Search Documents

By L. A. Vaisberg, E. V. Shishkin, S. V. Kazakov

"This research is targeted at finding solution to the problem of reduction of specific energy consumption during disintegration of solid materials with the help of machines, operating in a quasiresonant mode. The objective of the research is the development of an energy-saving method of disintegration of supestrong rock and by-products on the basis of vibrational units with two movable crushing elements, operating in a rigorous synchronous-antiphase mode without stringent kinematic links. In the course of investigations a mathematical analysis of the dynamics of vibrational units was performed to determine required mechanical parameters, allowing for adjustment of the machine actuating elements to high-frequency synchronous-antiphase oscillations in the quasiresonant frequency range. As a result of performed pilot tests, the reliability of desktop studies was confirmed and the dependency of process parameters on the machine regulated parameters in the quasiresonant frequency range was identified. The analysis of obtained data showed that during machine operation with cone-shaped crushing elements in the quasiresonant frequency range, the yield of the high-quality finished product (WFA grits of -3+1 mm grain size class) in one pass reaches 35%, whereas the form of the particles corresponds to the grain form with sharp edge. The quasiresonant operation mode of the vibrational unit with two freely suspended crushing elements (without stringent kinematic links) provided substantial reduction of energy intensity during crushing down to 0.16 kWh/t, which shows reduction of power consumption for crushing by more than 15% compared to conventional equipment.INTRODUCTION The most common and energy-consuming processes in the mining industry are the crushing and grinding of various solid materials. Such large energy costs are due to the fact that the capabilities of the existing crushing and grinding machines are based on traditional methods of destruction, and are limited by their kinematic features, which do not allow to reduce the energy intensity of processes, to lower the irreversible loss of useful components, to improve the quality of marketable products. In connection with the foregoing, the task of energy costs reducing for disintegration is one of the most important issues in the enrichment of both minerals and processing of man-made raw materials. The solution of this problem is possible only through the creation of a fundamentally new highly efficient technique and technology for processing raw materials [1, 2]. It seems that the greatest prospects in this respect are the vibration methods of disintegration, in particular, the vibratory cone crusher based on a two-mass system without rigid kinematic connections between the crushing bodies, with vertical vibrations of the working bodies. In this machine, the principle of rational material destruction is realized – crushing without re-grinding [3-5]."

Jan 1, 2018

By Kyle P. Flynn, Frank J. Hrach, James D. Bittner

ST Equipment & Technology, LLC (STET) has developed a processing system based on tribo-electrostatic belt separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. In contrast to other electrostatic separation processes that are typically limited to particles greater than 75µm in size, the triboelectric belt separator is ideally suited for separation of very fine (<1µm) to moderately coarse (300µm) particles with very high throughput. The high efficiency multi-stage separation through internal charging/recharging and recycle results in far superior separations that can be achieved with a conventional single-stage free-fall tribo-electrostatic separator. The triboelectric belt separator technology has been used to separate a wide range of materials including mixtures of glassy aluminosilicates/carbon, calcite/quartz, talc/magnesite, and barite/quartz. An economic comparison of using the tribo-electrostatic belt separation versus conventional flotation for barite / quartz separation illustrates the advantages of dry processing for minerals.

Jan 1, 2014

By I. Zimbovski, T. Ivanova, E. Chanturiya

"The mechanism of selective action of new reagent-collector AMD of phenylpyrazolone class with sulphide minerals of copper-zinc ores was theoretically and experimentally investigated. The validation was carried out using spectrophotometry, Fourier-transformed spectroscopy, laser scanning microscopy, analytical scanning electronic microscopy and flotation. The reagent AMD in alkaline medium on chalcopyrite and sphalerite surfaces is chemically sorbed, forming strong hydrophobic complexes with copper and zinc. On the pyrite surface, AMD acidifies ferric iron ions with formation of hydrophilic oxidates. The selectivity of collector AMD with separation of sphalerite and pyrite in alkaline condition (??=10) is confirmed by flotation experiments. With AMD, the obtained recovery of sphalerite was 34.4 % at extraction of pyrite of 3 and 6 %. The low recovery of sphalerite is caused by weak collective ability of the reagent. The use of copper sulfate increases the flotability of sphalerite up to 82.0 % at extraction of pyrite of 5 and 2 %. It has been experimentally determined that during the flotation of sphalerite and pyrite by AMD reagent with addition of butyl potassium xanthate, and in the presence of copper sulfate and regulator of formation of ammonium thiocyanate complexes, the recovery of sphalerite is increased to 91 %, while the recovery of pyrite is decreased to 3.8 %. The chalcopyrite is floated actively (90 % recovery). The results of all theoretical research and experiments were confirmed by flotation tests on ores and products of dressing in industrial conditions."

Jan 1, 2014

By S. P. Nagaeva, O. U. Poperechnikova, A. V. Kuptcova

"In case of free gold presence in ore, there is always problem of a choice between the gravity-flotation and gravity separation flowsheets. Study of morphology of gold being extracted by different methods allows to find the most efficient solution. One of the latest methods of gold concentration for wide range of grain size (-0.8+0 mm) is a flash flotation. The paper presents comparative testing results of flash and centrifugal separation.The goal of the studies was to determine process and flotation parameters of flash flotation. In case valued minerals are soft if compared to host rock, such minerals tend to concentrate into circulating load of grinding circuit. Thus, valued minerals can be overground, and in turn, will result in low extraction in flotation circuit. Integration of flash flotation operation into process flowsheet has been evaluated. Flash flotation operation can be successfully used not only for gold but also copper, lead, nickel and silver minerals.With low-sulphide ores being a case study under laboratory conditions, various flotation (impeller rotational speed, air flowrate) and process (pulp density, collector consumption, frother consumption, time of flotation) parameters were studied in view of its impact on gold flash flotation. Experiments were carried out under laboratory conditions using special pneumatic mechanical flotation machines.INTRODUCTIONGravity separation is used for extraction of coarse gold before cyanidation and before flotation of polymetallic ores to increase gold total recovery into gravity copper and lead concentrates.Benefit of the flash flotation is efficient recovery of coarse gold carrier particles (sulphides) thus preventing its regrinding and, as a result, low recovery. Furthermore, combination of flash and conventional flotation results in final tailings that do not require further cyanidation.Combined gravity-flotation flowsheets are designed for concentration of ores containing gold within thewide range of grain sizes (see Table 1)."

Jan 1, 2018

By A. J. Lynch, L. Ergun, M. Oner

"A research program on modelling cement grinding circuits has been in operation at Hacettepe University, Ankara, for four years. It has concentrated so far on tube mill and air separator grinding circuits for cement clinker, with emphasis on plant sampling surveys, including axial sampling inside the tube mills. The data used for model development have come from 33 surveys in 9 plants.The operating conditions have been:- mill sizes - 3.2 to 4.8 metres diameter and 8.5 to 15 metres long,- mill feed rates - 46 to 158 tonnes per hour,- air flow through mills - 25000 to 125000 cubic metres per hour,- cement clinker work indexes - 10.3 to 18,- separator sizes - 2. to 3.1 metres diameter,- separator feed rates - 132 to 689 tonnes per hour,- separator speeds - 12.3 to 21 metres per second.The ball mill model is Whiten’s perfect mixing model and the separator model is the Tromp curve with a fish-hook. This paper emphasises the importance of calculating the breakage rates and the discharge functions with three case studies at five different circuits which were selected for discussion because they show how particular features of circuit operation can be included in the general models. Size distribution graphs are used to illustrate every aspect of the discussion"

Jan 1, 2003

By Gabriel Barrios, Juan Pérez-Prim, Marcelo Tavares

"The application of High Pressure grinding Rolls (HPGR) has been growing in the mining industry for the last 10 to 15 years. The major benefits generally supporting this trend are better energy efficiency, improved grinding capacity, less sensitivity to ore grindability variations and higher metal recovery in downstream processes such as heap leaching and flotation. The HPGR machine comprises a pair of counter-rotating rolls mounted in a sturdy frame. One roll is fixed in the frame, while the other is allowed to float on rails and is positioned using pneumohydraulic springs. The feed material is introduced in the gap between the rolls and is crushed by the mechanism of interparticle breakage. Comminution performance is largely determined by the pressure exerted on the bed of particles by the floating roll hydraulic system. The operating bed pressure depends on the hydraulic system start-up parameters and the loading response of the feed material. The work describes how the coupling of the multi-body dynamic simulation with Discrete Element Method in which particle breakage is described using the particle replacement method, can be effectively used to predict the performance of the HPGR. The model considers important variables as the HPGR rolls geometry and design, the hydraulic spring system start-up parameters and the material loading response, to describe operational key outputs as material throughput, operating gap and roller pressure distribution. The preliminary version of the model has been used to predict the effect of material properties on the operating gap and the load distribution on the surface of the rolls, demonstrating that it can describe qualitatively the HPGR operation, indicating that the model will be a power full tool for the simulation and selection of industrial HPGR units."

Jan 1, 2014

By I. A. Khabarova

The paper presents the results of experimental investigations of the effect by high-power nano-second electromagnetic pulses (HPEMP) on change of surface composition, physical-chemical and flotation properties of pyrrhotite, and search of optimal combination of flotation reactants providing increase of metal extraction from disseminated copper-nickel ores. Preliminary electropulse effect on products before flotation allows to create optimal conditions for flotation separation of pentlandite and pyrrhotite owing to forming the new phases and defects on the surface of sulphides. It was established, that the yield of monomineral fractions of pyrite, pyrrhotite and chalkopyrite increases by 5%~15 %, compared with flotation with one butyl xanthenes (BX), during usage of combination of thionic carbamate (isopropylmethylthionocarbamate (ITC) or isopropylethyl- thionocarbamate (Z-200) with butyl xanthate (BX). Sorption of investigated reactants and strength of their fixing on the surface of minerals are examined; it helped to reveal the cause of rise of floatability of sulphide minerals for the case of combination of reactants. Preliminary high-pulse processing and reactant conditions with usage of combination of thionic carbamate and xanthate have been tested on the sample of disseminated copper-nickel ore from Norilsk region.

Jan 1, 2014

Under the AMIRA P9 project the three-product cyclone-an off-shoot of the conventional hydro-cyclone-that produces three distinct products has been developed. The three-product cyclone shows great promise as a classifier in mineral processing. Industrial and pilot plant trials performed to assess its performance in the classification of the UG2 platinum ore, indicate that the presence of an extra overflow product stream that captures the mid-sized particles, provides improved classification efficiency. To assess the split on component density, samples from the feed and product streams were screened and assays by size for chromite (? = 4.8) and silica (? = 2.65) were obtained. Results from tests performed using this type of hydrocyclone in a number of applications indicates that it can be applied successfully in circuit configurations where the conventional hydrocyc-lone is not suitable. Utilising the three-product cyclone to classify the UG2 platinum ore resulted in an intermediate overflow product stream containing the mid-sized low density silicates and relatively fine high density chromite particles while the finer overflow contained mostly fine silicates and chromite particles. The coarse chromite and silicates reported to the underflow. Due to the increased number of products, the method of using efficiency curves was extended to cater for the increased number of products in the three-product cyclone. Although significant differences in the classification performance of the three-product cyclone were noticed with variations in machine variables a consistent method of assessing the performance was applied. The efficiency curve was adopted and applied and separate efficiency curve properties were obtained for each product stream. The methodology was applied to the component data, and efficiency curve proper-ties for each key component were obtained and compared. This paper discusses the application of the efficiency curve to cyclones producing more than two products and extending the methodology to the different components in the feed.

Jan 1, 2014

By C. Dorfling, P. Albertyn

"Hydrometallurgical recovery of metals from printed circuit board waste typically involves multiple leaching stages; conventionally, base metals dissolution by mineral acids is followed by leaching of gold using cyanide or halide based lixiviants. Alternative lixiviants for gold leaching can reduce the potential hazardous nature of operation. The aim of this study was to investigate the feasibility of using thiosulfate as lixiviant for gold leaching from waste printed circuit boards. Batch leaching tests were performed to investigate the effects of thiosulfate concentration (0.1 – 0.2 M), ammonium concentration (0.2 – 0.4 M), pH (9 – 10.5), solids content (25 – 50 g/L), and copper content of the feed material on the gold leaching behavior. The concentrations of metals in liquid samples were determined by means of inductively coupled plasma atomic emission spectroscopy, and high pressure liquid chromatography was used to evaluate thiosulfate degradation/consumption. The ratio of thiosulfate to ammonia was found to have the most significant effect on the extent of gold leaching, with the best gold extraction observed at a ratio of 0.5 mole thiosulfate per mole ammonia. The lower pH range of 9 – 9.5 generally produced better Au leaching, while low copper extraction during the first stage base metal leaching stages has proven to be detrimental to gold leaching from the residue. Thiosulfate degradation/consumption increased and gold extraction decreased with higher residual copper in the feed. An optimum gold extraction of 78.5 % from base metal leach residue was achieved with 0.2 M thiosulfate, 0.4 M ammonia, and 0.02 M cupric ions at 25°C in the pH range 9 – 9.5.INTRODUCTION Background and Aim The recycling of e-waste is becoming increasingly important as it provides certain economic benefits apart from the obvious environmental benefits. Printed circuit boards (PCBs) are found in most forms of e-waste and contain especially high concentrations of base and precious metals. Hydrometallurgical processes are often considered for the recovery of valuable metals from PCBs; these processes normally implement several leaching stages to selectively recover certain metals."

Jan 1, 2018

By Susanna A. C. Stadler, Chris Aldrich, Jacques J. Eksteen

Slag foaming occurs in several pyrometallurgical processes. These processes include steelmaking in basic oxygen steelmaking furnaces and electric arc furnaces as well as various non-ferrous operations like sulphide smelting/converting and base metal slag cleaning. Although slag foaming in steelmaking processes has been extensively researched, little attention has been given to slag foaming in non-ferrous operations. Slag foaming phenomena are complex because often the system consists of three or more phases. With this in mind, factors previously identified as influencing slag foaming were investigated. These include the slag basicity, physical properties of the slag, namely viscosity, surface tension and density, the formation of particles due to undercooling of the slag and the FexO concentration in the slag. The effect of increasing FexO concentration was found to decrease the foam index due to lower viscosities, but higher surface tension depression appears to have led to increased foam index values at high FexO concentrations. The foaming index decreases with increasing basicity, until precipitation of solids occurs. After this point, the foaming index was found to increase with increasing basicity due to increased solids precipitation. In general, increasing amounts of slag-wettable solids led to higher foam indices, but the precise nature of the effect on slag foaming was dependant on the nature of the solid precipitate.

Jan 1, 2003

By J. D. Miller, C. L. Lin

In general, x-ray computed tomographic (CT) techniques are able to provide 3D images of the internal structure of opaque materials in a nondestructive manner. The unique cone beam geometry allows acquisition of all 2D projections with only one rotation of the sample thus providing for fast data acquisition and better x-ray utilization, as a complete 2-D detector array receives the cone-shaped flux of rays. Thus, an isotropic 3D volume can be reconstructed without the mechanical translation and the stacking of sequential slices as is the case for more conventional CT scanners. In this regard, a state-of-the-art, custom designed xray microtomography facility to provide very detailed 3D spatial analysis of multiphase particles has been installed and is in operation at the University of Utah. The reconstructed 3D tomographic volume allows for an adjustable spatial resolution from 5 to 20 microns for sample dimensions from 10 to 40 mm in diameter, respectively. Utilization of this custom designed cone-beam x-ray microtomography system is discussed. Applications described include: coal washability analysis for the design and operation of coal preparation plants, liberation analysis for evaluation of grinding practice and separation efficiency, mineral exposure analysis for prediction of the ultimate recovery from heap leaching operations, and analysis of the pore structure network of packed particle beds for simulation of flow through such porous structures as encountered in filtration and heap leaching.

Jan 1, 2003

By R. Roufail

In this paper, the effect of different operating parameters of high speed stirred mill on the particle breakage mode is addressed. Morphological features of broken particles is investigated and related to the types of forces generated in the mill using Discrete Element Method (DEM). The stress intensities generated in the mill are varied by changing the agitator speed. The investigated agitator speeds were 1000, 1500, and 2000 revolution per minute (rpm). The minerals considered in this study are hard minerals (quartz) and soft, sulphide minerals (galena). The morphological features examined are roughness, roundness and elongation, which shed light on the mode of breakage during the grinding process. Particles that are rough, less round and elongated would imply that they broke via fracture, along their grain boundaries. On the other hand, the smooth, less elongated particles would mean breakage occurred across the grain, which is abrasion mod. DEM study complemented the understanding of particle breakage mechanism via tracking the types of forces applied on the particles. Normal forces imply compressive loading, which is presumed to impose fracture breakage along the grain boundaries, whereas tangential forces imply abrasion loading. Stirred mill grinding has been regarded as an attrition/abrasion process, whereas, this study showed that about 60% of total particles that are morphologically analyzed for both minerals were rough particles. Such an observation indicates that the fine product, which contain a significant amount of progeny from the coarse fractions are consistently broken via fracture. The morphology results agreed with the DEM findings, which indicated that the agitator speed, mineral type, and residence time would dictate the type and mode of particle breakage. Keywords: DEM, high speed stirred mill

Sep 1, 2012

By Mohammad Noaparast, Hamed Haghi

"In this research work, it was attempted to reduce the iron contents (Fe2O3) in relatively low grade silica sample which was obtained from Shenin silica mine, using magnetic separation. The prepared sample contained 93.75%SiO2, 0.44%Fe2O3, 2.78%Al2O3, and 0.08%TiO2 and the Fe2O3 had to be reduced to less than 0.08%. Mineralogical studies and XRD analysis indicated the presence of Hematite, Pyrite, and Goethite as the major iron impurity phases. Mineralogical studies of polished and thin sections demonstrated that the degree of freedom of silica is more than 80% in -300+212 ?m size fraction. After primary stages including crushing, milling, scrubbing and de-sliming, various methods such as low intensity magnetic separation (LIMS), high gradient magnetic separation (WHGMS) and dry high intensity magnetic separation (DHIMS) were applied to find out that which process would be appropriate for the elimination of iron impurities from this sample. Different experiments were carried out on the product of wet rod mill and scrubber. However the magnetic field intensity of WHGMS was increased down to 2Tesla, and there was not any acceptable result in reduction of Fe2O3 content lower than 0.08%. Thereafter the product of wet rod mill and scrubber were dried and reported to DHIMS. In these experiments, maximum magnetic field intensity was 1.4Tesla. In this case very significant results were achieved, and Fe2O3 content of final product were reduced to less than 0.05% which meets glass manufacturing standards."

Jan 1, 2014

By T. Suzuki

Acid leach liquors from spent lithium-ion batteries employing lithium cobalt dioxide (LiCoO2) as a cathode active material contain valuable metals such as cobalt and lithium, as well as common metals such as aluminum and copper. The objective of this study was to develop a hydrometallurgical process providing a high selectively between aluminum, cobalt, copper, and lithium from hydrochloric acid solutions. Batch experiment results showed that selective hydroxide precipitation approach was not suitable because a significant amount of cobalt and lithium was co-precipitated with aluminum and copper hydroxides. In contrast, batch experiments and the subsequent data analysis indicated that the sequence of solvent extraction circuits using PC-88A, Acorga M5640, and tri-n-octylamine (TOA) extractants effectively separates four metals of interest. In the first circuit of the proposed process, copper was selectively extracted by Acorga M5640 at the pH 1.0-2.0. Aluminum, cobalt, and lithium remain in the aqueous phase. In the second circuit, aluminium is selectively extracted by PC-88A at pH 2.0-2.5. For the separation of remaining cobalt and lithium, Acorga M5640 provided higher separation efficiency compared to PC-88A single extractant and PC-88A/TOA mixed extractant. However, the stripping efficiency of cobalt from the Acorga M5640 organic phase was found to be low (less than 10 %). Therefore, PC-88A/TOA mixed extractant rather than Acorga M5640 is an advisable choice for the separation of cobalt and lithium. Keywords: spent lithium-ion secondary batteries, solvent extraction, lithium, cobalt

Sep 1, 2012

By G. Bulut

The aim of this study is to produce desiccant clay from a well known Ca-bentonite deposit in Turkey. Towards this aim, bentonite samples were first procured and then subjected to some characterization tests. Various methods were applied to enhance the moisture adsorption capacity of bentonites to a desirable level. These methods include utilization of some additives namely calcium chloride and heat treatment at various temperatures. It is shown that the moisture adsorption capacity Ca-bentonites without any additive are between 14%~17 % (w/w) upon by heat treatment whereas the addition of calcium chloride significantly, raised the moisture adsorption capacities.

Jan 1, 2014

By Jiajun Geand, Shuli Wang, Baodong Pan, Xueqi Cui, Guangwei Zhang, Jipeng Sun

Gravity-fed three-product dense medium cyclone(GTDMC)is usually used as the main coal washing equipment in coking coal preparation plant. It can produce three products with a low density suspension at the same time. Raw coal and dense medium are fed separately into the cyclone. Only the qualified low-density medium suspension is pumped into the cyclone while the raw coal is fed into the first-stage 1200mm cyclone axially at the top end by gravity. The 1200mm cyclone with a cylindrical form is for low-density separation. The clean coal with light density and slower-settling velocity moves directly towards the low pressure zone along the axis and is carried through the vortex-finder to the overflow. Only the heavy products pass through the "separating zones" to the wall of 1200mm cyclone and then migrate into the series-connected second-stage 850mm cyclone through the tangential outlet. The medium suspension from the first-stage cyclone is thickened and contains more magnetite coarse particles. The second-stage cyclone typically consists of a cylindrical section and conical part. These are all favorable for the second-stage cyclone to separate at a high density. Production practices show that the clean coal and the gangue rarely mixed in the middling, the lower limit of the separation is 0.2 mm, the Organic Efficiency and the Ecart probable of the first stage is 98.30% and 0.026 kg/L respectively.

Jan 1, 2014

By Saveliy F. Kaplan, Valeriy N. Tsyplakov, Vasily N. Kovalev, Igor A. Agapov, Nikolai V. Vorob’ev-Desyatovskii

"Based on the experiments, a possibility of successful processing of double-refractory gold sulphide concentrates with a high content of natural organic carbon, which has a high sorption capacity toward gold chloride complexes, has been demonstrated. The proposed approach involves deep burnout of sorption-active organic carbon in an autoclave at a higher temperature and a longer retention time. INTRODUCTION It is known that one of the reasons why gold-bearing ores and concentrates are refractory is the occurrence of fine gold in sulphides (usually in pyrite and arsenopyrite) in ores and concentrates. In addition, refractory gold-bearing ores and concentrates also contain an organic carbonaceous material, which has a sorption capacity towards gold chloride complex, making the ore or concentrate even more refractory. In pressure oxidation, metallic gold is oxidized by Fe (III) aqua-ions and complex Au(Cl)4- ions are formed at temperatures over 180°C, in the presence of chlorides contained in ores. Complex gold anion is adsorbed on the organic carbon surface and then reduced to Au0; the chloride ion is regenerated and gold, adsorbed on organic carbon microparticles, is ultimately transferred to tailings (preg-robbing). Currently, there are several suggestions how to suppress preg-robbing (Simmons, 1998, Pyke, 1999, Rees, van Deventer, 2000, Zhao Jun-wei, 2008). It can be done by reducing the organic carbon content by processing (flotation, etc.),reducing chloride ion concentration by preliminary washing of concentrates in thickeners, reducing the adsorption capacity of organic carbonaceous material by introducing some organic substances that are strongly adsorbed on its surface (blanking agents), and reducing the redox potential of the slurry liquids by introducing neutralizing agents (limestone)."

Jan 1, 2018

By M. Mezzetti, E. Anders, O. Popov, P. Hoske, H. Lieberwirth, M. Voigt

"The material breakage induced by high energy electric discharges is known in general as electric impulse technology. This technology can be used for processing solid materials, such as rocks and ores. The electric impulse technology has been around for about 60 years, originally developed and intensively investigated by Russian researchers. However, the application fields have been limited to research and laboratory scale projects. Currently, there are new attempts to transfer this technology into practical industrial applications. Practical examples include drilling of deep geothermal wells with an electric impulse driven drill-head. Traditional comminution implies high energy consumption, hence, high costs. The Electric Impulse Technology is interesting for comminution of mineral and complex ores since it could allow improved recovery and energy reduction, thus resulting in significant savings. Another advantage is the dust free processing, which contributes to make minerals processing environmentally friendly. The use of electrical comminution for processing complex ores is investigated within the ELIZE research project funded by the BMBF (project No. 033R161 A) and industrial partners. The main objective is the development of an industrial scale electrical comminution machine. The first development stages include the investigation and characterization of the electric impulse induced weakening on rocks and ores. The characterization results of the preliminary trials at the microstructural scale on granite, skarn and greisen will be presented and discussed in this article. INTRODUCTION The pioneer work in the area of electric impulse technology was conducted by Russian researchers about 60 years ago [1]. While there have been some successful attempts to transfer this technology into practical applications, such as rock processing [2], laboratory processing of mineral ores [3–5], recycling [5] and geothermal drilling [6–9], the jump into practical industrial large scale application has not been accomplished yet. The Institute of Mineral Processing Machines of the TU Bergakademie Freiberg currently leads a project which can be seen as the next logical step for the technology transfer to industrial applications, namely, the development of continuously operating complex ore processing machines based on the electric impulse technology."

Jan 1, 2018

By F. Karakas

In this investigation, one of the most energy consuming stage of the cement manufacturing process, grinding stage, was studied. The aim of the study is to reduce the energy consumption. Optimum operating parameters were determined. Experimental studies were performed at three differ-ent stages. Grinding of limestone, clay and marl which are the main components of the cement, to approximately below 90 microns, was the first stage of the cement grinding. At this stage, effect of feed size and ball charge were investigated. At the second stage, the Bond work index of clinker and additives (slag, trass, limestone and gypsum) was found separately. After forming composite cement with clinker and additives, the Bond work index of this mixture was also determined, thus the results of separate grinding and grinding of mixture were compared. The Bond work index of mixture was found as 13.59 kWh/t, while the arithmetic mean of the Bond work index values of components was 14.90 kWh/t. Finally, clinker and additives (slag, trass, limestone and gypsum) were ground under the same conditions. At this stage, laboratory type of ball mill was used in order to understand grinding characteristics of the cement components. As a result of the experiments, it was found that energy consumption for the grinding will be lowered if the mills with 38 % ~ 40 % ball charge are used in the cement grinding. Moreover, grinding with mixture of clinker and additives gave better results than separate grinding of these components in terms of energy consumption.

Jan 1, 2014

By Nina Panteleeva, Elena Afonina, Stanislav Titkov, Jury Buksha

"Flotation processing of water-soluble minerals (potassium ores, sedimentary salts of salt lakes) is currently the main method for production of potassium fertilizers and concentrated carnallite which is the initial product for production of metallic magnesium. Flotation of sylvite (KCl) and halite (NaCl) is carried out in the electrolyte solutions: KCl-NaCl-H2O and KCl-NaCl-MgCl2-H2O. The report presents the results of studies of the effect of concentration and the electrolyte type on the size of air bubbles in a flotation cell in comparison with the floatability of mineral constituents of potash ores. The floatability in electrolytes of various compositions has been studied: - of sylvite (KCl) by alkylamines, - of halite (NaCl) by alkylmorpholines, - of silicate-carbonate slimes contained in the ore by ethoxylated surfactants. The reagent modes (regimes) activating the flotation desliming of potash ores have been developed."

Jan 1, 2014