Search Documents

By B. B. Broms

Embankment piles are common in the Scandinavian countries (Kjellman, 1940) and in Southeast Asia as support of fills, light structures, bridge abutments and deep excavations (Eide, 1968) as described in the following. Untreated timber piles are often used for light structures and shallow fills when the ground water level is high since they are inexpensive and readily available. When the applied loads are relatively high precast concrete piles and steel piles are preferred. DESIGN CONSIDERATIONS Embankment piles carry the load from a fill or a struc-ture either through skin friction along the sides of the piles (Fig. 1a) or through a precast concrete slab or through pile caps at the top of the piles (Fig. 1b). When the load is carried by skin friction it is often economical to use small diameter timber piles because of the large surface area (Asplund, 1939). For precast concrete or steel piles concrete caps are used to transfer the load to the piles due to the relatively high capacity of the piles since the skin friction resistance alone is not sufficient to transfer the load to the piles.

Jan 1, 2010

By Osama El-Fiky

There are many types of deep foundations currently being used in the San Francisco Bay Area, one of the most common being driven precast, prestressed concrete (PC/PS) piles. PC/PS piles are frequently selected for use due to of ease of installation, availability, and relatively low cost. Disadvantages of using PC/PS piles are noise, vibrations, pollution, front-end delays due to indicator pile programs, and reduced flexibility. An acceptable alternative to driven PC/PS piles was selected for construction of foundations for the heavy housing and administrative buildings at the San Francisco County Jail #3 replacement project in San Bruno, California. The pile type selected, the Auger Pressure Grouted Displacement (APGD) pile, was chosen to reduce noise, vibrations, installation time, and cost, and to allow for greater flexibility of installed pile lengths. This paper presents a case history of the use of APGD piles that were substituted for driven PC/PS concrete piles for the subject project. Standard and quick loading pile load tests were performed to confirm adherence with the design criteria originally used for the driven PC/PS concrete piles. The APGD piles were found to increase shear strength around the piles similarly to driven displacement piles. In addition, this paper presents the methodology used in monitoring APGD pile installation.

Jan 1, 2002

By Thang V. Nguyen, Lisheng Shao, Gary E. Taylor

"The Community Memorial Hospital of Ventura, California, proposed to build a new state-of-the-art Cancer Treatment Center with radiation shielding walls and roof. The loose silty soils at the site had the potential to liquefy during an earthquake, which would result in significant settlement under the heavy footing loads. Treatment options included various deep foundation alternatives, as well as several ground improvement methods. The choice of wet soil mixing minimized the disturbance to the adjacent hospital during construction and potential settlement. Wet soil mixing allowed the structure to be supported on a raft foundation, meeting the stringent building total and differential settlement criteria. The authors also performed unit cell 3-D finite element analyses to evaluate the behavior of the wet soil mixing system in seismic loading conditions. This paper highlights the ground improvement design, construction, QA/QC, and the research related to evaluating the effectiveness of soil mixing for liquefaction mitigation.INTRODUCTIONThe Ventura Community Memorial Hospital proposed the construction of a new Cancer Treatment Center to replace the existing structure, which was built in 1901. The hospital complex is located in a wellestablished residential neighborhood. The soil conditions at the site of the proposed structure required ground modification to support the very heavy radiation treatment section of the building and limit settlement. Originally, 90-foot-long precast piles were considered for foundation support. Based on supplemental Cone Penetration Tests (CPTs) performed, the deepest CPT did not encounter competent pile bearing strata at a depth exceeding 30.5 m (100 ft). This could result in failure of the piles under long-term conditions, especially if hydro-consolidation occurs. The more realistic pile penetration depth would have been 36.6 to 45.7 m (120 to 150 ft). In addition, the excessive noise in association with pile driving would have been unacceptable to the community, patients, and staff of the hospital, so an alternative ground improvement solution was required.The specialty geotechnical contractor recommended wet soil mixing, an economical solution of creating a soil-cement product known as soilcrete that would significantly reduce the construction related noise and provide a more complete deep foundation for the structure.SOIL CONDITIONS AND SETTLEMENT CONCERNSThe subsurface soils were interbedded (Fig. 1) consisting of loose to medium dense silty sands, and soft to medium stiff silty clays to a depth of 30.5 m (100 ft). Groundwater was encountered at depths of 9.1 m (30 ft) and historical high groundwater was at 8.5 m (28 ft) below the ground surface."

Jan 1, 2015

By K. Viking

The vibratory characteristics of full-scale sheet piles, vibratory driven into the ground, have so far not been described systematically in detail. This paper concerns the preliminary results of a series of full-scale field tests where both the driveability and induced ground vibrations have been continuously monitored. Furthermore, the results of measured ground vibration levels have been measured at two different sites characterised as having hard and easy driving conditions. In the light of the presented results, the paper briefly discusses how the complexity of a driveability and vibration prediction can be subdivided into three parts, namely, vibrator-, sheet pile-, and soil-related parameters, all of which significantly affect both the driveability and induced ground vibrations.

Jan 1, 2000

By Emad W. Shublaq

Contractual site plans are implemented for executing pile foundations (5 x 5) at segmental concrete bridge. Project schedule demands have forced the contractor to find out the most economical procedure in achieving the goal. This paper presents a site management technique which is applied by the Contractor. This was found to be fruitful and as much as 60% saving was gained.

Jan 1, 1992

By L. F. Miao

Studies were carried out to investigate the ultimate soil pressure acting on pile(s) undergoing lateral soil movement in soft clay. A special apparatus has been designed to apply a uniform rectangular profile of lateral soil movement on the rigid pile(s) with pinned head and tip conditions to obtain the ultimate soil pressure. The piles were 16 mm (5/8 in) in diameter. For the pile group tests, the behavior of different number of piles (2, 3, 4, 6 and 9), pile arrangements and center-to-center spacings (3 and 6 diameters) were investigated. In this paper, the group factors of 11 combinations of number of piles, pile arrangements and pile spacings are presented. The group factors are given for individual piles in a pile group as well as for the entire group. Generally, the group factors of individual piles in a group varied significantly according to pile spacing in both directions, and pile arrangement; the group factor of the whole group reduced with an increasing number of piles, and increased with increasing pile spacing. For a pile group with the same number of piles but different pile arrangement, no significant difference was found in the group factors for the entire group.

Jan 1, 2008

By Patrick J. Hannigan

The pile foundation designer typically performs a subsurface exploration program and static pile capacity calculations before selecting a pile foundation type, length, and capacity. During construction, a pile installation criterion must be established to meet these design requirements. This installation criterion usually consists of a minimum penetration resistance or blow count to confirm pile capacity and may also include a minimum embedment requirement. This text will focus on use of wave equation analysis and dynamic measurements to meet design requirements. BEFORE THE WAVE EQUATION Since the mid-1800s, over 450 dynamic formulas for pile driving control have proliferated. In their simplest form, these formulas relate hammer energy to the work of soil resistance, or simply: W ? h = R ? s (1) Where W = ram weight h = ram drop height or stroke R = pile capacity s = pile penetration per blow

Jan 1, 1990

By Donald Bruce, Mark Harris, Wesley Schmutzler, James Sanders

"This paper evaluates the history, construction and most importantly the performance of two remedial seepage cutoff walls installed in two major dams in the United States. Beaver Dam, on the White River in northwest Arkansas, was completed in 1966 and seepage through the karstic limestone under the embankment was apparent almost immediately upon filling of the reservoir. Several attempts to stop the seepage by grouting were unsuccessful. In 1994 a cutoff wall consisting of secant piles drilled with 32"" diameter down-the-hole hammers to a maximum depth of 185'?was completed and the seepage was reduced to a negligible amount. It has been over 20 years since the completion of the cutoff wall, and all indications are that the cutoff wall is performing as expected. Walter F. George Lock and Dam on the Chattahoochee River near Fort Gaines, Georgia, was completed in 1963 and suffered the same problem as Beaver Dam due to the limestone on which the dam was founded. Cutoff walls were installed in both embankments (1980s) and solved the problem in these areas, but under-seepage at the concrete lock, dam and spillway structures increased to the point that remediation was essential. The cutoff wall had to be installed through 110'?of water and another 100'?into rock upstream of an active dam that continued to generate electricity during the construction of the cutoff wall. A secant pile wall, in combination with a diaphragm wall, was completed in front of these structures in 2004. It has been over 10 years since the completion this cutoff wall and, again, the cutoff wall is performing as expected. The paper describes the construction of these cutoffs, but focuses on the long-term performance in terms of controlling seepage and piezometric levels.BEAVER DAMBeaver Dam is located on the White River, 609 miles above its mouth, in Carroll County, Northwest Arkansas. The construction of the dam and Beaver Reservoir was authorized on September 1954 by the Congressional Flood Control Act for purposes of water supply, flood control and hydroelectric power generation. The dam site was selected in 1957: construction began in November 1960 and was completed in June 1966. (FIG. 1)"

Jan 1, 2017

By Maurizio Siepi, Fabio Santillan, Lyndon Bedford, Carlo Crippa

"Abstract: Wolf Creek dam, on the Cumberland River in Kentucky, US, operated and maintained by the Nashville District of the USACE, is the Corps' largest reservoir east of the Mississippi river. The 1748 m (5,736 ft) long Wolf Creek dam combines earthfill and concrete gravity sections. Construction began in 1941 and was completed in 1950. The dam showed signs of instability in the 1960’s, and in the late 70’s an in-depth project of rehabilitation was undertaken, using both grouting and secant piles. The works saved the dam, but in the late 90’s further signs of distress worried the Nashville district of USACE which, after a study conducted on the water seepage, concluded that construction of a new concrete barrier cut-off wall was needed. In 2009, the $341.4 USD million contract was awarded to TREVIICOS-SOLETANCHE JV.The new wall, located upstream of the concrete monoliths, has a minimum thickness of 60 cm (24 in.), and runs the length of the embankment, into the right abutment, for about 4,200 feet. The founding depth reaches 84 m (275 feet), well below the zone of solutioning. With a total surface approaching 92,903 sq.m (1,000,000 sq.ft), the Wolf Creek barrier wall is unlike any other project in the world.The construction of the cut-off wall followed a complicated but logical sequence of several operations, involving a variety of technologies: grouting, hydromill, directional drilling, and secant piles with reverse circulation. The intensive rock grouting program was aimed to minimize the risk of slurry loss and extend the positive cut-off further deep. Subsequently, an Encasement Concrete wall was installed with hydromill, toeing into the rock, to protect the embankment during the following phases. Smart holes were then drilled into the Encasement wall down to the final depth. Eventually, the holes were used to install the secant piles by employing the reverse circulation piling method.An extensive verification campaign has confirmed the superior quality of the cutoff wall consisting of 1200 secant piles, exceeding by far USACE’s requirements. The main project was substantially completed in early 2013. A small portion of secant piles wall will be installed downstream of the dam, to close the switchyard, finishing the project in the early months of 2014.IntroductionWolf Creek Dam is located on the Cumberland River in south-central Kentucky. The Nashville District of USACE operates this multipurpose dam to provide hydropower, flood control, water supply, and water quality benefits for the Cumberland River system and surrounding region. Lake Cumberland, created by the dam, impounds 7,400 million cu.m (6 million acre foot) at its maximum pool elevation of 232 m (760 ft) above sea level. This lake is the largest reservoir east of the Mississippi and the ninth largest in the United States, and attracts 4.89 million visitors, more than Yellowstone National Park (2.87 million).This paper describes the recently completed works for the rehabilitation of the dam, accomplished by TreviICOS-Soletanche JV with the construction of a new Barrier Wall."

Jan 1, 2014

By Gerald E. H. Verbeek

As the number of driven concrete piles with Embedded Data Collectors increases, it has become possible to compare the widely used Beta Method to assess pile damage (using the change of pile impedance) with the so-called Measured Pile Integrity (MPI) method (a combination of two approaches using both the change of pile impedance and the change in pile pre-stress levels). After a brief introduction of both methods, this paper presents the outcome of that comparison based on data from more than 400 concrete piles driven in Florida, which brings into question the reliability of any damage assessment method based solely on the change of pile impedance (such as the Beta Method), especially to detect damage near the pile toe. Moreover the paper demonstrates the need to re-assess the damage classification used for the Beta Method as well as the use of Pile Driving Analysis (PDA) to detect pile toe damage.

Jan 1, 2011

By Eugene Mirsky, Eloy Ramos, May ElKhattab, John Wise, Terrence Carroll, Jose Torres

In 2017, Nicholson Construction Company completed a $72.1 million design-build contract for Miami Dade Water and Sewer Department to replace an existing 54-inch diameter pre-stressed concrete force main that runs from the Virginia Key Central District Wastewater Treatment Plant, under the Biscayne Bay at Norris Cut, to Fisher Island. In order to install the new sewer pipe below the bottom of Biscayne Bay, a tunnel boring machine (TBM) was launched from a 42ft diameter and 89ft deep shaft on Virginia Key and a precast segmentally lined tunnel was constructed towards a 28ft diameter and 72ft deep retrieval shaft on Fisher Island. Both shafts were constructed through sand and highly permeable limestone, primarily the Fort Thompson Formation which is part of one of the most permeable aquifers in the United States and two different techniques were used to ensure a water-tight shaft at each end of the tunnel drive. The launch shaft structure was built using the secant pile technique, wet excavation and a tremie plug. For the tunnel break-in a soil freeze block was installed after the ground was treated with low mobility grout. The retrieval shaft was built using the Deep Soil Mixing (DSM) technique and excavated in the dry. Precedence of any other structure built this deep through hard layers (UCS over 3,000 psi) using this technique was not found. This case study addresses the challenges of constructing watertight underground structures in highly porous ground for launching and retrieving a TBM. Design challenges from complex asymmetric loading, selection and comparison of the construction techniques, the installation and excavation of both shafts, and their performance are also discussed herein.

Jan 1, 2018

By Luca de Sanctis

The analysis of piled raft foundations in layered soils may be performed by 3D finite elements or by approximate procedures. Among the latter, the code NAPRA (Russo, 1998) is based on the method of the interaction factors and accounts for soil layering by the so called Steinbrenner approximation. A comparison between the results of 3D FEM and NAPRA for some reference layered soil profiles shows that the approximation is fully acceptable for engineering purposes, provided the stiffness of the single pile is properly selected. The interest of the conclusion lies in the fact that the amount of work needed to model a practical problem by NAPRA is but a fraction of that needed by FEM modelling.

Jan 1, 2002

By M. Dondelinger

This paper presents a comprehensive review of steel sheet piling including internationally manufactured hot rolled sections, their history, applications, installation and driving techniques. The discussion will cover both temporary and permanent installations; temporary piling used in construction of cofferdams with various bracing systems, deep foundation installations for buildings, bridges and tunnels, etc., and permanent piling used for highway, railroad and bridge construction as well as for riverbanks, piers, wharfs and docks, normally required for port facilities. In addition, cofferdams, as self-supporting gravity structures where interlock strength is of prime importance, will be discussed. The design and application of light, intermediate and heavy sections will be presented including heavy combined walls and information on Z-shaped, U-shaped and HZ sections and their corresponding interlocks. Emphasis is placed on new developments for design applications for deep foundations and waterfront structures within the "state of the art".

Jan 1, 2010

By Paolo Heiniger

The aim of this paper is to present the operative solutions devised and then adopted to implement the underexcavation (soil extraction) of the Tower of Pisa, by means of soil extraction. The intervention has been performed by the Consorzio Progetto Torre di Pisa, a joint venture made of five qualified Italian companies (Trevi S.p.A. , Rodio S.p.A., Italsonda S.p.A., Ismes -Enel Hydro S.p.A., Bonifica S.p.A.), selected for their experience in the field of monitoring and restoration of monuments, structural design, foundation engineering and specialised works in underground conditions. Since 1991 the Consorzio has been charged with the specific task of implementing, within the contractual frame of a Concession, all the decisions made by the International Multidisciplinary Commission appointed by the Italian Government the previous year, with the aim at solving the «problem» of the Tower, strengthening the structure and stabilising its foundation. The Trevi Group, which is represented by Trevi S.p.A. in the above mentioned Consorzio, has given and is giving its direct and constant contribution and is engaged in supplying the special equipment to the operation and the drilling technology which has been successfully adopted to date.

Jan 1, 2000

By J. Allan Tice

In the past fifteen to twenty years, the use of drilled piers to support high capacities in coastal plain deposits has become more and more common. With improved construction techniques and better understanding of pier behavior, drilled shafts with capacities of 200 to 500 tons are not unusual. The purpose of this presentation is to review several drilled pier installations from North Carolina to north-east Florida as a means of illustrating the different types of design concepts and installation techniques which are presently being used. ACKNOWLEDGEMENTS The information in this presentation was obtained from work performed by many individuals and companies. The section on limestone socket caissons in South Carolina is an abridged version of a paper prepared by Rob Smith and Neil Gilbert of Law Engineering's Charlotte, North Carolina office, and is used with permission. The section on pier installation in northeast Florida is an abridged version of a paper prepared by Kirk Mcintosh, Tom McDaniel, and Randy Knott of Law Engineering's Jacksonville, Florida office, reprinted here with permission. Additional data discussed in this presentation has been obtained from Farr Foundation Company, McKinney Drilling Company, and Peterson Drilling Company.

Jan 1, 1988

By Xu Ronglie

This paper looks back on the developments and achievements of deep foundations, on the basis of the complex geological conditions and environments in China. It sums up advances in theoretical and applied researches, engineering constructions, practical experiences, case histories, and problems and developing prospects of piles and deep foundations in recent years in China.

Jan 1, 1991

By Sam Yao, Ali Naeem, Sara Barrett

Brooklyn Basin Project is a multi-billion-dollar development of the former Port of Oakland 9th Avenue Terminal located along the Oakland Estuary of California. A centerpiece of the development is the 10-acre shoreline park which will be built on a 1,200 ft long by 225 ft wide historic wharf. The wharf was built in the 1930’s on concrete and timber piles with a flat concrete slab. Prior to constructing the wharf, a rock dike was placed to protect the shoreline. The presence of the rock dike increased the hazards from lateral spreading of the underlying bay mud and non-ductile shear failure of piles driven through the dike. To open the park to the public, the wharf required a seismic retrofit in compliance with the California Building Code. The paper presents the results and conclusions of the following topics: • Structural condition assessment and repair strategies for the existing wharf deck, piles and jackets • Application of the California Building Code (CBC Ch31F) for the performance-based seismic evaluation of existing piers and wharves • Nonlinear pushover analysis of the wharf including the combination of inertial and kinematic effects • Impact of rock dike on lateral spreading and kinematic effects and the significance of existing piles in stabilizing the lateral spreading of the rock dike • Retrofit strategies for the wharf to meet the required seismic performance requirements per the California Building Code and reduce the demands on existing piles which were driven through the rock dike INTRODUCTION The 65-acre Brooklyn Basin Development project is located in Oakland, California. The project consists of 3,100 housing units, 200,000 sq. ft of retail and commercial space, along with various parks and public access improvements along the Oakland Estuary. A centerpiece of the development is the 10-acre Shoreline Park which will be built on a 1,200 ft long by 225 ft wide historic wharf. The wharf was built in the 1930’s on concrete and timber piles with a flat concrete slab. As shown in Figure 1, the wharf deck and piles support the 9th Avenue Terminal Building.

Jan 1, 2018

By Richard Deakin

This case study describes aspects of the design of bridge foundations using 320mm diameter steel tube piles in the vicinity of Montréal, Canada. In this area, these piles are a very commonly used and cost effective solution for deep foundations. Typically they are driven through thick Champlain Sea Clay to bear onto stiff, strong rock. However, in some locations there is a layer of glacial till between the base of the clay and the rock which cannot always be fully penetrated by the piles. There is currently little published information, about the bearing capacity of these piles in the local till, and this paper presents and discusses some pile-test data from a recent project. The nature of the glacial deposits in the study area is presented using information gained from published geological data, the project ground investigations and site observations. The design approach and assumptions are discussed, together with the aims and outcomes of preliminary field driving trials and pile tests. The paper then discusses the results of dynamic tests undertaken on production piles. Bearing capacity factors are back analysed from the dynamic test results and compared against values assumed within the design. Observations are made that designers of future foundations in similar conditions may find informative.

Jan 1, 2011

By David Eley

Coastal communities continue to be at risk with sea levels rising. Along these coastal shorelines, vegetated marshes and ridges provide habitat for wildlife and resiliency against storm surge and erosion in low-lying areas. Often, spoils from maintenance dredging of harbors and rivers are placed in confined disposal sites (impoundments), providing little benefit to the environment. Reusing these spoils to restore low-lying marsh areas that are disappearing because of sea level rise, storm damage, sediment deficits, and other natural and manmade processes is growing trend. Design and construction using dredged sediments in a coastal environment can be challenging. It is critical to design and place fill in sensitive habitats in a controlled, thoughtful manner that enhances the environment. Low dikes are often used to contain fill, which is typically excavated and placed using a hydraulic dredge. These dikes are long linear features, often in a marsh environment, and can be difficult to construct. During construction, the project team (contractors and designers) must understand that these are controlled fill projects, with elevation targets and containment requirements. Distribution of sediments to meet project goals typically requires regular movement of the dredge outfall and monitoring during construction to prevent over-topping of containment dikes, and ensure sufficient fill has been placed to meet project objectives. Dredged sediments can be a renewable resource to restore coastal areas when used in projects that are designed and constructed correctly. In this paper, we will discuss design considerations, construction challenges and construction monitoring, including innovative instrumentation, that can help enhance the sustainability and resiliency of low-lying coastal communities.

Oct 7, 2024

By Don C. Warrington

This paper is a survey of the various methods and research efforts by which the drivability of piles is determined. First, a brief outline of the basic theory and the important parameters for driving by vibration are presented. Then, a wide variety of methods by which the drivability of piles is determined are presented and discussed, with special emphasis on methods developed in the USSR. Each of these methods are examined as to how they take into account the various parameters of vibratory pile driving, such as eccentric moment, frequency, dynamic force, motor torque and power, vibrating and static weight, and other variables. Some relation of these methods of field data is presented as well.

Jan 1, 1989