Search Documents

By Thomas G. Tavernaro, Jeffrey A. Schaefer

"The $106 million Olmsted Approach Walls Project, completed in the spring of 2004 by Massman Construction Co., Kansas City, MO, is one phase of a new $1.4 billion Corps of Engineers locks and dam facility located at Mile 964 on the Ohio River, approximately 17 miles (27.4 km) upstream of its mouth at the Mississippi River. When completed, the Olmsted Locks and Dam (Figure 1) facility will replace two aging locks and dams (Locks and Dams 52 & 53) built in the 1920’s, and produce an estimated $600 million annual economic benefit to the nation through reduced lockage time and operation and maintenance costs. PROJECT OVERVIEWThe Olmsted Approach Walls Project consisted of “in-the- wet” construction of four fixed nose pier structures, four floating concrete approach walls, one fixed wall and related underwater excavation, grading and stone placement. Over 12,000 tons (11,000 tonnes) of structural steel and pre-cast concrete elements, up to 335 tons (304 tonnes) in weight, were safely erected during the project.To support these massive structures, the Louisville District of the U.S. Army Corps of Engineers teamed with INCA Engineers, Inc., Bellevue, WA to design thirty seven 10’ (3m) diameter shafts (cast-in-place steel-shell piles) capable of maintaining elastic behavior below ground while resisting barge impact loads, extreme head-on collisions from runaway tows, and environmental forces from river current, wind, and seismic events.The shafts (typically 150’ (45.7m) in length) were founded 100’ (30m) into the riverbed through alluvium, a very consolidated fine sand and clay Cretaceous soil, and finally into a hydrothermally altered rock. Thirty seven shafts were installed under open river conditions at the site, a group of four shafts at each nose pier-pylon location (Figure 2), and 21 at the fixed land wall. Due to difficulty in achieving the required casing tip elevation the team developed a design modification that was successfully implemented for 27 of the shafts.Concurrent with the work at Olmsted, eleven pontoon segments for the four floating approach walls were constructed at a graving yard in Paducah, KY, developed by Massman Construction Company specifically for the project. While the pontoon geometry varied, the pontoons averaged 350’ (107m) in length, 40’ (12.2m) in width and weighed 4,500 tons (4,082 tonnes). The longest of the four walls, at 1,700’ (518m) was comprised of five interconnected pontoons."

Jan 1, 2006

By Desi Dikova, Daniel Wagstaffe, Lori Simpson, Eric Lindquist

1621-1629 Market Street is a mixed-use development in the South of Market district of San Francisco, located directly above Bay Area Rapid Transit (BART) tunnels and alongside the San Francisco Municipal Railway (MUNI) tunnels that run below Market Street. The project included the construction of five new buildings up to nine stories tall, each with single-level basements, supported on improved ground. The project transformed a cluster of commercial buildings and surface parking lots into residential, retail and office buildings, and publicly accessible open spaces. Subsurface conditions at the site include uncontrolled fill, loose sand, and marsh deposits, with groundwater approximately 15 feet deep. Engineering challenges faced during design and construction included: protecting the tunnels beneath and adjacent to the site; the presence of uncontrolled fill, loose sand and potentially liquefiable soil; the phasing of multiple, non-concurrent basement excavations; and construction in a dense urban area, including protection of both on-site and neighboring buildings and other improvements. In addition to Building Code requirements, the project complied with BART’s stringent requirements on loading, settlement, vertical and horizontal movement control, groundwater control, and limiting tieback lengths to provide clearances to tunnels and utilities. This paper reviews these challenges, with a focus on the temporary support of excavation (SOE) systems and the ground improvement. The SOE systems consisted of deep soil mixing (DSM) cutoff walls for four of the buildings and soldier-pile-and-lagging for the other; all were restrained by tiebacks or internal bracing. The DSM walls were incorporated into SOE systems for neighboring buildings with each phase, resulting in efficient shoring utilization. The ground improvement consisted of an interconnected grid of DSM panels that mitigated liquefaction and extended building loads to a dense sand layer. Load testing of DSM elements was performed to confirm adequate bearing capacity.

Oct 7, 2024

By D. Dreher Whetstone, Paul M. Blakita, Christopher M. Reith, Ravi P. Malviya

"Micro-piles are small diameter (5 to 10 inches), cast-in-place piles which can develop high load capacities by bonding with soil or rock. Micro-piles are particularly well-suited for moderate to heavily loaded structures requiring deep foundations in difficult subsurface conditions, such as karst, bouldery mine spoil, or unsuitable fills with concrete debris or other obstructions. Attempts to install conventional deep foundations including driven piles, drilled piers, or auger-cast piles are likely to be fraught with construction difficulties and disputes, delays, cost overruns, and may be unfeasible in some cases. Micro-pile installation equipment is very effective in installing foundations through such overburden or rock materials.This paper presents case histories of Micro-pile installations on two projects with difficult soil/rock materials. The project sites are located in Charles Town, West Virginia and Masontown, Pennsylvania.Charles Town, West Virginia ProjectThe Charles Town project entailed construction of a four-story pre-cast concrete garage. Triad Engineering, Inc. performed a geotechnical investigation for this project (Triad, 2001). The subsurface, geologic, and project specific information described in th is paper are largely based on the aforementioned geotechnical report.Ground ConditionsThe project site is located in Jefferson County, West Virginia, and is mapped to be underlain by the Elbrook Formation. This formation is described as argillaceous, dolomitic limestone with beds of dolomite and aphanitic and algal limestone (Dean, et al. , 1990). The carbonate rocks at the site were characterized as ""moderately solution-prone, highly calcareous and weathers differentially to produce a pinnacled or ""sawtooth"" top of rock profile. (Triad, 2001 )"" Overburden soils consist of low to high plasticity, fine grained residual soils formed by weathering of the parent carbonate rock. The residual soils include variable proportion of sand and rock fragments."

Jan 1, 2005

By Norm Kirk, Robert Bittner

"The addition of a new powerhouse at the existing Tulloch Hydroelectric site on the Stanislaus River in the western foothills of the Sierras Nevada Mountains of central California required a deep excavation in rock on the downstream face of the dam. A cofferdam (water exclusion device) was necessary to isolate the powerhouse construction site excavation from the existing Goodwin Reservoir and the turbulent discharge from the existing powerhouse. The cofferdam was positioned on a steeply sloping fractured rock surface exceeding 50 degrees.This paper describes the challenges encountered during design and construction of the cofferdam and describes the unique design features used to address these challenges including:•,The use of flat-sheet-piles to form cellular walls on the steeply sloping rock surface.•,The use of 5-ft deep tremie concrete plugs in the bottom of the sheet pocket cells to create the bottom seal of the cellular cofferdam walls against the sloping rock surface.•,The use of vertical post-tensioned rock anchors to provide shear resistance at the contact point between the base of the cellular-wall and the sloping rocksurface.INTRODUCTIONModification or expansion of existing hydroelectric power plants often require downstream cofferdams or water exclusion devices to temporarily separate new construction from turbulent downstream discharge of the existing dam. Most dams are positioned on solid rock in the narrowest and therefore the steepest section of the river. This combination of steeply slopingrock and the need for an exclusion barrier creates a challenge for the design engineer trying to maintain a safe dewatered construction site. Typical cofferdam solutions for hydroelectric dams usually use large granular filled circular sheet pile cells that perform as gravity structures. However, this type of structures is not well suited to steeply-sloping highly irregular rock surfaces in a confined area."

Jan 1, 2017

By W. Morgan NeSmith

A drilled displacement pile program was utilized for the expansion of an existing power plant in Cohasset MN adjacent to the Mississippi River. The drilled displacement (DD) pile is an innovative foundation type that provides exceptional value in some geologies. In the U.S., DD piles have typically been used in coarse-grained soils due to the large friction capacities that can be generated by the piles in these conditions. This project was the first large scale experience for the project team where it was anticipated that significant portions of the DD pile capacity would be developed in primarily fine-grained soils. The project site consisted primarily of variable amounts of fill overlying predominantly low plasticity alluvial silts. In some cases, alluvial silty sand layers were encountered within the expected pile installation depths. Alluvial sands were typically encountered below the silts, in some cases within the expected pile installation depths. The project team developed a probe and pile load test program to address the variable subsurface conditions across the site. The program included monitoring various parameters (including applied torque and tool penetration rate) during the drilling portion of the pile installation using recently developed data acquisition techniques. This data was used to estimate the rig energy, or Installation Effort (IE), required for pile installation. IE profiles from the test and indicator piles were compared with subsurface data available from a number of previous site characterizations. Additionally, Cumulative IE values were compared to an in-house database of IE vs. DD Pile Capacity. Final production pile toe levels were based primarily on IE values selected from this comparison. The IE data collected during production was also used to address large variations in pile-cutoff elevation (relative to a fairly uniform ground surface elevation).

Jan 1, 2008

By Timothy Nelson, Simon Burnworth

"The Berkeley Art Museum and Pacific Film Archive (BAMPFA), which currently resides in a 1970s-era post-modern concrete structure just south of the University of California, Berkeley campus, was in need of a new home after an engineering evaluation revealed that the building possessed seismic deficiencies. Pressed for space, the University looked within its portfolio of properties and identified the site of the former University Printing Press facility as the place to build BAMPFA’s new home.The site was perfect; located one block east of bustling downtown Berkeley and its rapid transit station, and directly across the street from the western entrance to the UC Berkeley campus. Thousands of pedestrians pass by the site on a daily basis, thus granting BAMPFA the opportunity to reshape the corner of Center and Oxford Streets with a building that would not only welcome visitors to campus, but also serve as a creative hub for both the City of Berkeley and the UC Berkeley institution itself 1.The original museum plans, drawn up in the mid-2000s, called for complete demolition of the existing abandoned facility and replacement with a visually stunning structure designed by renowned Japanese architect Toyo Ito. Even at this point, the shoring and means and methods requirements of the project were identified as a challenging component, incorporating a shored excavation bounded on three sides by busy city streets and a fourth side by an operating bank and occupied apartment building. Furthermore, a sequenced demolition would be required for the printing press facility’s three-story Administration Building (also known as the Admin Block), one-story printing press warehouse (also known as the Press Building), and an adjacent parking structure. Degenkolb Engineers was retained at that time as the shoring engineer to design the shoring to facilitate this work."

Jan 1, 2016

By Deep Foundation

Whenever an organization launches an initiative, the question arises whether that initiative has staying power. Or is the initiative, as is quite often the case, merely a fad; that is, just an activity that suddenly becomes popular, but which does not stay popular for very long. When the Federal Highway Adminis- tration (FWHA) started its Advanced Geotechnical Methods in Exploration (A-GAME) initiative, that question was addressed, especially considering the fact that up to 50% of major infrastruc- ture projects suffer impacts to schedule or cost due to geotechnical issues. Many of these issues relate to risks identified directly or indirectly to the scope and quality of site character- ization work. Effective site charac- terization is critical for recognizing. potential problems that may affect design and construction and for ensuring safe, well-performing and cost-effective projects. Grounded on that, knowledge of all available site investigation methods should continue to be shared widely and the application of those methods should be encouraged on an ongoing basis throughout the project lifecycle. The A-GAME initiative covers five technologies: Cone penetration testing (CPT), monitoring while drilling (MWD), electrical geophysical methods, seismic geophysical methods, and optical and acoustic televiewers. Of these, three soil and rock investigation methods were highlighted that are underutilized not only here in the U.S., but also in many places around the world: CPT: a well proven and established method for soil characterization that turned 90 last year, in which continuous in-situ data are col- lected quickly and consistently. Geophysics: the science that assesses the physical properties of the soils and rock using seismic and electrical techniques, which con- tinues to advance in leaps and bounds as the application of well- understood technologies become more powerful.

May 1, 2023

By Andrew Moran

In 2021, the University of Pittsburgh began construction of a new recreation and wellness center for students and faculty in the heart of its main campus in Pittsburgh. The design and plans for the center promote the university's goals to create a unique place for members to stay active and to sustainably develop the area within its urban campus. The new 270,000 sq ft (25,000 sq m) center is being constructed within the footprint of two former campus buildings that were demolished, the O'Hara Parking Plaza and the Learning Research and Development Center (LRDC). The recreation center borders O'Hara Street on its south side, the ramp to receiving for the Western Psychiatric Hospital (WPIC) on the west side, an internal campus service road called University Drive A on the north side and a long thin area that will become a new terraced pathway on the east side. The existing site grade ranges from elevation 965-1,058 ft (294-323 m) within the area of the proposed recre­ation center. The ground surface at the site slopes between O'Hara Street in the south upward to the service road in the north with a grade difference of approx­imately 100 ft (30.5 m). The bottom of the excavation for the new center will be near the lowest elevation of O'Hara Street, requiring support of excavation (SOE) on the north (LRDC and O'Hara walls) and west (WPIC wall) sides. Mascaro Construction Company, the general contractor, engaged Nicholson Construction Company for the first stage of the construction, which included existing building demolition, earthwork and SOE systems. Nicholson designed and constructed the SOE systems along the site's north and west sides as described.

Jun 1, 2024

By Paul A. O’Brien, Gary A. Chapman, Thomas G. Cuniowski

"The new Amcor B9 paper mill in Botany, NSW, Australia, involved the design and construction of a new paper mill founded within the Botany Basin Sediments. There were numerous design and construction challenges to address, including tight settlement tolerances for the paper machine footings (6 mm total and 1/2000 mm differential limits), high variable and cyclic loads, deep (>25 m) bedrock and uncontrolled fill material across the site. The mill structure design incorporated a deep driven precast and CFA piled foundation solution, with a comprehensive swathe of testing to validate pile capacity and expected settlements. The pile design for the mill structure included the installation of approximately 1000 piles, with pile testing comprising dynamic testing and a static load test on precast piles. With consideration of Sydney’s increasing demand for development space in relative close proximity to the city’s CBD, industrial areas in the Botany Bay area are likely to make way for heavy or complex commercial and residential structures. Therefore, a better understanding of the engineering behaviour of sediments underlying these areas would allow for efficient foundation solutions. This paper presents a discussion on effective foundation testing techniques and the effects that the behaviour and characteristics of the Botany Bay sediments impose on deep piled solutions.2 PROJECT DETAILS2.1 New paper millThe project involved the construction of the largest recycled paper machine in Australia. The paper machine is 330 m (1080 ft) long, 22 m (72 ft) high, and capable of producing 1.6 km (1 mile) of paper per minute. Construction commenced in early 2011 and new paper mill officially opened in early 2013. The early works contract was awarded to Baulderstone Construction Pty. Ltd. (Lend Lease Corp. Ltd.), with the D&C contract awarded to a consortium headed by Leighton Contractors Pty. Ltd. (CPB Contractors Pty. Ltd.), which included Golder Associates Pty. Ltd. as the geotechnical designer and reviewer.2.2 Site history and effect on local topographyThe site has been used as a paper mill since 1902, and as such, has layers of uncontrolled fill and buried objects within the upper fill materials associated with historical industrial use. The fill material generally comprised of loose and very loose sands, with isolated pockets of cohesive materials, peats, pulped paper and general construction waste. In addition, during construction, underground storage tanks were identified at depth, indicating the historical extent of filling across the site was extensive. The presence of this generally uncontrolled fill was a factor for determining that the most cost effective foundation solution for the paper mill was piled foundations, to bypass these materials."

Jan 1, 1900

By Jeff Wilkinson, Brandon Walter

"A&N Electrical Cooperative provides electrical service to the counties of Accomack and Northampton along Virginia’s Eastern Shore and to Smith Island in Somerset County, Md.A&N recently worked to improve the efficiency of power distribution to a small island community and marina on Tangier Island in the Chesapeake Bay. This improvement consisted of upgrading the existing distribution substation with a new 25 kV 2-bay box distribution structure. Earth Contact Products (ECP) collaborated with PowerServices, Inc. (PSI) to design and install a helical foundation support system as part of the substation upgrade. Feasibility EvaluationThroughout the design process, A&Nworked with its partners PSI (design) andT&D Solutions (installation) to identifycost-effective alternatives. Foundationsystems considered included cast-in-placereinforced concrete caissons, precastconcrete foundations, driven steel piles and helical piles. In evaluating all of theoptions, the greatest concern was gettingthe material onto the island, followedclosely by the availability of the equipmentto install the foundations. Clearly, cost,more specifically the installed cost, was asignificant consideration and decisionfactor throughout the process.There were several limiting factors that had to be considered during the design process, the most significant of which was that all of the material had to be barged to the site. With traditional reinforced concrete deep foundations in mind, the cost for installing these piles was projected to be nearly $2,000/cu yd ($262/cu m) of installed concrete. Given that approximately 5 to 6 cu yd (3.8 to 4.6 cu m) of concrete would be required for this structure, the cost was significantly high for this project. What’s more, because the components of the concrete mix would have to be barged and then hand mixed on site, there was concern regarding both the time required to complete the piles and the quality of the installed concrete. For the driven pile alternative, the availability, or lack thereof, of equipment and material cost resulted in a total cost estimate that was more expensive than that of the concrete piling alternative. The high material cost for the piles, which was more than double than the cost of concrete, was due to the number and size of piles needed to resist the overturning moment. Ultimately, the team selected the helical pile alternative. The decision to a use helical pile foundation system was based on many factors, not the least of which was the remote location of the project site and the difficulties associated with getting material, equipment and construction personnel to the project site."

Jan 1, 2017

By Bengt H. Fellenius

An upgrading and straightening of a highway included building a bridge across a small river. A routine site investigation was initiated to determine the conditions for designing the foundation of the bridge. The proposed bridge was a two-lane highway bridge in one span with a total length of 30 m (100 ft), as indicated in Fig. 1. It was to be placed about 20 m (66 ft) upstreams of the bridge for the existing highway. The site investigation included one boring at each abutment with soil sampling and in-situ vane testing and placed about halfway up the slope from the small river at ground surface elevation + 54 m. Within the investigated maximum depth of 40 m (130 ft), the soils at both borehole locations consisted of a thin clay crust over a thick deposit of soft sensitive clay with a natural water content of about 70 % and a liquid limit of about 60. The undrained shear strength below the crust was about 20 KPa (400 psf) and increased slightly with depth. The sensitivity was high, about 40.

Jan 1, 1987

By Colin Curtis

The City of Manchester is hosting the 2002 Commonwealth Games. A world class Stadium with a 38,000 capacity was commissioned for a site located close to the City Centre. The Stadium location is in an area that was derelict and in need of regeneration and it is envisaged that the Stadium will be the spur for this. The industrial and residential history of the site has left a legacy of buried foundations together with chemically contaminated soils. This Made Ground deposit overlies Glacial Deposits which in turn overlie bedrocks of the Central Manchester Coalfield. Coal mining has taken place from at least 1761 leaving several worked seams and shafts. In order to support the stadium, 1159 conventional augured piles of 600 to 1200mm diameters were used. This paper will deal primarily with the piling operations and testing, but will also discuss the coal seam treatment with respect to piling. A substantial trial pile test programme was carried out together with 11 static load tests on contract piles. The results of the pile tests will be discussed and conclusions drawn.

Jan 1, 2002

By Daniel Ruffing, Jeffrey Evans

Vertical cutoff, or barrier, walls are an integral part of environmental site remediation efforts. Vertical barriers are commonly deployed to limit the influx of clean ground water and/or to control the off-site migration of contaminated groundwater. The level of detailed design consideration devoted to the vertical cutoff wall component varies widely from project to project and generally decreases with decreasing size and complexity. For those projects receiving minimal design effort, conservative design decisions can lead to unnecessary costs or unanticipated conflicts between the various design considerations. In this paper, the authors discuss several important design and construction aspects of vertical cutoff walls requiring particularly careful consideration during the design phase of the project. These design and construction considerations include the need for and extent of excavation for a key, project target hydraulic conductivity, the use of statistical allowances in the specifications, filter press testing, sand content of in-trench slurry, cleaning of the backfill slope, measurement of stress and strain, the additional of slag in cement-bentonite cutoff walls, and longevity of cutoff walls.

By Hiren J. Shah

Across much of New York City, the geology of glacially deposited soils follows a common sequence. Outwash sands generally overlie varved silts and clays, which lie above a basal till deposit underlain by the bedrock. Pile foundations at projects with such typical stratigraphy generally develop their axial capacities by extending below the fine-grained deposits into the till or the bedrock. Contrastingly, at a project site on the Brooklyn waterfront, high capacity piles were efficiently and economically installed by driving them into the relatively shallow glacial drift and till deposits which lay above thick fine-grained compressible glacial lake deposits. An unusual aspect about the foundation design at the Brooklyn project site is that, relatively short and high capacity piles were driven into the shallow glacial drift and till deposits, overlying the thick fine-grained glacial lake deposits. In order for this unusual foundation scheme to be feasible and economical, the piles needed to achieve their driving criteria in the upper strata. Consolidation settlements in the lower stiff and over-consolidated glacial lake deposits below the pile tips had to be relatively small. The paper discusses the unusual stratigraphy in this area of Brooklyn in greater detail with geologic profiles and engineering characteristics of the glacial strata. It also discusses the design aspects of the pile foundations, settlement estimates, a pile drive test program during design, results of the static load test program during construction, and production pile installation results.

Jan 1, 2008

By Christian B. Woods, Joe C. Drumheller

"Kenneth A. Huber, P.E., Langan Engineering & Environmental Services, New York, New York, USAThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. The Prudential Center site encompasses an entire city block that had a varied history of uses ranging from a cemetery in the late 18th century, to a rail yard and train station for the now-defunct Central Jersey Rail Road in the 19th and early 20th centuries, to commercial development in the latter half of the 20th century. Each of these prior uses presented challenges to the design and construction of the Prudential Center that required innovative engineering solutions, including: archaeological investigation and exhumation of the former cemetery occupants, protection of historic buildings surrounding the site, and extensive demolition to remove old train bridge foundations.The design team was required to develop potential foundation systems for the arena. Several foundation concepts were evaluated for cost and constructability, including: driven piles, drilled shafts, and shallow foundations on improved subgrade. Following a detailed cost analysis and value engineering exercise, the decision was made to support the arena on spread footings following the completion of a multi-phased ground improvement program consisting of a combination of dynamic compaction and removal and replacement. To evaluate achievable allowable bearing pressure as part of the design, a dynamic compaction test section was performed within the building footprint prior to the start of production work; this resulted in an increase of the allowable design bearing pressure from 2 tons per square foot (tsf) to 3 tsf. This reduced the expected foundation costs by 30% and gained sufficient time in the schedule to allow for the completion of the arena in time for the New Jersey Devils 2007- 2008 hockey season.BACKGROUNDThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. After several years of negotiating between the City of Newark, local landowners, area developers, and the Devils themselves, a deal was finally struck to erect Newark Arena, now known as the Prudential Center, right next to City Hall. This is not to say, however, that once the site location was finalized, that no further challenges were encountered in the construction of Newark’s new crown jewel."

Jan 1, 2015

By Daniel W. Mageau, Larry W. Applegate, Aaron K. McCain

"An innovative method of ground freezing was successfully tested to create a “dry” excavation condition for a new building foundation at a site in downtown, Miami, Florida. The subsurface conditions in Miami generally consist of very porous, weak limestone and sand with groundwater near the surface. Water flow through these materials can be very high. Dewatering is extremely restricted in Miami so deep below-grade structures are rare and expensive. A new, innovative method to allow deep excavations in dry conditions without dewatering involves the creation of a thick, temporary, frozen soil plug below the planned excavation depth across the entire site to cut off vertical groundwater flow during construction. Frozen soil is impermeable and very strong and has long been used for temporary structural and water-tight shored walls. Using the same proven principals, frozen soil plugs are very effective at cutting off water from the bottom of the excavation as well as resisting upward buoyant forces. This new freezing method can be used for fairly deep excavations in new building construction supported on deep foundations. The building piles act as temporary anchors for the frozen plug to resist very high upward buoyant pressures until the permanent structural slab is completed.IntroductionUnlike other Cities, below grade basements are rare in Miami. The few basement foundations constructed have utilized a cumbersome and expensive method of excavation and shoring involving underwater excavation, tremie slabs, and commercial divers. The key issue for underground construction in this area of the country is the vertical flow of groundwater through the base of the excavation. To deal with this issue in the past, the contractor first installed all of the building piles and the perimeter shoring walls. Then, interior sheet pile walls are installed to create small manageable excavation pits. Each pit is then excavated through standing water “in-the-blind” and around the buildings support piles. The final excavation, interior struts, and inspection is performed by commercial divers. Finally a thick foundation tremie slab is poured under water. This method could be successful but proved to be time consuming and expensive. In addition, some building piles were occasionally damaged during the under-water construction process."

Jan 1, 2015

By Paul J. Sabatini, Robert C. Bachus, Terence P. Holman, Panos Andonyadis

A recent landslide comprising approximately 12 acres (4.86 hectare) and a displaced volume of more than 500,000 cy (382,000 m3) caused the shutdown of a four-lane state highway and two high-capacity freight railway lines. After completion of immediate landslide stabilization activities, various long-term slope stabilization measures were implemented that focused primarily on gradual slope unloading in areas near and upslope from the scarp of the landslide. Near the completion of the upslope excavation, an anchored soldier beam and lagging wall was constructed to allow for the temporary unloading of the toe of the main landslide area to facilitate installation of a permanent underdrain. The design of the anchored wall utilized information collected during the rehabilitation construction and included inclinometer data, site survey results, piezometer data, and field construction observations. Using the history of site-specific movements, results of back-analysis calculations from the landslide, and geometry/performance of the post-construction slope configurations, the fully softened and residual shear strengths along two potentially critical sliding surfaces were calculated. Owing to the high confidence in the values of shear strength as afforded by this information, the confidence in local groundwater conditions, and control of the loads, the designers selected a relatively low, calculated short-term factor of safety (FS) (i.e., FS ˜ 1.1 to 1.2) for the most critical unloading step. Long term calculated FS values on the order of 1.2 to 1.3 were anticipated. This paper describes the detailed evaluation of the landslide slope movement data associated with the shallow and deep potentially critical failure surfaces and selection of the associated values of design shear strength for these potentially critical surfaces. A description is presented of the analyses and design of the anchored wall, measures implemented during construction to minimize slope movements, and post-construction monitoring results during the unloading and subsequent installation of the underdrain.

Jan 1, 2017

By Scott A. Walker, Gabriel J. Alcantar, Brian Zuckerman, Ramin Golesorkhi

"The stadium development consists of construction of a 68,500-seat, open-air NFL football stadium for the San Francisco 49ers. The main structure will consist of a 7-story above grade steel structure supported by over 3,000 piles. Berkel and Company Contractors, Inc. (Berkel) was selected as the design-build pile contractor who used their auger pressure grouted displacement (APGD) piles for this project. During an indicator pile installation and pile load test program, fifteen piles were tested to develop installation criteria to support demands of 150kips tension and 180 kips compression. Following the indicator pile program Berkel installed 3088 piles in 30 working days. Throughout pile installation data were collected with an automated data acquisition system (DAS). During pile installation field engineers from Treadwell & Rollo observed the pile installation as well as the real-time data from the DAS. Strategic staging and pre-production planning by Berkel along with consistent collaboration with the design team created an atmosphere for a successful and on schedule project completion.IntroductionThe new San Francisco 49ers Stadium in Santa Clara, California will be a 68,500-seat facility, a rendering of which is shown in Figure 1. The main structure will consist of a 7-story above grade steel structure supported by more than 3,000 piles. The north, east and south portions of the stadium are designed as an open seating bowl, while the western portion includes open seating at the lower levels and seven-story tower which houses over 150 suites.The stadium project includes the stadium structure, as well as elevated open pedestrian walkways, commercial community space, and three new pedestrian bridges spanning a nearby by creek. Sustainable designs and innovations such as a green roof, photovoltaic panels, a ground source geothermal system, stadium-wide Wi-Fi capability, and access to public transit are provided throughout the project. The stadium is designed as an open, light, and airy structure and is surrounded by an existing amusement park, office buildings, the Santa Clara Convention Center, and the training facility of the 49ers."

Jan 1, 2015

By James F. Davis, Matthew A. Conte, Robert F. Tonning

This is a paper demonstrating the steps taken to combine multiple types of piles for a single site to maximize the benefits and characteristics of each method. We intend to discuss the use of grouted displacement piles in lieu of traditional pile types that were specified on an individual project. We will show how implementing this alternate pile type can both supplement and replace the originally specified pile to increase efficiency and lower costs. We will demonstrate a reduction in spoils, vibration, crew hours, and equipment size while employing methods to overcome unforeseen ground conditions.

By Seth H. Hamblin, Leo J. Hart, John E. Regan

The Route 6 /10 10 Interchange Design/Build project, located in Providence, Rhode Island, involves the design and construction of five (5) new elevated bridge structures to replace and reconfigure the existing interchange and to provide a link between Route 10 northbound and Route 6 westbound. Due to site logistics, headroom restrictions, and depth to bedrock, 50 ton drilled micropiles installed in the deep medium dense sand strata were initially proposed as the deep foundation solution. Post project award, Geosciences Testing and Research, Inc. (GTR) performed various analyses and developed an alternate driven pile solution using steel Tapertube. The results of these analyses indicated that driven steel taper tube and steel pipe piles could develop greater capacities than the drilled micropiles in the granular soil layer, thereby reducing the number of foundation elements, decreasing construction schedule and providing a more cost effective foundation alternative. A comprehensive driven pile load test program was subsequently executed by GTR and the Design Build Team led by Barletta Heavy Division of Canton, Massachusetts, to assess the performance of Tapertube and steel pipe piles, including pile drivability, load-deformation characteristics under static and dynamic loading, and to develop site-specific design parameters in two (2) distinct test areas. The test pile program included dynamic, static compression, tension and lateral load tests on each test pile. Load test measurements were automated with embedded Vibrating Wire Strain Gages (VWSG) to measure load transfer with depth. The execution and results of the successful pile load test program are presented and offer unique case study and valuable data for the use of Tapertube piles on deep foundation projects in the New England region INTRODUCTION The Rhode Island Department of Transportation (RIDOT) Route 6 / Route 10 Interchange is located west of downtown Providence. Originally constructed in the 1950’s as a highway bypass around the historic Olneyville neighborhood, the interchange consists of a series of nine (9) bridges and ramps that serve as a vital east-west link between Interstate 295, 95 and 195. Based on recent bridge rating assessments, seven of the nine bridge structures are rated “structurally deficient”. With many bridge structures shored with temporary supports as many as 15 years ago, the interchange is in critical need of replacement. In 2018, RIDOT awarded the Route 6/10 Reconstruction Design-Build Project to 6/10 Constructors, Joint Venture. Led by Barletta Heavy Division of Canton, Massachusetts, the Design Build team includes O&G Industries, DW White Construction, Aetna Bridge Co. and AECOM. The scope of work includes the replacement of the bridges and ramps, and will provide direct access from Route 10 northbound to Route 6 westbound. Valued at over $400M (US), this is currently the largest project awarded in RIDOT history.

Jan 1, 2019