Search Documents

By James Rowland, Isaac Zlochower, Richard Mainiero, Michael Sapko

The National Institute for Occupational Safety and Health (NIOSH) carried out exploratory laboratoryscale studies to identify factors that may contribute to nitrogen oxides (NOx) production associated with non-ideal detonation of blasting agents. Explosive admixture with drill cuttings, loss of fuel oil in ammonium nitrate and fuel oil (ANFO) from wicking, ammonium nitrate dissolution with water, degree of explosive confinement, ANFO density, and critical diameter were identified as contributing factors to increased NOx production under the laboratory test conditions. Experiments were also conducted to examine the effectiveness of various additives in reducing the NOx production from ANFO, emulsion, and ANFO/emulsion blends. Aluminum powder, coal dust, urea, and excess fuel oil in ANFO formulations were tested and were found to reduce both the nitric oxide (NO) and nitrogen dioxide (NO2) production. Fumes measurements were obtained in the NIOSH underground closed chamber from the detonation of 4.5-kg (10 lbs) charges in schedule 80 seamless steel pipe and from detonations in light weight galvanized steel stove pipe. Some exploratory tests were also conducted with 0.8-kg (1.8 lbs) charges of pulverized ANFO initiated with 0.08-kg (0.18 lbs), 50/50 (Pentolite) boosters (in the NIOSH 12-ft (3.7-m) diameter steel sphere) to measure the degree of fumes production associated with post-detonation oxidation. Ammonium nitrate, emulsion and Pentolite boosters were also detonated in an oxygen-poor environment.

Jan 1, 2002

By Laurence Neufville

Proper risk assessment and blast design are very desirable to the execution of a blast. Not only will this ensure that it achieves its desired outcome, but the probability of complaints and litigation will be reduced. Blasting engineers rely heavily on site-specific data for analysis and input to the blast design equations, and therefore data collection is critical to this process. The traditional approach to data collection is to carry out site-specific reconnaissance by visiting the site, but the time spent doing so can be reduced if a remote sensing approached is adopted.

Jan 1, 2009

By Adrian J. Moore, Alan B. Richards

Airblast overpressure levels can commonly be increased by up to 20 decibels (dBL) by the effects of meteorology, due to inversions and wind shear. Existing atmospheric refraction models can provide a good evaluation of the effects of meteorology, but have been limited in the accuracy of their outputs by the accuracy of the meteorological data that is available for input. This paper uses case histories from open-pit coal mine blasting in the Hunter Valley area of Australia to provide examples of increases in airblast due to inversions, wind shear, and a combination of both. It gives details of our experience of the accuracy with which predictions and assessments can be made using meteorological data of various levels of accuracy, and on the design buffer that is required to prevent the exceedence of airblast limits. The accuracy of meteorological prediction and assessment will shortly be improved by the use of sounding equipment that gives continuous measurements of temperature and wind velocity at significant levels above the ground. The paper also gives details of an industry funded research project that aims to permit the effective use of this data at distances many kilometres (km) (miles) from the location of the sounding equipment, and to develop a short term predictive model that will permit the amount of meteorological reinforcement that will occur at firing time to be determined before a decision is made to tie up a shot.

Jan 1, 2005

By Santiago Gómez, Pablo Segarra, José A. Sanchidrián

In this paper, differences between the industry-standard Holmberg-Persson (H-P) approach and a semi-analytical vibration prediction model called full-field solution (FFS) are analized. The analysis is conducted at two levels: vibrations and rock damage.

Feb 1, 2020

Blasthole deviation is a frequent, well documented and undesirable occurrence in mining operations. It is caused by the drill string mechanics, operating variables and the interaction between the drill bit and the rock mass characteristics. It is composed of three distinct components: collaring or marking error, alignment error and trajectory deviation. This study has focussed on the dependence of trajectory or natural deviation on the geological features of the rock mass being drilled.

Jan 1, 1996

By Duncan Chalmers, Rob Nowell, Miguel Araos

Australian underground mines produce in excess of 60 mtpa of coal. Most of these use the longwall method, and they require the use permitted explosives (which are called “permissible” in other countries) for challenges that appear during the day-to-day activities. To obtain the approval for these explosives, they should pass Testing Memorandum #2 (TM-2), which sets out the test required for each category of permitted explosive. These categories are P1, P3, and P5. With P5 being unrestricted use and P3 and P1 have conditional use in underground mines. The TM-2 test was originally set up for NG-based permitted products around 1900. With the closing of NG plants around the world, ammonium nitrate explosives were the natural replacement, and therefore these explosives need to pass the TM2. Australia does have a P1-emulsion based explosive available. For high-risk scenarios (like blasting coal), no P5 explosives are available. The lack of P5 explosives has been prolonged for more than 25 years, since the phasing out of nitroglycerine-based permitted explosive products around the world. The main problem has been that when emulsion based permitted products are tested in the deflagration cannon, the results obtained were not considered in the TM2 criteria and therefore the tests were invalid. A research work on permitted explosives began in 2005 funded by the Australian Coal Association Research Program (ACARP). The aim of the project was to address the lack of P5-type permitted explosive (and, potentially develop them further, i.e., develop safer explosives) and understand the behaviour of emulsion explosive and the results they presented in the tests. Both bureaucratic and technical barriers appeared along the way. On the bureaucracy side, the facility was shut down, reopened, and shut down again. In view of these difficulties, assistance was sought overseas. On the technical side, from the very start the results of the tests when using emulsion-based permitted explosives were not established in the criteria, ignitions occurred for trial samples that were expected to be P5-type, etc. The aim of this document is to present the painful journey in the Australian industry to have a P5-type emulsion-based permitted explosive, for use in UG coal. Also, the technical learning acquired about emulsion explosives and the ignition path of mixtures methane / air will be shown.

Jan 21, 2025

By Roger S. Jackson

"This study interprets vibrations produced by single underground shots, recorded on surface by 135 digital seismographs laid out in four linear arrays. Several vibration anomalies were observed and are investigated. A novel method of displaying the blast-induced vibration iso-contour data relative to the three-dimensional representations of the geological rock units and structures leads to the following interpretations:• The identified faults commonly dampen or amplify vibrations, on the evidence of the peak particle velocity,• Strong anisotropy of geologic formations produces different vibration attenuation in the various directions of interest,• Low-vibration “depressions” can be related to the presence of faults, and• Higher vibration levels than expected based on ‘scaled-distance’ principles are observed close to intersecting faults.The interpretations from this study document a better understanding of the geotechnical influences on blast induced stress wave propagation in a geologically complex area. The practical benefit of this understanding is better control of surface vibrations, experienced from underground mining activities."

Jan 1, 2010

By W. Sharkey Bowers

This study was undertaken in order to determine a conservative estimate of the attenuation rate of vibrations through the shallow limestone in South Florida due to quarry blasting.

Feb 1, 2020

By M. Szumny, P. Mertuszka, K. Fuławka

Multi-face destress blasting is the basic method of reducing rock bursts hazard in Polish copper mines. Blasting operations of this type are carried out regularly, twice a day in order to minimize the geomechanical threat while maintaining high extraction efficiency. Unfortunately, the assessment of the effectiveness of this type of work until recently was based solely on determining whether a given destress blasting triggered a seismic tremor or not. Information on the characteristics of seismic waves generated by blasting has so far been omitted in analyzes of this type. The lack of reliable knowledge about the generated seismic effect makes the introduction of constructive corrective actions impossible, which in turn significantly reduces the triggering potential of conducted destress blasting. This study presents the results of comprehensive work aimed at increasing the effectiveness of active rock burst prevention in Lubin underground copper mine. For this purpose, an innovative system for continuous monitoring of seismic waves induced by multi-face blasting was developed, and a new method for seismic assessment of the effectiveness of the destress activities was developed. Based on the monitoring data and the comprehensive analysis of waveforms, the effectiveness of individual blasting operations was determined, and on this basis, modifications to the drilling and blasting patterns aimed at increasing the generated seismic effect were proposed. The use of innovative methods of monitoring and data analysis made it possible to increase the effectiveness of the conducted activities, in terms of the magnitude of seismic vibrations, up to 250%. It should be emphasized that the introduced modifications were aimed at increasing the effectiveness of blasting operations while maintaining the current level of costs. As a result, the proposed solution turned out to be highly effective, significantly affecting the safety of the work carried out in Polish copper mines. Thus the proposed approach is planned to be implemented in other Polish copper mines belonging to KGHM in the near future

Jan 1, 2024

By Carl Lubbe, Ron Frye

Numerous articles have been written regarding the effects of blast control plugs in an attempt to quantify stemming ejection rates, air overpressures, fragmentation’and other parameters measured using these devices. In an effort to further attempt to understand the function of these devices, field and laboratory research conducted with various stemming devices was performed to enhance existing data sets and analyze otherphenomena that occur when these products are used.

Jan 1, 1998

By Owen Collins

In surface mining, designing patterns to reduce the probability of flyrock and optimizing fragmentation through powder factor calculations are important for safe, efficient blasts. The designed powder factor is established for the blast once parameters such as burden, spacing, stemming, and powder column height are determined. In practice, these parameters are usually constant throughout a production blast with row-to-row burden and spacing. However, challenges can arise with the introduction of an open face. Many variables could necessitate the adjustment of the face row to optimize blast results. Variables include drill accessibility, challenges with toes, overhangs, and geology. The approach is often, but not exclusively, determining how to keep a consistent powder factor from the open face through the body of the blast. However, the solutions used vary case-by-case and rarely are two blasts the same. Technology has improved the ability to deal with challenging face conditions. 3D modeling with the aid of drones allows the application of angled holes to be more effective and simpler. This is just one instance where technology has improved blast results. This paper will present solutions to challenging face conditions. Thoroughly analyzing instances where challenging open-face variables were met with an effective blast solution could help provide insight as to what yields consistent blast results.

Jan 26, 2026

By Rob Farnfield, Ben Williams, Bob Woolley

This paper outlines how drilling safety standards are being driven forward in the United Kingdom’s surface mining and quarrying industry with developments in equipment, procedures and competence.

Jan 1, 2010

By Rob Farnfield, Ben Williams, Ashley Haslett, Diane Cartledge

Major accidents that occur within our industry are often tragic and expensive, damaging reputation and threaten the livelihood of the business. There isn’t anything in them that can be seen as positive for those that experience them. They undertake what are usually very painful, detailed and time consuming investigations to discover how the incident occurred and what needs to be done in the future to prevent similar incidents occurring. Many admirably choose to share the lessons learnt through industry organizations such as SAFEX International so that we can all have the opportunity of preventing similar incidents from occurring within our own organizations.

Jan 1, 2016

By Jean-Sébastien Lambert, Serge Roberge

"At the end of 2014, Holcim Canada (Demix Aggregates Division) considered the possibility of drillingand blasting a big volume of rock in order to expose a high-quality limestone bench in one of their urbanarea quarries in Laval, Quebec (Canada). The project includes many challenges and has thus been qualified as a high-risk operation."

Jan 1, 2016

By Thierry Bernard

This case study shows how a unique combination of field measurements and advanced technologies allowed blasters designing, loading and firing an incredibly challenging quarry blast.

Jan 1, 2015

By M. Szumny, P. Mertuszka, K. Fuławka

Mining-induced seismicity is one of the adverse side effects of mining with the use of explosives at great depths. Disturbance of the primary stress state by the development of the network of excavations combined with the continuous generation of dynamic loads by the detonation of explosives in mining faces has a negative impact on the level of safety of crew and machines. To ensure the stability of excavations it is necessary to identify in detail the nature of the seismic hazard by means of continuous seismic measurements. Unfortunately, the technologies used so far are characterized by high costs of installation and further maintenance, which clearly limits the possibility of using a large number of stations in a small area. A breakthrough in this matter may be the technology of microelectromechanical systems, which is several times cheaper than standard solutions used in mining seismology. This technology, with the appropriate configuration of devices, can be successfully used to monitor dynamic phenomena generated by mining activities. As part of this study, the assumptions and configurations of a prototype 42-channel accelerometer network using MEMS technology have been presented. The network was installed in the Lubin underground copper mine in Poland in a seismically active area, where multi-face destress blasting are conducted regularly. As a result, 14 tri-axial accelerometers were installed in the immediate vicinity of the active mining front at a distance of about 1,000–4,000 ft (300–1,200 meters) from the closest faces. Highfrequency recordings are collected based on algorithms that trigger the system when the Peak Particle Acceleration set value is exceeded or on the basis of a manual external triggering device connected to the blasting machine. During the measurement period, several high-energy seismic tremors and several dozen of waveforms generated by blasting were recorded. The obtained results are the basis for assessing the effectiveness of the destressing measures and for the analysis of geomechanical risk based on periodic analysis of the velocity of seismic wave propagation

Jan 1, 2024

By Stuart Brashear, Eddie Colburn

The Birmingham Coal and Coke – Knight Mine is a single seam coal mine in central Alabama. As pit development progressed in 2013, concerns over increasing vibration levels resulted in modifications to the blasting program that inhibited shot size and coal recovery. By January 2014, while still over 1,400 feet (427 m) from the regulatory seismograph, vibration levels climbed above 70% of the mine permit limit, even with triple decking of holes and reduced burden and spacing. At this time the decision was made to commit to the use of signature waveform analysis and precision programmable electronic detonators to minimize vibration and maximize the amount of coal that could be recovered before vibration levels reached permit limits.

Jan 1, 2015

By Martin Langenderfer, Catherine Johnson, Phillip Mulligan, Kelly Williams

The physical geometry of a charge has a direct correlation to the geometry of the shock wave. This relationship appears strongest within the boundaries of the visible fireball. As the shock wave propagates outward past the limits of the fireball, the theory states that the geometry of the shock wave should even out and become more spherical. This paper investigates pressure vs. time at two distances, one ‘Near Field’ at the extent of the fireball and one ‘Far Field.' The two Fields were instrumented with three free-Field pressure probes from PCB oriented at 0, 45, and 90 degrees to the front face of the charge, in the same horizontal plane as the charge. This orientation allows for the comparison of the shock wave from the face and vertices of the charge. All the pressure sensors were connected to a Data Acquisition System (DAS) recording at 2 million samples per second (2MS/s). Two high-speed cameras, a Phantom and an MREL Ranger II, recorded the detonations for qualitative examination of the fireball, and the shock wave. Three charge geometries were used and compared to the shock propagation of a sphere. The other geometries tested are cylinders, cubes, and tetrahedrons. Charges were made from a PETN based sheet explosive. In the Near Field, a lower pressure is observed along charge vertices with highest pressures from each face. In the Far Field, vertices record a higher pressure, possibly due to the shock waves from the adjacent faces intersecting, indicating that shock pressures do not always even out in the Far Field. This paper will describe the methodology and findings of this experiment and attempt to determine causality for trends in the data gathered.

Jan 1, 2018

By Lon Santis, Dale Ramsey

The use of aircraft to support blasting operations in mines, quarries and construction sites goes back to the early days of aviation. Invaluable at times, aircraft use has been limited by cost, the unpredictability of weather impacts and other factors. Recently several technologies have matured to open up a new way to acquire aerial data with unmanned aircraft systems (UAS), commonly called drones. Equally important, the U.S. Federal Aviation Administration has recently implemented an exemption process and rulemaking to implement the commercial use of UAS into the United States’ National Airspace. The skies are opening for many applications of UAS. The most notable may be photogrammetry, which is the science of making measurements from photographs, especially for determining the exact positions of surface points.

Jan 1, 2016

By Iván E, Alex Araya Jofre, Jean Guiroux Toro, Eduardo Valdés Guerra

Currently, it is important for companies to have controlled mining operations and adhere to production schedules. To achieve this, one of the key factors is maintaining high reliability in the P&T process, primarily the opening of ore stope, which could be delayed due to any unplanned or uncontrolled problem. These ore stope opening processes, whose main activity is generating free face, are a very important pillar for future mine planning. The possibility of ensuring their opening brings a series of downstream benefits: safety, economics, productivity, and compliance and adherence to plans. The process under discussion consists of developing free faces in a single blasting event. This will help us leverage greater reliability for overall production operation plans, reduce construction times, and open up opportunities for downstream improvements in the production process, considering technical factors in P&T designs. This study presents a developed methodology and shows the results of its implementation in ten (18) single-event free face blasts. The analysis includes cavity geometry, geology, rock qualities, drilling deviations, and the blasting strategy implemented for each event. The methodology used considered material fluffing processes, the actual drilling trajectory, the initiation sequence, QA/QC during explosive loading, monitoring instrumentation (vibrations), and VOD recording, among others. As a result, out of a total of 18 free-face events blasts in a single event, 16 were successful and two achieved 90% efficiency, reducing the stope's production start-up time by 50% compared to current operations. By implementing free face blasting in a single event, there are savings in operating costs, increased productivity of the mining equipment, and improved adherence to production plans. For applications with greater heights of free faces, where blasting cannot be carried out in a single event, we should consider performing them in two stages using wireless detonators already available on the market for mining operations.

Jan 26, 2026