, blasted and excavated. This exposes personnel and machines to additional risks and also incurs higher unit costs of mining as machine productivity is reduced. A case study is presented of a mine in New South Wales, Australia where three coal seams are separated by layers of inter-burden rock. Due to the unfavourable sloping nature of the coal seams the conventional practice was to drill and blast each layer separately.

Jan 1, 2010

By Selamawit Asfaw, Mohamad Sharif

In recent years, the use of modal analysis has increased to include many different aspects of the construction industry. Computer modal analysis can be used in determining the dynamic properties of a structure by mathematical equations and knowledge of the structure’s physical properties. This technique can now be used to predict the level of vibration induced by blasting on adjacent structures. Ground vibration induced by buried explosives is a major concern for contractors when excavating near utility pipelines such as gas and water lines. The size limitations placed on easements causes the necessity of additional utility lines to be placed in close proximity to existing lines. Through the development of computer models of the pipe, stress analysis can be performed prior to blasting. Based on the calculated dynamic properties (natural frequencies and modal shapes) and the maximum allowable displacements and stress levels (which are established by the pipe manufacturer) the allowable maximum charge weight per delay can be selected for the blast. The selected maximum charge weight per delay will ensure that the resulting pipe peak particle velocity level is within 95% confidence. This means, statistically, there exists a 95% probability that the actual pipe peak particle velocity would be less than the predicted value. The pipe is then instrumented with vibration measuring sensors to ensure that vibration levels are within the allowable maximum pipe strength. In conclusion, this technique can assist the engineers and blasters, to establish the proper blast design. It allows for safe and efficient installation of additional utility lines adjacent to existing lines. This technique can also be applied to predict the structural response to blasting induced vibration for a variety of complex structures. A detailed explanation of this technique, as well as an example of application including formulas used for this technique will be provided in this paper.

Jan 1, 2000

By Eric C. Gerst

"In this current era of soft commodity and coal prices the mining industry is turning towards optimizingall levels of production to reduce operating costs. Part of this trend includes the automation of miningmachines. As the first tier of the mining process blast hole drill automation offers benefits through the entire value stream from drill bench to material processing."

Jan 1, 2017

By Steven Richardson, E A. Cameron, Reza "Ray" Jambakhsh

This paper outlines the design and implementation of a method to use Long hole Carbide drilling to blast an "Upper Blind Slot Raise" in the range of 12m (40 ft).

Jan 1, 1992

By Tyler Acorn, Paul Worsey, Nathan Rouse

The effect of the hole diameter on vibration attenuation has not been incorporated in most vibration models in the blasting industry. In current vibration models, the charge weight and the distance from the blast are the two primary variables that are addressed. Charge weight is a function of explosive density, charge length, and charge diameter. This geometry-weight can complicate the isolation of the charge diameter variable.

Jan 1, 2013

By Miguel Humpire Huamani, Gustavo Huerta Valer, Jorge C. Cárdenas Miranda

As part of the continuous improvement and increase productivity to achieve the mining and extraction plan of a low-grade open pit copper operation, alternatives are required to expand the blast pattern to maximize drills and steels resources along to ensure the fragmentation results for the process plant with volumes from 500k tons of broken material per day. Therefore, the application of aluminum based ultra-high energy explosives was an alternative to achieve the objective of expanding the production pattern by 34% while maintaining energy factors levels along with the distribution of explosive and the application of the pocket charge in the stemming level, reducing the load factor, maintaining the fragmentation results in P80 and increasing the percentage of fines less than 1.0 in (2.54 cm). An important development to ensure the supply and perform successfully blasthole loading was the implementation of a supply system with pre-blending (aluminized emulsion) which is stored in silos and load through factory trucks. In the field we ensured optimal initial and final density levels with chemical sensitizer to perform the most fracturing work in the rock, complementary evaluations were performed to predict flyrock and define safe equipment evacuation radiuses along with advanced vibration monitoring for the sustainability of the mine.

Feb 6, 2023