Search Documents

By Nils Heinke, Stephen M. Collinsorth

To anyone who is responsible for the production of blast holes, who is looked to on a daily basis for drill maintenance and performance, whose bottom line may depend on the survival of the mine itself.. How much awareness should one have on such things that truly impact production, maintenance and overall job cost? Do you know your drill’s maximum capacity?

Jan 1, 1998

By Kis M

The purpose of seismic control of blasting is to indicate the vibration magnitude or to eliminate the occurrence of vibration damage caused by blasting. At the Mining Research Institute in Hungary, a new method has been developed to determine the method of delay. Near the blasting site (within 100-200 meters), the peak value of the particle velocity is determined by calculation and also by measurement. In the calculations, the time error of the electric detonators is taken into consideration. During the test program, the results of the experimental blasts and the calculated data have shown good correlation. The method of calculation helps the operator eliminate vibration damage, while the greatest quantity of charge can be detonated.

Jan 1, 1979

By Alastair Grogan

In October of 2002, the author was retained by Public Works and Government Services Canada, on behalf of the Department of National Defense, to design, construct and test the effectiveness of a bubble curtain system at an underwater demolition range, near Victoria, BC. The purpose of the bubble curtain was to reduce the potential for fish mortalities at the site. This paper presents some of the elements of the design, along with the results of overpressure monitoring during blasting and compares the results of fish mortality and animal behaviors with and without the bubble curtain in operation.

Jan 1, 2005

By Sedat Esen

"This paper presents a critical review of the fragmentation data obtained from some large open pit copper and gold mines. Database ncludes 35 mines with Uniaxial Compressive Strength values ranging from 19 MPa to 227 MPa (2756 psi to 32923 psi). Variation in the fragmentation data and the causes are discussed in detail. Quality assurance/quality control (QA/QC) in drilling and blasting was shown to have significant impact on fragmentation. In addition, controllable blast design parameters including drill pattern, powder factor, blast timing, stemming length, etc as well as the large blast sizes havesignificant potential to improve fragmentation. Feed size requirements of crushing and grinding circuits were discussed in detail. The paper discusses the effects of different size fractions (top size, 80 %passing size and % passing 10 mm (0.5 in)) on the downstream processes and the role of the fragmentation model in the mine to mill process. Blast domains based on rock strength and structure canbe established by using a fragmentation model which is calibrated using measured fragmentation data. This allows the blast engineer to compensate for changing rock characteristics and stabilize the ROMfragmentation size and result in increased crusher and mill throughput. Two case studies were presented to demonstrate the benefits achieved in downstream processes. Main benefits were reduced downtime at crusher circuits, improved mill throughput as well as reduced total operating cost. A simple relationbetween uniaxial compressive strength and powder factor was proposed using the database for the optimized mines as a guideline to allow site engineers to compare their sites against the other sites."

Jan 1, 2017

By Wayne A. Charlie

An experimental test program being conducted at Colorado State University and involves the study of the behavior of water saturated sands under shock and explosive loadings. The study is being conducted to evaluate potential blast induced changes in dynamic soil properties, soil shear strength loss (liquefaction) and densification of water saturated sands under single and multishock loadings. This paper presents testing and measurement objectives, and the equipment and instrumentation developed to load, measure, record and analyze the transient and long term soil behavior. The laboratory shock facility is capable of generating multi-shock pulses with milli-second rise time, peak stress amplitudes of up to 35,000 KPa (5000 psi), peak particle velocity of 5000 cm/set and peak acceleration of 10,000 g. The field explosive facility subjects saturated soil to controlled explosive loadings. Of major interest is the soil strain and water pressure, both during and after the passage of the stress wave, as a function of peak particle velocity, peak strain, loading rate, soil density, initial confining stress and the number of loadings. Based on data obtained to date, soil densification is due to consolidation following liquefaction.

Jan 1, 1991

By Don Larson, Gordon Coleman

The United States Department of Energy, through its contractor Lawrence Livermore National Laboratory, has entered into a contract with Alpha-IRECO, Inc. for the emplacement of approximately 2.9 million pounds of a 50% RX-MD emulsion 50% ANFO blend into an underground chamber for initiation to produce the 12 trillion caloric equivalent of 1,000 metric tons of TNT. The detonation will be closely monitored to determine the characteristics of a large chemical explosion for comparison with data collected from previous like-sized nuclear events in the same location. This data will be shared with former Soviet block countries to facilitate enforcement of the various non-proliferation treaties currently being negotiated between the countries.

Jan 1, 1994

By Edward Walter

Rock excavation for tunneling projects occurs on a regular basis in the Cleveland area. These tunnels are being constructed to increase the capacity of the sanitary sewer system. Controlled blasting must be performed to remove rock in a number of phases of the project. The rock excavation for construction of a junction chamber is just one case where blasting is the safest and most efficient method available.

Jan 1, 2001

By Charles Barnhart

This paper is a discussion of the causes of deflagration in cast blasting and a description of a project intended to demonstrate how changes in six critical parameters contribute to the deflagration chemical reaction. Control of these parameters is key to solving the nitrogen dioxide “orange smoke” problem. Preliminary results of an investigation into the development of a technology addressing the problem of atmospheric releases of nitrogen dioxide during cast blasting in surface mine operations are described. The project is funded by a $600,000 Small Business Innovative Research grant from the National Science Foundation and an $80,000 Abandoned Coal Mine Land Reclamation Program grant from the state of Wyoming. The presentation will address the measures required to control the blast chemical reaction so that it does not produce nitrogen dioxide through deflagration. Experimental blast data will be focused on a new shaped charge detonation system designed to instantaneously bring the powder column to maximum velocity of detonation (VOD), thus insuring efficient detonation of the entire colulnn.

Jan 1, 2003

By Steve Dillingham

PHYSICAL BLAST DATA Pattern Description All measurements related to the description of the physical blast pattern must be made with the mind-set that it has to tell a powerful factual story enabling a future accurate reconstruction of the event. A case has never been lost because too much factual information was available to assist investigators. An accurate physical description of the pattern must be provided based on the blaster’s observations of the pattern actually loaded. The blaster must measure the pattern size, depth, face heights, etc., recording only accurate results. All too often, a blaster records simple pattern sizes and information relayed to him or her from the driller, or from a phone call into the office the night before for powder pre-load inventory purposes. If a pattern was actually measured on the job site by the blaster to be 8.5 x 9.5’, it may, in fact, originally have been ordered at 9’x9’, 8’x9’, or 9’x l0’. In a claim situation, particularly flyrock, recording a “generalization” of what was loaded could result in an interpretation of a blaster’s negligence due to “not knowing or caring” what the actual pattern was, and not loading appropriately for conditions. It is important to remember that other documentation exists such as a drill log from a contract driller or mine records that may provide a different interpretation of the loaded pattern.

Jan 1, 2002

By Robert B. Hopler

Explosives, originally used only in fireworks and warfare, became legitimate contributors to human progress when miners in Eastern Europe began using them to break rock in the early 1600%. Since that time these powerful materials have had a dual role in the world: as agents of destruction in war, and as irreplaceable tools necessary to advance civilization. In the latter role, they serve as agents to enable mankind to produce metals, build roads, and drive tunnels. In other words, to provide those materials, services, and infrastructure without which the modern world could not exist.

Jan 1, 1997

By P D. "Takis" Katsabanis

The phenomenon of sympathetic detonations in blastholes is investigated by comparing experimental observations and numerical modelling results. Numerical modelling using the TDL computer code and Forest Fire decomposition rates for commercial explosives has shown the importance of blasthole diameter, impedance of the stemming and host rock. Comparison with experimental observations has also shown that sympathetic detonations cannot always be treated as shock to detonation transition. Examination of previous results which have been obtained from calibrated low amplitude shock experiments reveal that there is an ignition threshold prior to the detonation threshold. The difference between the two thresholds is more pronounced in the case of air bubble sensitized products. The ignition threshold can be very important under the confinement provided by the blasthole and the conditions of application. It also correlates well with the pressures expected at the gap distances of interest in the practical application. It is suggested that critical energies are used as the criterion for cross initiation in blastholes. Practical suggestions based on the numerical calculations and experiments based on these calculations are also given and discussed.

Jan 1, 1991

By Donald Thompson, Jessie Bonner, Ileana Tibuleac

Predicting ground motion from complicated mining explosions is important for mines developing blasting programs in regions where vibrations must be kept below certain levels. Additionally, predicting ground motion from explosions in complex 3D media is important for source size estimation for nuclear treaty monitoring. Both problems have been addressed under the development of a new series of programs including: 1) Generalized Fourier Methods to generate synthetic seismograms (Green’s functions) in 3D media for a moment tensor source implementation and 2) MineSeis3D, a program that simulates seismograms for delay-fired mining explosions with a linear relationship between signals from small size individual shots. To test the programs, three-component seismic recordings of three production shots at an iron mine in northern Minnesota were compared to synthetic waveforms in 3D media. Comparison of the observed and synthetic waveforms shows promising results. The shape and arrival times of the normalized synthetic and observed waveforms are similar for most of the stations. The synthetic and observed waveform amplitude fit is best for the vertical components in the mean 3D model but not as promising for the transversal components. The observed effect of spall on the waveform spectra was weak in the case of fragmentation delay-fired mining explosions. Commercial applications of the code could provide data needed for designing explosions that do not exceed ground vibration requirements posed by the United States Department of Interior, Office of Surface Mining.

Jan 1, 2005

By Darío Innamorati, Jorge Oliva

Cerro Vanguardia is a known gold and silver deposit located in the province of Santa Cruz, Argentina. The mine has been in operation since 1998 and is thought to be one of the most important mines in Patagonia. More than 102 epithermal quartz veins have been identified in the area, with variable lengths, thicknesses, orientations and dips that constitute what is possibly one of the most extensive outcropping vein systems on earth. Veins are vertical and have variable depth. For this reason, the deposit is currently mined with a variety of extraction methods. This operation is made up of more than 60 open pits and 20 underground access ramps to exploit the deepest high grade narrow veins. This study is focused on the combination of underground exploitation with open pit blasting. That is, those production stopes in the upper levels of underground mines and their interaction with the damage levels in the final slope of open pit mines, as well as in the study of the impact of the generation of vibrations from the blasting of open pit mines and their influence on underground mines. Considering the current stage of the mine, after 20 years of operation, Cerro Vanguardia faces the need to mine deeper deposits in the face of increasing costs and declining grades. For this reason, it is essential to study the interaction of these exploitations. From a personnel safety point of view, this interaction must be well coordinated so as not to affect people and equipment. Likewise, the generation of vibrations due to blasting must be studied, which would produce new cracks, potentially generating overbreak and dilution. The main objective of this study is to determine the possible causes and influences of the blasting interaction in open pit and underground mines, seeking an optimization of the blasting process and a safety standard for personnel and equipment. To achieve these goals, this study includes a vibration monitoring plan to analyze the charge performance and determine rock constants. With the use of specialized software, damage modelling and simulations are used to determine values of damage in order to reduce overbreak. In addition, this plan contemplates the estimation of flyrock in blasting where underground work is connected to the surface, determining safety distances when carrying out a blast.

Jan 21, 2025

By Dennis R. Jr Bell

Before beginning any site development or mineral extraction activity, it has been well documented that it is first prudent to gain an understanding of the prevailing geologic conditions.Whether it’s identifying the depth to type of bedrock, or determining the quality and quantity of the in place mineral deposit, these factors should always be considered in a project’s fatal flaw analysis. In situations where there is limited subsurface information, geologic models have been proven to be one of the most valuable and cost-effective tools used by the developer and/or his consultant.

Jan 1, 1997

By G. R. Adhikari

Step 4: Selection of explosives and initiation system Various types of explosives are manufactured in India and a wide choice is available among them that include nitroglycerin based explosives, slurries, emulsions, ANFO (ammonium nitrate mixed with fuel oil) and heavy ANFO. The choice is also available between cartridged and bulk loading systems. In Indian mines, much importance is unduly given to the cost of explosives alone which is not conducive to optimization of blast design parameters. The concept of energy per meter of blasthole and the way in which the total explosive energy is partitioned between shock and heave is not considered in the prevailing practices. Besides, very little efforts are made to objectively evaluate the performance of explosives for a given site condition. Tailoring explosives is limited to changing the density of the bulk explosives. Cartridged explosives are still being extensively used in large operations where bulk explosives should be the preferred choice.

Jan 1, 2002

By Jean-Guy Levaque, Robert Ethier, Ron J. Elliot

This paper presents data gathered during a comprehensive study on the impact of improvements to fragmentation in a major Limestone quarrying operation. The full impacts of gains in fragmentation are tracked through the mucking, crushing, and grinding phases of the operation.

Jan 1, 1999

By Dale S. Preece

A Discrete element computer program named DMC @istinct Motion Code) has been developed for modeling rock blasting. This program employs explicit time integration and uses spherical or cylindrical elements which are represented as circles in 2-D. DMC calculations have been compared with measurements on bench blasts in the field with relatively good comparison. Structural rock mass characteristics have a significant impact on any blast and DMC has not, until now, included these effects. This paper discusses a recently added DMC capability for treating joints and bedding planes in bench blast simulations.

Jan 1, 1995

By Michael Wieland

For shooting rock properly, some relatively fixed quantity of rock work is required from the total charge mass, while keeping the overall toxic fumes to a minimum. The overall fumes weighted for the toxicity of different species and taken per unit charge mass, ??, are represented by a relative fume toxicity (RFT) formula. The worst two contributions are often carbon monoxide {CO} and total nitrogen oxides {NOX}, so the traditional Russian formula RFT-R formula suffices, though a generalized form RFT-G with more terms is worth checking. Using the work-principle model from thermodynamics, the rock work per unit charge mass, ??, is found from the reduction in internal energy for the reaction zone. This resolution technique for rock-work invokes the usual assumption that the quick irreversible process occurs without notable heat transfer to the rock (adiabatic); rock-work is not resolved, when this restriction is untenable. The ratio of ?? to ?? yields the weighted toxic fumes divided by the rock work or the readjusted fume toxicity ??, where ?? = ??/??. For convenience, graphical trends of ??, ?? and ?? were normalized using reference results for a stoichiometric (ANFO) mixture of ammonium nitrate (AN) and fuel oil (FO) shot under nominal rock confinement, noted later.

Jan 1, 2006

By Paul Worsey, Larry Frost, Braden Lusk, Seok Bin Lim

For certification of blast resistant windows, current tests consist of arena tests or large air gun tests. Arena tests involve the detonation of more than 1000 pounds of explosives with windows placed in the range of hundreds of feet. The result of an arena test is a loading on a window consistent with an expected industrial or terrorist blast. Due to the nature of this type of test, only a limited number of facilities are available and operational costs can be extremely high. Air gun tests involve the use of compressed air and a failing diaphragm fired through a large tube. Although this test is more cost effective and easier to administer with lower environmental impacts, it is not an explosive loading and does not create a negative phase on the tail of the pressure pulse. Simply using a small charge in close proximity to the window is not a viable option either. The pressure peak can be reached using this method, but the duration of the pressure pulse is such that the positive phase impulse is on the order of ten times less than that for an arena test.

Jan 1, 2006

By Gunnar Persson

The borehole pressure/time history of blasting practice is simulated in a twin pendulum apparatus, where the expanding shotfiring gases force two steel slab swingers apart. A pilot installation built at SveDeFo is described. The relevant factors, that govern the use of this test method as a means of classifying explosives with respect to their toxic fume potential, are described.

Jan 1, 1996