Search Documents

By Wei Ye, Lei Li, Xianjian Guo, Feng He

The purpose of the paper is to study the smelting process of copper concentrate with high Cu/S ratio produced in Africa or other areas around the world and theoretically analyze the influence of slag type on the smelting process. The paper has compared the processes used successfully in smelters, including CAPEX and OPEX and other factors, to provide reference for the industry to select the best process under specific conditions. INTRODUCTION At present, a great amount of copper concentrates with high Cu/S ratio, with chalcocite being the major source of copper, have been produced or are about to be produced in the Copperbelt in Africa and other countries in the world. The copper concentrate is usually high in copper (~30–55wt.%) and low in sulfur (~10–15wt.%). The conventional processes of smelting-converting and roasting-leaching-electro-winning for treating this type of concentrate is high energy and materials consumption such as electric power\fuels\flux et al. The direct-to-blister (one-step) smelting process can be considered favorable due to a reduction in processing steps. Up to now, there are four copper smelters in the world operating with the direct-to-blister smelting process. There certainly are problems in the process such as high copper content in the slag, strict operation requirement of slag cleaning electric furnace, etc. Except technical issues, the impact of factors on economical aspect such as power and material cost needs to be considered comprehensively in process selection. In this paper the technical issues of direct-to-blister smelting process, including slag treatment process, were analyzed and the comparison to the conventional processes and economic analysis of direct- to-blister smelting process to treat high Cu/S ratio concentrate were done.

Jan 1, 2019

By David L. Huston, Wouter Bleeker, Bruce E. Taylor, Ron Cook, Bob Stewart, Elizabeth R. Koopman

"Abstract—Detailed oxygen isotope mapping of rhyolites in and around the Kidd Creek mine indicates that the orebodies are associated with relatively low (<12‰) whole rock values that extend up to 200 m laterally from ore. The zone of low d18O values is overlain stratigraphically by a carapace of higher (>13‰) values that extends up to 1.5 km laterally from and 300 m to 500 m above ore. Immediately above the stratigraphically highest orebody this carapace is cut by a zone of lower d18O values extending from the ore zone. Zones of higher d18O values also occur in massive rhyolite bodies that occur in the footwall of the orebodies.The zone of low d18O values partly coincides with a Na2O depletion anomaly associated with hydrothermal alteration, except that the Na2O depletion anomaly has a greater lateral extent, and the low d18O anomaly extends farther into the stratigraphic hanging wall. These data suggest that d18O mapping may detect hanging wall alteration above massive sulfide bodies more effectively than conventional lithogeochemistry. Zones of high d18O values, which define zones through which large quantities of low-temperature hydrothermal fluids have passed, may also have usefulness in exploration.Oxygen isotope variations at Kidd Creek record three stages of a hydrothermal system that evolved in temperature with time, as follows: (1) an early, low-temperature event that produced rocks with high d18O values, (2) a high-temperature event that produced rocks with lower d18O values, and (3) a later, low-temperature event that also produced rocks with high d18O values. The high d18O signature of the massive rhyolite was recorded during early-stage, low-temperature (<200°C) alteration, and was probably preserved owing to decreases in permeability associated with low-temperature silicification. The low d18O signature of cherty breccia and chloritite was recorded during the thermal peak at >300°C. High d18O values in the carapace above the deposit were recorded as the hydrothermal system waned."

Jan 1, 1995

By Carlos Rebolledo, Nelson Parra

Arsenic is an unresolved problem in the mining industry considering the fact that most of the new copper deposits have high arsenic contents; stricter environmental restrictions for handling, transporting and processing complex materials are expected and stable abatement of arsenic is not extensively applied. In 2018 Chile produced 24.5% of the total copper from concentrates and in the future copper production in Chile is expected to increase, mainly associated with production of concentrates that will also contain more arsenic. China has set an import benchmark of maximum 0.5% for arsenic content in copper concentrates and this value is expected to be more restrictive in the future. On the first day of 2018 China banned the importation of scrap. Blending practice has been a business option, but it is not sustainable in the future, as “normal” copper concentrates become less and less clean. By the end of 2018, Chile formulated new regulations, increasing the capture of SO2 and arsenic to 95%. In order to comply with these regulations Chilean smelters had to make large invest large amounts of money. Disposing of arsenic as a stable residue is a pending issue. EcoMetales is a 100% subsidiary of Codelco and provides the mining industry with environmental solutions. It has a plant near Calama in Chile that treats flue dust from smelters, refinery effluents and acid solutions from acid plants. EcoMetales is fully committed to contributing to the solution to the arsenic problem. Currently we are developing four main projects: 1) Concentrates treatment. A PLCC project considering the treatment of 200 ktpy of copper concentrates with arsenic from the northern district of Codelco; 2) EPAS DET project considering the treatment of 700 m3/d of weak acid solution with arsenic from the of El Teniente devision of the Codelco acid plant; 3) Borras project, considering the recovery of valuable metals (Cu, Ag, Ge, Pb) from the flue dust leaching plant; 4) Tailings project, considering the recovery of metal values from tailings. The purpose of this work is to present the trends and treatment processes for arsenic handling in the copper mining industry with a focus on the scorodite process. INTRODUCTION Between 2000 and 2015 the global copper concentrates production has grown from approximately eleven to fifteen million metric tons per year. Chile produced 26.5% of the total copper from concentrates and in the future copper production in Chile is expected to increase, mainly as a result of the production of concentrates (Figure 1)

Jan 1, 2019

By J. Bruce See

INTRODUCTION This symposium at Cu 2019 has been organised to honour and celebrate the career and achievements of Dr Phillip John Mackey, an internationally recognised expert in the production of non-ferrous metals, especially copper and nickel smelting and refining. Phillip was born in Epping, a suburb of Sydney, New South Wales, Australia on 19 April 1941 and is one of 4 children of Gilbert and Philomena (nee Bartlett) Mackey. After completing Primary School in Epping, he attended Marist Brothers High School in Eastwood, Sydney and graduated in 1957 as the Dux of the School. Phillip’s father, being on the staff of the Sydney Technical College, in Ultimo, Sydney had the opportunity in the early 1950s to meet the late Professor Sir Rupert Myers, Foundation Professor of the School of Metallurgy at the New South Wales University of Technology (later called the University of New South Wales or UNSW). Gilbert Mackey was impressed by the new young Professor of Metallurgy and encouraged his son to study metallurgy - at the time an expanding industry in post-war Australia. EDUCATION AT THE UNIVERSITY OF NEW SOUTH WALES Phillip commenced at UNSW in 1958, graduating with honours in 1963. His undergraduate education and training included a few years of part-time study while working at British Motor Corporation on sheet metal forming of car bodies. At University Phillip developed his talent for teamwork. He was a contributing writer to the University newspaper, Secretary of the UNSW Students’ Union and was active in the UNSW Metallurgical Society and co-editor in 1963 of “Metallurgical Review,” the annual journal of the UNSW Metallurgical Society. His diverse interests and curiosity about the world around him were likely nourished while at University. Upon completing his Bachelor’s degree, Phillip was awarded a Commonwealth of Australia Postgraduate Research Scholarship. He began his PhD in 1964 on the thesis topic “Studies in Heat Transfer between Dispersed Liquid Metals and Gaseous Atmospheres” working under the supervision of then Associate Professor Noel Warner, an outstanding Professor at the University. Professor Warner is now an Emeritus Professor at the University of Birmingham and is internationally respected for his pioneering theoretical and practical work on established and innovative smelting processes.

Jan 1, 2019

By Xuanxue Mo, Zengqian Hou

"Yidun Island Arc in Sanjiang Region is one of the important Kuroko-type volcanogenic massive sulfide deposits (VMS) districts in southwestern China. Tectonically, the region is situated in the eastern portion of the Tethys orogenic belt, and is a late Triassic extensional island-arc. The island-arc underwent earlier arc construction, intra-arc rifting, later arc construction and backarc spreading during its evolution and formed a complete trench-are-basin system, i.e., the Ganzilitang suture zone, forearc basin, outer are, intra-arc rifting zone, inner arc and back-arc basin from east to west across the island-arc.Kuroko-type VMS deposits and occurrences discovered so far are limited to within the intra-arc rifting zone of the Yidun Island Arc and tend to occur in groups or clusters distributed in separate faultbound basins; e.g., Zengke, Gacun and Xiangcheng basins, in which submarine volcanic rocks, especially bimodal volcanic suites, were extensively developed. The VMS deposits formed in the waning stages of volcanic eruption in the late Triassic and are hosted in the uppermost section of acidic volcanic rocks (rhyolitic-dacitic) within a bimodal suite. The orebodies are associated with these host rocks: rhyolitic-dacitic pyroclastic rocks and exhalites and chemical sedimentary rocks.All VMS deposits in Sanjiang are of the Zn-Pb-Cu type. The architecture of the deposits is twofold, consisting of concordant lenses and layers of massive sulfides and an underlying discordant stockwork. All deposits show metal zoning. The hydrothermal alteration related to mineralization is strong and asymmetrical, and is found dominantly within the stockwork zone and host rocks surrounding the ores. There are two alteration patterns: (1) chloritization - sericitization - silicification from outer sides to core of the alteration pipe; and (2) silicification + sericitization - silicification + carbonate from the lower to upper part of the alteration pipe.The mineralization temperatures of ore-forming fluids vary in the range 200°C to 335°C. Thermal evolution of the fluids displays temperature profiles that first increase and then decrease with progression of mineralization processes. The majority of black-ore minerals (Groups I and informed during intensifying stages of hydrothermal activity, and the majority of semi-yellow-ore minerals (Group III) formed during a thermal maximum. There followed the formation of fine-grained black-ore minerals (Group IV), which interacted with barite layers during decreasing temperature phases.Oxygen and hydrogen isotope studies show that the sources of ore-forming fluids for the Kurokotype VMS deposits are two-fold: seawater and magmatic hydrothermal solutions, represented by the Kuroko deposits in Japan and Kuroko-type VMS deposits in Sanjiang, respectively. In the latter case the hydrothermal solutions reacted with host rocks and mixed with cold seawater percolating downward, and circulated through volcanic rocks resulting in development of alteration zones and formation of ore minerals in Kuroko-type VMS deposits."

Jan 1, 1993

By S. Shokri

The increasing size and complexity of mega construction projects result in having several geographically distributed stakeholders, collaborating with each other to successfully deliver the project. Electronic Product and Process Management Systems (EPPMS) are recently emerging to facilitate the collaboration between stakeholders, reduce the surprises and issues, and improve the project productivity. These are commercially successful but evolving systems. An important component of EPPMS is the Interface Management System, which aims at formalizing and automating the communication channels between stakeholders. An interface is generally considered the link between construction elements, phases, or stakeholders. An interface Management System (IMS) involves five iterative steps: (1) Interface Identification, (2) Interface Documentation, (3) Interface Transferring, (4) Interface Communication, and (5) Interface Closing. A fundamental part of step 2 is recognizing different roles in dealing with interfaces. Each stakeholder is assigned a different role, such as responsible, accountable, consulted, and informed. In a mega project, several thousands of interfaces exist with complex relationships between stakeholders. Therefore, identifying stakeholders with higher responsible roles has been requested as useful information to the project owner in dealing with some of the project risks. After the interfaces are determined, and the responsibilities are allocated, the critical stakeholders are identified using the centrality concept in Social Network Analysis. The critical stakeholders can be determined at the highest level, considering all types of interfaces, as well as for each specific type or discipline-related interfaces. The proposed methodology is applied on a hypothetical offshore project with over 500 interfaces. In fact, this project is a simplified representation of a real scale Liquid Natural Gas project. In order to reduce the complexity of calculations and clarity of explanations, the simplified case study is used. By implementing IMS in mega projects, different parties not only formalize the communication between each other, but also gain better visibility concerning their roles and responsibilities. In addition, the owner benefits from analysing the complex relationships between stakeholders to further identify critical ones, along with other criteria like package cost, stakeholders? experiences, etc.

Aug 1, 2013

By Daniel Hodouin, Mélanie Proulx, Claude Bazin

"Collector and frother are commonly used to induce the floatability of valuable minerals in flotation plants. These reagents are usually distributed down a flotation bank or sometimes added in a single location at the top of the bank. A review of the literature and some experimental results obtained from laboratory and full scale trials indicate that the way flotation reagents are distributed down a flotation bank may influence the flotation response of coarse particles. The paper summarizes these observations which show that the distribution of reagents is a potential tuning variable for process optimization.IntroductionFlotation is in many cases the only way to concentrate sulphide and some oxide minerals. Flotation is a concentration process that uses particle surface composition to induce the selectivity by mean of hydrophobic reagents. The influence of particle size on flotation was firstly analyzed in the 50's1·2 and intensively investigated in the 70's, early 80's and 90's3-18. Most of the observed results show the existence of an optimum flotation size range9 whose recovery is not significantly influenced by a reduction of collector dosage""18. This result brought the idea of using a small portion of the total collector dosage at the top of a rougher bank and to distribute the remaining through the end of the bank to ensure sufficient collection of the coarse particles that need more hydrophobic coverage to attach to air bubbles and be lifted to the surface.This paper discusses the idea of using the distribution of reagents down a flotation bank to tune the operation of the process. Unlike the literature on the effect of reagents (collectors, frother...) dosage that is dense, little attention has been put on the distribution of reagents in a flotation bank. Although research on this subject has not been pushed very far, some operators have recognized the potential of a strategic addition of reagents down a flotation bank19. Except for a few exceptions, the proportions of the reagents to be distributed down a flotation bank are decided according to operator's experience instead of process analysis in relationships with particle size. This paper recalls observations made by different researchers that lead to the idea of using the distribution of reagents as a tuning variable for the flotation process. The paper does not present a detailed analysis or optimization scheme for tuning the distribution of reagents, but analyzes some plant and laboratory results with a view toward the development of a testing methodology and ultimately a validation or rejection of the idea."

Jan 1, 1998

Heap leaching accounts for around 20% of the global production of copper. In heap leaching coarsely crushed ore particles are contacted with an aqueous lixiviant percolating through large packed beds (heaps) of the ore particles, with the loaded solution collected at the foot of the heap for metal recovery, solution make-up and recycle. While dominant for copper oxide acid leaching, it finds application also in copper sulphide (bio) leaching. Despite their apparent simplicity, heaps are in fact complex chemical reactors in which a number of competing sub-processes determine the overall rate of metal extraction. Therefore, meaningful prediction of copper production rates from heaps, as well as operational optimisation and control, all hinge on a comprehensive and quantitative understanding of these complexities. The paper gives a comprehensive overview of the various sub-processes in copper heap leaching and their interactions, including those relating to mineral-particle-solution-gas phase interactions at the micro-scale bulk transport and distribution of solution in unsaturated dense beds at the macro-scale. On the basis of a more fundamental understanding and modelling, the potential for optimized operation offers new opportunities for the extraction of value from both low-grade and complex polymetallic ores. INTRODUCTION Heap leaching is one of the percolation leaching technologies, which includes in situ leaching, dump leaching, heap leaching and vat leaching (Bartlett, 1998). The common phenomenon in all these technologies is the transport of leach solution through a fixed bed of ore particles, which interacts with the solid as it migrates along its path. The target minerals are released into solution and with its flow are carried out of the bed. The targeted dissolved metal species are recovered from solution through various hydrometallurgical techniques, especially solvent extraction (SX), before the barren solution is returned to the leach process. Heap leaching is practised in three main types of applications: sulphuric acid leaching of copper oxide ores, cyanide leaching of gold ores as well as the oxidative acid leaching of secondary copper sulphide ores, usually with the assistance of certain microorganisms and, more recently, in the presence of chlorides (CaCl2, sea water). While gold heap leaching dates back to the 1960s, large scale copper heap leaching commenced in Chile from the 1980s, and sulphide heap leaching emerged essentially as a consequence of acid leaching from mixed oxide/sulphide ores from the 1990s (Watling, 2006).

Jan 1, 2019

By Garth D. Kirkham

The Problem The Don deposit is a series of two sub-vertical zones that pose a number of challenges with respect to modeling and interpolation. The first challenge is that, based on data and observations, the mineralization and, more importantly, the grade is layered or banded and is stratigraphically controlled. The second challenge is that, due to the undulations of the deposit and extreme changes in dip, using a standard oriented ellipse to guide the estimation process is not appropriate and does not result in an estimate that is representative on a local scale. In order to solve this problem an adapted methodology of relative elevation modelling, has been devised to effectively model and estimate deposits faced with these challenges. Relative Elevation Designed for bedded seam and gridded surface With variable dip and vertical grade variability

May 1, 2013

By I. Mc Dougall, H. Joubert, G. de Villiers

The use of sidewall copper cooling systems to prolong furnace campaign life is becoming an accepted technology solution in the base metals industry. Tenova Pyromet has designed and installed a number of sidewall copper cooling systems in base metals furnaces, including the platinum industry. Apart from increasing the furnace campaign life through the formation of a stable freeze lining, a well-designed copper cooling system enables the plant operator to focus more on optimizing the process to achieve throughput and recovery targets, and to accommodate more varied and available concentrate feed blends. The paper discusses the design of sidewall copper cooling systems for copper smelting and converting furnaces to achieve the above objectives. More specifically, the design of copper cooling systems for top submerged lance furnaces are discussed. An overall increase in furnace heat losses has been raised as a concern for intensively cooled sidewalls. The paper explores the overall heat loss expectations for copper cooled furnaces versus traditional refractory lined furnaces. In addition, the potential use of alternative cooling media is discussed. INTRODUCTION Base metal smelting and converting furnace technologies have been evolving continuously over the past century to satisfy the need for higher throughput, improved efficiency, and longer campaign life. To accommodate these demands, in particular higher smelting intensity and throughput, furnace bath containment systems had to improve. The use of pure refractory lining systems has slowly made room for the use of more intensively cooled lining systems (Joubert, Nikolic, Bakker & Mc Dougall, 2016). These cooling systems evolved from external shell cooling, such as shower or film cooling, to copper plate coolers extending into the furnace refractory lining, and high intensity stave or panel coolers (Verscheure, Kyllo, Filzwieser, Blanpain & Wollants, 2006). Consequently, an increasing number of base metal smelting and converting furnaces are equipped with copper cooling systems, including flash furnaces (Bryk, Ryselin, Honkasalo, & Malmstrom, 1958; Yasuda, Motomura & Kawasaki, 2014; Marx, Shapiro & Henning, 2010), top submerged lance primary smelting and fuming furnaces (Bhappu, Larson & Tunis, 1994; Kim, Lee & Lee, 2000; MacRae & Steinborn, 2018), top submerged lance converting furnaces (Viviers & Hines, 2005; Nikolic, Hogg & Voigt, 2018), primary platinum smelting electric furnaces (Nelson, Stober, Ndlovu, De Villiers & Wanblad, 2005; Jones, 2005; Hundermark, De Villiers & Ndlovu, 2006; Mc Dougall, 2013), and electric slag cleaning furnaces (Joubert, Nourse, Masters & Hundermark, 2005).

Jan 1, 2019

By M. Silva, G. Olivares

In a leach pile, the drainage layer or commonly known as the cover layer has been a matter of discussion due to the multiple phenomena or events that occur within it which impacts negatively the leaching process. All these events are directly related to the loss of draining capacity and irregular flow net due to an excessive compaction and entrapment of fines reducing the flow velocity which in turn cause more fines to get trapped. Over time the problem will continue to worsen rapidly and accelerating continuously like a geometric progression. When the cover layer gets to a certain level of deterioration, the only alternative to continue operating safely is to replace the entire cover material, a huge cost for any mining operation. TESRA has developed a solution to counteract the accelerated advance of the deterioration of the drainage layer. The solution consists of using large agricultural tractors coupled to a proprietary design of a heavy- duty subsoiler-ripper for deep tillage for loosening and breaking up the ground at various depth and with different legs spacing from 0.4 m or above. Also, if the ground still requires additional breaking, TESRA proposes the use of a rototiller that breaks any lumps to homogenize the ground to a certain particle size. With the subsoiler-ripper/rototiller combination equipment a layer of 0.5 m deep is properly treated to match closely the original conditions of the ground thus regaining the flow net as close as to the original seepage condition. Once the ripping is completed the subsoiler-ripper tool is replaced with another that is similar to a plow and thus continue with the installation of drainage pipes. The tool digs a Y-type profile trench allowing the pipe to sit precisely at the bottom of the trench, contributing additional lateral and lower support. This tool controls the installation depth of the drainage pipe at different inclination grades and also eliminating any irregularities that may block the flow of the leaching solution. Sometimes the obstructions block completely the flow of the solution. The main result of this methodology is the reduction of groundwater levels and at least 2% less humidity in the leaching gravel due to an increase in the draining capacity of cover. The methodology developed by TESRA applied during a couple of cycles of a dynamic leach pile has proven to be a real alternative to remedy and recuperate the cover close to its original conditions. The methodology requires only one large tractor and two accessories operated in different stages while replacing the more traditional and less efficient machinery such as the Bulldozer, Motor-grader, and backhoes.

Jan 1, 2019

By David L. Huston, Wouter Bleeker, Bruce E. Taylor, Ron Cook, Bob Stewart, Elizabeth R. Koopman

"Abstract-Detailed oxygen isotope mapping of rhyolites in and around the Kidd Creek mine indicates that the orebodies are associated with relatively low (<12‰) whole rock values that extend up to 200 m laterally from ore. The zone of low d18O values is overlain stratigraphically by a carapace of higher (>13‰) values that extends up to 1.5 km laterally from and 300 m to 500 m above ore. Immediately above the stratigraphically highest orebody this carapace is cut by a zone of lower d18O values extending from the ore zone. Zones of higher d18O values also occur in massive rhyolite bodies that occur in the footwall of the orebodies.The zone of low d18O values partly coincides with a Na2O depletion anomaly associated with hydrothermal alteration, except that the Na2O depletion anomaly has a greater lateral extent, and the low d18O anomaly extends farther into the stratigraphic hanging wall. These data suggest that d18O mapping may detect hanging wall alteration above massive sulfide bodies more effectively than conventional lithogeochemistry. Zones of high d18O values, which define zones through which large quantities of low-temperature hydrothermal fluids have passed, may also have usefulness in exploration.Oxygen isotope variations at Kidd Creek record three stages of a hydrothermal system that evolved in temperature with time, as follows: (1) an early, low-temperature event that produced rocks with high d18O values, (2) a high-temperature event that produced rocks with lower d18O values, and (3) a later, low-temperature event that also produced rocks with high d18O values. The high d18O sig- nature of the massive rhyolite was recorded during early-stage, low-temperature (<200°C) alteration, and was probably preserved owing to decreases in permeability associated with low-temperature silicification. The low d18O signature of cherty breccia and chloritite was recorded during the thermal peak at >300°C. High d18O values in the carapace above the deposit were recorded as the hydrothermal system waned."

Jan 1, 1995

By Xuanxue Mo, Kaihui Yang

"The Laochang mine, located in the Sanjiang area of southwestern Yunnan Province of China, is a volcanogenic massive Pb-Zn-Cu sulfide deposit. It is hosted by a pyroclastic sequence of Early Carboniferous age, namely the lower member of the Yiliu Group, which was intruded by syenite and rhyolite porphyry. The volcanic suite is basaltic or basaltic-andesitic in composition, has alkaline affInities, and is associated with the initial rifting along the margin of the Baoshan-Shanstate continental microplate (Yang, 1989). The ores are typically Pb>Zn>Cu in composition, averaging 3.820/0 Pb, 3.51% Zn, from 0.01% to 1.85% Cu (0.107% av.), a high average content of Ag (113 glt) and recoverable amounts of Au, n, Gd, Ga, Ge, In. A massive sulfide zone, in which lenticular and stratiform orebodies are localized in a sulfide-<:arbonate-silica shale unit or sulfidic tuffIte horizon that usually overlies coarse-grained pyroclastic rocks, is underlain by a stringer sulfide zone developed in a subvolcanic intrusion or volcanic sequence. The sulfIde mineral assemblages, from the top to the bottom of the deposit, are: realgar + orpiment - galena + sphalerite + pyrite - chalcopyrite + pyrite + pyrrhotite + arsenopyrite. Oxide and sulfate minerals occur rarely in the massive ores. The massive ores are generally fme-grained and banded, but coarse-grained ore, colloform and framboidal texture, and growth-zoned pyrite and sphalerite are common. Sedimentary features such as graded bedding, brecciated and deformed ore clasts, and chaotically emplaced blocks, are well preserved, indicating that the massive orebodies have undergone slumping and displacement. Alteration is weak in the hanging-wall rocks, but strong in the stringer zone. Two distinctive alteration zones have been identifIed: the upper zone, characterized by an assemblage of quartz, carbonates, chlorite, albite, zeolite and sericite, and the lower zone containing diopside, tremolite, actinolite, gamet, clinozoisite, and epidote.The general features of the Laochang deposit are in accord with the descriptive model of VMS deposits (Lydon, 1984). However, it falls into neither the Zn-Cu group nor the Zn-Pb-Cu group chemically (Franklin et al., 1981). The depositional setting of the Laochang deposit is quite different from Cyprus or Besshi-type massive sulfide deposits. Laochang is hosted by alkaline lavas that were erupted in a submarine continental rift. Although some features of the Laochang deposit are similar to those of Kuroko-type deposits, there are remarkable differences in the alteration mineral assemblage, the proportion of ore-forming elements (lead enriched) and the amounts of oxides and sulfates. These suggest corresponding differences in ore fluid composition and the associated ore-forming environment. Thus, the authors suggest that the Laochang deposit may be a distinct type of VMS deposit."

Jan 1, 1993

By G. Heinrich

Size by size recoveries and pentlandite liberation data from image analysis were used to evaluate plant tests of pentlandite flotation and pentlandite/pyrrhotite middlings flotation from pyrrhotite in a circuit treating low grade magnetic intermediates at the Strathcona Mill. Raising the pH with lime gave improved selectivity for liberated pentlandite but there were major losses of middlings unless the circuit was pulled hard indicating the need for finer regrinding. However, size by size recoveries at the normal regrind showed that, while the pentlandite recovery improved in the finer ranges, the pyrrhotite recovery also increased leading to little selectivity in any size range. A much finer regrind gave greatly improved selectivity in all size classes suggesting that 'surface polishing' as well as liberation effects were being seen. Using liberation data from image analysis of the products, surface polishing accounted for over 99 % of the improvement in selectivity. Unreasonable recoveries of more highly liberated particles were observed for liberation analysis by volume fraction but showed the expected trend in recovery when the analysis was based on surface liberation. The surface liberation data showed that the improved pentlandite recoveries after finer regrinding were to more than 90 % caused by improved liberation with the remainder contributed by surface polishing effects. The practical implications of this work are that i) the comparison of particle grades with product grades allows to estimate the effect of regrinding on co-flotation/entrainment, ii) surface liberation models should be used for evaluating recoverabilities by flotation and iii) regrind circuits may be set up to ensure that all particles go through the mill or that only the coarse fraction is reground depending on the surface scrubbing found to be required.

Jan 1, 1993

By I. Filzwieser, M. B. Hanel, A. Filzwieser

The paper describes the current density increase within the last 150 years. From the beginning in 1885 at 30 A/m² up to the highest used current densities nowadays at 420 A/m² towards future pathways were even 1000 A/m² can be achievable. A short tour through history will highlight the milestones of the process of electrolytic refining of copper. Besides the improvement of the existing technology, the biggest changes leading to higher possible current densities are linked to the introduction of the ISA stainless steel plates and the introduction of the parallel flow principle. Furthermore, the parameters influencing the limitations regarding current density and therefore the practical used current density as well as the influence from the chemical composition of the electrolyte is discussed. Finally, the possibility of further increasing the current densities by enhancing the relative movement between electrolyte and electrode will give an outlook about the future of the copper electrolysis process. INTRODUCTION The current density is the most important characteristic to describe the productivity of a copper refining electrolysis besides the characteristic number for the electrical efficiency. Over the last 150 years, current density has risen from a few amperes per square meter to over 400 A/m² without any significant change in the principle of electrolytic refining. This increase in current density is documented exemplary by the electrolysis of Montanwerke Brixlegg in Austria (Brixlegg, 1963, 2013). The very beginning of the technology of electrolytic refining of copper was first patented in England by James Elkington in 1865 and the first electrolytic copper refinery was built in Newark, New Jersey, in 1883 (Armstrong, 1999). The secondary smelter Montanwerke Brixlegg, Austria, has been operating an electrolysis plant since 1884. In 1988, the third "Mount Isa" electrolysis plant worldwide and the first in Europe was put into operation in Brixlegg. Since 2010, the so-called high-current electrolysis (parallel flow METTOP-BRX Technology) with a current density of approx. 400 A/m² has been operated in half of the electrolysis process.

Jan 1, 2019

CAT offers three different methods to accomplish crowd & retract on an electric rope shovel Rack and pinion Rope crowd HydraCrowd The presentation will compare the three systems and introduce the benefits of the Hydracrowd

May 1, 2013

By John O. Marsden

Technology development and innovation has played a crucial role in the copper industry throughout history. The effective development and implementation of new technologies allows mankind to produce copper at progressively lower cost of production at a given feed grade and mineral type. This progress serves to counteract cost escalation over time and, depending on the magnitude of the cost benefit, allows ore cut off grades to be reduced thereby improving the availability, accessibility and utilization of mineral resources. The development of step change technologies that can offer >$0.15/lb total cost benefits provides a significant opportunity for producers to achieve competitive advantage, but it has been argued that rapid dissemination of technology makes such competitive advantage unsustainable over time. This paper presents the results of a recent study that evaluates a number of historical and emerging step change technology case studies in the copper industry and quantifies the associated cost benefits for users, the impact on the production cost curve, and the duration of such cost benefits for various categories of implementers: first mover, fast follower, conservative followers and laggards. The results provide a compelling case for major, mid-tier and emerging copper producers to invest in technology development initiatives if they wish to achieve and sustain competitive advantage over the long term. INTRODUCTION AND BACKGROUND A key issue for mining companies is how much time, effort and cost to spend on research and technology development (R&TD). The economic drivers for technology development and implementation are poorly understood in our industry and the business case is clouded by some notable and well-publicized failures (McNulty, 1998). Mining companies are in business to deliver financial returns to investors. This means delivering short term results on a quarter-by-quarter reporting basis as well as sustaining and growing the company to retain and reward a sustainable longer term investor base. The cyclical nature of the commodity metal markets makes it challenging to maintain investment in research and step change technology development: Mining companies must manage through the highs and the lows of price cycles, typically ranging from 5-15 years in length. The discounted cash flow approach to investment evaluation results in weak financial justification for R&TD expenditures. A clear and compelling rationale to support longer term investment in research and step change technology implementation is required.

Jan 1, 2019

By Gerardo Fuentes

Arsenic extraction from Chilean copper concentrates up to nearly 99% was achieved, using hydrothermal reactions. Arsenic appears in nature in more than 200 mineral species, being arsenopyrite (FeAsS), enargite (Cu3AsS4), and tennantite (Cu12As4S13) the most common species. In addition, arsenic is present in a large amount of copper concentrates, produced in northern Chile. Medical statistics show that in northern Chile, the amount of cancer to the lung, skin and bladder are the highest in the country. The latter situation, demonstrates the importance of studying metallurgical processes that do not generate atmospheric pollution. The hydrometallurgical processes such as hydrothermal treatment in autoclave reactors, do not produce gaseous emissions. On the other hand, the arsenic remains in solution from where it can be transformed in scorodite by widely known methods. Previous works about hydrothermal treatment of enargite have shown the feasibility of transforming the enargite of the copper concentrates into chalcocite or mineral species of the chalcocite family such as djurleite, digenite and for this reason enrich the concentrate in copper and pass the arsenic to solution. For this research, two Chilean copper concentrates were used, concentrate 1 with 5.5% arsenic and concentrate 3 with 1.8% arsenic. These concentrates were subjected to a complete chemical and mineralogical characterization. Later these concentrates were carry out to batch tests of hydrothermal treatment. Also, these concentrates were subjected to grinding to have different particle sizes. For the hydrothermal tests, a liter capacity Autoclave Engineer reactor was used. Characteristic of this reactor was the maximum temperature 350°C, 5000 PSI pressure, and 900 rpm agitation speed. Kinetic tests were carried out with the two concentrates maintaining the same solid: liquid relationship, the same agitation velocity and the variables studied were treatment temperature, time of reaction, concentration of copper in the solution and grain size of the concentrates. The conclusions of the study indicated arsenic extraction of the order of 93.98% from the concentrate 1 and arsenic extraction of the order of 98.74% from concentrate 3. After the hydrothermal treatment, the solids and solutions were characterized chemically, by electron microscopy and X ray diffraction. Also the solids were characterized by grainsize through a particle size analyzer (MICROTRAC). Results of batch treatment shows that arsenic can be release almost completely from real copper concentrates using this hydrothermal process and the next stage will be a scale up process in order obtain results for pilot plant design. INTRODUCTION Arsenic is an impurity that appears associated with copper minerals forming enargite, tennantite, tetrahedrite, and that due to the pyrometallurgical treatment either in conversion or roasting furnaces, it goes into the atmosphere together with the sulfur dioxide. A great quantity of literature can be found to eliminate arsenic or try to separate arsenic from copper. The methods used are mainly leaching processes with or without pressure (Padilla, Jerez & Ruiz, 2015) with different reagents like chloride media (Herreros, Fuentes, Quiroz & Viñals, 2003) or chloride media with sulphuric acid (Riveros & Dutrizac, 2008) or sodium hypochlorite (Mihajlovic, Strbac, Zivkovic, Kovacevic & Stehernik, 2007). It is known too that Chile is the first copper producer in the world and a great quantity of its minerals are in the north of the country, in Antofagasta.

Jan 1, 2019

By Damian Connelly

The option to leach iron from low grade copper concentrates could reduce transport costs and significantly improve the saleability of the concentrate. In addition, it reduces smelting costs and can remove undesirable impurities. The trend to produce cleaner and higher grade copper concentrates is very appealing to the smelters. A recent copper project came on line and there were three serious deficiencies which were not identified in the feasibility study. This came as a surprise and resulted in a number of projects to investigate ways of rectifying the problems in the shortest timeframe possible and using minimal new capital. The first serious issued not identified when commissioning was the lower than expected copper recovery, which was 70% compared to a predicted recovery of 80% to 87% in the feasibility study. This required investigating new flotation reagents and incorporating controlled potential sulphidisation. The second serious issue overlooked is the presence of significant amounts of talc minerals (insol) in the ore which are naturally floatable. This leads to lower concentrate grade and attempts to remove the talc resulted in lower copper recovery. Smelters have limits on the amount of talc in concentrate because it produces viscous slags and difficulties for the smelter. It also incurs higher transport costs. The third serious issue not identified in the feasibility study was the high arsenic reporting to the concentrate. Arsenic is a penalty element for smelters and at levels exceeding 0.3% the smelters may reject the concentrate. Arsenic is a problem environmentally for copper smelters and penalties apply when it is high. This paper describes the options for penalty element removal and suitability to incorporate into the modified flowsheet. It also highlights where the geometallurgy was not properly addressed and how these surprises could have been avoided. INTRODUCTION From 1970 to 1985, a copper company undertook metallurgical testwork on the Peruvian project copper ore. The ores were mined underground and treated over many years previously. Various other groups undertook studies and work until Aker Kvaerner undertook a feasibility study in 2006. Three ore composites were tested and grind-recovery relationships were developed. The feasibility study testwork identified that talc was a possible concern and will have an impact on copper concentrate grade. This was to be managed by blending. The current operating reality is that there is so much talc in the ore body it is not possible to blend it out. There was far more emphasis on molybdenum recovery. No mention was made of arsenic issues other than blending. There was a Concentrate Leach Study and a Molybdenum Hydrometallurgical Plant Study but these options did not proceed to a final flowsheet. A Scoping Study in 2006 looked at a Heap Leach project. The heap leaching gave very poor copper recovery on the sulphide ore. Heap Leaching was evaluated and tested for the high talc and high arsenic ore but recoveries were poor. The Aker Kvaerner feasibility study opted for a simple primary crush SAG/ball grind followed by flotation and sale of a concentrate. This is the current flowsheet utilised and the scale of the project is very large based on processing 117,200 tonnes of ore per day. A feasibility study does not guarantee success and the deviations from the feasibility study suggest there is a lot of technical work required to improve the current metallurgical performance.

Jan 1, 2019

By Xian Jian Guo, Lei Li, Hua Wang

The distribution and behavior of As, Pb and Zn elements in the copper smelting process were investigated using thermodynamics. The differences between thermodynamics evaluation and practical smelting processes were analyzed. The main factors affecting the distribution of the elements are oxygen enrichment in blowing, copper matte grade and smelting temperature. In general, the distribution ratio of As, Pb and Zn to off gas increases with the smelting temperature and decreases with oxygen enrichment in blowing. Meanwhile, their distributions in matte decreases and that in slag increases with the increase of copper matte grade. There is some gap in distributions between thermodynamics evaluation and practical smelting processes. INTRODUCTION The copper concentrates usually contain a number of minor elements, the control of which in copper smelting processes is often a key to the quality of the anode copper produced and may also have a bearing on the overall economics of the process (Yang et al., 2017). Knowledge of the thermodynamic properties of the minor elements in slag is very important in the control of the slagging reactions (Takeda Y, Ishiwata & Yazawa, 2007). In addition, the environmental contamination caused by the minor elements associated with copper-bearing ores, such as As, Pb and Zn, has become more and more important (Wang, 2004). Arsenic, lead and antimony, which are all carcinogenic metalloid elements, are usually contained in iron-rich wastes, and theirs emissions are considered to be one of the foremost environmental concerns (Wang, 2004). It is important to elucidate the elements distribution of them in the reducing-matte smelting process. The distributions of As, Pb and Zn elements in the copper smelting process are dependent on many factors, including the temperature, raw material composition, reduction atmosphere, concentration level, and slag chemistry etc. (Chen L Z, Xu X, 2016). Generally, these minor elements mainly distribute in phases of gas, copper matte and slag in the smelting process (Shu, Wang, & Qu, 2016). The arsenic exists mainly in the form of sulfo-arsenides in the copper concentrate, and it will decompose and be oxidized in the smelting process (Chen & Lu, 2016). Part of the products, including AsS, AsO, As2 and As2O3, evaporates into the gaseous state, and some other part enters into slag phase in the form of As2O3 and As2O5 (Wang, Guo, & Tian, 2017). Meanwhile, the As2O3 in the slag phase can also be reduced to metallic As and combine with Cu, S, Fe forming Cu3As2, As2S3 and Fe3As2, and then enter into copper matte. During the copper smelting process, about 50% of zinc enters into slag phase in the form of ZnO and 45% exists in the copper matte in the form of ZnS. Little volatizes into the gas phase. Most lead exists in forms of PbS and PbO in the copper concentrate, and it is mainly distributed in copper matte in the smelting process (Zheng & Lin, 2015).

Jan 1, 2019