Search Documents

By A. L. Rutledge, R. S. Nichols

"Waste dump development at the Fording River Operation s in British Columbia began in 1971. In 1981, several unique as well as unplanned situations provided an opportunity to study water flows through waste dumps.The key to the drainage is naturally segregated rock sizes .created by end dumping from the crest of a pile. The largest size material accumulates at the toe. Flow rates along the base of the studied dumps varied from 2,800 to 13,500 m3/day or 0.032 to 0. 156 m3/s (1.2-5.5 cfs}. Sediment concentrations in the water ranged from 1 to 1,800 mg/I.This paper describes water flows through dumps of varied lithology and maturity. The results suggest that neither long-term water flow nor contained sediments in small streams are jeopardized when crossed by end-dumped fills.IntroductionThe Fording River Operations are located in southeastern British Columbia approximately 115 km north of the United State s and 10 km west of Alberta, within the medial range of the Rocky Mountains. All production is carried out at elevations ranging between 1,600 and 2,200 m above sea level.The property is within a continental climatic zone, with temperature extremes of - 40°C in January to +35°C in July. The average annual precipitation of 335 mm of rainfall and 390 cm of snowfall feeds the numerous seasonal, small drainage courses along the Fording River valley.Since start-up in 1971, 149 million bank cubic met res of waste from truck-shovel and dragline mining have been placed in numerous dumps or ""spoils"". The dumps were developed to the point that several unique situations could be studied. During the peak run-off period of May-June 1981, water flow studies were performed on dumps of varied lithology and maturity. This paper describes the results of the study."

Jan 1, 1982

?NWCC has the highest number of Aboriginal students of any post secondary institution in BC and the region served includes 25 bands ? Chair of the Board of Governors is Irene Seguin (Hagwiloo K?am Saxwhl Giis) from Gitwinksihlkw ? FN council ? 39 First Nations Members * focus is to develop policy recommendations to increase student success rates

May 1, 2009

By A. McIntyre, L. R. Plitt

Both the Bond and the Hardgrove grindability tests are widely used in the mineral industry to measure the ease of the comminution displayed by a material. The Hardgrove test is mainly used for coals, whereas the Bond grindabifity test is mainly applied to hardrock minerals. The Bond grindability has the advantage that it can be empirically related to the energy required for comminution (work index), whereas the Hardgrove grindabifity test has the advantage of being easier to perform. In an effort to establish a valid correlation between work index and Hardgrove grindability, a series of parallel grindability tests were carried out on a wide variety of rocks and minerals. The standard Hardgrove test was modified to allow for materials with a higher density than coal. A new, satisfactory relationship was established which permits rapid estimation of work index from Hardgrove test data.

Jan 1, 1980

By Tony Lipiec, Ian Orford

"A key part of plant design is the selection of the design tonnage which is the hourly tonnage target that the equipment selection is based on. Its selection is critical for ensuring that the nominal tonnage which is critical to the financial performance of the project will be met. With deposits being developed at lower grades, higher tonnages and a higher degree of hardness variability, it is essential to ensure that the design process selects the comminution equipment which will be able to deal with the impact of this ore quality variation.Ore hardness and its variance are key factors to be taken into consideration for the selection of the design tonnage. It is well accepted that for the nominal or name plate tonnage to be consistently achieved, it is necessary to base the design tonnage on a hardness value greater than the average ore hardness of the deposit to be mined. The question is how much greater should this design value be to ensure that the nominal tonnage is met to the satisfaction of the project financial model. Standard industry practice is to set the design tonnage by:1. Select an ore hardness percentile that is greater than the average ore hardness to be the basis of the nominal tonnage. Typically either the 75th or 80th percentile value from the data set will be selected.2. Selection of a design factor to multiply by for determining the design tonnage, i.e. the design tonnage = tonnage (based on the average ore hardness) multiplied by design factor.This paper discusses the selection of the design ore hardness through the use of modelling or the use of a design factor. It further shows the impact of ore hardness variance on the capacity of the process and its ability to meet the nominal tonnage. Insight is provided as to what ore hardness percentile value should be selected balancing the shortfalls of tonnage for ores harder than the design value versus the above target production achieved for ores softer than the design ore hardness."

Jan 1, 2016

Once applied, EarthZyme reduces the tendency for a road to exhibit common maintenance issues: wash-boarding, rutting, heaving, potholing and dust.

Aug 1, 2013

By G. Dubé, A. Leclerc, P. Quinn, G. E. Agar, J. Y. Clouthiér, J. D. McLaughlin

"Gold dissolution by cyanide requires the presence of oxygen which is usually supplied by sparging compressed air into the gold containing slurry. For those ores that contain certain obnoxious substances that consume oxygen, maintaining the required minimum level of dissolved oxygen can be troublesome. One of the most economical solutions to the problem of low dissolved oxygen, especially in plants that have air compressors installed, is to enhance the rate of oxygen mass transfer.The oxygen mass transfer rate was measured in a two phase system using two different sparger arrangements, and with addition of a frother that is known to reduce the bubble size produced by the sparger. The common sparger system was shown to be inefficient compared to a readily available but under utilized method of gas dispersion which introduces air directly below the reactor turbine. Transfer of this technology to an operating plant confirmed the beneficial effect of the improved sparger system. The addition of the frother did decrease the bubble size, but it also reduced the oxygen mass transfer rate."

Jan 1, 1993

By P. R. Brito-Parada, G. Bhutani

"The physical processes occurring in flotation columns are very complex as they take place at different scales over a range of sizes and multiple phases. Column design and optimum operating parameters are usually obtained from empirical studies and although progress has been made on its numerical modelling, most column models rely on simplifications that do not fully capture the hydrodynamics. In particular, Computational Fluid Dynamics (CFD) models of the pulp phase in flotation usually assume the bubble population to be monodispersed. While this assumption may be reasonable in some situations, the polydispersed nature of the gas phase can have a significant impact on the predicted flotation rates.Techniques to model size distribution do exist in the literature and have been rigorously analysed in the past two decades for bubble columns, which are very similar to flotation columns from a hydrodynamics point of view. In fact, available CFD models of flotation columns are an extension of bubble column models, sometimes including additional equations for solids treated as passive scalars. This work focuses on the development of an efficient CFD model for flotation columns. The bubble size distribution in the column has been modelled using the Population Balance Equation (PBE), which is solved using the Direct Quadrature Method of Moments (DQMOM). Coupled with the PBE, the multiphase flow equations in the column have been modelled using the standard Eulerian–Eulerian approach. The solution of this coupled system has been made tractable in this work with the implementation of a highly parallelised adaptive-mesh finite element method. This powerful framework has been implemented in the open source CFD code Fluidity and it allows the carrying out of detailed simulations of flotation columns in 2D and 3D, with important implications for industrial column evaluation and design."

Jan 1, 2016

By Jaroslaw W. Drelich

Despite the success of DLVO and extended-DLVO models that have been developed for homogeneous and smooth surfaces, a vast majority of practical surfaces encountered in mineral ore beneficiation are typically rough at various scales; they are also typically heterogeneous. The interactions of gas bubbles with particles having rough and heterogeneous surfaces are much more complex than the commonly used DLVO or extended-DLVO models predict. The effects of surface roughness on flotation and colloidal interactions have been reported many times in the past, although a clear understanding of their origins has been lacking. To explain differences in colloidal interactions for spherical hydrophobic particles, a theoretical analysis of the interaction potential was carried out for a model rough particle interacting with a bubble surface in an electrolyte solution in this study. The attractive hydrophobic interaction potential was added to repulsive retarded van der Waals and repulsive electrical double layer interaction potentials. The rough microscopic particles were modeled as spheres decorated with nano-sized asperities. Parameters that reflect common flotation separation systems were selected for testing this theoretical model and computation of the energy barrier applicable to particle – flat bubble surface interactions. It was found that hydrophobic asperities with the height of only several nanometers can reduce the repulsive interaction energy by an order of magnitude. Theoretical analysis also reveals that surface coverage of microscopic particles by nano-sized asperities is important as well. The findings of this research suggest that manipulating and engineering the particle surface topography could lead to better control over flotation separation.

Jan 1, 2016

By Simon Pelletier, Jose Delgadillo, Dave Page, Pramod Kumar, Raj Rajamani, Dilek Alkac, Martin Fillion

"In general, many past works examine mill load, mill power, shell lifter design etc with a view to improving the mill capacity. On the contrary, only a handful of papers have addressed the transport of fine slurry through the pulp lifters. We present the flow dynamics of pulp lifters via laboratory scale experiments, high speed photography and modeling with computational fluid dynamics. Next, the flow behaviour in ArcelorMittal’s Mont-Wright autogenous mill discharge flow is examined. In an effort to improve mill throughput, a comprehensive simulation and plant scale study of the mill was taken up with a focus on the shell and pulp lifter design. The shell lifter was found to be at its optimum limit for breakage of ore particles given the constraints of wear life and occupied volume. Next, the pulp lifter study was taken up with computational fluid flow code and discrete element code. The simulations directly showed that there was considerable carry-over of slurry. This effect was traced to the area restriction in the pulp lifter channels. Further, crash-stop studies confirmed slurry pooling within the mill. Thus it was readily apparent that mill throughput can be increased if the pulp-lifter could be redesigned. Consequently, the discharger section of the pulp-lifter was redesigned.First, this paper outlines the modeling in laboratory scale studies and plant scale studies leading up to the discharger design. Next, the discharge flow in seven different published mill surveys is predicted with computational fluid dynamics (CFD) methodology shown here. Finally, Mont-Wright mill circuit performance before and after the discharger redesign is described. The usefulness of fluid flow simulations in the design of pulp-lifters is emphasized."

Jan 1, 2012

By M. Saghaeian, R. Hejazi, Sheikhzadeh. V., A. Abazarpoor

"The morphology of iron ore concentrate particles is known to influence several properties of iron ore pellets, including drop number, compression strength, and reduction properties. This study aimed to determine why grinding methods and particle morphology influence green pellet properties. Particle morphology can be directly related to the grinding method: ball mill (BM) or high pressure grinding roll (HPGR). In this research, two iron ore concentrates, namely Gol-e-gohar and Ardakan, were ground by a BM and HPGR to produce a suitable Blaine value for pelletizing (nearly 1,900 cm2/g). Morphological features of particles were subsequently investigated by sieving and cyclone sizing for particle size distribution, the Brunauer-Emmett-Teller (BET) and Blaine methods for specific surface area (SSA) and scanning electron microscopy (SEM) for the evaluation of shape descriptors. It was concluded that HPGR resulted in generating a greater proportion of fine particles compared to ball milling. The BET results showed that the SSA of HPGR pellet feed was higher than that from the BM due to a greater proportion of cracks, indents and bulges and the creation of new fracture surfaces. SEM images processed by ImageJ software indicated that particles ground by the BM tended to be more rounded and less elongated than HPGR particles because of the breakage model of each method. To show the effect of morphology on the green pellet quality, green pelletizing was performed in a pilot pelletizing disc. The HPGR pellet feed had a higher drop number in comparison to the BM pellet feed, due to the angular and rough shape of the particles.INTRODUCTIONThe demand for fine or ultra-fine particles as feed material for ceramics, composite materials, and mineral processing is on the rise (Kotake, Kuboki, Kiya, & Kanda, 2011). The final concentrate of iron ore processing plants (filter cake) has a size range roughly between 0 and 300 µm, depending on the liberation of Fe containing particles (Meyer, 1980). In general, to produce a suitable pellet feed of appropriate quality, Blaine numbers of 1800–2000 cm2/g should be achieved (Van der meer, 2015)."

Jan 1, 2016

By Dave N. K., T. P. Lim

"A fast, reliable and accurate method for radium-226 determination in environmental water samples has been devised, using an alpha spectroscopic technique. The correlation between barium-133 and radium-226 in the barium-radium sulphate precipitation mechanism was studied and in the limited experimental recovery range, the coefficient of correlation was r = 0.986. A self-absorption study for various barium carrier concentrations was also undertaken to obtain the least broadening of alpha energy line widths. An optimum value of 0.3 mg barium carrier was obtained for chemical recovery in the range of 85%.IntroductionWith the increase in uranium mining activities, the migration and spread of radioactivity via various environmental pathways is of great concern. Because of its inherent biological hazard and relatively long half-life, (approximately 1620 years), raidum-226 is frequently monitored as a measure of radioactive contamination of the environment. It is, therefore, necessary to modify existing methods for rapid determination of radium-226 in environmental samples for quick corrective measures in the event of seepage, dam leakage or discharge violations."

Jan 1, 1981

By Michel Ruel, Ali Soltanzadeh

This paper describes how to make advanced control choices when difficult processes need improvement. The decision-making process involves choosing between a rules-based approach and a model-based approach as well as weighing benefits and drawbacks, complexity and simplicity, investment and results. This paper will present briefly each solution: basic control, advanced regulatory control, model predictive control and expert systems such as fuzzy logic controllers and neural networks. Three examples are presented: ARC (Advanced Regulatory Control) on pH in a comminution circuit, MPC (Model Predictive Control) for combustible management and FLC (Fuzzy Logic Control) on a Semi Autogenous Mill. The article then proposes a decision tree for selecting the most appropriate approach. A table will compare usage, development, commissioning, maintenance and lifecycle costs for each approach. Finally, conclusions and suggestions will summarize the methodology.

Jan 1, 2014

By J. P. Rajot, H. Mouzannar, M. Bost

"The design of rock foundations may need to evaluate shear strength of rock-concrete interface by performing laboratory direct shear tests. A series of tests were carried out on specimens for different values of the spacing free of encapsulating material about the shear plane and different values of normal stress. Different kinds of failure were observed and not necessarily at the rock-concrete interface. The spacing free of encapsulating material appeared to be of significant influence on the test results. A mechanical analysis is presented which illustrate the influence of the loading conditions in the direct shear box on the failure mechanism. INTRODUCTIONThe design of rock foundations subjected to significant lateral loads requires defining the value of the shear strength of the interface between rock and cast in place concrete. Verifying the stability against sliding of strip footings subjected to inclined loads (SETRA, 2009) or concrete gravity dams (CFBR, 2013) are common examples where design modelling approaches imply the shear strength, sometimes the deformation behavior, of the rock-concrete interface, more or less assumed as a failure plane.Defining the behavior of rock-concrete interfaces relates to tribology. Many studies have been conducted to improve the representation of this behavior (e.g., Johnston & Lam, 1989; Kodikara & Johnston, 1994; Gu, Seidel & Haberfield, 2003; Saiang, Malmgren & Nordlund , 2005; Fishman, 2008; Eltervaag, 2013; Gutierrez, 2013), raising many questions. The behavior appeared to be influenced by many factors such as the geometry of the interface which is not planar, the roughness of the natural rock, the rock mineralogy and the concrete formulation. In addition, the study of the shear strength of rock-concrete interfaces involves considering the two different deformation behaviors of both rock and concrete. Finally, the observed failure mechanism is strongly influenced by the initial cohesion due to adhesion between the two materials when concrete is directly cast onto rock."

Jan 1, 2015

By Mohamad Sabsabi, André Hamel, André Moreau, Paul Bouchard

"Laser-Induced Breakdown Spectroscopy (LIBS) is an atomic spectroscopy technique used to measure elemental concentrations. It is well-adapted to in-situ and in-line measurements during materials processing in general, and pyrometallurgy in particular. It is an optical non-contact technique and it can measure nearly all elements, including light elements. Our group has developed a mobile prototype system to measure molten metals. The system includes a tube, also called a lance, one end of which is immersed in the molten metal. An inert gas flows in the tube and bubbles out below the surface. The LIBS measurement is made through the tube and onto the bubble’s surface. This is done to avoid measuring contaminants, slag, or fluxes often found at the surface of the melt. An added benefit is that the molten surface is constantly renewed and thus, more representative of the bulk. An alternative to using our lance is to use a tuyère, such as a gas injection tuyère in a converter, as we did several years ago in a nickel matte converter. In this presentation, we will show various applications emphasizing more recent developments. This includes the simultaneous measurement of the concentrations of Cu, Ni, Fe, Co and S in molten matte at 1125 °C. The more obvious industrial applications of the technology include determining the best time to end oxygen blowing in the converter and elemental concentration measurement during alloying.INTRODUCTIONThe mining industry continually faces challenges in optimizing cost and productivity. Because of the large volumes of materials that are being processed, small improvement can have a big impact on benefits. Better real-time information can help improve this optimization."

Jan 1, 2016

By G. Bimpilas, G. N. Anastassakis

"Today, one of the most intense problems in mineral processing systems is referred to the treatment of fine (–100 µm), and even smaller size, particles. Fine mineral particles possess specific properties (small mass, high specific surface area, and high surface energy per unit area) that render their separation inefficient with conventional methods (physical, physicochemical) and equipment. As a result, it is not feasible to obtain a concentrate both of high grade and recovery in mineral value and a considerable amount of mineral fine particles is lost to the tailings. As evidence, we could cite numerous examples from industrial practice with considerable loss of mineral values to the tailings because of the fine particles size, e.g. phosphate, tungsten, tin, etc.The objective of the current paper is to investigate the possibility to separate magnetic gangue minerals and rocks (serpentine, ilmenite, and olivine) from magnesite by co-agglomerating all the gangue components and subsequent magnetic separation of the agglomerates.To meet the target, hydrophobic agglomeration tests were initially carried out on single minerals to define the favorable conditions for selective hydrophobic co-agglomeration of the gangue minerals. In this respect, the effect of the following factors was examined: pH, collector dose, conditioning time, and settling time of the agglomerates. Among the combinations examined, the most favorable proved that with amine in the basic pH region. The use of non-polar oil proved beneficial. The preliminary results were confirmed by tests on mineral mixtures. The application of magnetic separation resulted in the removal of gangue minerals and the recovery of magnesite concentrates of commercial grade (magnesite content 95% approximately) and high yield.The current paper contributes to the development of mineral processing, since it successfully copes with a very important problem of mineral processing, such as the efficient separation of fine particles."

Jan 1, 2016

By G. Russo

During the construction of the S.Martin La Porte access adit, 9m in diameter, extreme squeezing conditions occurred while crossing Carboniferous schistose formations, with diametric convergence up to 2m. Back-analysis of monitoring results shows that an acceptable simulation of the observed excavation behaviour can be derived using a combined analytical and numerical approach, with simple elasto-plastic laws but a progressive reduction of residual parameters and a relevant increase of dilatancy.

May 1, 2009

By Ainul Akhtar, Steve Cockcroft, Daan Maijer, Carl Reilly, Lu Yao, Jun Ou

A coupled thermal-fluid flow-multicomponent model has been developed to aid in understanding the melting/dissolution behavior of solid Al-rich Material (TiAl) in a liquid titanium pool produced by an electron beam. The model is capable of accounting for the significant phenomena present affecting heat, mass and momentum transport including thermal and compositional buoyancy and Marangoni forces, Darcy attenuation, evaporation, melting and solidification, and the associated release or absorption of latent heat. The modeling results have indicated the compositional fluid flow driving forces (compositional buoyancy and Marangoni forces) contribute significantly to the melting/dissolution process. The model is waiting for validation against empirical data.

Jan 1, 2014

By Arsenio Enriquez, Adrian Deneys, Ryan Walton, Jenny Esker

NOx emissions at the Rio-Tinto Kennecott Copper (RTKC) smelter, near Salt Lake City, Utah, are regulated to a compliance emission limit at the Main Stack of 15.9 kg/hr on an annual rolling average. The paper discusses RTKC efforts and improvements, particularly related to the anode furnace operations, since the Smelter modernization in 1995 to comply with the air quality approval limit. This includes replacement of gaseous ammonia to Steam-Gas Refining (SGR) system during the copper reduction stage, upgrade anode furnace oxygen-fuel burner from Praxair’s Stabilized Jet (S-J) to Jet Lance (J-L) technology, development and implementation of operational best practices and continuing to investigate and evaluate NOx control technology and strategy in the industry. In early 2016, changes to Praxair J-L Burner technology on both anode furnaces, utilizing wider lance spacing, was adopted and further improved NOx emission levels well below the compliance limit. INTRODUCTION Since the establishment of the Clear Air Act in 1970, the Environmental Protection Agency (EPA) has been regulating emissions of nitrogen oxides (NOx) to reduce impact on public health and the environment (USEPA, CAA, USEPA, NAAQS). As a requirement of the Clean Air Act, the EPA evaluates the standards for NOx and criteria pollutants on a periodic basis and as a result, standards have been revised and ultimately reduced over time (USEPA, CAA, USEPA, NAAQS, UDAQ, SIP). To remain competitive with changing regulations and in conjunction with Rio Tinto environmental standards for continuous improvement, the RTKC smelter has been motivated to research and implement NOx control strategies. NOx health and environment impacts NOx refers to a group of seven compounds including the most common, nitrogen dioxide (NO2). (USEPA, NO2). The EPA enforces both short-term (1-hr average) and long-term (annual average) standards for NO2 to protect against associated respiratory system impacts. Short-term exposure of elevated NO2 concentrations can aggravate respiratory diseases and lead to symptoms such as coughing, wheezing or difficulty breathing while longer exposures may contribute to the development of asthma and potentially increase susceptibility to respiratory infections. (USEPA, NO2) Additionally, NOx is necessary in the formation of ozone and particulate matter less than 2.5 microns (PM2.5). Ozone concentrations can negatively impact lung function and in some cases, contribute to chronic obstructive pulmonary disease. (USEPA, Ozone) The particles associated with PM2.5 can reduce lung capacity and aggravate heart conditions. (USEPA, PM2.5) For all NOx related pollutants, children and the elderly are generally at greater risk for the health effects. (USEPA, NO2, USEPA, Ozone, USEPA, PM2.5)

Jan 1, 2019

By J. E. Danoczi

Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne area kimberlite field in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as ?gently? as possible since essential to the diamond liberation process is the minimization of diamond damage, particularly for the larger, high value diamonds. The Southern African diamond mines traditionally use Jaw and Gyratory crushers as their primary comminution method. However, these diamond mines generally process the harder, competent kimberlite that is located in the diatreme zone as well as the root zone of the volcanic pipe. Softer kimberlite is typically located in and around the crater area of a volcanic pipe and it is this source of kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills, this being the preferred method of comminution for minimizing diamond damage.

Nov 1, 2011

By René G. del Villar, Jules Thibault, René del Villar

"Some key control variables of industrial processes, associated with product quality, often cannot be measured directly or frequently enough to establish adequate control. In such cases, it is possible to use available measurements to provide a prediction for these process variables and use them in a control strategy, thereby giving rise to what is now commonly called a softsensor.In some industrial grinding circuits, the on-line particle size analyzer is shared between various sampling points. Therefore, for a given location, the actual measurement is only available every 10 to 20 minutes, a delay which is unacceptable for automatic control purposes. To alleviate this problem, a softsensor based on an artificial neural network has been investigated. First, the structure of the neural network and different schemes for the training process are analyzed. Then, the performance of the neural network softsensor is compared with other inferential methods such as ARMA models and Kalman filters.IntroductionGRAHM, French acronym of the Research Group on Computer Applications in the Mineral Industry at Laval University, began in 1990 a research project on Knowledge Based Automatic Control (KBAC). This project, sponsored by a consortium of eight mining companies and the federal and provincial governments, seeked to screen advanced (knowledge-based) methods for data processing (filtering, mass balancing, etc) and automatic control (model-based) for their use in the mineral processing operations and the transfer of the project results to the sponsor companies.In parallel to more academic research work, a number of case-studies have been undertaken with the cooperation of partner companies. Among such works, a very successful one has been the design and installation of a new control strategy for one of the Kidd Creek (Falconbridge Ltd.) grinding circuits. This project was related to the evaluation of a number of control strategies and the implementation of one of them, as selected by the plant management, in the concentrator.A total of sixteen control schemes were evaluated on one of the dynamic phenomenological simulators developed at GRAHM, a trademark of this research group [ l]. The calibration of the simulator models was done based on industrial data gathered by GRAHM and Kidd Creek personnel. Then, the simulator was used to test the performance of various PID-based control schemes, designed to achieve the control objectives set by the Kidd Creek personnel. The best scheme proposed called for controlling the cyclone overflow particle size by manipulating the water addition rate to the cyclone feed box and the circulating load by manipulating the circuit ore feed. The particle size analyzer (PSI-200) available for monitoring the product size, was unfortunately shared (multiplexed) among various streams of the plant, which meant a 14 min delay between two consecutive readings for any particular stream. This induced the plant personnel to choose an alternative control strategy, one which controlled the cyclone feed density instead of the cyclone overflow particle size."

Jan 1, 1996