Search Documents

By G Anders

The mucking out of sub-level headings by slusher and by Autoloader is described, and the performance and costs of both methods are compared. The introduction of the Autoloader is taken as an example to illustrate the meth-od used at the mine for evaluating the suitability of new equipment. The consecutive steps in the process are covered in detail -from the preliminary cost analysis and the preliminary estimate of savings and advantages, and the review of these data after a field investigation, through the elimination of dubious factors, and detailed time and performance studies at the property, to the final assessment of the new equipment and an evaluation of the initial forecast. The Autoloader in Operation. 1198 Introduction AT Mattagami Lake Mines Ltd., the mine workings are laid out basically on a pattern of 60-ft.-wide stapes alternating with 60-ft.-wide pillars, with stope lengths varying from 80 to 200 ft. and stope tonnages generally between 80,000 and 200,000 tons. Stapes are drilled off from sub-levels at 60-ft. intervals, with the

Jan 1, 1965

By R. U. Seneviratne, B. K. Ahlgren

In this paper we follow various technological discoveries and developments in the purification of minerals and metals in the mining industry by ion exchange. For approximately 100 years, ion exchange has been a known and variously applied purification and separation technology used by scientists and producers. It would seem obvious that the producer’s objectives have always been to achieve the highest quality products and the lowest operation costs, but also with the least amount of technological complexity. As a strategy to reach these goals, much effort has been expended in the quest to improve continuous ion exchange (CIX) systems by reducing utility needs and resin degradation or loss while at the same time improving productivity and reliability. Recent developments from a number of companies have pushed equipment boundaries, resulting in a variety of unique commercial equipment designs each with a varying degree of success. The challenge set forth for all new designs has been a truly continuous process with no sacrifice in the afore mentioned benefits. One very recent equipment design based on system symmetry appears to meet many of these objectives with greater flexibility and less complexity resulting in better economics for the producer.

Jan 1, 2014

By Jan Drzymala, Przemyslaw B. Kowalczuk

"Flotation is possible when the forces operating between a bubble and the attached particle are properly balanced. There are many forces operating in the bubble-particle aggregate. The magnitude, location and direction of the forces depend on the type of process. The simplest arrangement in flotation is when a spherical bubble is attached to a spherical particle and both are immersed in water. In such a system there are four essential forces which shape the stability of the bubble-particle aggregate. They are excess pressure and interfacial solid/liquid, solid/gas and liquid/gas forces. A proper analysis and balance of the size, location and direction of these four principal forces lead to a general equation delineating the stability of the spherical particle–attached bubble system. Specific cross sections of the system and solution of the general equation lead to different relationships including the Young formula as well as the well-known geometrical relation between contact angle, particle and bubble radiuses. The arrangement of forces in the proposed graphical representation of the Young law is different from that presently used in literature for a bubble attached to an unmovable solid particle. Many real solid/liquid/gas systems are more complex due to the presence of additional forces which change the regular curvature of the liquid/gas interface leading to advancing and receding contact angles.INTRODUCTIONThere are numerous papers (Athukorallage, Aulisa, Iyer & Zhang, 2015; Chau, Bruckard, Koh & Nguyen, 2009; Drzymala, 1994; Lubarda, 2012; Pellicer, Manzanares & Mafe, 1995; Wang, Cui, Zhou, Xu, Sun, & Zhu, 2014; Young, 1804) and books (Davies & Rideal, 1963; Defay & Prigogine, 1966; Lee, 2013; Lyklema, 2000) dealing with the solid/liquid/gas system. Many of them concern the three involved phases having the shape of a sphere or spherical cap and the formed contact angle. The contact angle is usually measured through the liquid phase and can be either smaller or greater than 90o. The essential part of these publications is a graphical representation of the system with the Young equation shown as a result of balance of only three forces that is the excess Gibbs (or Helmholz) free energy per unit area of the three involved interfaces (Davies & Rideal, 1963; Defay & Prigogine, 1966; Israelachvili, 1985) (Figs. 1a-c). The Young equation, when the gravity force/buoyancy is neglected, is:"

Jan 1, 2016

By D. J. Xue

Four kinds of coal-rock combination were subjected to three kinds of stress waves in the SHPB numerical simulation. The wave propagation and the changes of the strain energy in the coal-rock combination during the dynamic impact process were recorded as well as the contact force. The dynamic response law of coal-rock combination was obtained. It was found that the coal had better reflectivity than the rock because of coal with larger impedance. In contrast the rock had better transmissivity. As the crest value of the incident wave increased, the increment in the crest value of the transmitted wave weakened in the coal-coal group, coal-rock group and rock-coal group, in contrast, the increment in the rock-rock group increased.

Aug 1, 2013

By Z. Zhang, D. Bouchard, H. Blanchette, A. Lemieux

This paper describes quality control methodologies for the production of semisolid A356 aluminum slugs with the SEED process. A methodology based on destructive tests carried out with an apparatus measuring the force to slice the slugs is presented. The force measurements were correlated with the solid phase morphologies of the slugs and were validated against a non destructive methodology that consisted in monitoring the temperature evolution of crucibles to produce the slugs and the drained metal. Results from the destructive and non destructive methodologies are compared and discussed.

Jan 1, 2006

By Yutaro Fukase

Various types of service robots have recently been developed for guarding facilities, caring for the elderly, carrying objects, and cleaning buildings. As barrier-free facilities improve and their use expands, these robots have more space within which to move inside buildings. Yet robots that move autonomously rely on position-detection systems. Though improving rapidly, these systems are far from perfect in determining positions in certain situations, especially when robots navigate large areas or cross various locations. Our group is working to solve this problem by developing a position-detection system using random-dot patterns on a floor. First, we construct a floor with a random-dot pattern and register the positions of all of the dots into a database. As the robot moves across the floor, a camera on the robot captures an image of the floor beneath it and crops the dot pattern in the image. The cropped dot pattern is matched to the dot patterns in the database to determine the position of the robot and the direction in which the robot is facing or moving. In this paper we propose a self-localization system and matching algorithms derived from a space technology and present the results of several experiments.

Aug 1, 2013

By K. Sun, S. A. Argyropoulos

The assimilation and the exothermic behavior of Zn-Zr metallic powder compacts into molten aluminum was studied by measuring simultaneously the temperatures inside at the centerline of the compact, at its surface, and inside the molten aluminum bath, as well as the net downward force acting on the compact. In addition, the exothermic behavior of these compacts was also investigated in an argon protected atmosphere. The temperature rise inside the compact increases significantly with the mass ratio of zirconium in the compact and to a lesser degree with the aluminum bath temperature. Experimental results on the recovery of these compacts in molten aluminum will also be presented.

Jan 1, 2008

By Z. Zhang, X. -G. Chen, F. Breton, A. Arici

"The microstructure of Al-10Si-0.3Mg-0.5Mn alloy with 0.27% Zr and 0.19% V addition was quantitatively analysed and compared to the base material. The addition of Zr and V in the AlSi10Mg alloy exhibit a beneficial effect on the Si modification, resulting in the reduction of the size of eutectic Si particles on both as-cast and T6 conditions. The quantitative image analysis results show that the Zr and V addition and T6 treatment can reduce the size of the intermetallic phases. In addition, the presence of Zr and V is favour to the partial dissolution of the intermetallic phases during the T6 treatment. Different heat treatment procedures were tested to optimize treatment parameters. The mechanical properties of the alloys were evaluated using hardness measurements and tensile tests. The results show that the addition of Zr and V can remarkably improve the mechanical properties on as-cast and T6-treated conditions. The correlation between the microstructure and mechanical properties of the alloys is discussed.INTRODUCTION Al-Si-Mg foundry alloys have been widely used in automotive and aerospace industries due to their high strength-to-weight ratio, heat-treatable capability and excellent castability. The alloying elements such as Cu, Mn, Fe are traditionally added into Al-Si-Mg alloys to improve their mechanical properties (Mohamed, Samuel, Samuel & Doty, 2009). In recent years, the attention has been paid to the effect of the transition elements such as Zr, V, Ti, etc, as minor alloying additives, on the properties of aluminum alloys (Elhadari, Patel, Chen, & Kasprzak, 2011; Kasprzak, Amirkhiz & Niewczas, 2014; Shaha, Czerwinski, Kasprzak, Friedman & Chen, 2015; Shaha, Czerwinski, Kasprzak & Chen, 2014; Mahmudi, Sepehrband, Ghasemi & 2006; Meng, Cui, Zhao & Zuo, 2013). Kasprzak et al., (2014) and Shaha et al., (2015) reported that additions of Zr, V, and Ti in Al-Si-Cu-Mg cast alloys can improve the alloy mechanical properties at high temperature by forming stable intermetallics and precipitates on as-cast and heat treatment conditions. On the other hand, the mechanical properties of near-eutectic and eutectic Al–Si cast alloys depend not only on the chemical composition but also, even more importantly, on microstructural features such as the morphology and size of eutectic silicon and intermetallic particles, which are present on both as-cast and heat treatment conditions (Mohamed et al., 2009). However, there is rather limited information on the effect of Zr and V on the microstructure features and mechanical properties of near-eutectic Al-Si-Mg cast alloys."

Jan 1, 2018

By A. W. Jolliffe

DESPITE the widespread occurrence of scheelite in Canada, domestic production of this strategic mineral is still quite insufficient to meet wartime needs. Two difficulties have invariably arisen in prospecting for or developing scheelite deposits: scheelite is a difficult mineral to identify, and secondly, its distribution is commonly so erratic that the value of a deposit cannot be determined without arduous and expensive methods of sampling and wet assay. Scheelite's property of fluorescing under certain ultra-violet lamps overcomes the first difficulty and is the basis for a quantitative method developed to overcome the second. It is found that, by use of an ultra-violet lamp, the value of many scheelite deposits may be accurately and speedily determined. The method requires neither elaborate apparatus nor exceptional skill on the part of the operator, and is most applicable to those deposits where the bulk of the scheelite occurs in fairly pure aggregates that are at least one-tenth of an inch across. It has been used in grading some two hundred scheelite-bearing veins in the Yellow-knife-Beaulieu region, Northwest Territories, and various occurrences in the Porcupine district, Ontario. The method requires the measurement of the total area of scheelite exposed in any reasonably large measured cross-section of a deposit. From the areal percent of scheelite so obtained, the tungstic oxide (WO,) content of that part of the deposit may be calculated by means of equations of simple derivation.

Jan 1, 1942

By Yujing Jiang, Xuezhen Wu, Bo Li, Tomomi Iura, Gang Wang

"Yielding bolt has been widely used for rock reinforcement in mining and civil engineering in high stress conditions. However, the interaction mechanism of yielding bolt and matrix mass is still not clear at present, and no analytical model is available to predict its reinforcement effect quantitatively. In this paper, the mainstream yielding rock bolts were reviewed firstly. After that, a coupling model is proposed to account for the interaction between yielding bolt and matrix mass. Based on the plane strain axial symmetry assumption and the incremental theory of plasticity, equilibrium equations and compatibility equations of matrix mass, and also the response of yielding rock bolt are deduced theoretically. The proposed method was programmed in Visual Basic development environment, and a semi-analytical solution for the coupling model is achieved. The reinforcement mechanism of yielding bolt in conventional tunnelling is clearly demonstrated through an illustrative case study. The reinforcement effect of yielding bolt is estimated quantitatively, and the distribution of axial force along the bolt is presented. In addition, the validity of proposed method is verified by numerical simulations. INTRODUCTIONHigh stress in surrounding rock mass can cause serious stability problems such as massive squeezing in soft rock and rock burst in hard rock. It is observed that many conventional rock bolts failed when experiencing large displacement, which implies that they are too stiff to sustain large deformation and dynamic conditions (Stillborg, 1994; Hoek et al., 1995). Yielding bolt, which can also be called energy-absorbing bolt, has been widely used for rock reinforcement in mining and civil engineering for these conditions (Neugebauer, E., 2008). This paper focuses on the static reinforcement effects of the yielding bolts with analytical method and numerical simulations."

Jan 1, 2015

By D. Tetsuka, H. Okamoto

The amount of impurities to be processed in a copper smelting process has increased for recent years because of an increase in the electronic scrap amount. It has been found that Sb and Ni effect on the operation of our copper electrorefining process. It is found that the current efficiency of the copper electrorefining tended to be decreased as the Ni concentration in the electrolyte increased. The passivation of the process seemed to be more related to SO4 concentration in the electrolyte rather than the Ni concentration in it. The current efficiency decreased when the Sb content in the anode was high. A high Sb content in the anode caused easy passivation by forming a gel-like film in the slime layer. We have developed a method to for see the anode passivation in a short time while generating a slime layer. We confirmed the tendency of passivation through the experiment of changing Pb content in anode. Passivation was easily occur with an increase in Pb content in the anode. The amount of slime increased as the Pb content in the anode increased. This suggests that passivation was facilitated because liquid diffusion near the anode was inhibited. INTRODUCTION The amount of impurities to be processed in copper smelting has been growing in recent years because the amount of electronic scrap has increased. Figure 1 shows that the contents of Sb and Ni in copper anodes have increased since 2007.High Sb and Ni contents in the copper anode decreased the current efficiency of the process and made the quality of copper cathode poor because of the anode passivation and the formation of floating slime in the electrolyte during electrorefining. If these influences of impurities are suppressed, it would be possible to make copper electro-refining current density higher and to process much amount of electronic scrap. We examined the components of our copper electro-refining process like anode composition, slime properties and electrolyte composition, and investigated the mechanism by which Sb and Ni affect passivation and current efficiency. When examining the influence of Ni, we noticed that the SO4 important. The effect of SO42 – was also discussed

Jan 1, 2019

By P. Condori

Palabora Mining Copper (PMC) has two autogenous mills that have been in operation since 1976. The mills were originally designed to treat 30 000 t/d of open cast copper ore in a closed circuit with cyclones. As the ore body went deeper the open cast method of mining was changed to block caving, a consequence of this was the dolerite content (hardest barren material) increased significantly, increasing the production rate of pebbles and thus reducing the milling capacity. In order to cope with the increased ore hardness and to increase mill capacity, a second ball milling stage and pebble crushing were incorporated to the circuit. The above actions created new challenges to the circuit operation and bottlenecks in different areas of the milling circuit. This paper reports the holistic work performed on the Palabora autogenous milling circuit including the implementation of a mill constraint control scheme, the implementation of a pebble removal system from the circuit and a new circuit configuration. The achieved plant stability and increment of ore throughput are also reported in this paper.

Jan 1, 2012

This paper comprises a description of on-stream analysis instrumentation, including sample handling, X-ray optics and data processing. It also includes a discussion of some typical applications of an on-stream analyzer as related to the mineral processing industry. Introduction T WO automatic X-ray spectrometers have been developed for the simultaneous analysis of as many as six elements in a given sample. These instruments, namely the On-Stream Analyzer and the new Vacuum Simultaneous Spectrometer, have been designed specifically for process control in industry where large numbers of static samples or a number of flowing sample streams must be analyzed continuously with both speed and accuracy. This paper is concerned particularly with the application of these instruments for the continuous analysis of dynamic samples. The Instruments The On-Stream Analyzer and the Vacuum Simultaneous Spectrometer are intended to serve industry by offering two basic approaches to the problem of continuous sampling of flowing sample streams. The On-stream Analyzer (Figure 1) is designed for the completely automatic and unattended analysis of flowing sample streams in a programmed cycle of operation.

Jan 1, 1965

By F. K. McKean

THE task of establishing a new corrosion testing laboratory is more difficult than it need be because there is very little information on the subject available in the literature. Many articles describing tests and results may be found, but a wide search will unearth only passing remarks on the different types of equipment that may be selected for accelerated corrosion tests. An article describing some of the apparatus needed in a corrosion laboratory should be of help to those interested in building a new unit or in making additions to an old one. In May of this year, the writer was given the assignment of equipping a laboratory for general corrosion testing, to form a part of the new Physical Metallurgy Research Laboratories of the Department of Mines and Resource~ at Ottawa. With the help of senior members of the staff, along with what could be gathered from other sources, a list of necessary equipment was compiled and a plan for arranging it in the rooms was decided upon. Where possible, the apparatus was constructed in the excellent machine shops at the disposal of this Department, while the rest was placed on order with the manufacturers.

Jan 1, 1945

By H. Perez, A. Lavoie, V. Prévost, P. Létourneau, P. Lind

The Home smelter is a custom copper smelter located in Rouyn-Noranda, Quebec. In 2005, the smelter produced 145,000 t of copper containing 807,000 oz of gold, 20,388,000 oz of silver in addition to 515,000 t of sulphuric acid. Recently, a flexible flow sheet has been developed incorporating the intermittent use of the Noranda Continuous Converter allowing for the increasing or decreasing of production based on market conditions, while attaining 90% or greater sulphur fixation regardless of operating mode. For 2006, the smelter is operating in full production mode and production is expected to be approximately 185,000 tm of copper. Mechanical modifications, process changes, metallurgical concepts, minor element treatments, and operational techniques that have allowed the smelter to develop this flexibility are presented. Current efforts to increase the productivity of the converter aisle and anode furnaces as well as improvements being made to address fugitive emissions are also discussed.

Jan 1, 2007

By D. Kulchyski, R. Thibault, D. Lamoureux

"Mine tunneling applications are sensitive to the leakage and friction performance of ducting systems. Improvements in performance can help project economics through reduction in drift height, booster fan spacing, fan electrical power requirement, and deferral of ventilation raise construction. Semirigid plastic ducting has enjoyed significant adoption in mine tunneling in recent years. This paper explores technical properties and performance aspects of this relatively new material application.INTRODUCTIONUnderground mining projects are sensitive to mine development cost and schedule to meet first production—both of which are defined to a substantial extent by mine access construction. The very nature of mine access development requires driving accesses into new areas and even mechanized and automated tunneling methods require ventilation. Until underground airways are connected, allowing a flow-through circuit, ducted ventilation is required to establish ventilation within any single-access (i.e.: dead-end) heading. See Figure 1 as an example of ducted ventilation. Improving performance of ducted ventilation systems impacts project cost and schedule in several ways:For drifts whose height is defined by overhead clearance above haul trucks or tall equipment, smaller diameter ducting will decrease heading size.With higher ventilation flows, activities can be less ventilation-constricted; secondary headings can be worked without restriction, which improves schedule.Given the ability to provide more air for a given fan power, blasting gasses can clear the face and mine more quickly so crews can return to work more quickly - allowing higher advance rates.Lower electrical costs – both due to lower power consumed by fans and with the requirement for fewer electrical stations to power booster fans."

Jan 1, 2019

By A. Elsayed

Lightweight metals such as magnesium show potential in replacing aluminum alloy castings for engine cradles, cylinder heads and transmission cases. Unfortunately, magnesium alloys are susceptible to entrapping oxides and other impurities during casting that hinder strength and ductility. The current study examined various filter sizes and configurations with the aim of improving the mechanical properties of permanent mould cast AZ91E. The unfiltered casting had a yield strength, tensile strength and ductility of 93.3 MPa, 153.3 MPa and 2.2 % respectively and increased to 96.5 MPa, 167.0 MPa and 3.1 % with the use of a fine mesh filter within the well of the mould. The increased strength and ductility was likely due to the filtered castings containing fewer inclusions on their fracture surfaces as compared to the unfiltered castings.

Jan 1, 2011

By L. Zeng, Q. Feng, Z. Qiu, L. Ou, Central South University

It is well-known that the use of nanobubbles can significantly improve the flotation efficiency of ultra-fine particles. However, this is mainly focused on coal and phosphate rock flotation. In the field of nonferrous metal processing, the related research is few. In this paper, a small laboratory mechanical cell associated with a specially-designed nanobubbles generator was used to investigate the effects of nanobubbles on enhancing ultra-fine scheelite flotation. Nanobubbles were created and based on the hydrodynamic cavitation principle through Venturi tubes. Comparative flotation tests were performed using different tubes to evaluate the nanobubbles impact on the ultra-fine scheelite particle flotation recovery. In order to better understand the nanobubbles enhanced ultra-fine scheelite flotation, nanobubbles potential and size distribution were measured. The effect of nanobubbles on the particle aggregation and scheelite particles potential were also studied through the turbidity tests, microscope tests and zeta potential measurements. According to the results, the mean size of nanobubbles was about several hundred nanometers, and the surface of nanobubbles was of highly negative charge in alkaline conditions. The flotation recovery of ultra-fine scheelite particles was increased in the presence of nanobubbles. The zeta potential measurements indicated that the repulsive forces between scheelite particles decreased when nanobubbles existed. Through the turbidity tests and microscope tests, the promotion effect of nanobubbles on particle coagulation could be verified more directly. The existence of nanobubbles in flotation system promotes the particle aggregation, thus increasing particles apparent size and particles capture by bubbles, which may be the fundamental reason why nanobubbles enhance ultra-fine scheelite flotation.

Jan 1, 2016

By MAX VOS

Lithium is the lightest and electrochemically most reactive of all metals. Renewed interest in lithium coincides with research in lithium batteries and power generation by atomic fusion. Ontario lithium resources are contained in spodumene pegmatites that can form where medium- to high-grade metamorphic volcanic-sedimentary formations are intruded by pegmatite and porphyritic granitic rocks. Spodumene pegmatites occur in at least twelve locales throughout northern Ontario, all of which are in the Superior Province of the Precambrian Shield. Tantalum, cesium, rubidium, beryllium, niobium and tin also were noted with lithium in spodumene pegmatites. Considerable potential remains for discovery of additional lithium and rare-element pegmatites in northern Ontario.

Jan 1, 1984

By G. A. Bezuidenhout, J. Davis, S. Lefume, J. P. T. Kapusta, D. K. Chibwe

"Although the centennial of the Peirce-Smith (PS) converting process has recently been celebrated, the technology has essentially not changed much since its inception. PS converting is used extensively in the Cu, Ni and PGM industry to remove iron and sulphur from a molten matte phase. A typical PS converting process would use low pressure air supplied by a blower to bubble air through the molten bath. This bubbling injection regime is inherently inefficient from a process and energy consideration. In the late 70’s and early 80’s, Brimacombe and co-workers demonstrated at both laboratory and plant scales that sonic injection (jetting regime) into copper or nickel converters could reduce or eliminate the above hindrances characteristic of PS converting. Since then, in spite of these successes, very little industrial applications have made headway in the converting process of non-ferrous metal mattes on a commercial scale. As part of its operational improvement and energy reduction program (process efficiency), Lonmin Platinum decided to conduct a full scale industrial evaluation of sonic injection using air only to establish if punchless, high efficiency sonic injection was feasible in its small 3.05 × 4.57 m converters (10’ × 15’). A plant trial was run for four weeks in one of its three converters. This paper discusses the plant demonstration with a focus on the experience acquired by Lonmin together with the key learnings from the trials. Reference will also be made to the commercial aspects of a full scale implementation of sonic injection in all three converters in the smelter. INTRODUCTION AND OBJECTIVESAlthough the centennial of the Peirce-Smith (PS) converting process has recently been celebrated (Peirce and Smith, 1909; Southwick, 2009), the technology has essentially not changed much since its inception. PS converting is used extensively in the Cu, Ni and PGM industry to remove iron and sulphur from a molten matte phase. A typical PS converting process would use low pressure air supplied by a blower to bubble air through the molten bath. This bubbling injection regime is inherently inefficient from a process and energy consideration."

Jan 1, 2012