Search Documents

By R. G. Rosehart, S. Y. Lee

"The current investigation concerns the removal of arsenic from waste waters using ion-exchange resin and activated carbon as sorption media. Use of certain weak and strong base anion exchange resins permits the removal of arsenic. Arsenic may be loaded on the weak base resin in the pH range of 2 to 3 and on the strong base resin above pH 5. The elution of arsenic is successfully achieved using 0.5 M NaCl or a mixture of NaCl and NaOH. The activated carbon investigated was less effective on loading arsenic, but the arsenic loaded was easily eluted by simple pH adjustments."

Jan 1, 1972

By A. Haque

"This paper describes an improved formulation of an analytical shear strength model developed by Haque & Kodikara (2012) by incorporating the failure of regular concrete/rock joints subjected to CNS condition. Sokolovskii’s analytical solutions developed for failure stress of slopes have been found to be effective in this regard. The analytical models have been validated for predicting the shear behaviour of concrete/rock joints subjected to various CNS loading conditions. The model has been found to accurately predict the dilation, normal stress and shear stress behaviour for a regular triangular saw-tooth joint up to the peak shear stress. Moreover, the peak shear stresses of concrete-rock joints with asperity angles ranging from 5 to 27.5o compared reasonably well with the available laboratory test results.INTRODUCTIONA new shear strength model for elastic regular triangular concrete/rock joints loaded under Constant Normal Stiffness (CNS) boundary condition has been developed by Haque & Kodikara (2012). The salient feature of this model is its capability of accurately estimating the normal and shear stresses of joints with shear displacements under CNS condition by incorporating the elastic deformation of asperities. However, the shear strength model of Haque & Kodikara (2012) for the elastic asperities cannot be directly employed to predict the peak shear stress of a joint experiencing plasticity under applied loads. Therefore, the model inevitability requires articulation of an appropriate shear failure criterion simulating the boundary conditions of the loaded asperity to predict the peak shear stress and corresponding normal stress and dilation behaviour of concrete/rock joints. Sokolovskii (1960) developed a set of analytical solutions for failure stress of slopes comprising c-??soils, which can be exploited effectively to simulate the failure condition as encountered for loaded regular triangular concrete/rock joints (Seidel & Haberfield, 2002)."

Jan 1, 2015

By John S. Stevenson

Zeballos mining camp is on the west coast of Vancouver island; 195 nautical miles northwest from Victoria.; The spectacularly rich gold-bearing veins that made Zeballos an important; gold camp were found early in 1934. Small pockets of very coarse; gold had been found earlier under large boulders at the mouth of Spud; creek; and in the autumn of 1933 rich gold-quartz float was found near the; mouth of the creek. The rocky beds of the steep creeks entering Spud creek; were searched for its source and as a result the veins on the White Star property; were found. The Goldfield vein on the Spud Valley property was discovered; in 1935; and the No. 1 vein on the Privateer in 1936. In the general; prospecting activity that quickly followed; other veins were found; not; only in Spud creek but in other creeks draining into Zeballos river.

Jan 1, 1954

By P. Blonde

Recent analysis has suggested that a balanced recovery profile can improve flotation bank performance. Test work was conducted to test the balanced profile concept at the Penhorwood talc mine near Timmins, Ontario, Canada. Plant trials were devised to determine how to control the recovery profile and the resultant impact on grade and recovery in a rougher bank of four cells. Accompanying gas dispersion measurements revealed a maintenance issue with one cell that was corrected. By manipulating air and frother addition it was possible to bring the bank closer to a balanced recovery profile and the down-the-bank grade/recovery improved. Plant production showed an increased talc grade at similar yield with the balanced profile. The results provide justification for a long term plant trial.

Aug 1, 2013

By SeyedBijan Mahbaz

Development of Geomechanical Earth Models (GEM) is a prerequisite to reservoir management, involving issues such as stress path analysis, prediction of induced seismicity and sanding initiation, and coupled flow-stress modeling that leads to more realistic predictions of oil rates and rock response. Part of GEM development is the stipulation of the 3-D lithostratigraphic disposition (geometry) which is used to choose the geomechanical units. The digital geological model is then populated with quantitative and semi-quantitative data on rock properties, fluid properties, saturations, initial conditions (p, T, [_]) and other information. Both fluid and solid properties are needed this requires integration of geomechanics skills with geophysical and rock physics skills, and this article deals with a subset of this integration process, with an example from two wells in southwest Iran.Rock physics approaches are used to predict reservoir rock and fluid properties with wellbore and 3-D seismic data, which are also used to interpolate rock mechanics properties to the inter-well regions. The first step in a generic rock physics approach is diagnostic and involves the introduction of a suitable Rock Physics model.Acoustic impedance (AI), shear impedance (SI), and density (_) are the fundamental rock properties usually derived using AVO equations, and these parameters, along with attenuation coefficients, can then be correlated to static rock mechanics properties that define deformability and perhaps even strength. In this study, Poisson Impedance is introduced as a new seismic attribute used for lithology and fluid differentiation in the FahliyanFormation (reservoir rock) in two oil wells in the southwest of Iran. To do this, a novel rock physics model was developed for this naturally fractured carbonate reservoir.Currently, these data are also being used to correlate to a limited rock mechanics data base to develop a more extensive GEM to serve as input to more general geomechanical and reservoir modeling tasks.

Jun 1, 2012

By W. J. Jenner

"Introduction The Saskatchewan Power Corporation is a provincial crown corporation which operates under a mandate to supply all customers within Saskatchewan with electricity and natural gas. The Saskatchewan Power Corporation operates two coal mines within the province of Saskatchewan. The Souris Valley Mine is located a few miles south of the city of Estevan and produces approximately 300 000 Mg of lignite per year. The lignite is shipped about four kilometres by truck and burned at the 882 MW Boundary Dam Power Station, also owned by the Saskatchewan Power Corporation. The Poplar River Mine is located just south-west of the town of Coronach, Saskatchewan which is some 190 kilo metres west of Estevan. This mine produces approximately 1 675 000 Mg of lignite per year. The lignite is shipped seven miles by rail to the Saskatchewan Power Corporation's Poplar River Power Station. The Poplar River Mine is the sole sup plier of fuel to the Poplar River Power Station, which generates some 300 MW of electrical power. A second 300 MW unit is due to be commissioned at the Poplar River Power Station in mid-1983 and the Poplar River Mine will have doubled its capacity to approximately 3 350 000 Mg per year by that time: Souris Valley Mine Geology The Souris Valley Mine extracts lignite from the Estevan seam of the Ravenscrag Formation. This formation is of Tertiary age and was deposited during the Paleocene Epoch. The Ravenscrag Formation outcrops throughout southern Saskatachewan and all coal mined in the province occurs in this formation. Ravenscrag sediments are deltaic in origin and are composed of a series of fine sands, silts, clay and lignite deposits."

Jan 1, 1985

By L. R. Bottomer, G. M. Leary

"The Copper Canyon property is located in the Galore Creek area of northwestern British Columbia. Porphyry copper-gold mineralization on the property is notable for its high gold content and close spatial relationship with a distinctive suite of high level syenitic and monzonitic intrusions, and pseudoleucite-bearing volcanic country rocks. The style of alteration and mineralization is similar in many respects to the nearby Galore Creek deposits.The current geological resource of 32.4 million tonnes grading 0.75% Cu, 1.17 g/ t Au and 17.1 g/t Ag is insufficient to support a mining operation, but definition of additional reserves combined with improved transportation infrastructure in the region may change this in the future. The climate, topography and proximity to an active glacier indicate that the most likely production scenario is an underground bulk mining operation, with the ore being milled offsite.IntroductionThe property is located at 57°07' North latitude, 131 °21' West longitude, on NTS sheet 104G/ 3W, approximately 160 km northwest of Stewart and 90 km south of Telegraph Creek (Fig. 1). The Galore Creek camp and airstrip are located 6 km to the west. Current access to the property is via helicopter either from Galore Creek, or from the Bronson Creek airstrip 32 km to the south-southeast.The deposit occurs within the Boundary Ranges of the Coast Mountains, on the north side of the east fork of Galore Creek, which flows northerly into the Scud River and thence westerly to the Stikine River.Topography is rugged. In the deposit area, elevations range from 1130 m to 1750 m. Valley glaciers and permanent snow and ice fields are characteristic of the region at these elevations, and at its southern limit, mineralization is truncated by the East Fork Glacier.The property is entirely above the treeline, and except for areas of moraine cover and talus slopes, outcrop is abundant."

Jan 1, 1995

By Neda Zangeneh

Production efficiency from low permeability gas shales require techniques to optimize hydraulic fracture completions. One completion strategy involves the simultaneous or near simultaneous hydraulic fracturing of multiple horizontal wells to maximize the fracture network area and stimulated reservoir volume. However, changes to the in-situ stress field caused by an earlier hydrofrac on subsequent hydraulic fractures are not accounted for in traditional hydrofrac design calculations. Presented here are the results from a set of transient, coupled hydro-mechanical simulations of a rock mass containing two wellbores using the discontinuum-based distinct-element method. The results demonstrate the influence of stress-shadows generated by a hydraulic fracture on the development of subsequent hydrofracs from an adjacent well. It is shown here that these interactions have the potential to change the size and effectiveness of the hydraulic fracture stimulation by changing the extent of the hydraulic fracture around the secondary well.

Jun 1, 2012

By B. R. Rakishev

Balanced development of mining works at all the benches of a working zone by use of the excavator-automobile complex is achieved by transition to the technology of the bench excavating with cross panels by the two-sub-bench scheme with the changing levels of the working platforms (is patented in Kazakhstan). In deep quarries realization of this technology will allow to reduce the current volumes of the stripping ore excavation by 10?15 % and more, to increase the opened reserves of minerals by 20?50 % to decrease volume of mining-capital works for construction of stripping excavations by 2?4 times and to provide efficient use of powerful excavator-automobile complexes.

Aug 1, 2013

By Xu Wang, Yizhe Zhang, Yangge Zhu, Xiao’ou Xia, Fangming Liu

"The progress of lean magnetite preconcentration in China was introduced in this paper, such as using coarse crushing to reject tailings, and multistage grinding, multistage magnetic separation. The applications of “more crushing and less grinding” process and equipment in lean magnetite preconcentration could reduce production costs effectively. The related analysis and study on concrete cases were carried out in this paper.INTRODUCTIONIn the case of the slowdown and weak recovery in the global economy, bulk commodity prices fell sharply in 2015. Take iron ore's prices for example, about 60% grade iron ore's import prices in China from about $65 per ton at the beginning of 2015 fell to about $42 per ton in the end of the year, down by about 35%. But iron ore resources are non-renewable resources, with the continuous development and utilization of mineral resources, high grade iron ore resources will be exhausted gradually. Accompanying with the economic recovery iron ore prices after this fall is bound to return to its value to maintain a high level.The development and utilization of resources is gradually turning to the low grade iron ore. Restricted by technical development level and disadvantages of lean iron ore resources, the cost of utilization lean iron ore resources is relatively high. Making full use of their rich lean ore resources has become many countries' important strategy to get rid of dependence on foreign countries' ore. Over the years with the development and progress of lean magnetite mineral processing technology in China, the production number of concentrator has been greatly improved.As the world's largest steel producer and consumer countries, ensuring a stable and continuous supply of iron ore is particularly important for the healthy development of China's iron and steel industry. Chinese iron ore production and import data in recent years are showed in Table 1.With the expansion of iron and steel production, iron ore demand has also been a phenomenal growth. Taking 2013 for example, China's crude steel production is about 780 million tons in 2013, accounting for about half of the world's total output of crude steel. At the same time, China is also the first major iron ore import countries whose iron ore imports in 2013 was about 820 million tons, an increase of about 10%. The degree of external dependence is very high. In some years, the cost of China's iron ore imports was even more than $100 billion, and second only to oil’s import cost in all bulk commodities."

Jan 1, 2016

By Kevin C. Milne

"The solution of problems associated with development of a sour gas reserve will be of increasing importance in tl1e next few years if gas export is approved •by the National Energy Board. The purpose of this paper is to review briefly the history of the Carstairs gas field, and tCI describe in a general manner the reservoir, and the producing and processing facilities.HISTORYThe Carstairs gas field was discovered in April 1958 when the discovery well, Home Carstairs 10-17, was successfully completed as a gas well in the Elkton member of the Turner Valley formation. Geo-graphic location of the field is shown in Figure No. 1. Note that the field is about five miles west of the town of Carstairs, Alberta, which in turn is about 40 miles north of Calgary. Drilling subsequent to the discovery well resulted in three addition-al producing wells and one dry hole during I.958; two producing wells during 1959; and one producing well and one dry hole during 1960. Thus, seven producing wells and two dry holes have been drilled in the Carstairs field to date.In November 1959 a 12-section block in the Carstairs field was unitized on a surface acre basis. Mean-while, in June 1959, operators in the field executed an ""Interim Plant Agreement"" that provided the money needed to start construction of a joint venture processing plant and gathering system. Construction of the plant and gathering system was completed in February 1960."

Jan 1, 1960

By H. J. B. Couto, J. G. S. Puelles, M. L. Torem, R. H. Rojas, A. G. Merma

Understanding the limits of fine particle flotation is fundamental to achieving a significant and selective separation. Conventional flotation processes are not suitable to treat these particles because of their low collision efficiency. This problem can be overcome by decreasing the bubble size or by increasing the apparent particle size. However it is worth noting that the use of small bubbles or micro bubbles also involves some disadvantages such as their low momentum resulting in a slower process comparing with conventional flotation. Electroflotation is an attractive alternative for treating fine particles with small bubbles less than 100 µm, generated by the electrolysis of water. In this sense, this study assesses the effect of current density and pH on bubble size in a binary electroflotation cell. An increase in the bubble generation rate was reported with an increase in current density. In addition, at acid pH values, the size of oxygen bubbles increased and conversely decreased at basic pH values; this may be due to the electrostatic attraction between the oxygen bubbles and the anode resulting in a greater nucleation time. An opposite trend was observed with the hydrogen bubbles. These results are in agreement with their electrokinetic studies, which reported that at acid conditions the bubble surface may be positively charged for both the hydrogen and the oxygen bubbles. Finally the bubble size was slightly affected by the electrolyte concentration, resulting in smaller diameter bubbles at higher concentrations.

Jan 1, 2016

By S. Kashani-Nejad

The formation of oxides during the dehydration of MgC12,6H20, Bischofite, was studied by heating the bischofite over a range of time and temperatures in ambient atmosphere. Using a methanol-leaching technique developed by authors, the oxides that formed were isolated, identified and assayed. Three distinct regions of oxide stability were identified. The oxide produced at dehydration temperatures less than 300 °C was Mg2(OH)3C1,2H2O; at 300 °C, mixtures of MgOHC1 and Mg2(OH)3C1.2H2O were formed and at 400 °C, MgOHC1 was the only oxide produced. The presence of MgO observed in the products of the dehydration of bischofite at temperatures above 400 °C was due to the thermal decomposition of the MgOHC1 that was formed while the sample was heating to over 400 °C.

Jan 1, 2006

By L. Cheng, Y. W. Pan, Y. R. Liu

"Impounding deformation of slope and foundation is significant during and post dam construction. Reservoir impoundment is accompanied with various phenomena, including material degradation, effective stress decreasing and buoyancy in rock masses. These phenomena are related with some engineering concerns like reservoir-induced earthquake, landslide and dam stability. The Malpasset dam and Vajont dam are typical hydraulic projects suffering from seepage in dam foundation and slope, which finally led to failure and landslide. Pore pressure in jointed rock masses is considered in constitutive relation. The expression of effective stress for porous rock with fluids is incorporated into the Drucker-Prager criterion. Based on monitoring data of valley width and dam deformation, the effective stress law is applied to analyse the impounding influence of slope and foundation to Jinping-I high arch dam. The dam is accompanied with complicated topographical and geological conditions. The results show that calculated and monitored values agree well, and the application of effective stress law provides an approach to evaluate dam deformation, stress and stability with impounding effect considered.INTRODUCTIONImpounding deformation of slope and foundation is a common and significant problem during dam construction and operation. This phenomenon exists in a lot of reservoirs in China, like Laxiwa, Ertan, Xiluodu and Jinping-I arch dams, and some dams in Europe. It is related with some engineering concerns like reservoir-induced earthquake, landslide and dam stability. The Malpasset dam and Vajont dam are typical hydraulic projects suffering from seepage in dam foundation and slope. Monitored data indicates that the valley width tends to shrink in hydraulic engineering during the impounding process, which will change the stress and deformation of dam and abutment. Therefore, global stability of dam and foundation should be evaluated with impounding process taken into consideration."

Jan 1, 2015

By G. A. Vissac

In this paper we intend to deal particularly with the economic side of coal washing as it applies to our mines. We will then discuss why the dry-cleaning process has been selected, and give a brief description of our plant, dwelling only on its specific features and referring the reader to the numerous papers published on the subject for any details on the principles and machinery used in dry cleaning. ECONOMIC DISCUSSION The washery introduces an extra cost for depreciation, operation, and loss in treatment. A certain proportion of the coal, now being sold, and which the miners have been paid for. will have to be wasted. As a whole, the total increase in cost would be approximately 60 cents per ton. On the possibility of recovering this amount depends the success of the washery. There are two advantages to be expected from the washery, the first, which occurs at the mine and which will be certain; the second, more difficult to estimate, because it depends upon convincing our customers that they should pay more for a better product.

Jan 1, 1924

By G. R. Guillet

Salt is restricted to five major beds in south western Ontario, totalling as much as 200 m in thickness. These beds are located at depths ranging from 270 m to 750 m below the surface, fringing Lake Huron and the Detroit River from Windsor to Kincardine, and extending inland as far as London. Manitoulin Island, the Bruce Peninsula and the north part of the Niagara Escarpment form the northeastern rim of the Michigan Basin, a major structural depression in which the salt was deposited 400 million years ago when much of North America was covered by the Silurian sea. Salt is mined underground at Windsor and Goderich; it is also brought to surface as brine through deep wells at Windsor, Samia and Goderich. Artificially- created caverns in salt beds are extensively used for storage of liquid hydrocarbons at Windsor and Samia.

Jan 1, 1984

By C. DeLong

"The Mt. Milligan porphyry copper-gold deposits are in central British Columbia, 155 km northwest of Prince George. Mineralized outcrops and float were discovered in the Mount Milligan area by prospecting. The most recent discoveries, which utilized lithogeochemistry, were in 1983. Areas containing the outcrops and float then were investigated by geological mapping, soil and lithogeochemical sampling, ground and airborne geophysical surveys, trenching and diamond drilling. This work led to the discovery of the Mt. Milligan Main deposit in 1987 and the Southern Star deposit in 1989. Extensive diamond drilling continued until 1991 and delineated a measured and indicated resource of 299 million tonnes grading 0.45 g/t Au and 0.22 % Cu from the combined deposits.The Mt. Milligan deposits lie within the Early Mesozoic Quesnel Terrane and are hosted by porphyritic monzonite stocks and adjacent volcanic rocks of the Takla Group. The Mt. Milligan Main deposit is centred around the MBX stock and Rainbow dike, and the Southern Star deposit around the Southern Star stock.Potassic alteration is extensive within the stocks and in volcanic rocks adjacent to the MBX stock and Rainbow dike. Propylitic alteration surrounds the potassic alteration and decreases in intensuy away from the stocks. Mineralization consists mostly of pyrite, chalcopyrite, lesser magnetite, and minor bornite, molybdenite and gold.Mineralogical zoning is well-developed within the deposits. A biotite-rich subzone forms the core of the potassic alteration zone and hosts most of the copper and gold. Numerous polymetallic veins lie within the propylitic alteration zone just beyond the limit of porphyry-style copper-gold mineralization."

Jan 1, 1995

By L. Rao, P. Carabin

"Advances in thermal plasma torches have resulted in this technology becoming a commercially viable solution for chemical and metallurgical processes. The main advantages of plasma are its ability to control process chemistry and to build small footprint reactors due to its high energy density and reactivity of the free radicals that are produced. This paper focuses on thermal plasmas produced by DC torches and their applications for waste treatment, production of high purity metals, and nanomaterials. Both transferred and non-transferred torches have been used as either a source of heat or as a reagent in various industrial processes. INTRODUCTIONPlasma technology has become an ideal solution for many industrial chemical, metallurgical and mechanical processes (Venkataramani, 2002). Thermal plasma powered systems are typical used for their unique characteristics such as high energy densities, high temperatures, small installation sizes, rapid startup and shutdown features, controlled process chemistry and use of electrical energy as a heating source resulting in decoupling the heat source from the oxygen flow rate (Heberlein et al., 2007). Depending on the nature of the main plasma forming gas used, thermal plasma systems offer a high temperature heating source coupled with a highly reactive plasma plume rich in free radicals and ions which promote otherwise hard to drive chemical reactions, as well as high heat transfer rates.Industrial plasmas can be broadly classified as thermal plasmas and non thermal plasmas. Thermal plasmas are atmospheric pressure plasmas characterized by local thermodynamic equilibrium (Boulos et al., 1994). Thermal plasmas are typically established between any two current conducting electrodes separated by an insulator. A plasma forming gas is blown between the two conducting electrodes resulting in a high temperature plasma plume. A plasma torch generates and maintains an electrically conducting gas column between the two electrodes; a cathode (negative electrode) and an anode (positive electrode) (Camacho, 1988). If both electrodes are housed in a single housing, resulting in an arc enclosed inside the plasma torch, then such plasma generating torches are termed as non-transferred (NT) plasma torches, whereas, if the second electrode is external to the torch, creating an arc transferred between the cathode and the working piece, then such plasma torches are termed as transferred (T) plasma torches. Depending on the source of the electricity which can be either direct current (DC), alternating current (AC) at main network frequency or at radio frequency (RF), the plasma torches are classified as DC, AC or RF plasma torches (Venkataramani, 2002)."

Jan 1, 2012

By S. N. Yu

Tele-operation manipulators applied in this paper are systems for the remote handling and management of pyroprocessing related facilities in an Argon cell of the KAERI (Korea Atomic Energy Research Institute). Generally, these kinds of systems are composed of a master-slave system and its peripherals installed along the wall of the cell, with the master transmitting the user?s own motion to the gripper directly. This study introduced various considerations and modifications to improve the remote handling performance. The analysis of an operator's ability using his/her own upper arm motion range while manipulating the MSM, and considerations of its manipulation margin and the related tool modifications are also included. Finally, the test results of several remote handling tasks are presented, and an adequate operation strategy for the tele-operation system of hot-cell type facilities is proposed.

Aug 1, 2013

By Man-Chao He

One of the critical problems involved in deep coalmines is unusual gas emissions. Many researchers agree that there is a relationship between coal gas emissions and geological features such as tectonics or geological disturbances, gas content, properties of the coal and rock and the mininginduced stress state in the coal seam and rock. Thus, the present paper intends to investigate complex mechanical phenomena during the process of gas emission in underground coal-mines. A program of laboratory testing was undertaken to study the effects of temperature and pressure on mechanisms of gas emission. It must be noted that this paper describes new techniques developed to simultaneously measure deformation and gas pressure, as well as flux during the test, taking the characteristics of gas transport into consideration under certain temperature and pressure conditions. The results indicate that under certain temperature and pressure conditions, gases adsorbed to coal start to desorb, and increase the pore pressure. High pressure gases entering coal fractures can generate high tensile stresses near the crack tips, leading to crack propagation and coalescence, which in turn can cause the specimen to dilate. From the experimental viewpoint, these test results may help us discern why mining seismic events can trigger gas emissions.

Aug 1, 2013