Search Documents

By Miguel Becerra, Daniel Jordán, Jorge Soto, Luis Torres

"Most SAG grinding operations currently use ball sizes between 5.5 and 6 inch maximum size. However, in most cases the use of this ball sizes hasn’t been justified by a phenomenological analysis of the real effect on the grinding process, but rather by trial and error. The analysis of the influence of ball sizes in SAG grinding hasn’t been developed in detail by considering the effect on process parameters inside the mill, grinding efficiency or internal classification. Historically a conventional grinding reference has been made on the empirical procedure developed by Azzaroni (1980). Further to Azzaroni’s methodology, Sepulveda (Sepúlveda, 2007) developed the SPEC methodology, incorporating the ball size effect on the grinding efficiency parameters using a population balance model included on Molycop tools spreadsheets.This paper demonstrates a detailed analysis at pilot scale of the ball size employed in SAG grinding and scaling that exists between the different levels. This analysis includes assessing the effect of balls sizes on parameters associated with grinding efficiency and its effect on the total fill level, product size distribution and specific energy consumption, among others. In a complementary way it develops a technical - economical evaluation from industrial data comparing two different ball sizes and its effect on the grinding process analysed integrally."

Jan 1, 2014

By K. H. Luo, J. Y. Liu

An experimental study on interparticle breakage of three iron ores was carried out by compressive stressing of particle-bed in a piston-die device. The feeds to the particle-bed stressing were five narrow size fractions in the size range of 0.2~3.2 mm respectively and a wide size fraction of 0/4.0 mm. The pressures applied were in the range between 30 and 360 MPa. The results show that the energy absorption of the particle bed increases linearly with the pressure; the increase of the product fineness with the pressure declines as the pressure goes up; and the product size distributions resulting from interparticle breakage of different narrow size fractions have no self-similarity. Using data obtained from the piston-die compressive stressing test, the suitability of a previously-developed material-characterization model for interparticle breakage was verified for these ores. It is shown that the particle-bed compression test conducted with piston-die device in lab-scale may provide a cost-effective way of studying and modelling size-reduction of ore materials by interparticle breakage.

Jan 1, 2014

By Shugang Hu

According to XRD, DTA and SEM detections, the hydration products of blast furnace slag (BFS) based cementing material SL, SLG. were studied in different age periods. The XRD analysis of cementing material SL hydration products showed that the composition of hydration products were mainly amorphous substances, few crystalline substances. Characteristic peak of ettringite hadn?t been found in the spectral line of DTA, and it hadn?t been found in the figures of SEM, either, which was accordant with the conclusion that the cementing performance of SL mainly coming from gel of hydrated calcium silicate (CSH) and hydrated calcium aluminate. However, the main hydration products of SLG are Aft, CSH, and AFm, which are similar to Portland cement. All results suggest that BFS is a suitable base material for cementation. Keywords: blast furnace slag, backfilling cementing material, hydration products, cementing performance

Sep 1, 2012

By V. Runkana, N. K. V. Nadimpalli, S. Sahu

"IsaMill™ has been in operation in the recent past for fine grinding of low grade ores to extract non-ferrous minerals. IsaMill™, typically, consists of a series of uniformly spaced identical disks mounted on a rotating shaft which is encased in an outer shell. The mill offers high energy efficiency for fine grinding and an inherent scalability. But, it encounters certain operational challenges such as non-uniform distribution of grinding media coupled with high wear rate of the disks and solid walls of the mill at specific locations—which adversely affect the mill performance. To circumvent these operational challenges, design modification of the disks through heuristics, by introducing a reduced diameter disk (RDD) at specific locations, is a common practice in industry. But there is no systematic scientific study in this regard. In the current work, we developed a discrete element method (DEM) based model and simulated for the IsaMill™ operation to study the effect of RDD on the efficiency of the mill and wear rate of the solid walls and disks. Since the first set of disks experience the high wear rate due to the high loading of the charge, the RDD was introduced at the first two disks. The simulations were performed at different diameters of the RDDs and at different media loadings. The performance of the mill was analyzed based on the power consumption, the wear rate on disks and the distribution of media particles inside the mill. Besides, the performance variables such as mean velocity of media particles and total impact energy provided useful insights into the milling operation. It was observed that the reduction in disk diameter yields lower wear rate of the disks at the cost of decrease in power draw at a constant high media loading. Whereas, when the media loading was decreased, the amount of wear and power drawn was comparable for both the most reduced and least reduced disk diameters. Therefore, there is an optimum choice of RDD for a given mill loading to maximize the mill performance while reducing the wear rate of the disks."

Jan 1, 2018

By W. Fander, Zhonghan Zhang, T. Choo, J. Enraght-Moony

"This paper describes the mineralogical and metallurgical procedures used to determine the recovery and concentrate grade of heavy oxide minerals occurring in lode deposits. The data produced also provide vital information to the processing engineers, which allows them to develop the most suitable flow sheet for that particular heavy mineral, here called an Economic Oxide Mineral (EOM). It demonstrates how results are interpreted to ensure that the proper process is used at each treatment stage to optimise recovery and to produce the most suitable concentrate at that point. Reference is made to some of the current equipment and techniques that can be used to process EOMs. The paper shows that when assessing the economic potential of a new ore body, or existing ore treatment plant, ore characterisation (OC) is necessary. This is especially true for EOMs such as cassiterite (SnO2), wolframite ((Fe, Mn, WO4,) pyrochlore ((Na,Ca)2Nb2O6(OH,F)), and tantalite (MnTa2O6) where often what seem to be small changes in ore types can have major effects on recovery and concentrate grade. Due to advances in flotation technology scheelite (CaWO4) in some deposits can be less vulnerable to OC variability than other EOM’s. Thorough mineralogical examination is shown to be the fundamental basis of correctly undertaking OC. This is because mineralogical analysis identifies each of the steps required to ensure that all ore types and zones are recognised, and differences explained, and shows the benefit in using reference samples to compare differences in the ores. The OC methods used for EOMs containing metals such as tantalum, tin, tungsten and niobium are similar; if two or more of these EOMs occur in one deposit as separate minerals, then OC will show when and how these minerals should be separated. The OC techniques described for EOMs can also be tailored for other heavy minerals, precious metals and graphite."

Jan 1, 2014

By P. K. Fedotov

Annually at least 5% percent of world power consumption is involved in the process of ore dressing while ore processing technology. Such rate of energy consumption demonstrates the importance of a given process study in the human life-sustaining activity. Examining of interparticle destruction being under external stress pressure in ore responses this problem solution at the greatest degree. The technology of destruction in the roll press is of great interest. The use of the given equipment allows to save a significant amount of energy by means of the built-in ore destruction mechanism. Examination of stress-strain fields which determine the level of interparticle destruction between the rolls in the ore layer enables to specify both level of ore destruction and power consumption. The mathematical computer modeling for the deformable environment use based on the finite-element method (FEM) allows to carry out the given research. We use FEM solution for elastic contact problem for the most complete study of power consumption employed in ore and interparticle destruction. This problem solution allows also to examine energy consumption expenses spent for ore crushing in the roll press. Also we have identified the mechanism of ore in a layer of the particles under pressure roller press. It is established that high level of performance and reduction of energy consumption in interparticle destruction of ore in the layer due to the appearance of the gradient of normal stresses in contact of particles of mineral raw materials. The algorithm has been developed determining crushing product particle size distribution of fractured particles in the layer, using the Bond’s theory of crushing. The use of our FEM model reduces the time of equipment selection for new plant and at the design stage to reduce the risks of errors in the choice of roller presses.

Jan 1, 2018

By G. Sedelnikova

This paper is aimed to elucidate the problem of copper losses in pyrometallurgical slag. Currently, flotation is used to recover copper from the slag and return the metal into the pyrometallurgical process, but the percentage of recovery frequently remains unacceptable. The process of copper leaching from the slag flotation tailings using biologically regenerated ferric sulfate is considered here as an approach to the issue. A sample of the slag flotation tailings containing 0.67% Cu and 4.99% Zn was supplied by the Urals Mining and Metallurgical Company (UGMK, Russia). The Cu and Zn speciation analysis of the sample demonstrated that Cu occurred as 58.1% oxide, 15.4% native Cu, and 18.1% secondary sulfides whereas chalcopyrite proportion was as low as 8.4%. Prevailing Zn species were refractory (58.9% Zn ferrite), and zinc oxide and silicate species made just 37.2% of the total metal content. The silicate generated silica gel that strongly hampered filtration. As demonstrated, Cu recovery is a possibility, which is apparently not the case with Zn. In this work, the stirred tank bioreactor acid leaching employing bacterial Fe3+ sulfate solutions was studied, with ferric sulfate being a product of Fe2+ biological oxidation and not the chemical reactant adding of Fe3+ sulfate. Acidithiobacillus, Sulfobacillus, and Leptospirillum bacilli were employed in Fe2+ biooxidation. Temperature, pH, Eh, S:L ratio, leaching time, and Fe3+ concentration in the source leachate as the process controls were considered. As demonstrated, the process employing biologically regenerated ferric sulfate proved to be more efficient than conventional chemical leaching. Under the optimum conditions, the proportion of Cu extracted into leachate during 2 hours was 79.1%, and that of Zn 27.2%. Precipitation of high-grade Cu sulfide served to extract the metals from the leachate, and Cu extraction was 99.7%. All in all, 23.2% Cu, 0.03% Zn, and 0.02% Fe was returned into the pyrometallurgical process. Keywords: slag flotation tailings, copper leaching

Sep 1, 2012

By T. N. Alexandrova

Results of mineralogical-technological research of carbonaceous rocks of Kimkansky precious metal occurrence are presented, on their basis new typemorphic natural and technological microelement associations were revealed using mathematical statistics methods. Keywords: carbonaceous rocks, processing, microelements, flotation, statistical criteria

Sep 1, 2012

By H. Palza, C. Ihle, S. Contreras

"Processing of minerals, particularly treatment of tailings, has been increasingly challenged by the presence of clays in the feed of thickeners. This occurrence is expected to become increasingly important given the nature of ore deposits currently being exploited and those that have been recently discovered. In sedimentation operations (solid-liquid separation), industrial flocculants often fail to coagulate clay-containing fines, generating supernatants with high levels of turbidity, thus implying operational problems. Recently, it has been reported that graphene oxide (GO), a graphite derivative with high oxygen-containing groups, could enhance the flocculation of clay systems, due to the interaction between clays and GO functional groups. In the present work, we investigated the effect of doping industrial flocculants (commercial polyacrylamide) with GO on the floculation of kaolinite suspensions in a solid-liquid separation stage. Separation performance was evaluated by studying flocculation kinetics using a focused beam reflectance measurement (FBRM) instrument, in a set of batch tests. A statistical analysis of the flocculation kinetics and floc population distribution was further carried out. Our results suggest the existence of a synergistic effect between the studied flocculants and GO. This effect is observed as a decrease of clay fine contents in the supernatant, thus improving solid-liquid separation eficiency for high clay containing tailings. INTRODUCTION Copper, given its mechanical, physical and chemical characteristics, is a critical material for the progress of society and so has been from early stages of mankind. Demand for this metal has increased due to the growth of cities and the technological explosion, leading to increase current mining production and reinforce the efforts in exploration for new deposits (Elshkaki et al. 2016). As copper-rich deposits are being depleted, it has been necessary to develop proper technology to mine deposits of lower grades and more complex mineralogies, keeping in mind that the economic window that allows the exploitation of them is reduced by the increase on operating costs (Crowson 2012 and Northey et al. 2014). High clay bearing minerals are found in many of those low-grade copper deposits, and they induce problems in all stages of the mineral processing route (Taner and Onen 2016). Particularly, in the solid-liquid separation stage, the flocculation process fails to remove the clay fraction from suspension and it leads to operational issues such as filter damage, overconsumption of reagents and the need to add an extra clarifying step for the recovered process water. Those problematics pose an interesting challenge."

Jan 1, 2018

By A. Güney

Currently, recycling technologies use relatively homogeneous plastics because hand-sorting waste feed is too expensive. Many promising technologies for separating mixed thermoplastics are being investigated, but they are still uneconomical and unreliable. Burning plastics for recycling is not used because of poisonous gases released when their burning. PET and PVC cannot be separated using conventional gravity separation techniques because their specific gravities overlap; PET density changes from 1.33 g/cc to 1.37 g/cc and PVC density is between 1.32 g/cc and 1.37 g/cc. For this reason, plastic recycling needs new techniques. Among these techniques froth flotation, also used in mineral processing, can be useful for its cost and simplicity. In this method, a plastic is selected from mixture, tried to regain its natural property, hydrophobicity. In this study the experiments were applied by using plasticizer reagents to make the selected plastics hydrophobic and us-ing NaOH to render the other hydrophilic. Post-consumed PET and PVC are evaluated by concerning the effects of selected parameters (particle size, concentration of plasticizer reagent, amount of NaOH, conditioning time and the effect of conditioning temperature). At the end of the experiments, optimum parameters for selective flotation of PET from PVC was found as particle size of -4.76 + 3.36 mm, NaOH amount of 30 kg/t, conditioning temperature of 75°C, conditioning time of 30 minutes, reagent amount of 300 mg/L. Consequently, PET was re-covered with 99.7% purity and 57% efficiency.

Jan 1, 2014

By Erico Tabosa, Kym Runge, Peter Holtham

"The distribution of turbulence in an industrial scale mechanical flotation cell and its effect on flotation kinetics was studied using a fully instrumented 3m³ cell. The cell was operated at a copper concentrator in Australia with different combinations of airflow rates, impeller speeds and sizes and cell aspect ratio providing a wide range of hydrodynamic conditions. An analysis of the overall flotation cell performance showed that the overall copper recoveries were very similar for the conditions tested. However, by decoupling pulp effects from froth effects it was possible to evaluate whether the changes made affected the pulp zone and/or froth zone responses. The analysis showed that the overall recovery has the potential to be up to 7% higher, if not limited by froth recovery. The cell hydrodynamics were characterised by the overall energy dissipation rate and, to understand the distribution of turbulence within the cell, localised measurements were made using a piezoelectric vibration sensor. By comparing the metallurgical performance of the cell with the different hydrodynamic conditions it was found that the collection zone flotation rate constant was not directly related to overall energy dissipation, as is commonly observed at laboratory scale, where energy is usually only changed by varying impeller speed. In this study, energy dissipation rate was varied using not only impeller speed, but also the size of the impeller and the cell aspect ratio. In these circumstances, the best correlation was found to be between the collection zone flotation rate constant and the distribution of turbulence, i.e. the size of the turbulent zone."

Jan 1, 2014

By V. Y. Dementyev

Laboratory and pilot-plant testing using a sample of gold-bearing semi-oxidized ore from a Russian deposit followed by a flow sheet and reagent flotation mode development to design a plant was carried out in IRGIREDMET in 2009-2010. According to the developed flow sheet low alkaline flotation conditions are recommended in order to activate the surface of sulfides. The pH lowering from natural (7.5-8.0) to optimal (4.6-4.8) value using sulfuric acid provides for an increase in gold recovery. Before CIL, a final flotation concentrate is pretreated using pressure oxidation. It was found that the use of recycled solutions from pressure liberation in order to create acidic conditions for flotation instead of sulfuric acid during pilot-plant testing is recommended. The flow sheet offers the detoxification of remaining pressure oxidation solutions together with the flotation tailings. The carbonates presented in the tailings significantly reduce the consumption of lime for detoxification and allows for the use of two tailings dams instead of three. The first is used for the tailings of flotation and pressure oxidation recycled solutions, which were detoxified together. The second tailings dam is used for detoxified cyanidation cakes of the flotation concentrate. It was found during pilot-plant testing that flotation under natural and acidic conditions provides for 88.9 percent and 93 percent gold recovery, respectively. 4.1Au percent increase recovery was achieved due to the reduction of gold losses with flotation tailings and better quality of concentrates.

Sep 1, 2012

By M. Karamoozian

Modelling and optimisation of the power draw of large SAG mills are important due to the large power draw which modern mills require (5~10 MW). The cost of grinding is the single biggest cost within the entire process of mineral processing. Traditionally, modelling of the mill power draw has been done using empirical models. Although these models are reliable, they cannot model mills and operating conditions, which are not within the model database boundaries. Also, due to their static nature, the impact of the changing conditions on the power draw, within the mill, cannot be deter-mined using such models. Despite advances in computing power, on-line modelling of large plant scale mills could be a time consuming task. On the other hand, using on-line parameters for model-ling, result in more reliable control of SAG mill without performing any more costly tests. In this paper, SAG mill power draw is modelled using neural network approach. Six inputs, namely: solid percent, two bearing pressures, noise, recycle and feed rate were used to model the power draw. The produced model shows an acceptable correlation coefficient, R2 =0.9623.

Jan 1, 2014

By S. Leroy

Grinding is the most energy consuming step in mineral processing, however, it is still poorly understood and its efficiency is difficult to monitor. Mill performances are traditionally measured at the mill discharge, on the basis of a mass percentage passing a certain sieve. This approach does not reflect what happens to the fines through milling. On another hand, if many macroscopic parameters, such as the percent solids of the pulp, its viscosity, or its mean residence time in the mill are known to be related to grinding efficiency, the link between these parameters and particle size distribution (PSD) is still unclear. Here, a methodology is established to understand the effect of ball mill operating conditions on particle size and shape distribution in the grinding process. The study focuses on the particular case of an Upper Group 2 (UG-2) platinum ore concentrator. Due to the very low grade of sulphide and PGM (Platinum group metals) in UG-2, grinding mechanisms are entirely control by gangue minerals. These two minerals have contrasted properties and PGM content and these properties immediately affect the entire recovery process. So, the grinding of both gangue minerals is studied on a size by size basis. At particle scale, three parameters are addressed: particle size, particle composition and particle shape. The specific behavior of chromite and silicate grains is demonstrated. As a conclusion, this study gives some clues to operate ball mills in a more efficient manner regarding chromite issue in the processing of UG-2. Keywords: ball milling control, UG-2, chromite, fine particle, particle shape, segregation

Sep 1, 2012

By Z. M. Wang

A large scale a polymetallic mine in north China is a refractory ore containing many useful com-ponents: W, Mo, Cu and Fe. Mineralogical investigation shows that the deposit is a quite complex one due to fine disseminated size and unevenly distribution of valuable, intergroth of sulphide and tungsten minerals, concurrence of scheelite and calcium minerals. Based on ore characteristic, a flowsheet is used by the floatation processing of sulfide minerals superior to scheelite. Bulk sulphide flotation is used in sulphides. Mo and Cu are floated in sequence after sulphides regrinded. Tungsten mineral is floated using combined depressant that is an effective depressant to gangue, and can improve the grade of rough tungsten concentrate. Compound depressant has high effective in removal of collector in gangue and sulphide, and tungsten is activated also. High quality of tungsten concentrate is obtained at satisfactory recovery. The test production obtains Mo concentrate with grade of 48.16%, recovery of 81.43%; W concentrate with grade of 66.47%, recovery of 78.19%; Cu concentrate with grade of 23.14%, recovery of 56.6%; Fe concentrate with grade of 67.33%. The valuable metals are recovered comprehensively and well techno-economic index is obtained. The mine enterprise profit is increased greatly.

Jan 1, 2014

By Ata Akcil, Z. B. Karshigina, Ye. G. Bochevskaya, E. A. Sargelova, Z. S. Abisheva

Phosphorus slag is one of the most large-tonnage of yellow phosphorus production waste, which for decades stored in the slag disposal, by polluting the environment and creating environmental problems in the regions. Phosphorus slags from the processing of Karatau phosphorites are a very promising source of raw materials not only for silicon compounds but also rare earth metals (REM). Among the REM, yttrium, neodymium, europium and lutetium predominate, which are relevant to high-tech industries. The report presents technological scheme of complex processing of slags of phosphoric production with obtaining of REM concentrate and precipitated silicon dioxide ("white soot"). The regime parameters of the main operations of the technology are determined: I stage- leaching of slag with nitric acid solution; extraction of the REM-containing solution with tributyl phosphate and stripping of the REM with water; settling of solution of salts of oxalic acid, calcining the precipitate to obtain a concentrate S REM oxides and II stage of leaching silicon cake to obtain "white soot". Recovery of S REM from slags of phosphoric production on various redistribution has made, %: leaching – 95.0; extraction - 90.2; extraction on the average ~ 93.2; the production of a concentrate of REM oxide is 93.9. A concentrate containing 17.3 % of REM oxides was obtained. According to X-ray analysis it contains the following phases: calcium oxide, portlandite2, gadolinium oxide and yttrium, gadolinium oxide, gadolinium oxide and cerium, neodymium oxide, neodymium oxide and cerium. Thus, the concentrate can serve as a raw material for the production of individual rare-earth metals like gadolinium, cerium, yttrium and neodymium. After performing the II stage of leaching siliceous cake with nitric acid the samples of "white soot" were obtained. Its chemical composition corresponds to the state standard and has a specific surface area equal to 180 - 200 m2/g. The technology has been tested in a large-scale laboratory scale and will solve the problem of complex processing of phosphorus raw materials and import substitution in Kazakhstan. The end-to-end recovery of S REM oxides and silicon into concentrate and product from their initial content in slags is ~ 75.0 and 98.0 %, respectively.

Jan 1, 2018

By Y. Posedko Eugene, S. S. Gudkov, Yu. E. Emelyanov, A. V. Bogorodsky, A. V. Boldyrev, S. V. Balikov

"The article presents the results of precious metals leaching using halogen solvents and their precipitation on a sorbent in the process of pressure oxidation. A technology of pressure oxidation – carbon-in-leach treatment (POX-CIL) of refractory sulphide gold-bearing flotation concentrates with the addition of a halogen solvent and a sorbent was developed based on the laboratory studies and pilot plant tests. The technology involves the following steps: oxidation of a flotation concentrate; precious metals dissolution and recovery on a sorbent; precious metals elution; electrolysis of eluates; smelting of cathode precipitates with producing Dore beads. This approach ensures oxidation at least 98% of sulphides and gold of more than 95%. The POX-CIL process have the following patents: a patent of the Eurasian Patent Organization No.017438 “A method of processing materials containing precious metals and sulphides” and a patent of the Russian Federation No.2625146 “A method of precious metals recovery from refractory sulphide gold-bearing materials”.INTRODUCTION Gold-bearing ores are classified as readily amenable to cyanidation, or non-refractory, and not readily amenable to cyanidation, or refractory [1]. Special attention should be given to the three most common technological types of gold-bearing ore materials, according to the Irgiredmet’s classification: pyrite-arsenopyrite ores with finely disseminated gold locked in sulphides (physical depression of gold in cyanidation process); cupriferous gold-bearing ores, when cyanidation comes along with chemical depression of gold by mineral compounds (cyanisides); carbonaceous ores showing higher sorption activity to precious metals dissolved in cyanide. Direct cyanidation of refractory sulphide gold-bearing materials does not provide high recovery of precious metals. There are the following methods of refractory gold-bearing ores and concentrates preparation to subsequent gold recovery: roasting, fine grinding, bacterial and pressure oxidation (POX) [2]. Existing POX-cyanidation flowsheets involve high costs due to a large amount of process operations and using expensive and environmentally hazardous sodium cyanide."

Jan 1, 2018

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama

Results of flotation process combined with atmospheric leaching and high pressure leaching for recovery of copper from low-grade silicate-copper ore have been presented in this study. The low-grade copper ore contains a small amount of copper (0.42 mass %), iron (4.6 mass %), and silicon (38.3 mass%) and among many other metals (Al, Ca, K, Mg, Na, Ti and S). The main mineralogical constituents of the copper ore are calcium aluminosilicate (Ca(Al2Si2O8), amesite (Mg2Al2SiO5(OH)4) and gypsum (CaSO4×H2O), and quartz (SiO2) as resulted from the alteration of an igneous rock. This study has shown that about 92 % of copper can be recovered with a maximum copper grade of 4.2 mass% in a froth after 15 minutes of flotation at pH 8.5 when used potassium amyl xanthate as a collector, MIBC and Dow-froth 250 as frothers and calcium hydroxide as a pH adjuster. The images of bubbles in the cell during flotation process were recorded using a high-speed camera. The froth concentrate with average copper grade of 2.0 mass% was further processed by atmospheric leaching with a solution of sulphuric acid and hydrochloric acid, respectively and high pressure leaching with sulphuric acid solution. As a result, leaching rate of copper reached about 60 % in an atmospheric leaching with sulphuric and hydrochloric acid respectively, whereas the rate can reach more than 70 % by autoclave leaching at high pressure under the controlled condition. A process to recover of copper from its low-grade ore can be developed by optimization of flotation combined with acid leaching.

Jan 1, 2014

By N. Nikolaeva, A. Romashev, T. Aleksandrova

Energetic characteristics identify energy consumption for destruction of prills and kinetic characteristics rate formation of finished size grade in the course of destruction and identify crushing and grinding equipment capacity. And if screen sizing or classification processes are applied in the cycle of ore preparation, then the use of characteristics of separation to size – separating characteristics – is required for theoretical description. Separating characteristics have a lower profile for ore preparation but, nevertheless, they have to be taken into account especially for balance and design calculations of crushing and grinding circuits. In most cases there are impregnations of minerals which vary widely in energy consumption and destruction kinetics and thus polyminerality must be considered as one of priority factor. Raw materials which passed through crushing and grinding processes can be assessed numerically by functions of fractional composition of two types: differential distribution function y ( €) and assay function B( c ) . A set of experiments on grinding of crushed raw materials at different time (up to various sizes) was conducted to analyze effect of grinding size of carbonaceous overburden on function y € and B ( c) as well as to justify the possibility of preconcentration of raw materials at the stage of ore preparation. Analysis of metals distribution per size grades showed that metals are concentrated in size grades of less than 0.315 mm (which is equivalent of cut point for this type of raw material), however, there is no overgrinding and oversludging of material, and enriched product for its further processing can be excluded with the help of classification. The stage of size segregation was tested as a method of preconcentration of raw materials for optimization of ore preparation and further separation.

Jan 1, 2018

By A. Oleynik

The paper presents the modeling and simulation experience in field of research into the mineral row material separation. Features of the subject domain generate a need of different approaches using for modeling and simulation. The general scheme of separation modeling process and some examples of developed simulators are presented. Due to different features and standards of knowledge, different formal models should be used to describe and analyze separation processes in the frame of general scheme. The main types of simulators are modeling tools based on statistical, analytical or expert (logical) methods. Advantages and disadvantages of each method above are mentioned in the paper. Based on the studies in the field considered, an aggregated mathematical model of a separation process has been generated. The aggregated model is presented by two combined equations. The actual apparatus model is formed by substitution of the particular functional expressions of the forces acting in the apparatus into the aggregated model. The developed simulation tools are based on integration of limited experimental data and on ex-pert knowledge available on separation processes. Simulation does not allow producing an optimal, in terms of mathematics, solution. But it gives an opportunity to produce and compare quite adequate solution variants in real time. The results obtained are the theoretical and methodological base for integrated information technologies to support studies in the field of mineral processing.

Jan 1, 2014