Search Documents

"The Upper Mannville unit commonly consists of interbedded marine and non-marine sands and shales, but in northwestern Alberta the unit consists of marine shales of the Spirit River Formation. A thick tongue of marine shale (Clearwater Formation) ex-tends eastward into the Athabasca area below sandy Grand Rapids beds. Correlation of Upper Mannville rocks to the southeast is difficult, but in the Cold Lake area a thick sandy depositional cycle (Mannville ""C"" of this paper) appears to be approximately correlative with the Clearwater Formation. In the Lloyd-minster region, tongues of marine sedimentary rock occur in the lower part of the Upper Mannville unit. Most of the Upper Mannville oil occurs in the Grand Rapids Formation at Wabasca, in the thick ""C"" unit and younger Mannville sands at Cold Lake, and in the Sparky and General Petroleums sands of the Lloydminster region (Figure 2).The Lower Mannville unit was deposited on an erosional surface of considerable relief that truncated the Jurassic and older strata of the Western Canada basin. Continental, probably fluviatile, sedimentation persisted over much of the Western Canada basin during deposition of the Lower Mannville unit, but an Arctic or Boreal sea lay over part of northern Alberta. At the end of the depositional episode, the sea transgressed southward and eastward (Figure 3) and re-worked the Bullhead and McMurray sands of northern Alberta into the glauconitic Bluesky and Wabiskaw sands. Topography on the sub-Cretaceous erosion-al surface had a considerable effect on the deposition of the Lower Mannville (Rudkin, 1965), and the highest hills on this surface were not completely on-lapped by Lower Mannville sediments (Figure 3). The coarser elastic material was derived both from a western Cordilleran region and from an eastern Canadian Shield region (Glaister, 1959, p. 620; Mellon, 1956)."

Jan 1, 1966

By W H. Poole, E. R. W. Neale

A new style of tectonic map based on age of folding has been prepared for the Canadian Appalachian region as part of the Tectonic Map of Canada Project. This style of map pro-vides a clearer picture of the tectonic history of the region than any meth-od hitherto attempted. Precambrian blocks that were relatively unaffected by Palaeozoic de-formation are distinguished on the Great Northern Peninsula and in the Conception Bay region of Newfound-land. K/ A age determinations suggest that these blocks were intruded and metamorphosed during Grenville orogeny. Other Grenville-like rocks, on Cape Breton Island and in New Brunswick, were more actively involved in subsequent Palaeozoic orogeny. Taconic orogeny, the first phase of Palaeozoic deformation, took place in Middle and/or Late Ordovician time and was accompanied by intrusion of ultrabasic rocks. Evidence of the -

Jan 1, 1961

By H. J. Rowley

THERE are many varieties of limestone, but for the general purposes of the pulp and paper industry, two classifications are sufficient: (1) High-calcium stone, which should be quite free from impurities and contain not less then 90 per cent calcium carbonate. (2) High-magnesium stone, containing not less than 25 per cent of magnesium carbonate. Before proceeding with detail on the use of limestone and lime in the industry, a few words regarding the pulp products made in Canada are desirable. By far the largest tonnage is made by grinding spruce and balsam logs on rotating sandstones or on artificial abrasive stones of the Norton or Carborundum types. This mechanical or groundwood pulp finds its largest use in the production of newsprint paper, of which it comprises about 80 per cent of the total fibrous substance employed-the remaining 20 per cent being unbleached sulphite pulp. No limestone or lime is directly employed in making groundwood pulp, as contrasted with the chemically prepared pulps, all of which require one or the other form of the base for their processing. Sulphite pulps comprise the next largest tonnage group. They are produced by boiling, under pressure and at elevated temperatures, spruce and balsam wood in chip form in solutions of bisulphites and sulphurous acid. The usual bisulphites employed are those of calcium and magnesium. Sodium, potassium, and ammonium bisulphites give progressively better pulps, but to date, in the absence of efficient recovery methods, cost has precluded their use.

Jan 1, 1939

By C. G. Williams

IN preparing this paper on Canadian mine taxation, there has been no attempt to detail the requirements of the various taxing bodies; but rather to consider the matter from the standpoint of its underlying principles and give a general idea of the methods adopted. I have added an Appendix setting forth the principal features of the various Acts, which should be used for general reference only, since new rulings alter minor details from time to time. In current legislation, many important points are left to the discretion of the Ministers and their deputies. We are, indeed, fortunate in having in Canada an able and conscientious body of permanent officials, who bring a sense of justice and courtesy to their work which is most commendable, and which has done much to simplify the working out of general problems. The production of metals may rightly be deemed a form of manufacture, but differs from the average manufacturing business in three important respects: (1) In its early stages, it is wholly speculative, since it is impossible to make any definite appraisal of value or possibilities. (2) The principal asset of any mine, i.e., the ore in the ground, is a wasting asset, and is irreplaceable. (3) Any additional burden by way of taxation cannot be passed on to the public but must be borne entirely by the producer. Having regard to the first of these differences, it is apparent that, since the risk of loss is great, the reward in case of success must be correspondingly great. This fact seems to be constantly overlooked by those who regard the all too few outstanding successes in Canadian mining history as fit prey for predatory legislation. As an illustration of the speculative nature of early mining development, let us consider the Province of Ontario-and I take this illustration simply because I am more familiar with conditions there, and not because I believe it differs greatly from any other province. From 1907 to 1933, 165,243 claims were staked and recorded, from which 43 mines were developed which paid one or more dividends. There was, of course, some duplication through re-staking; also, on some claims very little work was done, and most mines have more than one claim. But, since staking and recording cost real money and effort, each of these claims must have been considered to have had merit.

Jan 1, 1935

By H. S. Wilson

"The property owned by the Lamaque Mining Company comprises a group of forty-four claims and fractions occupying an area of about 2,458 acres, in west-central Bourlamaque township, Abitibi county, Quebec. It is on ,the outskirts of the towns of Bourlamaque and Val d'Or, about 70 miles east of Noranda, near the eastern end of the belt of greenstones of Keewatin and Timiskaming age that extends eastward through Kirkland Lake into northwestern Quebec, terminating in Haig and Jurie townships 40 miles to the east.The claims on which the orebodies occur were first staked in 1923; No. 3 vein was discovered the following year. The original discovery was made by R. Clark in 1923. This was a small quartz vein containing a pocket of coarse gold on the north side of a hill near the northwestern corner of block 3. It is said that all the gold was removed in one shot in blasting into the vein; elsewhere it was barren. A picket line was then run west along the strike of the vein, which occupied a narrow shear zone, and about 2,000 feet west, in prospecting on either side of the picket line, a large boulder of quartz and tourmaline containing visible gold was found. This led to more intensive prospecting by trenching in the vicinity with the result that the No. 3, or 'float' vein, about 250 feet north of the boulder, was found. Due to low ground this vein was exposed in only one trench. The only other important vein found on the surface was the No. 1, or H, vein, which was exposed in several places by stripping and trenching, but it did not carry appreciable amounts of gold."

Jan 1, 1954

By G. O. Oniyide, H. Yilmaz.

"This paper presents the result of the research done on the effect of temperature on the dilatancy of rocks from the Bushveld Igneous Complex (BIC), where the South African Platinum mines are located. The BIC has higher virgin rock temperature (VRT) than the gold mines of the ‘Witwatersrand Basin Complex’. If the platinum mines advance to ultra-deep levels as the gold mines, since the Merensky Reef has been reported to extend beyond 5km, then the virgin rock temperature at 5 km below surface would be approximately 140oC. Hence, there is a need for the investigation of rock behaviour at high temperatures. Five different rock types (norite, leuconorite, mottled anorthosite, pyroxenite and chromitite) were tested in a 2600 kN servo-controlled multi-purpose triaxial testing machine. The tests were done at a constant strain rate of 5 x 10-1 S-1 and a confining pressure of 10 MPa within temperature range of 20 °C (ambient temperature) to 140 °C. The results show a general strength reduction and increasing dilation angles with increasing temperatures. The results also demonstrate that dilation angle is close to the internal friction angle at lower temperatures; however, they are greater at higher temperatures.INTRODUCTIONMany challenges are faced with increasing depth of mining in underground mines. The most obvious are heat, in-situ stresses and those associated with logistics. Issues related to underground heat have mainly focused on the side effect of heat on workers' health, increasing production costs as a result of higher cost of ventilation. The effect of increasing temperature with increasing depth on the behavior of rock has not been given much consideration. Generally, gold mines in South Africa are deeper than the platinum mines but the latter have higher temperature gradient, which makes the platinum mines to be warmer at similar mining depths. Although the study of the effect temperature on the behaviour of rock can be beneficial to both gold and platinum mines, the focus of the research is limited to the platinum mines because of their higher temperature gradient. Donoghue (2004) stated that the virgin rock temperatures (VRT) and air temperatures increase with depth, due to the geothermal gradient and auto-compression, that is, compression of air by its own weight."

Jan 1, 2015

By D. W. Boydell

The response of reclaimed gold tailings to acid leaching was investigated in the laboratory, followed by a pilot-plant program in which the operations of CCD, CIX and SX were tested with plant feed material. These results formed the basis for the design of the extension to the existing uranium plant at Blyvooruitzicht Gold Mine, commissioned in July 1977. This circuit consists of slimes-dam reclamation by bucket-wheel excavator at a rate of 100,000 t solids per month, acid leaching in pachucas, a five-stage CCD washing section, two parallel C1X absorption columns and two elution columns, SX and an ADU precipitation section. Barren solution is recycled to the CCD section as wash and to the repulper at the slimes dam. The performance of the plant during the first year of operation is compared with the predictions on which the plant design was based. Rated capacity was achieved within three weeks of start-up at a nominal dissolved uranium recovery in the ion-exchange section of around 98%. Owing to recycle, the over-all recovery in the ion-exchange and solvent extraction sections is somewhat higher than this figure.

Jan 1, 1979

By G. I. Mathieu

"An experimental study was carried out to evaluate the performance of column flotation versus conventional flotation for the recovery of molybdenite from a Newfoundland ore. The objective was to verify the claims made by the inventors of the flotation column, Messrs. Pierre Boutin and Remi Tremblay, that their apparatus reduces the entrainment of fine gangue and other mineral impurities in the froth product. The research included a factorially designed series of tests to determine satisfactory operating conditions of the column. These provided a basis for comparative flotation tests with column and Denver cells. In the course of the work, the action of a few depressants was studied. Results indicated greater selectivity in the column and reduced reagent consumption."

Jan 1, 1972

By K. Hanumantha Rao, A. Javadi

Our recent studies revealed that the sulfide minerals in contact with water during grinding produced hydrogen peroxide (H2O2) where the amount of H2O2 production by the minerals found to be in the order of pyrite > chalcopyrite > sphalerite > galena. The H2O2 effect on the oxidation of pulp components and its influence on the concentrate grade and recovery in flotation have been studied and the results have been presented and discussed in this paper. Studies have also been carried out to build correlation between percentage of pyrite in the concentrate, grinding conditions and concentration of OH•/H2O2 in the pulp and as well of controlling the formation of these species through known chemical means for depressing the generation of the oxidant. Flotation tests using a complex sulfide ore with the same reagent scheme that is being used at Boliden concentrator in Sweden but with the addition of i) collector and depressant, ii) Na2S reductant and iii) inorganic (EDTA) and organic (TETA) surface modifiers, during grinding stage have been performed to judge the beneficial or detrimental role of H2O2 on the selective flotation of sulfides. The results demonstrate that the selectivity of metal sulfides against pyrite increases with increasing generation of H2O2 in the pulp liquid. H2O2 is also found to be a better oxidant in chalcopyrite-galena flotation separation than the commonly used K2Cr2O7.

Jan 1, 2016

By David McMullen

Radiation plays a critical role in the thermal behaviour of hydrometallurgical process equipment. This effect is particularly important when designing refractory lined equipment used in pressure leach/oxidation processes. In order to simplify this non-linear mode of heat transfer, the effects of radiation had previously been incorporated in an equivalent convective film coefficient in finite element methods (FEM). This prior method omits the effects of radiosity, a critical aspect of radiation heat transfer, which affects the design of refractory lining systems in autoclave vessels. Given that 60% of the heat loss in actual plant practice of an autoclave is due to radiation, reliability in the FEM is therefore impacted. This study validates the use of radiosity in FEM through thermal loading using a combination of simple geometries to be applied to complex environments such as vessel nozzle clusters. The added benefits of using a radiosity load includes an increase in confidence in thermal distribution results, greater accuracy in determining appropriate refractory lining systems, weld overlay sizing, and increased accuracy in structural analysis.

Jan 1, 2014

By M. van de Vijfeijken

This paper will first give a short overview of the Copper Mountain project in British Columbia, which just has started commercial operation earlier this year. The grinding process with one 34' x 20' SAG mill and two 24' x 39.5' ball mills will be briefly discussed. All three mills are gear driven by a ring gear, dual pinion and two low speed synchronous motors. Copper Mountain has installed on all three mills, the new state-of-the art dual pinion mill drives. All the inherent operation and maintenance features of this drive technology will be discussed, as well as the advantage of having variable speed control also on the ball mills. The installation and commissioning of the mills and drives at Copper Mountain will be briefly reviewed. Finally the first field measurements on these low speed mill drives will be presented, with the main focus on the low mechanical stress impact of these mill drives on the pinion and ring gear, as well as the accuracy of the load sharing between the two motors.

Jan 1, 2012

By G. Gu, B. Fang, R. W. Revie, M. Elboujdaini

Electrochemical behavior of an X-80 pipeline steel, including frequency-sweep electrochemical-impedance spectroscopy (EIS), time-sweep EIS at a constant frequency and open-circuit potential (OCP) monitor, was investigated using four-point bending specimens subjected to a stress-corrosion cracking (SCC) test in a near-neutral pH environment. The capacitive loop became smaller with test duration, revealing an increase in the corrosion rate. The resistance obtained in the constant-frequency EIS test showed two regions, of which the region with a remarkable decrease in resistance transformed into a region of slow decrease, whereas the capacitance increased with test time indicating that iron dissolution was fast at first, and then a corrosion product or film formed and covered the surface, leading to the pitting formation.

Jan 1, 2005

By J. J. Denny

IN a preliminary paper (1) it was shown that the addition of small quantities of metallic aluminium powder almost completely inhibited the solubility of siliceous material in the beaker. Six rabbits exposed to quartz dust for six months all showed well developed silicosis. Seven rabbits exposed to quartz dust plus 1 per cent metallic aluminium powder for the same period did not develop silicosis. At that time, we were not in a position to state either the manner in which metallic aluminium reduced the solubility of siliceous material, or, from the animal experiments, whether the aluminium was acting locally or systemically, or for what period after the cessation of dusting it would continue to act. This paper reports the further progress of this investigation. CHEMICAL EXPERIMENTATION The technical details pertaining to the various substances used in the experiments are given in an appendix which is on deposit with the American Documentation Institute, Washington, D.C. For lack of space, it is not printed here. The term 'solubility' is used to indicate the concentration of silica in the solution under the conditions as noted, determined colorimetrically (2), and expressed as parts per million (p.p.m.). The term 'reduction in solubility' indicates the difference between the solubility of the .silica in the presence of the aluminium powder and its solubility in the absence of aluminium powder. It will be noted that the solubility figures for different samples of quartz with no added aluminium vary considerably. The figures do not refer to an equilibrium solubility of silica but to the actual amount of silica dissolved from a given sample in a given time at a given temperature. In view of the fact that quartz dissolves extremely slowly, it is evident that the actual figures in any case will depend upon the surface exposed, i.e., fineness of grinding of the different samples.

Jan 1, 1939

By The Staff

Introduction In this paper it is proposed to discuss briefly some of the problems confronting the management of a gold mine in choosing a method of milling to recover the gold from various classes of ore. In order to simplify the discussion, the more common types of gold ores are classified from a metallurgical point of view as follows: Class 1?A: Free-milling ores which require only relatively coarse crushing. B: Free-milling ores which require finer grinding to release the gold. Class 2?A: Gold ores which contain the gold partly in the flee state and partly associated with a small amount of iron sulphide, and which do not require fine grinding. B: Gold ores similar to 2A, but which require fine grinding. Class 3?A: Gold ores containing copper in quantities insufficient to interfere to a serious extent with cyanidation. Gold ores containing copper in sufficient quantity to interfere with cyanidation but in which a large proportion of the gold is in the free state, the remainder being chiefly associated with the copper mineral, chalcopyrite. Gold ores containing copper and other sulphides, such as pyrite, etc., in which the gold is principally associated with these sulphides.

Jan 1, 1931

By Laxman M. Amaratunga

Laboratocy flarmnability tests were perfonned on dust samples from Fraser Mine in a 1.2 L Lindenburg horizontal tube furnace to detennine the percentage of sulphur oxidized during ignition. The explosion pot ential of sulphide dusts depends on their degree of spontaneous oxidat ion, which was measured by the quantitative analysis of so2 gas released during ignition. Test results indicated that dusts with low sulphur content could exhibit a higher degree of oxidation than a sample with high sulphur content. txlst characterisation using image analysis techniques suggests that the structure and the texture of dust are important factors influencing the explosibility of sulphide dust at ignition temperatures. Therefore for safe mine operations% sulphur content cannot be considered as a reliable single index that could be used to predict the potential of a sulphide dust explosion. Physical, chemical and mineralogical characterisation of dust plays an important role in the detennination of suitable indices for the prediction and prevention of sulphide ore dust explosions.

May 11, 1988

By W. W. Rudolph, L. N. Trevani, P. R. Tremaine

UV-visible spectroscopy, Raman spectroscopy, and vibrating tube densimetry have been used in our laboratory to determine equilibrium constants of aqueous species at temperatures as high as 325 °C. The UV-visible and Raman spectra of solutions containing metal complexes and ionized acids or bases can be used to yield formation constants by applying curve fitting methods to resolve the contribution of each species. Colorimetric pH indicators identified by Johnston and coworkers at the University of Texas (Austin) provide an alternative means of determining ionization constants and the pH of complex mixtures. High precision density measurements over the same range yield standard partial molar volumes, which are key parameters for "equations of state" for aqueous species. Examples are given for the copper-ammonia system, simple carboxylic acids, and the iron-sulphate system.

Jan 1, 2004

By A. S. H. Kabir

Due to the high specific strength and excellent corrosion resistance, Ti-6A1-4V has been widely applied in aerospace industries. In this study, the welding performance of 3.2-mm and 5.1-mm thick Ti¬6A1-4V sheets was studied using a 4 kW continuous wave Nd: YAG laser. It is found that the use of filler wire, matching the parent metal composition, can bridge the joint gap and produce full penetrated welds up to a width of 0.6 mm without cracking. The laser welds were characterized in terms of the bead geometry, defects, microstructures, and hardness. With increasing joint gap, the percent porosity area increased, reaching just over 1% of the fusion zone area at a gap width of 0.6 mm for the 3.2 mm and 5.1 mm thick sheets. The maximum underfill depth in the Ti-6A1-4V laser welds was about 5% or 7% of the sheet thickness for the 3.2-mm and 5.2-mm thick materials, respectively, meeting the AWS D17-1 specification. The microindentation hardness was maximum in the fusion zone and sharply decreased through the heat affected zone until reaching the base metal value.

Jan 1, 2011

By A. Gourlie

"This paper describes the performance properties of a new 95 ksi minimum yield strength, oil well casing grade designed specifically to resist hydrogen sulphide stress corrosion cracking, SSCc. The new grade, Soo-95SS, demonstrates NACE Tensile threshold values greater than 90% specified minimum yield strength, SMYS, and NACE Bent Beam values in excess of 12.7 x 1()4 psi. The new Soo-9588 grade also exhibits superior collapse and notch toughness values. IntroductionIn recent years, a trend toward casing grade specialization has resulted in the introduction of numerous proprietary grades designed specifically for particular production environments, In response, Algoma Steel has developed, as part of a "" grade for service"" philosophy, two new 95 ksi minimum yield grades. The two grades are Soo-95, High Collapse (HC), and Sour Service (SS). This paper describes the development of Soo-95 Sour Service.Four main objectives were established:1. Definition of the steelmaking and continuous cast processing practices2. Determination of the acceptable maximum and minimum levels for all chemical elements3. Definition of special processing requirements4. Definition of the physical characteristics and ranges of the product properties.This paper provides a description of the experimental approach, followed by a presentation and discussion of the trial results . Finally, a number of conclusions are given."

Jan 1, 1988

By W. Cholewa, T. S. Golosinski, J. Wedzicha

"Power requirements of belt conveyor drives are usually estimated based on the calculated belt tension which equals the sum of unit resistances to motion which the belt has to overcome. In most situations, the value of various unit resistances can be accurately predicted using published information (5,6,8,12). A simpler approach calls for use of standard formula and tabulated values of related factors which reflect various features of both the conveyor and the transported material (2,3,7) . None of these approaches is reliable when materials with unique properties are conveyed, nor if applied to conveyors working in extreme climatic conditions. Such is the case of oil sand mines in northern Alberta.There the bitumen content of oil sand causes it to behave in a unique manner. Furthermore the conveyors operate year around, with winter temperatures often lower than - 40°C. It was the objective of presented investigations to quantify the power requirements of conveyors, and related resistance to motion for the conveyors used in oil sand mines during winter operations.The other objective was to quantify the drive power requirements of oil sand conveyors during start-up. These requirements are usually much higher than those during norm al operation, and their quantification is of paramount importance for operation of large conveyors."

Jan 1, 1992

By P. O. Sandvik, George Erdosh

"AbstractThe Cargill phosphate deposit, located 32 kilometers southwest of Kapuskasing, Ontario, was discovered by the Resource Development Group of International Minerals & Chemical Corporation in 1975 and has been evaluated through an extensive program of 190 drill holes, numerous chemical analyses, metallurgical tests, and engineering and economic studies.The Cargill alkalic complex, comprising principally car-bonatite and pyroxenite-amphibolite rocks, was intruded in to the rift system of the Kapuskasing High during late Precambrian time about 1,800 million year s ago, near the intersection of northeast- and northwest- trending faults. The Cargill complex is one of at least ten known alkalic complexes in or close to the Kapuskasing magnetic-gravity-high system and is expressed by an elongated, northeast- oriented, three-part magnetic anomaly 7.2 kilometers long by 2.8 kilometers wide . Weathering and leaching under assumed temperate to cool, moist climatic conditions , and controlled by faulting, shearing and/or initial petrographic variations within the carbonatite , developed a small, locally confined karst system in the car bonatite rocks and resulted in a thick enriched leached carbonatite zone, capped by troughs and sinks, filled with a residuum of apatite, goethite, clay and other minerals stable in the near -surface, oxidizing environment. Overburden is 5 to 165 meters thick."

Jan 1, 1977