Search Documents

By Barry J. Turley

With over 700 large electric-drive haulage trucks operating in Canadian mining today and over 3700 in mines worldwide, most aspects of electric drive are well known. Recently, however, extensive application of these trucks to down-hill hauling in mountain mining makes it vitally important that many of us better understand the operation and proper application of the dynamic retarding feature of these vehicles. This paper is an attempt to clear up misunderstandings on this subject, to suggest precautions that mining operators should take in comparing competitive retarding systems and to challenge equipment manufacturers to evolve improvements to the important aspect of system performance.

Jan 1, 1978

By W. Beres, R. E. Miller, B. Shiari, L. R. Zhao

A dynamic multiscale simulation method has been developed to study the material scratching processes on nanoscale single crystals. The model simultaneously captures the atomistic mechanisms near the free surface and the long range mobility of dislocations and their interactions, without the computational cost of full atomistic simulations. The method also permits the simulation of system sizes that are approaching experimentally accessible systems, albeit in 2D. Simulations are performed on single crystal aluminum to study the atomistic details, surface evolution, and generation and propagation of dislocations for a variety of scratching depths at room temperature. Simulations demonstrate the power of the developed method in capturing both long-range dislocation plasticity and short-range atomistic phenomena during tool advance. Variations of scratching normal and tangential forces are investigated and related to plastic deformation and dislocations generation during the simulation process.

Jan 1, 2006

By D. D. Liu

This paper proposes a charge induction dust measurement method based on detrended fluctuation analysis (DFA) for use in coal mine environments, based upon electrostatic interference, dust properties, wind speed, particle size, moisture content and other factors. In this methods, sequence x(t) is first obtained through a dust concentration sensing probe, and then the cumulative deviation y(t) is calculated, and y(t) is divided into same lengths. Secondly, a first-order linear fit is used for data of each interval, and mean-square deviation filtered DFA was calculated for each interval. Finally, the dust mass concentration of the corresponding time is obtain by supplemented calibration coefficient and fitted the data point which is the mean and square root for all lengths of interval. Simulation and verification experiments showed that the charge induction dust measurement method based on DFA can reduce coal mine electrostatic interference effects with high accuracy. The design has been successfully applied to select areas.

Aug 1, 2013

By Makhlouf Boubahziz

The HNIA field is part of the Tinrhert project which consists of developing 17 fields containing essentially gas with a few small rings of oil. It is considered as one of the main fields in this project in terms of its area and the number of geological structures that has formed it. It is a wide anticline of Cambro-Ordovician age, orientated NNE-SSW and located in the South-eastern part of Illizi basin. This structure extends from Alrar-center in the North, to the North of In Amenas in the South. The area is 1350 km2. The main reservoirs forming HNIA field are the Devonian (F2, F3 and F4), Siluro-Devonian (F6) and Cambro-Ordovician. These latest are formed by 4 sandy units alternated by layers of shale and shaly silt termed from the base to the top as follow: Unit II, Unit III-3U, Unit IV-2L and Unit IV3; these units are the subject of this study. The HNIA field is essentially gas, up to day this field is at the stage of appraisal and evaluation in order to establish a development plan; therefore the main target of this study is to contribute to this frame work. The following objectives are: ?To build a structural model of the study area. ?To integrate all the sedimentological, structural and petrophysical data in order to build a 3D geological model

Aug 1, 2013

By Reik M. Winkel

Radar Technologies are successful implemented in the military industry since decades and recently found their way in the mining industry as level gauge radars for bin applications. The latest generation of microwave radar sensors are capable to provide geometrical data of the surrounding area of mining machines, too. Radar sensors are an improvement to laser scanners as they are more robust and able to penetrate dust and mist. Radar sensors will be the key source for operator assistance systems. indurad and RWTH Aachen University conducted a large series of tests at open pit mines and underground coal mines to determine the potential of the new two dimensional Dual Range Radar iDRR. Several applications were determined as highly feasible and are now completed respectively in the implementation stage. The authors are giving an insight in the experimental results, the implementation and an outlook of future applications for this technology.

Oct 1, 2009

By G. J. Desroches

"In order to improve zinc plant productivity, areas of low efficiency were identified. As a result, solution purification was improved, additional dust precipitator capacity was made available and a new zinc casting plant was installed. The effects of these and other changes are discussed and the expenditure and benefits reviewed. HistoryThe operation of the Flin Flon metallurgical complex including an electrolytic zinc plant commenced in October 1930. The design of the zinc plant was based on that of the Commonwealth Mining and Smelting Company at Trail, British Columbia, the Anaconda Great Falls Montana Plant and the Electrolytic Zinc Company plant at Risdon, Tasmania.The plant began with a design capacity of 60 tons per day and currently produces 255 tons per day. Since plant start-up, approximately 3.5 million ton s of zinc metal have been produced, most of it exceeding special high-grade specifications.IntroductionThe facility incorporates the basic process steps of roasting, leaching, purification, electrowinning and casting. Figure I details the flowsheet. During the late 1970s, management recognized that in order for the zinc plant to continue operating, it was necessary to introduce cost-effective practices.Study groups, consisting of design engineers and operations personnel, were formed to investigate the details of plant revisions.The objectives were to improve productivity by reducing manual labour, reducing energy usage, increasing zinc recovery, increasing metal output and reducing costs.This paper details the changes made during the period 1979to 1986 and shows how these changes have affected the productivity and economics of the zinc plant operation."

Jan 1, 1988

By H. Warren Newcomen, Dennis C. Martin

"This paper describes the investigation of a large, progressive slope failure on the southeast wall of the east pit at Highmont Mine, British Columbia Geotechnical investigation s consisted of geological and structural mapping, assessment of blasthole drilling records, review of rock core information, slope movement monitoring and back analysis of various possible failure modes. Climate records and mining history were also assessed to determine their relationship to slope movement .Analysis of movement monitoring records and geotechnical information indicates that the failure is deep seated. The upper portion of the failure surf ace occurs along clay filled discontinuities. The lower portion of the failure surf ace appears to occur through the highly altered rock mass. High groundwater pressures and mining at the toe of the slope are documented to have had a major influence on stability at various times during the failure. Stability analyses results are presented and possible remedial measures are discussed.IntroductionHighmont Mine is located near Logan Lake in the Highland Valley approximately 50 km southwest of Karnloops, British Columbia (Fig. I). Mining of the porphyry copper and molydenum ore bodies began in 1980. In May, 1983, when mining in the east pit had progressed to a depth of about 60 m (200 feet) , a failure (designated the Southeast Failure) began to develop in the southeast corner of the east pit. Subsequent mining to a depth of 110m (360 feet) was accompanied by frequent and substantial slope movements involving between 500000 and I 000 000 m3 of rock . The slope was monitored extensively to assess short-term movement trends for operational safety. Geological mapping, core logging and rock mechanics testing were used in conjunction with the long-term monitoring information to determine the failure mechanism, conduct stability analyses, assess the effects of instability on pit design and enable design and installation of remedial measures."

Jan 1, 1988

By A. G. Matyas, B. Wasmund, R. C. Francki, K. M. Donaldson

"The construction of large. high-power electric furnaces has been an important factor in the growth of electric smelting technology . New developments in the design and operation of electric furnaces have been spurred by the escalating cost of electric power and increasingly stringent environmental constraints. Key areasofprogress include the application of high voltage to enhance furnace productivity; the installation of novel furnace cooling elements and robust binding systems to extend furnace life; development of process schemes to reduce power consumption by preheating and prereduction of the charge; and environmental control improvements for handling fine dusty feedstocks, and for furnace sealing.This paper reviews these developments and outlines a systematic approach for their application in the custom design of new or retrofit electric furnace facilities.IntroductionThe use of electric smelting furnaces has continued to progress during the last decade. Electric furnaces offer high throughput capacity and productivity. In addition, they produce minimum environmental impact, as the furnaces can be readily sealed, and only a small quantity of off-gas is generated. Electric furnaces present the most favourable choice of smelting technology where high process temperatures in excess of about l400°C are required.Their application is burdened by the escalating cost of electric power, hence it is important to seek new opportunities through further technological development. This paper reviews recent developments in the design and operation of high-power electric smelting furnaces, in the following areas:"

Jan 1, 1993

By Zygmunt Wegrzyk

Poland is rich in hard and brown coal reserves, which have become the most important, and steadily developing, primary source of energy. With 192.6 mill. t of hard coal production and 40 mill. t of exports in 1978, Poland is fourth and second in the world respectively. The paper discusses the various mining methods adopted in the country's history of mining. Particular emphasis is placed on longwails, their mechanization and equipment assembled in the form of fully mechanized face complexes suited for varied geological conditions. Measures to improve the recovery ratio of coal resources are dealt with. investment efforts undertaken in the coal industry are outlined. An account is given of the ever improving techno-economic results of coal mining. The country also exports a wide range of mining equipment and transfers its well-founded technical know-how to others. There are strong cooperative links with many foreign partners.

Jan 1, 1979

By M. C. Ethier, A. L. Laramie

"The Granisle and Bell Copper mines were officially put into production in 1966 and 1972, respectively. The Granisle Mine was purchased in late 1979by Noranda and the two operations were amalgamated as one division. Both mines were closed in 1982after sustaining heavy financial losses during a period of low copper prices beginning in 1981.This paper describes the resumption of operations at the Bell Mine in 1985 after its shutdown period of three years and the dramatic and sustained improvements in productivity and efficiency realized as a result of a commitment by employees and management to the application of Participative Management and Employee Involvement principles. After a general description of the effects of such a philosophy on the operation as a whole, and a comparison to the operation's last full year as a producer, it deals with the practice of this philosophy in the maintenance department at the Bell Mine and the superb results realized.IntroductionThe Bell Copper deposit was discovered in 1963 and came onstream as a 10000 ton s per day open pit mine in the fall of 1972. Identified reserves at that time were 46 million tons of ore containing 0.50% copper. The mine shared facilities of the townsite of Granisle with the nearby Zapata-Granby mine which had established the community six years earlier.Because of easy grinding ore and improvements to milling circuits, Bell's throughput rate was increased to 17 000 tons per day by the late 1970s. In the open pit, improvements resulted in mining of additional reserves with higher stripping ratios. At startup, a half ton o f waste was mined for every ton of ore processed.By the end of 1982, with 48.2 million tons already mined, the Bell Mine had identified additional mineable reserves of 39.4 million tons containing 0.52% Cu.In November 1979 the Granisle Mine was purchased from Zapata-Granby. The two mines, with a total of 700 employees, were operated under common management as the Babine Division until 1982 when low copper price s forced the closure of both for an indefinite period.The outlook for copper prices remained bleak and only 50 people were retained on the payroll to maintain the two plants, most of them working on a part-time schedule.The population of the Village of Granisle dwindled from over 1500 inhabitants to under 500, as people moved away to seek other employment.Prior to the shutdown, the Bell Mine employed 370 people and pit extraction averaged nearly 50000 tons per day of which 16000 tons was mill feed, and the remainder waste. Total cost to produce a pound of copper was C$1.36 in 1982."

Jan 1, 1990

By David L. Anderson

This paper explores the financial impact of the initial version of the Saskatchewan Potash Reserve Tax; first, a one; and second, in conjunction with the other taxes affecting the industry's profitability. A though the introduction of the Reserve Tax is shown to lead to a substantia increase in a hypothetical firm's effective tax burden, the more unusual outcomes frequently attributed to this levy on y occur after the imposition of other non-provincial tax rulings. Despite this qualification, the results obtained suggest that the Reserve Tax undoubted y acted as a catalyst in the polarization of attitudes during the ear y period of industry/government confrontation

Jan 1, 1979

By Simon Hanner

November 2005 Memorial University Newfoundland and Labrador Mines and Energy Review of Activities Exploration and Mining New Brunswick ?Université du Québec a Montréal McGill University 2005 Manitoba Mining and Minerals Convention Université Laval Quebec Exploration 2005 Saskatchewan Open House December 2005 University of Calgary University of Alberta 'Laurentian University 'Queen's University 'University of Toronto 'Ontario Prospectors Association January 2006 Mineral Exploration Roundup, BC March 2006 Prospectors and Developers Association of Canada Convention April 2006 University of Ottawa Carleton University

May 1, 2006

By H. K. Fredrickson

"Midwest Joint Venture (MJV) owns a high-grade uranium deposit in northern Saskatchewan. The deposit is located too deep below surface to be mined economically by open pit methods, and as a consequence, present plans are that it will be mined by underground methods. High-grade uranium ore of the type at MJV, encased in weak, highly altered ground and with radon-rich water inflows, has not before been mined by underground methods.The test mining phase of the project, completed in 1989, had three objectives: 1. to evaluate radiation protection requirements associated with the handling of large quantities of radon-rich water and mining highgrade uranium ore in an underground environment; 2. to investigate the quantity and quality of water inflows into the mine; and 3. to investigate ground conditions in and around the ore zone as an aid in determining the production mining method to be used.With information gained from the test mining project, a mining method for the production mine has been devised. Level plans have been drawn up, ventilation system designed, pumping arrangements made and methods of ore handling considered. All this is to be done in a manner that will be safe for those doing the work underground. Some of the mining methods planned are felt to be unique in that they are designed to cope with mining problems not known to have been encountered before. New problems underground have required new methods to handle them. Remote drilling, blasting, mucking and backfilling form the basis of the planned mining method."

Jan 1, 1992

By Young C. Kim

A proper economic analysis of pit slope design must reflect the trade-off between the benefits and the increased risk of slope failure inherent in steeper slope angles. However, no formal framework for a proper analysis has existed to date. This paper summarizes the material contained in the Design Chapter Supplement (5-3) of the Pit Slope Manual. The supplement describes the results of the research effort in which a formal economic analysis framework was developed and tested through a case study. The case study results have demonstrated the practicality of the developed procedure and the availability of required data under "real-life" conditions.

Jan 1, 1979

By W. A. D. Edwards

"The Edmonton region accounted for 40% of Alberta's sand and gravel production in 1981 (about 12 million m3). Most of this production was by commercial operations (75%) for use in essential public works projects (64% in road and asphalt production).Although the Alberta Geological Survey delineated 1157 million m3 of gravel, a number of areas are considered to be in short supply. An econometric model was used for forecast demand in the region. Predictions, based on this forecast and estimated supply, are that 15% of the region's gravel and 3% of the sand will be consumed by the year 2010.The City of Edmonton is the largest consumer of aggregate in the region. Approximately 40% of the gravel in Edmonton's current supply area (about 55 km radius) will be used by 2010. These estimates are considered optimistic because the supply figures do not account for sterilization of deposits - some has already taken place in the region. If 25% to 50% of Edmonton's current supplies (one major deposit) were sterilized it would result in $1,000 million of additional cost due to increased haulage alone.Information on the value of aggregate resources, the location of sand and gravel deposit s and forecast demand has been made available to all municipalities in the region to aid planners and regulators in effective future use of this important resource.INTRODUCTIONAlberta is the second largest producer of sand and gravel in Canada at ab out 50 million tonnes annually. Value of provincial production exceeded $120 million in 1985. In Albert a, aggregate is used primarily in road and building construction (about 50% and 15%, respectively) and is important in such activities as petroleum exploration, oil sands development and the forestry industry.The Edmonton region (Fig. I) accounts for about 40% of provincial production and has a per capita consumption rate of about 13.4 m3 of sand and gravel per annum. Although Edmonton dominates, with approximately 50% of regional production going into the city, aggregate is produced in every county and municipal district in the region.Sand and gravel is essential to the current way of life in the Edmonton region. The resource is valuable and dwindling. The Alberta Geological Survey (a department of the Alberta Research Council) has collected information on aggregate in this region for the last decade which ca n aid government planners and regulators in pre venting sterilization and misallocation of this critical resource. This paper is a summary of that information."

Jan 1, 1989

By P. R. A. Andrews, I. Jackman

"A mineral processing investigation to recover chromite was performed at Lakefield Research, under the guidance of CANMET personnel, on a 70 tonne ore sample from the Bird River deposit in Manitoba. In the laboratory phase a flowsheet was developed which involved grinding, gravity separation and flotation. The gravity concentrates were upgraded by magnetic separation and the flotation concentrates by gravity concentration . Pre-concentration by electronic ore sorting, magnetic separation and heavy media separation also was examined.The developed flowsheet was applied on a pilot-plant scale in the second phase of the testwork to the ore as received, and to ore pre-concentrated by electronic ore sorting and magnetic separation. Ore pre-concentrated by heavy-media separation was treated on a laboratory scale based on the pilot-plant flowsheet ,Processing the are as received resulted I n 77% recovery of chromite in a concentrate analyzing 30% Cr20 J; processing are pre-concentrated by electronic are sorting resulted in 64% recovery of chromite in a concentrate analyzing 30.5% Cr20J."

Jan 1, 1988

By L. A. Homeniuk, R. Bonnar

"The Fond-du-Lac uranium deposit is located on the northern rim of the Athabasca Basin. The uranium mineralization is, for the most part, confined to the Athabasca Group, which is underlain by pre-Helikian metamorphic rocks of the Western Craton.The deposit is characterized by a remarkable train of mineralized glacial erratics which led to the original discovery. The mineralization is present as a ""high-grade"" core and a diffuse ""low-grade"" aureole. The ""high-grade"" core occurs as a stockwork of steeply dipping pitchblende veins which strike N 50°E. Hematite, siderite and secondary silicate are also abundant. The ""low-grade"" aureole contains uraniferous goethite, argillaceous material and rare carbon buttons. Recent alteration to coffinite has taken place along the margins of pre-existing ore minerals.The ""high-grade"" core is 390 m long and 10 to 40 m wide, and is surrounded by an irregularly shaped zone of ""low-grade"" mineralization with a similar length and a width of up to 350 m.Comparing the Fond-du-Lac deposit to other unconformity-type deposits, several important differences can be noted:1. Ninety per cent of the ore is above the unconformity, in the Athabasca sandstone.2. The deposit is not associated with underlying graphitic rocks or a major structure.3. The clay-rich alteration zone is not extensive around the Fond-du-Lac deposit.Although there are differences with other Athabasca unconformity-type deposits, the high-grade portion below the unconformity suggests a common origin.The ore deposit is postulated to have been formed from uranium-bearing solutions which entered the stockwork of fractures. Following the reduction in part of these solutions by pre-existing carbonaceous matter and pyrite and/or chemical reaction with pre-existing hematite, deposition continued as a result of decreasing temperature and pressure. Subsequently, minor supergene redistribution of the uranium has taken place."

Jan 1, 1982

By G. E. Agar, W. B. Kipkie, R. A. Tenbergen

"This paper describes the successful pilot plant testing of a flowsheet, developed at Inca Ltd.&apos;s J. Roy Gordon Research Laboratory (JRGRL), for improved separation of the constituent minerals in a bulk copper-nickel concentrate.The flowsheet utilized the fact that xanthate concentration on the mineral surfaces is the most important variable affecting the high lime separation and that reduction of the xanthate concentration could be affected by an oxidative conditioning stage.When the adsorbed xanthate was reduced to a suitably low level, chalcopyrite and pyrrhotite could be floated to leave a high-grade nickel concentrate as the residue. Sodium cyanide was added to the froth product 10 depress pyrrhotite and any remaining pentlandite. The temporary depression of chalcopyrite by the sodium cyanide was overcome by introducing a conditioning step following cyanide addition . The advantages of the flowsheet; improved copper-nickel separation, operation without heating of the pulp, production of both high-grade nickel concentrate (29.5% Ni, .26% Cu) and copper concentrate (<0.5% Ni, 30% Cu) were all realized.IntroductionLaboratory test work undertaken at Inco and described previously(1) has demonstrated the importance of low xanthate concentrations on the mineral surfaces in the copper-nickel separation at the Copper Cliff mill.It was determined that oxidation of the separator feed (a cleaned bulk concentrate, grading about 11% Cu and 11% Ni) to lower the xanthate concentration on the mineral surfaces prior to separation significantly improved the quality of the separation (CI 4)*, particularly when no cyanide is used, but also when cyanide is added. As well, it was found that the oxidation permitted a pentlandite-pyrrhotite separation - the oxidation step brought about a decrease in the flotation-rate of pentlandite leaving pyrrhotite and chalcopyrite largely unaffected. Consequently, it was possible to produce a highgrade pentlandite product (30% Ni, 0.3% Cu) at ~83% Ni recovery , as well as a high-grade copper concentrate (0.5% Ni, 30% Cu at -96% Cu recovery)."

Jan 1, 1985

By M. Ghiani, P. Carbini, R. Ciccu, C. Del Fà

"This paper is concerned with the problems inherent in the efficient and economical processing of the fine fractions of a coal from the Sulcis basin (Sardinia, Italy) whose characteristics are typical of low-rank coals occurring in the Mediterranean region. Three different techniques, based upon surface properties, are examined. Flotation can be very efficient from both a technical and economic point of view, provided care is taken in the modulation of the flotation pulp. Interesting results have been obtained with oil agglomeration and this method could be economically feasible. Finally, electrical separation has proven a viable technique, although it entails preliminary drying.Besides discussing the problems encountered in the experimental research, some significant results of general validity are also given. They demonstrate that cleaned products can be obtained with fairly interesting recoveries, thus opening the way to advanced research aimed at setting up the most suitable technique for industrial application. IntroductionAs a result of the oil crisis, which caused a major upset in world energy supplies, the last ten years have seen a revolution in the energy policies adopted.In particular, the status of coal, which seemed destined to decline in view of the availability of liquid fuel, has had to be re-examined. The need to meet energy demands under improved reliability conditions and controlled prices through a broader and more flexible diversification of sources of supply has evoked, especially in highly industrialized countries, a renewed interest in coal. The result has been a consistent increase in demand and production as well as investments in new mines and the reinforcement of the infrastructure.This turn of events has also lead to a re-evaluation of young low-rank coals, hitherto considered uneconomical and thus neglected, because of their low heat value. In fact these coals, which have a high ash content, may also be relatively highly contaminated with sulphur. The above drawbacks, which still today preclude the widespread use of these coals, are bound to create even greater problems in the future as increasingly restrictive environmental control imposes, without exception, recourse to cleaner fuels."

Jan 1, 1986

By A. McLean, Q. R. Yang, Y. D. Yang, G. F. Zhang, P. Wu

A considerable amount of waste slag from the pyrite roasting process is discharged every year. Recovery of iron from the waste slag is of great interest for comprehensive use of mineral resource, reduction of environment impact and improvement of economical benefit to related companies. The objectives of the present work are focused on: (1) Compare various procedures for recovery of iron from the waste slag and select a best procedure for industrial trial which is roasting of the waste slag under reducing condition followed by magnetic separation; (2) Investigate the optimum conditions for maximum recovery of iron from the waste slag. The experimental result shows that under the treatment condition found in this work about 36 to 40% of the iron oxide was recovered from the waste slag, where the iron content in the concentrate is 57%. The total recovery ratio of iron, up to 70%, from the waste slag was achieved. After the treatment, sulphur content in the waste slag was reduced significantly and gangue materials, such as SiO2, Al2O3 and TiO2, were reduced effectively.

Jan 1, 2011