Search Documents

By Arash Maghsoudloo, Asli Can

"Abstract This paper presents a ground improvement implementation case under a raft foundation of a local hospital. The selected ground improvement method is Wet Soil Mixing (WSM) technique. Soil mixing is increasingly applied to environmental applications and ground stabilization in geotechnical projects. In this technique, weak soil is mixed with cementitious slurry to improve the characteristics of the soil. The investigated case is one of the pioneering WSM ground improvement technique implementation cases in Turkey. The soil profile is mainly consisted of low plasticity clay. The effect of ground improvement is verified by a series of laboratory tests and four in-situ pile loading tests. The results of in-situ pile load tests on constructed soilcrete columns showed an acceptable factor of safety for the bearing capacity of the WSM columns. Measured bearing capacities in all four tested columns were nearly 20% higher than calculated values. In addition, a set of samples are obtained from the constructed columns and unconfined compression tests have been conducted. The laboratory test results indicate that the selected cementitious slurry has a sufficient efficiency to form the stabilizing columns.IntroductionIn the construction industry, stabilization of the soft ground by lime or cement stabilization is a widely used technique. In ground improvement systems deep mixing method (DMM) results in the same stabilization in deep portions of the soft soil profile by mixing cementitious slurry by means of mechanical augers. The pioneering cases of modern deep mixing application can be traced back to the year 1970 that was used for the stabilization of marine soils below the water level for the construction of harbor structures (Terashi et al., 1979). Nowadays, DMM is shown to be a proper and efficient method for the foundation of the structures and embankments on land. Some recent studies also reported that reasonable settlement reduction range in the stabilized soils under the foundation of structures (Archeewa et al., 2011). In addition to reduction of the structural settlement under service loads, deep mixing methods are also utilized when there is a concern with contaminated soil and groundwater or groundwater control (Andromalos and Bahner, 2003).Although, the DMM is shown to be a successful method in numerous studies for improvement of a wide range of soil types such as organics, fine-grained, and coarse grained material, it has some limitations (Archeewa et al. 2011, Jameson et al. 2010, Jelisic and Leppanen 2004, Lambrechts and Roy 1997, Meyersohn 2007, Miki and Nozu 2004, Olsson et al. 2008, O’Rourke and McGinn 2004, Stewart et al. 2004, Yang et al. 2011). High soil density and stiffness could damage deep mixing rigs. Engineering properties of the soilcrete columns changes based on the soil type, water content and other factors such as organic content of the available soil profile, so properties of the generated soilcrete should be verified by a set of rigorous testing procedures (Puppala et al. 2004).Based on the general classifications presented in the ground improvement literature, deep soil mixing method is divided into two main types of dry or wet mixing methods. In the dry and mixing methods compressed air and water are utilized as the binder transporter medium respectively (Moseley and Krisch, 2004). In addition, DMM methods can be categorized based on the employed mixing methods during the construction. In this study, the main aim is to present and elaborate on the selected method is known as Wet Speed Soil Mixing (WSSM)."

Jan 1, 2014

By Dena Morgan, Emre Biringen

"Abstract This paper discusses the execution of pile installation and design issues at two environmentally challenging industrial sites in North America. Environmental regulations set constraints on the design and require versatility in choice of technology.For a proposed bridge, due to protected fish habitat, performing soil borings within 30 m of the creek embankment was prohibited. The limited subsurface profile indicated a thick upper layer of granular material, thus driving H-piles was considered. However, to limit generation of vibration and noise in the protected area, drilled piles had to be used. During execution, the subsurface profile differed from that in the borings 30 m away. Very soft, saturated silt was encountered at the bottom of the caisson and the length had to be redesigned very quickly while the contractor waited for instruction. For a new structure in uncontrolled fill area, performing soil borings was not allowed. It was known that a layer of peat was present in the area, but no information regarding the thickness and extent. The subsurface profile generally consisted of granular material overlying a thick compressible silt layer. Somewhere within the granular layer peat would likely be encountered. Franki piles were chosen to penetrate the peat and bear in the underlying granular material. During environmental sampling in the area, methane gas was encountered and Franki piles were no longer a viable option due to safety concerns. The foundation system was changed to steel H-piles driven to bedrock, which was more than 50 m below the ground surface and sloping. Rock shoes that would work to significant slopes had to be used in order to increase the likelihood of good embedment within the bedrock. Also, due to obstruction of an approximately 3 m thick debris field that was encountered in the upper granular soils, some of the piles had to be relocated and extra piling needed to compensate for such differences. The results of PDA testing to estimate compressive capacity and a series of lateral load tests are presented.INTRODUCTIONThe design issues that are encountered during construction can be quite problematic and have a significant impact on schedule. In order to avoid such impact on the project, a thorough subsurface investigation should be considered prior to design and construction. Better understanding of environmental regulations also prevents costly changes to the foundation design. This paper discusses the execution of pile installation and the design issues at two environmentally challenging sites in North America.BRIDGEDuring the subsurface investigation for a proposed industrial building complex, several boreholes were drilled within the footprint or in close proximity of various structures, with Standard Penetration (SPT) sampling of the upper coarse-grained soils (sand/gravel) and undisturbed sampling of the lower fine-grained soils (silt/clay). The SPT blow counts (N60) were corrected by a factor of 1.35 in order to incorporate the SPT automatic energy transfer ratio. When Modified California Sampler was used, a correction factor of 0.44 to 0.64 was also applied. N60 values were further corrected for gravel to avoid artificially high blow counts during the analyses due to spoon samples contact with gravel and cobbles, and the corrected values of (NG)60 (limited to a maximum value of 50 blows/300 mm) were used for design. The information from the SPT boreholes was then used to assess the subsurface conditions beneath the structures, as well as for a nearby bridge that was designed to cross over a creek. Since performing soil borings within 30 m of the creek embankment was prohibited due to the protected fish habitat, the investigation with regard to the bridge abutments was limited to two deep boreholes (B10-33 and B10-34) at the bridge location and two additional boreholes (B10-35 and B10- 36) located approximately 200 m upstream. The bridge location and two sets of boreholes are"

Jan 1, 2014

By A. R. Dover

The Richmond San Rafael Bridge (Figure 1) is a 4.3 mile long major toll bridge span across northern San Francisco Bay. Tutor-Saliba/Koch/Tidewater (TSKT) conducted a comprehensive seismic retrofit, which was at the time Caltrans? largest-ever construction contract at $484 million. The robust foundation retrofit design of 11 bridge piers included the installation of 26 new, large diameter (126 to 162 inch OD, wall thickness 1.5 to 2.25 inches) CIDH and CISS piles, with steel pipe piles installed to tip elevations of Elev. ?140 to -220 ft, in water depths up to 70 feet. The open-ended steel pipe piles had initial sections ranging from 71 to 172 feet long, with full lengths that extended to the bay bottom and then through 100 to 130 feet of marine sediments to top of bedrock. The marine soils of most interest consisted mainly of soft to firm Young Bay Mud (YBM), a silty, moderately-sensitive clay common to SF Bay. A key constructability issue was the prediction of pipe piles ?running? under self weight (198 to 625 kips in air) and pile driving hammer weight (IHC S-500 with total assembly weight of 322 kips). The term "pile running" is used to describe the penetration of the pile into the soil due to the self-weight of the pile only. This issue was critical because 1) there was limited head room under the bridge deck, and 2) if piles run too deep, the pile splicing on several piles would be problematic (the lowest desirable pile top elevation after running was +10 ft). While running measurements are sometimes made during marine/nearshore construction, there is little published data on predicted vs. actual running. This paper discusses the running prediction under self weight for 26 piles, and the methodology used in developing the predictions, which ranged from 15 to 94 ft of penetration below mudline. Pile running was recorded and compared with predicted values. The prediction methodology was quite good, and no significant constructability problems were encountered. The authors ?tweaked? the model to provide a slightly improved prediction method. The paper presents the model, predictions, observations, and discusses important lessons learned.

Jan 1, 2006

By Michael J. Brown

Load testing is important for controlling the quality of piled foundations. The Statnamic test is an alternative to existing testing methods with a load duration that lies between that for static and dynamic tests. Current methods of analysis offer excellent correlation between static and Statnamic tests for coarse-grained soils but often over-predict the capacity for fine-grained soils. Thus a calibration chamber is being used to produce instrumented beds of clay with reproducible properties. A model pile placed in the beds can be loaded at varying rates using a computer controlled servo-hydraulic system. Results from the modelling will be used to improve methods of analysis and govern the design of a full-scale study. Initial results suggest the rate effect can be represented by a power law relating pile velocity and resistance. Statnamic loading of the model pile produced large negative pore pressures in the clay bed.

Jan 1, 2002

By Andrew McNamara, Stuart Norman, Matthew Dearing, Michael Pelken, Asha Panchal

The deep foundations industry has largely remained unchanged since in the advent of CFA piling in the 1960s. Piles have consequently been designed and constructed following the traditional codes and standards without much regard for optimising in-life efficiency or end-of-life reuse. After existing developments have been demolished there is little motivation to reuse existing piled foundations as their load bearing capacity and structural integrity cannot be verified. Therefore piling contractors are increasingly spending more resources on coring through existing piles, only to be replaced with larger diameter or deeper piles. The hollow element of the HIPER® Pile provides access to the entire length of the pile to permit inspections and a shaft in which the pile can be extended if needed. This paper presents and compares the embodied carbon savings, both during construction and through foundation reuse, from a HIPER® Pile scheme compared with the traditional solid pile scheme. A discussion on the benefits of this technology and its implications on warranties and approvals is also presented to motivate the foundations industry to embrace whole lifecycle assessments and support the journey to net-zero carbon.

May 1, 2022

By Sameh M. Khella

This paper discusses the application of deep CFA piles for the foundation of structures in different ground stratifications with a focus on the application in Queensland region. Design, construction techniques and quality measures implemented during these procedures are described. Testing methods and verification of capacity, integrity and performance of these piles are also demonstrated. Case studies for this application are presented with an appreciation of this solution within the provided project conditions of each case. Examples of successes and challenges encountered over the course of application of deep CFA in Queensland are mentioned. Limitations of the technique and less favourable situations for its implementation are also highlighted.

Nov 1, 2022

By James S. Graham

Specifications for treated round wood piling are presented for the engineers consideration. Included in the text are background information, technical committees, Chellis, quality, treatment, static and dynamic stresses, accessories, and existing codes and standards. The specifications are also available using Word Perfect on 3.5 or 5.25 inch size disks provided by the National Timber Piling Council. Note: DFI recommended wording is wood, head, and toe, instead of timber, butt, and tip.

Jan 1, 1992

By Bret N. Lingwall, Byron Foster

The problem of reliable extreme event modeling of large diameter piles under enormous structural or kinematic loads has gained more attention in recent years. In particular, the soil response around the foundation and impacts to buried adjacent infrastructure has gained interest. One of the principal shortcomings with analysis of large diameter pile foundations under extreme event lateral loading is the reliance on conventional beam on elastic foundation methods, which do not model the soil field response around the pile. These methods are limited for large displacement problems, and for large diameter piles. However, the fundamental interactions between steel and concrete, and structure to soil are difficult to constrain, especially in large strain problems where the structural elements become inelastic. The non-linear interaction of the structural materials and soil is desirable so that assessment of stress changes in the field and effects on adjacent facilities can be modeled. A numerical modeling methodology that addresses these shortcomings has been developed. This method utilizes the interaction of brittle concrete with discrete steel reinforcing and casing in a robust manner capturing inelastic non-linearity in both soil and structure. This paper presents a comparison study of the method, wherein three different validation studies were made to data from full scale laterally loaded pile testing. INTRODUCTION Extreme event lateral loading of deep foundations comes in many forms including earthquakes, landsliding, tsunamis, hurricanes, surface fault rupture, liquefaction induced lateral spreads and many more. These extreme events induce loads on foundations far greater than service or strength loads. Perhaps the most dangerous extreme event loads are those of large soil displacements such as landslides, lateral spreads, and surface fault rupture, wherein the soil surrounding the foundations can move laterally 100 mm to 3 m! In these extreme event loading scenarios, small diameter foundations are pushed past their limits and many engineers prefer large diameter deep foundations for these situations. These deep foundations of diameter 900 mm or greater may be auger cast in place piles, cast in drilled hole piles, cast in steel shell piles, cased or uncased drilled shafts, bored precast piles, etc. For convenience in this paper, large diameter deep foundations will be referred to as Large Diameter Shafts (LDS). In LDS, steel may or may not used as a shell around the perimeter of the concrete and/or as internal tensile reinforcement. The interaction between brittle concrete and ductile steel within and/or along the perimeter of the LDS is critical to understanding the non-linear inelastic behavior of LDS for problems of large lateral displacements from extreme events.

Jan 1, 2018

By Bengt H. Fetlenius

The "Pile Prediction Event" at the ASCE GeoInstitute's Deep Foundation Conference in February 2002 involved prediction of drivability and capacity of three 14m long, 324mm diameter, closed-toe pipe piles driven into loose to compact fine sand to slightly silty sand. Predictors were provided the results of two soil borings and three cone penetrometer tests, as well as type and model of hammer to be used for the pile driving. A total of 33 persons submitted predictions. As to penetration resistance distribution, many predictions were far below actually observed values. As to capacity in compression, the predicted values ranged from 270KN through 2,340KN with a mean of 1,070KN. As to capacity in tension, the predicted values ranged from 100KN through 1,650KN. The maximum load applied to the compression pile in the static loading test was 1,25OKN, at which no more reaction load was available. The reaction system for the tension test failed early in the test. CAPWAP analysis on End-of-Driving blows showed capacities at the end of the driving for the push and pull piles of 670KN, and 710KN, respectively. No restrike tests were made. Additional CPT soundings indicate that the pile driving had densified the soil. Static analysis and calculations from the CPT indicated that capacities ranged from 1,000KN through 2,000KN. The paper presents the data and discusses the various methods of determining pile capacity and addresses influence of set-up Lessons useful for future similar events are indicated.

Jan 1, 2004

By Ke Yang, Robert Liang

"Drilled shaft foundations are widely used for many types of structures, especially for highway bridges, high rise buildings, and costal structures. The lateral design considerations are crucial for those structures that are subjected to lateral thrust forces, winds, waves, and earthquakes. The p-y analysis is the most widely used method for the analysis and design of drilled shafts for lateral load applications in soils. However, existing p-y criteria were developed based on the lateral load tests on small diameter drilled shafts in soils. Although, a lot of lateral load tests have been conducted, there are a limited number of lateral load tests on large diameter drilled shafts embedded in clay. In this paper, a lateral load test on 2.44 m diameter fully instrumented drilled shafts in clay is presented. The site specific p-y curves are derived based on strain gage readings. The existing p-y curves are found to be much softer than the site specific p-y curves. Correspondingly, the deflection at the top of the test shaft under the maximum applied load is predicted to be eight times larger than the measured value using existing p-y criteria. A new p-y criterion is proposed in this paper. The proposed p-y criterion is proven to be able to capture the site specific p-y curves of the load test and to predict closely the deflections at the top of the test shaft. INTRODUCTIONDrilled shaft foundations are widely used for many types of structures, especially for highway bridges and costal structures. The lateral design considerations are crucial for those structures that are subjected to lateral thrust forces, winds, waves, and earthquakes. Although efforts have been made on studying lateral response of drilled shafts; nevertheless, only limited studies have been published on the behavior of large diameter drilled shafts under lateral loads and the corresponding design methods."

Jan 1, 2005

By S. F. Fu

The Charkhan Salt Lake area of the Chaidamu Basin in West China is characterized by soft super-saline soils with very high contents of soluble salts. From the engineering point of view, these saline soils are saturated, liquid-plastic and moderately to highly compressible lean silty clay and clayey silt. In the natural state, their allowable bearing capacity is only 60-80 kPa. As to the saturated lean silty clay, liquifaction in case of an earthquake of intensity 7 on the Modified Mercalli scale is considered likely. In order to improve the geotechnicai properties of the saline soils, stone colomn stabilization by means of vibroflotation was performed. As the geotechnicai properties of the soils are closely linked with the amount and composition of the soluble salt content, saline water with chemical content similar to that of the saline soils was used as flush fluid in the course of hole-making and column-forming, with a view to keeping unaltered the amount and composition of the salts in the soils and thereby precluding reduction in or loss of their strength. Systematic monitoring on the behavior of the foundation soils before and after the treatment and comparison of the numerical data thus acquired have shown good technical results, testifying to the effectiveness of stabilization of soft superealine soils by vibroflotation. As a result of the treatment, the allowable bearing capacity was increased one to two fold, accompanied by elimination of the liquefaction potential.

Jan 1, 2010

By Jeffrey C. Schuh, Logan Bloemer, Daniel P. Dietzler

Over the past 30 years, the authors have encountered numerous projects where recognizing the geology, soil properties and groundwater conditions, and considering alternative construction techniques have promoted efficient and cost-saving construction. The construction documents for these projects, produced by various engineering firms, provided basic information on geotechnical conditions. The authors became involved in each project either because there was a problem during design or construction or, as a contractor, won the project because they saw a value engineering opportunity to take advantage of the geologic setting of the project to design and build alternatives to what the designer depicted. Understanding the geologic setting is critical before planning and designing begins. Being able to work with the geology and the materials on site is preferred before specifying more costly and complex solutions, which often require the importing of materials and adherence to unnecessary and/or inappropriate specifications. Failing to understand the geology or not knowing all the techniques available for construction can lead designers to develop solutions that could be inappropriate. This paper presents several examples of value engineering and project performance enhancements developed through knowledge of basic soil mechanics and implementing innovative solutions. History and Background Most people attend DFI meetings, present their experiences, listen to others, and read articles and papers with the hope they can learn from others. Geotechnical engineers and contractors often interface with others in the execution of projects who have, at best, a rudimentary knowledge of geology and soil mechanics. Of course, there is a need for architects, bankers, and regulators, etc., but they typically do not have much interest in the nuances of geotechnical engineering, which relies on both art and science. Thus, significant time is spent educating counterparts in the need for comprehensive subsurface investigation programs and the intricacies of construction in the “dirt,” as they typically refer to soil and rock.

Jan 1, 2019

By Magued G. Iskander

The deterioration of concrete, steel, and timber is a serious hindrance to construction in marine and corrosive environments. Composite materials such as fiber-reinforced polymers (FRP) can offer performance advantages for construction in these environments. In the last decade, piling made of FRP composites has been used experimentally throughout North America. However, composites face obstacles because they do not have a long track-record of use in civil engineering structures. A comprehensive review of the current experience in research, testing, design, and practice of composite piling is presented in this paper.

Jan 1, 2002

By Mark D. Fuhriman, Parham Khoshkbari, Robert Fosse

Drilled displacement piles are becoming an increasingly common deep foundation choice for their relatively simple installation methods, applicability to a wide range of subsurface conditions, and versatility. The installation method includes drilling and displacement of the soil followed by delivery of fluid cement grout under pressure, and placement of steel reinforcing to complete the pile. Because the installation method uses blind processes that do not permit direct observation of the pile, it is desirable to employ redundant testing tools to complement good construction techniques and inspection practices to ensure integrity of the piles. This paper examines the use of a range of integrity testing tools used for pile installations at a major office campus development. Because the integrity of a drilled displacement pile and its performance depend to a large extent on the skill and experience of the installation crew, the paper explores how use of multiple practical tools, including automated monitoring tools on the pile installation equipment, thermal integrity profiling, and high-strain dynamic testing, ensure structural integrity of the completed piles and how redundant integrity testing methods complement good construction and inspection practices add confidence in the quality of the foundation system.

Sep 8, 2021

By Joel Moskowitz, Jan Cermak

"New York City has unique geologic conditions which must be considered when designing pile foundations. Where shallow foundations are not feasible, the City's subsurface conditions require a variety of deep foundation systems, ranging from high capacity rock socketed piles, to piles end-bearing on bedrock, to friction piles bearing in alluvial or glacial deposits. Pile load testing is essential in confirming pile capacities as pile analyses include assumptions on soil and soil-pile response, and pile driving equipment. Load test results must be interpreted to estimate the long-term pile behavior. Except for lightly loaded driven piles, the New York City Building Code (the Code) requires that pile capacities be confirmed by static load testing. The Code provides the number of static load tests required, test procedures, and acceptance criteria. In the last few decades, methods other than static load testing have been developed including dynamic and rapid (pseudo-static) load tests. Recently, those methods have also been employed on several projects in New York City. The traditional approach to pile load testing in New York City is discussed herein including engineering involved in the analyses of test data with examples. In addition, several projects which included non-static load testing are discussed INTRODUCTIONPile load testing complements the subsurface information and pile design by providing further data on pile-soil interaction for the selected pile type and installation method. Traditional approaches to pile load testing in New York City involve static load tests to verify the design capacity of the piles for a given minimum factor of safety.In the late 1950's, Dr. Phillip C. Rutledge summarized his views on the philosophy of pile foundations in an unpublished, in-house document. He viewed pile foundations as good illustrations of pertinent and impertinent aspects of geotechnical engineering. In the analyses of piles he divided engineering into four general types:(a) Theoretical engineering in which decisions are made based on theoretical analyses. This represents ideal engineering, in which all factors affecting the pile design are well established or, at least, few simplifying assumptions with known effects on the analyses are made."

Jan 1, 2005

"1.0 DESCRIPTIONThis work consists of furnishing all necessary labor, equipment, and materials to install prefabricated vertical (wick) drains in the ground in accordance with the Plans and as specified herein.2.0 REFERENCED CODES AND STANDARDSASTM D4716-08 Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant HeadASTM D4632-08 Standard Test Method for Grab Breaking Load and Elongation of GeotextilesASTM D4533-11 Standard Test Method for Trapezoid Tearing Strength of GeotextilesASTM D4491-99a Standard Test Methods for Water Permeability of Geotextiles by Permittivity (2009)ASTM D4751-04 Standard Test Method for Determining Apparent Opening Size (A.O.S.) of a GeotextileASTM 6918-09 Standard Test Method for Testing Vertical Strip Drains in the Crimped Condition3.0 QUALIFICATIONSThe Contractor shall have successfully completed a minimum of five wick drain installation projects in similar ground conditions, and installed not less than 5,000,000 linear feet (1,525,000 linear m) of wick drain in the past five years. The Contractor shall have a minimum of five continuous years of wick drain installation experience."

Jan 1, 2014

By Anne Lemnitzer

Full-Scale cyclic field testing was performed on a 3x3 pile group consisting of nine cast-in-drilled-hole (CIDH) reinforced concrete shafts and a comparable single-shaft in order to investigate group interaction effects. Both specimens were constructed with pile diameters of d = 0.61m (2 ft), fixed head boundary conditions, and placed in stiff clayey soil at a test site near the LAX Airport in Southern California. Internal instrumentation was installed in the single pile as well as in three piles within the pile group to obtain pile curvatures. External instrumentation controlled the lateral displacement of the specimens. A combination of experimentally and analytically obtained p-y curves for the single pile was used to simulate results for piles located in the group when field data were not available. All test specimens were tested to structural failure and excavated after test completion to investigate pile damage and plastic hinge formations. Calculated group interaction factors ranged between 1.0 at very small displacement levels of <2.5 mm (0.1 in), 0.8 at the initiation of the pile-soil-pile interaction, i.e. between 4 mm - 15 mm (0.16-0.6 in), and increased towards 0.9 near structural failure (displacement >25 mm or 1 in). A literature set of p-multipliers was found to reproduce an accurate fit to the available load displacement test data from the group.

Jan 1, 2010

By Leykam Chris J., Jacobs Scott. A.

"Construction of the New NY Bridge over the Hudson River 25 miles north of New York City is one of the largest civil infrastructure projects presently underway in the United States (formerly Tappan Zee Hudson River Crossing). The $3.14 billion Design-Build contract is also the largest ever awarded by the state of New York using an Alternative Project Delivery method, and the first major public project to use Design-Build. The new 3.1 mile long bridge will replace the existing Governor Malcolm Wilson Tappan Zee Bridge with a modern twin crossing featuring: Iconic side by side cable stay main spans; significant deck widths accommodating eight lanes of regular traffic, wide shoulders, and a shared use pedestrian and bike path; foundation with excess capacity to fully support a future rail bridge; more than 1,000 large diameter pipe piles driven in deep glacial deposits; drilled shafts installed through steep blast-rock slopes on the east shore landings. Geotechnical challenges included varied bedrock and glacial till surfaces with steep slopes and depths in excess of 750 ft.The purpose of this paper is to highlight major features of the New NY Bridge project with specific focus on the design and construction of the foundations supporting the approach and main span structures from abutment to abutment, provide background on alternative project delivery in NY, as well as provide an overview of the design-build process as it was applied to foundation delivery.The 3.1 mile Governor Malcolm Wilson Tappan Zee Bridge was constructed across the Hudson River connecting Nyack and Tarrytown (Rockland and Westchester Counties). Construction started in March 1952 and was completed in 1955 for a cost of $81 million. The seven lane crossing first opened to traffic on December 15, 1955 and coincided with the opening of a 28 mile segment of highway I-87 / I-287 between Suffern NY and Yonkers NY. The bridge is part of the extensive 574 mile New York State Thruway road system owned and operated by the New York State Thruway Authority (NYSTA)."

Jan 1, 2016

By Amr Sallam, Ahmad Mohamed, Mohamed Alrowaimi

Renewable energy, in the form of wind and solar, has emerged as main source of energy in the modern society. The wind industry has substantially grown over the last two decades to become a key player in providing energy to public. Wind turbines are getting larger, taller, and more efficient every year. The foundation is a major component of the wind turbine system. The wind turbine foundation must provide short and long-term stability for the overall turbine to allow continuous and safe turbine operation for energy production. The turbine serviceability and stability requirements must be geotechnically and structurally satisfied. In North America, major foundation types currently utilized in the wind industry include gravity spread foundation, mono pier foundation, and pile foundation. In this case study, a Post Tensioned Pile Cap (PTPC) foundation was used to support a 3.15-3.4 Megawatt turbine with 125M Rotor supported on 87.5M-hub-height tower. Soil anchors in the form of Auger-Pressure-Grouted-Displacement (APGD) piles and Continuous Flight Auger (CFA) piles were utilized. Four distinct subsoil conditions were identified, and for which four pile designs were adapted. Due to the occasional encounter of stronger soils at 50 to 55 feet (15.2 to 16.7 m), shorter pile design was preferred. To satisfy the design uplift load, pile post grouting were utilized to increase the shaft capacity of the piles. In this paper, the pre-production pile load test program will be described. The pile load test procedure, analysis, and results will be presented. A discussion will be provided, which led to the selection of the optimum pile design to support the high tension loads taking into consideration pile length limitations.

By Aditya Ayithi, William G. Ryan, Dean Herbst

"For rock socketed drilled shafts, it is a common practice not to include the frictional resistance of overburden soils into the nominal capacity estimation. The primary reason often being cited is “overburden soils resistance is negligible compared to that of rock socket resistance.” However, in certain geological conditions, where the rock layer is located at greater depths, friction resistance from overburden layers can be significant. In addition, at such great depths, shaft drilling becomes very complicated and expensive. In these situations, considering the resistance of the overburden layers can be an economic alternative.This paper presents a case study of an Osterberg cell (O-cell) load test conducted on a 161.8 feet long and 78-inch diameter instrumented test shaft. Based on initial designs, a 72-inch diameter rock socket of lengths 23 and 26 feet was required to provide a LRFD factored friction resistance of 3,200 kips. The load test results revealed that the material in the 72-inch diameter socket does not represent a true rock. However, the test results also proved that the factored friction resistance of overburden layers is greater than the required design resistance. Based on the load test results, it was decided to allow the overburden soils frictional resistance to be considered in the shaft design, resulting in significant economic savings.INTRODUCTIONRock socketed drill shaft design guidelines of various State Department of Transportation (DOTs) agencies allow friction and/or end bearing resistance of only the rock socket portion into the design capacity estimation. It is typical to neglect the frictional resistance of overburden soils. However, in certain geological conditions where the rock layer is at greater depths, friction resistance of the overburden soils can be significant. In this case the friction resistance of overburden soils was verified via the specified instrumented O-cell test program and then used as part of the design capacity.PROJECT DESCRIPTIONAs part of I-29 improvement project, Iowa Department of Transportation (Iowa DOT) planned to replace the dual four lane bridges that cross the Floyd River in Sioux City, Iowa with dual six lane bridges (Fig. 1). Expected benefits from this improvement include improved safety, traffic operations and roadway infrastructure conditions.BRIDGE SUBSTRUCTUREThe project consists of two individual bridges; a new south bound bridge and a new north bound bridge. The south bound bridge is 646-ft long and the north bound bridge is 644-ft long. Both are six-span, pretensioned and pre-stressed concrete beam bridges of varying width. Bridge foundations were designed such that the abutments of both bridges will be supported on driven steel piles and the bridge piers will be on drilled shaft foundations."

Jan 1, 2016