Search Documents

By Douglas Rudenko

When blasting complaints come, as an industry we often immediately look to the ground vibration as the source of the trouble. Often times we overlook or place less emphasis on the collected air overpressure data. Air blast like ground vibration is an undesirable side effect of blasting and can produce considerable structural response.

Jan 1, 2002

By George Young Mosteller

This paper is summary of the practical solutions developed in the excavation of drilled piers (caissons) at GPCo's Plant Scherer, Juliette, GA. Plant Scherer is a 3,245 Megawatt Fossil Fuel Powerhouse and, when completed, will be one of the largest fossil fuel plants in the Southeast.

Jan 1, 1980

By W. J. Birch, R. Farnfield

All shock-tube based initiation systems have a time lag relating to the propagation velocity of the shock-tube itself. This paper examines the exploitation of this inherent time lag to achieve delay blasting with accuracies approaching that achievable with electronic systems albeit over a much shorter delay range. The system employed consists of a combination of standard shock-tube, plain detonators and various shock-tube branching components. The accuracy of the complete system depends on the scatter in delay time induced by each component. In order to quantify this scatter a series of trials were undertaken to determine the variability for each component. These trials are described along with a detail statistical summary of the data recorded.

Jan 1, 2009

By Robert C. Brown

During a research period lasting over three years, a vast number of seismograms were collected and analyzed. From this data, other than obtaining a host of new information pertaining to the effects of surface mine blast on underground mines, it was found that by mounting seismograph velocity transducers at the center of crosscuts in underground mines, seismograms can be obtained which give fairly accurate information about the maximum levels of vibration, and the associated Of stresses and strains, misfiring of blast holes, delay accuracy and delay overlap. The technique of analysis is a simple one; it involves matching of the frequency of wave or wave groups with the shot card information such as rows of holes, number of holes and the cumulative milliseconds of delays used in the blast holes. Any discrepancy that might exist between the frequency of waves and the expected cumulative millisecond delay for a given row or hole eventually will show up as a mismatch in the analysis. This simple technique enables the seismographer to be involved not only in the monitoring of blast peak vibration, but also in making recommendations as to the choice of millisecond delays, reducing the possibility of delay overlaps and reducing the hazards of blast hole cutoffs.

Jan 1, 1980

By Dale Ross, Bill Clements, Jim Spanos

Current world conditions are forcing the search for "green" energy technology in every aspect of our daily lives. Finding alternatives to petroleum fuels seems to be at the top of the list. The search for the "perfect" alternative is something like the never ending quest of the perpetual motion machine. Unfortunately, the laws of physics prevent us from getting something for nothing, and Murphy's Law normally gives us nothing for a lot of something. Regardless of Murphy, the quest goes on, and in our industry cheaper ANFO seems to be the popular subject.

Jan 1, 2012

By M Sampara, W Comeau

The introduction of large-diameter holes to underground mining has made possible the development of new mining methods such as the Vertical Crater Retreat (V.C.R.) method. It is not only the safest underground excavation system but also provides mass production at a lower cost than any conventional mining method (1, 2, 3, 4, 5).

Jan 1, 1981

By Tapan Goswami

A column of stemming material keeps explosion gases at high pressure for longer times in a blasthole. In general, use of appropriate stemming enables the achievement of the desired level of fragmentation and looseness of muckpiles, as well as the reduction of airblast and fly rock. The ejection resistance of a stemming column varies with the type of stemming material employed. In an effort to optimise stemming at Mt Owen Mine in the Hunter Valley, Australia, a trial was conducted to assess the efficiency of two types of stemming materials. Mt Owen mine relies on through seam blasting and stemming quality is important in this challenging blasting environment. Each type of stemming was trialed in different section of a blast. The blast was designed using Orica’s SurveyPlus@, LoadPlus@ and ShotPlus@ software. Measurement was done using high speed filming of the blast and then post blast information was obtained from analysis of the film. Data analysis included determination of the ejection velocities and percentage swell. Digging rates were measured from excavator production rates. Despite the presence of rounded surfaces and finer particle sizes, River Pebble stemming material showed superior ejection resistance. It also appeared to perform as well as more angular and expensive Crushed Stone, a finished quarry product, based on excavator productivity and heave. It was recommended that future blasts at the mine be stemmed with the River Pebble stemming material.

Jan 1, 2000

By Gary Anderson, J. P. Remi Proulx

Rio Tinto’s Colowyo Coal Mine produces 2.1 million tons per year in northwest Colorado. Colowyo uses the terrace mining method to recover up to seven coal seams ranging in thickness from 5 to 20 feet. Coal recovery in the 6 foot thick high grade C-seam has recently been challenged due to large variations in the pitch and roll of the seam. As well, some coal damage was seen due to an increased thickness of the overburden consisting of a hard sandstone channel.

Jan 1, 2012

By R Heater, G Glynn

Various small diameter commercial grades of slurry and emulsion explosives were tested and compared. Velocity diameter curves for confined and unconfined charges were established and the effects of temperature and hydrostatic pressure on critical diameters and minimum primer weights were determined.

Jan 1, 1984

By Michael Wieland

Sharp transient stress waves generated during the delay blasting of underground coal can damage unfired borehole charges remaining in the delay pattern. These tremendous stress pulses in coal bear a strong resemblance to underwater shock waves, despite differences in rise times, damping rates, and scaling relations. "Shock wave" terminology is adopted to distinguish the sharp transient waveforms propagating through the coal from the gas-driven stresses that rift the coal. Reported waveform characteristics of shock waves through underground coal were utilized to design a simulator test for rating the impact resistance of cap-sensitive explosives. Theoretical minimum borehole separations were determined for each cap-sensitive explosive from the requirement that worst-case waves hitting an unfired charge would not exceed its impact resistance rating. Rugged explosives have higher impact resistance and will function properly at smaller borehole separations. Additional work is required to verify the findings from the simulator technique and modeling relations reported here.

Jan 1, 1990

By Sterling Ziegler, Kameron Ray

Mining operations at a Wyoming coal mine were progressing to within 300 feet (91 meters) of a high pressure natural gas pipeline. Vibration levels from cast blasting were at a point at which standard designs would exceed permitted limits and could potentially damage the pipeline. Without a confident vibration model, mining would be unable to continue in the pit rendering an entire cut of otherwise mineable coal sterile. To safely blast in the area, linear superposition seedwave analysis techniques were attempted to be used to create a model that could accurately predict the vibration at the pipeline. Four signature holes were fired individually. The four signature waveforms were monitored at eight discrete locations to create thirty-two vibration data points. Two of the monitors were equipped with triggers enabling the calculation of p-wave velocity.

Jan 1, 2018

By Y. Idrogo

Electronic delay detonators have been used in most types of blasting application with great success, with the accuracy and precision being used effectively to control negative environmental impacts like vibration. They have also provided consistent repeatable fragmentation and heave results. With the very wide choice in delay period and powerful timing design software, the choice of firing times to optimise blast results is not always clear to the designer. So the improved results achievable from the use of electronic delay detonators are often not optimally achieved.

Jan 1, 2018

By Ron J. Elliott, Corry Coumans

The following is a detailed description of the blasting procedures used in the successful demolition of the Stave River bridge, Mission, British Columbia, Canada. This highway bridge spans a highly sensitive salmon-spawning river. Demolition of the bridge took place in a high liability situation in close proximity to sensitive structures. The new highway bridge carrying an exposed 150mm diameter gas line was located only 1.5 meters away. The bridge piers were blasted only seven meters from overhead power lines. Control of blast vibration, flyrock, and underwater overpressure was critical to the success of the operation. Electrical sequential blasting was used to ensure that blast vibration on the new bridge structure was kept below 50mm per second.

Jan 1, 1998

By Andrea Francioso, Roberto Folchi

In order to comply with the latest European Highway Standards, the highway Salerno - Reggio Calabria, in southern Italy, had do be widened and upgraded to reduce its vulnerability to earthquakes. Reinforced concrete viaducts, no longer needed for the new road, had to be demolished. Many bridges still to be used for the highway required refurbishment due to 50 years of wind, frost and salt corrosion. This re-furbishment and new construction had to be carried out simultaneously. To keep the highway open dur-ing the renewal process, all traffic was directed to one side of the road. Demolition was conducted ex-tremely close to operational roadways and viaducts, as close as only 2 cm (0.8 in). Care had to be taken to ensure that the stresses (vibration levels), resulting from the demolished pylons and decks hitting the ground, were below the no-damage thresholds for the nearby acceptors (structures receiving the vibra-tion stresses). These structures included bridges, houses and buried pipelines (water, oil and gas). In some cases, care also had to be taken to preserve the existing pylons supporting decks that were being demolished; since the same pylons were going to be used for the new viaducts (bridges). New continu-ous decks in weathering steel replaced the old reinforced concrete decks.

Jan 1, 2013

By P D. Katsabanis, K Steeves, D Dombrowski

Accurate electronic detonators with firing time accuracy within 100 microseconds of the nominal have been used to control blast results in terms of fragmentation, vibrations and wall control. Axisymmetric experiments and experiments utilizing small benches have been conducted in order to calibrate a numerical model under development and examine the influence of delay interval on wall control, fragmentation and vibrations. The results obtained so far indicate definite advantages of precise timing in reducing back break and wall damage. Fragmentation is affected by the delay interval and high speed film observations and measurements indicate that the delay interval should allow the damage zone from each blasthole to be fully established prior to the detonation of the next borehole. Studies on vibration control demonstrated that vibration synthesis work using signature shots can only be of use if accurate delays are employed.

Jan 1, 1995

By Piyush Rai

Proper use of fi ring pattern vis-à-vis the blast requirements can provide optimal blast performance in terms of fragmentation. Further to this, each fi ring pattern has its own characteristic, for instance, although V-type and diagonal fi ring pattern provide same Se/Be ratio, the V-type fi ring pattern increases the opportunity for in-fl ight collision amongst broken rock fragments during their movement. Similarly straight V-type and skewed V type fi ring patterns (V1,V2 etc.) have their own characteristic strengths and weaknesses. In this light the present paper highlights the application of three different types of fi ring pattern on two different type of sandstone overburden benches of a large coalmine in India. The study reveals that Firing pattern infl uences the effective spacing to burden ratio at the time of detonation. By changing the fi ring pattern, effective burden (Be) changes and the ratio of effective spacing (Se) to effective burden (Be) during the fi ring is also subject to change in comparison to drilled spacing to burden ratio (S/B) Hence, the Se/Be ratio vis-à-vis fi ring pattern must be used to design the blast rounds. The results have been derived on the digital image analysis based fragment size characterization, excavator performance and evaluation of powder factor values on blasted muck piles. Skewed V- type fi ring yielded the best results in comparison to straight v-type and normally practiced diagonal fi ring pattern on the moderately strong sandstone benches, whereas, the existing diagonal fi ring pattern appears to be satisfactory on weak (weathered and gritty) sandstone benches. The presence of geological anomalies has also been investigated.

Jan 1, 2008

The underwater explosions have been used for several decades for the determination of energy content of explosives. This test method is the only one by which shock, fly rock and total energy can be measured separately. It enables to develop the energy content of explosives for different purposes; the military high explosives should contain more shock energy whereas the fly rock energy is very important feature for the blasting explosives. The purpose of this study was to establish a test place for the underwater experiments in an old water filled open pit, to estimate the repeatability of the energy measurements, to calculate the standard deviations and to compare the total energy content of commercial explosives to the theoretical values calculated by the thermo dynamical program. The test method seems to work quite well especially for the homogeneous explosives. The difference between the energy content of theoretically calculated and measured values for the homogeneous emulsion explosives was about -3% and for the dynamite about -5%. The energy difference for the unhomogeneous ANFO was detected to be -19%. The diameter of the charge was 15 cm and it was obviously too small for ANFO to detonate ideally. On the basis of the test results this test method seems to fit best for the cap sensitive, completely homogeneous, spherical charges whose masses are big enough and which are initiated from the centre of the charge. The underwater explosions as a test method is the only one which can separate shock, bubble and total energies from each other and therefore makes it possible to develop the properties of explosives for different purposes which is very important feature of this method.

Jan 1, 2005

By AJ Rorke

Blasting trials using Daveytronic Electronic Delay Detonator systems (EDD’s) were conducted at the Alpha Ferro Quany (Pretoria) and the Eikeboom Colliery near Witbank in November 1999. The objectives of the trials were to determine the influence of accurate hole firing on rock fragmentation, blast-induced vibration and blast throw. This paper provides an outline of the trials and an analysis of the results. The results were compared with a normal shock tube initiation system. Fragmentation was measured using video-imaging techniques at the hard rock Ferro Quarry for one conventional shock tube blast and two EDD blasts. No significant difference was measured in the fragmentation between the shock tube blast and the two electronic detonator blasts. Joint planes mostly defme the fragments at Ferro Quarry. The fragment sizing was therefore controlled mainly by the rock structure and the blast timing appeared to have no influence. Vibration measurements made at Ferro Quarry indicate that electronic detonators have a marked effect on vibration frequencies compared to shock tube systems. The more accurate detonators resulted in a narrower f+equency band at lower amplitude with similar timing. By modifying the blast timing, the dominant frequencies were changed. The electronic detonators had a significant positive influence, therefore on blast vibration and its control. The timing scatter measured from the shock tube blast was considerable, with measured inhole detonator scatter at 48 ms over a sample of 19 units. Surface delay periods less than 42 ms would therefore not be able to provide effective sequential firing. The scatter of the Daveytronic units was below the 2 ms resolution of the high-speed camera used to film the blasts. Reliable sequential firing, even at very short delay intervals was considered the main reason for notable improved throw in an overburden blast at Eikeboom Colliery. Blast throw was improved by 25% for the test blast.

Jan 1, 2000

By John Floyd, Maria Rocha, Benjamin Cebrian

Wall control blasting is needed in most metal mining operations in terms of increasing mineral reserves and assuring the safety of the operation. This type of blasting has the goal to achieve a clean, stable rock wall in the shortest distance from a well fragmented, easy to excavate, blasted rock mass. This can be done with a variety of blasting techniques, all of which decrease the explosive energy towards the final wall. Each technique needs to suit the geology: modified production blasting, buffer blasting, pre-split and line drilling of empty holes. Pre-split is the most expensive technique, and allows final steeper bench face angles while modified production blasting is the least expensive but needs wider berms.

Jan 1, 2018

By Norm Disley, Kingsley Hortin, Gertjan Bekkers

As part of the expansion of the Kidd Creek Mine to 2,682 meters (8800 feet) below surface, two largediameter 3000kW (4000HP) booster fans were installed at the 6000 level. Shortly after commissioning the fans, significant damage to the fan bearings were observed, forcing several shutdowns for repairs, which were very disruptive to the mine’s production process.

Jan 1, 2008