Search Documents

By W. H. Stheeman

"The high rock pressures at the deeper levels of the Tsumeb Mine have necessitated the changing of the mining methods and the introduction of cable bolts. After two rockfalls in the cable-bolted stopes, the mechanics of cable bolting were investigated. Practical methods were developed to find the best grout mixtures, the bond stresses between cables and cement, the bond stresses between rock and cement and the load on the cable bolts, which was mathematically calculated from data observed underground. The design of the cable bolt support system as used at the Tsumeb Mine is explained. GeneralThe Tsumeb Mine is in northern South West Africa/Namibia, approximately 400 km by road from the capital city, Windhoek, at an elevation of 1300 m above sea level. Mining operations in Tsumeb were started in 1905 by the Otavi Minen und Eisenbahn Gesellschaft and continued, with an interruption during the Depre ssion, until 1940, when the mine was closed and taken over by the Custodian of Enemy Property. The present owner, Tsumeb Corporation Limited, obtained the mine in 1947 and restarted the underground mining operations in 1949 after the mine was dewatered. Currently, the stoping operations are between 26 Level (840 m below surface) and 38 Level (1260 m below surface). In addition, the mine is an important silver producer and has produced 670,100 kg of silver since 1947."

Jan 1, 1982

By W. K. Muwais, R. G. Cuddy

"The Lower Cretaceous McMurray Formation contains the bitumen reserves of the Syncrude Mine in northeastern Alberta. This formation comprises sediments deposited sequentially in fluvial, estuarine and marine depositional environments. The Syncrude Base Mine area consists mostly of estuarine sediments, as much of the original marine sediments have been eroded away. These estuarine deposits consist of channel-fill sediments and interchannel tidal flat sediments with the channel-fills comprising most of the orebody.Channel-fills contain, among other lithologies, interbedded sand, silt and clay rich layers that often occur as sequences of inclined beds with dips up to 25 degrees or more. A detailed knowledge of the distribution of these inclined beds, their lithological characteristics and their continuity is very important in assessing the risk of mine highwall instability . Techniques used to identify and characterize adverse structures are reviewed. INTRODUCTIONGeneralThe Syncrude Canada Ltd. oil sand mine is located within the surface mineable portion of the Athabasca Oil Sands area about 40 kilometres north of Fort McMurray in northeastern Alberta, Canada (Fig. I). The company commenced large-scale strip mining of oil sands in June 1977in the area, referred to as the Base Mine, situated in the southeast corner of the company's two lease areas (Fig. 2).The mining method (Fig. 3) utilizes large electric drag lines operating on a single bench with highwall depths up to 60 metres. Feed grade oil sand (= 6 wt.% bitumen) is mined by draglines and windrowed parallel to the highwall crest. Lower grade oil sand « 6 wt. 0J0 bitumen) occurring as waste bands is selectively mined by the draglines and cast back into the mined out pit or placed on the bench and hauled by truck. The windrowed feed is delivered to the extraction plant by a bucket wheel reclaimer and conveyor system. Stripping of Recent, Pleistocene and Cretaceous overburden units is done outside the conveyor systems by mobile equipment. The 4.5 kilometre long mine is split into four quadrants for planning and scheduling purposes, with each quadrant having an individual dragline-bucketwheel-conveyor system.Surface mining of oil sand at Syncrude requires the removal of vast quantites of material. The design of the open pit mine relies heavily on knowledge of the distribution of ore and waste materials, and on the physical characteristics of these materials.The geology of the oil sand below the dragline bench at the Syncrude Mine is complex. Geological, geotechnical and hydrogeological factors play an important role in the design and operation of the mine. This paper describes aspects of the geology that impact on the design and operation of the mine. Some of the methods and procedures adopted by Syncrude to successfully overcome difficulties that the complex geology creates are discussed."

Jan 1, 1989

By A. Sutherland Brown

"The ProblemMany science activities receive substantial funding from governments without much direct economic benefit accruing to state or individuals. In contrast, the search for knowledge has never been an acceptable so le justification of geoscience activity, perhaps because of its utility right from its inception. William Smith's geological activities were embraced because of their usefulness in building canals. Utility has been expected ever since.For decades it has been accepted at senior level s of government, without much understanding of the process, that geological surveys are necessary as a basis of resource evaluation and utilization. Recently, government treasury board s, staffed with economist s, have questioned these near axioms and in many cases the budget s of geological surveys have reflected their stone y-eyed appraisal s. Are government surveys necessary? Can their functions be reduced? Can some or all of their functions be privatized?Government geologists have been muted in trumpeting their successes outside their own ranks. Companies have been reluctant to give specific public feedback on the work of government surveys that have truly aided or guided them toward discovery. Lack of acknowledged linkages between survey work and discovery has dogged survey managers in budget reviews. Impoverished surveys cannot perform adequately so the circle is completed and the doubters' prophecy fulfilled. This is the genera l problem; British Columbia is the archetypical province."

Jan 1, 1986

By D. M. Hausen

"Refractoriness in Carlin-type gold ores results mostly from fine locking of gold in pyrite, locking in various gangue phases, notably quartz, and a ""preg robbing"" condition attributed to organic carbon. All three conditions may occur in any given deposit, including Newmont &apos;s Carlin and Gold Quarry deposits in Nevada, where types of ref ractoriness occur locally in minor amounts.Measurements of specific gravity, water absorption and screen size distributions of gold in alteration rock types from Gold Quarry show transitional changes from siliceous cherts through decreasingly silicified and increasingly argillized siltstones.Low permeability of siliceous ores contributes to ""size dependent"" refractoriness in cyanidation test work. Colligative physical and chemical measurements demonstrate that silicified cherty ores are difficult to grind, poorly permeable, and less amenable to cyanidation. Refractoriness in pad or column leaching of coarsely crushed siliceous siltstones and cherts is shown to correlate with interrelated measurable mineralogic and physical parameters.IntroductionMetallurgical treatment of variably amenable and refractory types of gold ore may be guided by both analytical and mineralogic data on the interlocking of gold (microscopic an d sub- microscopic) in assorted gangue/sulphide phases. Most oxidized ores from the Carlin gold mine, north of Carlin, Nevada, are amenable to direct cyanidation. The permeability of most oxidized ores from Carlin coupled with the fine size of the gold < 1.5 um) yields rapid extractions and high recovery without fine grinding.Small portions of the Carlin ore body, and also the nearby Maggie Creek and Gold Quarry orebodies, are less amenable to cyanidation, and are classified as refractory. Refractory conditions may be attributed mostly to the association or interlocking of gold with pyrite and /or microcrystalline quartz or chert, and also by the adsorption of leached gold by deleterious forms of carbon, termed ""preg-robbing"" carbon. Each of these conditions are described and defined, with emphasis on a form of silica-locking, which has been referred to as "" size dependent"" refractoriness."

Jan 1, 1985

By D. M. Morrison

"Microseismic systems at five mines in the Sudbury Basin provide the basic data for Falconbridge Limited&apos;s rockburst research. Daily and long-term analysis of this data as well as underground observations has confirmed the fault-slip mechanism of rock bursting at three mines. A detailed analysis of the complete history of Falconbridge Mine is being conducted and Distinct Element numerical models are being used to simulate both the stick-slip behaviour of faults and the dynamic effects of the induced vibrations on rock and backfill. University research includes acoustic tomographic imaging of the rock mass based on seismic wave propagation and collection of full micro seismic waveforms to allow application of advanced seismic and statistical analysis techniques. INTRODUCTIONFalconbridge Limited currently has five mines operating in the Sudbury Basin: East, Lockerby, Onaping, Fraser, and Strathcona Mines, which along with the Falconbridge open pit produced 2.8 million tonnes of ore in 1986. The underground mines range from about 600 m to 2000 m below surface and one of the consequences of mining at these depths is the occurrence of rockbursts.Research into rockburst phenomena at Falconbridge began over 25 years ago and research is continuing in an effort to avoid the problem by improved mine design, to protect mine openings from damage by design of effective support systems and to better understand the processes which precede a major fault slip rockburst. Since the early 1980s, significant progress has been made due principally to micro seismic monitoring and advances in microcomputer technology coupled with detailed underground investigations.It is now possible to identify the fault-slip mechanism as the cause of many of the rockbursts which occur at Falconbridge mines. By gaining an understanding of effect of mining-induced stresses on the pre-existing geological structures, areas which may experience rock bursting can be identified and can be protected against severe damage by appropriate support techniques."

Jan 1, 1989

By Michel Gauthier, Pierre Marcoux, Gaétan Morin

"The recent opening of Muscocho&apos;s gold mine at Montauban, as weil as the discovery of several new copper-gold showings of a similar nature near the confluence of the Saguenay and St , Lawrence has revealed the existence of a new metallogenic gold province which is located within supercrustal units of Helikian age within the Grenville Province. Three metalliferous belts have been identified, each one of which is related to a series of SW-NE trending faults. The first is located in southeastern Ontario and southwestern Quebec. The second extends from the Balmat-Pierrepont mining district of New York State up to the Lac St. Jean region of Quebec, and includes the Montauban camp. The third follows the St. Lawrence river in Charlevoix County and along the north shore of the Gulf of St. Lawrence.The gold mineralization which is present in the central portion of the Grenville Province is of two types: either stratiform or vein. Deposits of the first type, of which the Muscocho is the type locality, are economically the more interesting of the two. Not only is this mineralization stratiform, but also shows a distinct affinity to AI-rich, Mg-rich or calc-silicate-rich bands. As is the case with the Bousquet and Hemlo regions of the Superior Province, they are associated with layers which are rich in sillimanite and occasionally staurolite. A second parallel between the Bousquet and Montauban deposits might be the presence of manganesian gamets, which have been recognized at the two localities. Some of the mineralization in the central Grenville Province is located within thin bands of iron formation which are rich in arsenic.The stratiform gold deposits of the central Grenville Province are of exhalative origin and are located within a volcano-sedimentary terrane. It is probable that a part of the gold present in these Helikian deposits have been derived by remobilization of Archean mineralization. The vein showings form as a consequence of the remobilization of the Helikian strata during the Grenville metamorphism,"

Jan 1, 1985

By M. Fall

The progressive depletion of ore available at shallow depths in several underground mines around the world means that underground mining operations would increasingly be carried out at greater depths and therefore at higher temperatures. However, our understanding of the effect of hot temperatures on the response (mechanical, economical, environmental) of cemented paste backfill (CPB) is still limited. Hence, an extensive laboratory investigation was conducted to study the performance of young and aged CPB, in response to deep mine temperatures. Several CPB samples with different compositions, cured at different temperatures (20 to 50°C) and different times (7 to 160 days) were tested regarding their mechanical properties, economical performance (binder consumption) and microstructural properties. The results show that hot temperatures significantly affect the performance properties of CPB at young and advanced ages. An increase in the curing temperature leads to a considerable improvement of the rate of gain of CPB strength and also to a significant increase of the strength of CPBs studied. CBP samples cured at hot temperatures show lower binder consumption and finer pore structure. Results of this study could serve as background information for the development of optimal mine backfill design procedures.

May 1, 2007

By Bert S. Hall

"IntroductionThe purpose o f this paper is to review the evidence at hand concerning the earliest centuries of cast iron in Europe, from roughly 1400 A.D. until the second half of the sixteenth century. For the most part it is concerned with the relationship between two technologies which emerged first in China and then later appear in Western lands, gunpowder weapons and iron founding. We should not assume, as I hope to show later in this discussion, that weapons constituted the only product for which the iron founder had any market, but it is clearly true that attempts to produce weapons constituted the most severe technical challenge for the early founder. Firearms appear for the first time in Europe in the 1320s and develop into significant weapons on the field of battle by the end of the century. Theirs is a complex history, subject neither to easy summary treatment nor to simplified models of development. I hope to be able, through the analysis of the evidence concerning cast iron, to show that one important strand in the fabric of gunpowder&apos;s history concerns the materials from which cannon could be made. This question is subject to a number of shades of meaning, because ""cannon"" can be made for many purposes under a profusion of different names, and under sharply varying conditions of use. As a result, the question of materials is frequently really a question of competing materials, and involves a complex set of factors, of which production costs and the ultimate safety of the user seem the most important. Judged in this manner cast iron was an important but unsatisfactory metal for weapons purposes until 1543, at which time English founders learned to make iron muzzle-loading cannon which could rival bronze ordinance in most important performance criteria, but which cost much less to produce. With that event, the history of cast iron and the history of weapons entered into the close relationship that persisted until the advent of rifled artillery made of steel in the middle of the nineteenth century."

Jan 1, 1983

By D. H. Rousell

"Rocks of the Whitewater Group (Aphebian age) oc ithin the Sudbury Basin and consist of three formations rre, from oldest to youngest: Onaping, heterolithic breccias lus an igneous-textured component; Onwatin, argillite and siltstone; and Chelmsford, greywacke with minor argillite with siltstone. Mineralization in these rocks is as follows:1) Sulphides are disseminated throughout the Onaping Formation. Pyrrhotite, the major sulphide mineral, occurs mainly as fragments; other sulphides are chalcopyrite, sphalerite, galena, pyrite and marcasite.2) Zn, Pb, Cu, Ag and A u mineralization in the Vermilion member, a carbonate-chert unit near the base of the Onwatin Formation (Vermilion and Errington mines).3) Pyrite and minor base metals in the Onwatin Formation .4) Mineralized quartz veins, located at or near the base of the Onaping Formation, include such deposits as Moore Lake (Pb, Zn and Ag), Foisey (Zn, Pb), Papineau (Cu, Au and Co) and Proulx (Pb, Zn, and Cu). Quartz-carbonate veins in a meta-gabbro sill contain Cu, Zn, As and Au. Material from quartz veins from two former ""gold mines"" (Gordon Lake and Creighton) yielded no Au values.5) Anthraxolite veins in the Onwatin Formation .The mineral occurrences can be explained in term of either the volcanic theory or meteorite-impact theory of basin formation. According to the latter theory, the sulphide fragments in the Onaping Formation may have been formed by the brecciation of sulphide-rich pods located in the upper mantle and at the base of the transient crater; some of the sulphides may have been derived from target rocks of the Huronian Supergroup. The Vermillion-Errington deposits may represent sedimentary exhalative deposits of the Remac type; mineral-rich brines, trapped at the base of the transient crater, rose upward and precipitated the mineralized carbonate-chert under reducing conditions. These conditions continued throughout the deposition of the upper Onwatin Formation but pyrite was the only sulphide that formed.The quartz veins were emplaced during the time of basin deformation. Metamorphism remobilized and concentrated carbonaceous material in the Onwatin Formation 10 form the anthraxolite veins."

Jan 1, 1984

By G. Q. Zhou, H. C. Liang, X. D. Zhao

"This study describes the strain behavior in vertical shaft lining (VSL) embedded in thick soil deposits and its application in assessment of concrete deterioration. The observed strain in VSL continuously decreased companied by a sinusoidal fluctuation due to the influences derived from negative skin friction (NSF) and temperature. The increase in strain increment between peak and trough at each year and compressive strain level as the servicing time continued and VSL depth increased implies that the concrete strength was attenuated, and this attenuation was significantly dependent on the existing compressive strain level in VSL. The reliability of the proposed approach was validated by Schmidt Hammer Technique (SHT) – based concrete strength, and is applicable in concrete assessment and then fracturing prediction of VLSs in thick soil deposits.Concrete strength, Field monitoring, Strain behavior, Vertical shaft liningINTRODUCTIONOver 100 VSLs in Southeastern China subjected to an unpredictable fracturing as shown in Figure1, and there are over 1,000 VSLs embedded in thick alluvium su?ering from challenges of damaging and potential fracturing (Cheng, Yang, Zhou, Li, & Hu, 1993; Zhou, Cui, Lv, Huang, & Chen, 1999; Li & Li,2005). Therefore, a reliable assessment of these VSLs is significant to the normal servicing of mine shafts and the recycle of underground space when these mine shafts were closed.The continuous increasing of NSF induced by the drainage of water–saturated deposits well interpreted such extensive fracturing phenomenon, and it is universally regarded as the governing indicator to determine the VSL stabilization (Cheng et al., 1993; Zhou et al., 1999). Based on this recognition, the fracturing prediction and VSL strengthening according to the field monitoring on hydrogeological characteristics, servicing environments, and mechanical behaviors of VSL were carried out (Zhao, Zhou, Zhong, Zhu, & Liang, 2009; Liang et al., 2009; Xie, Lv, & Wu, 2014). As known, the compressive strain level in VSL and the in–situ strength of VSL concrete were the main factors to perform such fracturing prediction. However, the existing studies in literatures were limited to the strain accumulating or releasing behaviors (Zhao, Zhou, Zhao, Kuang, & Hu, 2017), and lack of considering the VSL concrete strength and its attenuation. In this reported study, the in–situ monitoring data on the strain in typical VSLs and the VSL elevations between 2004 and 2014 were initially analyzed. Then, an observed strain behaviors–based approach was developed to quantitatively evaluate the VSL concrete deterioration."

Jan 1, 2019

By C. Tong, B. Hilscher

"Sensor based ore sorting is being rapidly adopted by the mining industry. The ability to boost mill feed grade by rejecting waste grade rocks early in the process has proven revolutionary for some operations.This paper briefly reviews the current position of ore sorting in the industry, as well as abridged results from specific operations such as Barrick, McEwen, New Gold, and two others. The paper also introduces the concept of “Profit Recovery™”, the measuring of recovery based on rock profitability rather than just metal content.IntroductionSensor based ore sorting is being rapidly adopted by the mining industry. The ability to increase mill feed grade by rejecting waste grade rocks early in the processing stage is proving to be revolutionary for some operations. These potential outcomes have been too invaluable to be overlooked by both producing operations and prospective projects, thus leading to a wide range of studies on ore sorting. In addition, the advent of ore sorting has also called for a new standard of recovery analysis. The answer to this is the creation of a new term and concept - Profit Recovery™.This paper evaluates the most recent results of ore sorting in the mining industry, and presents the results from five different mining operations. Additionally, this paper will discuss and evaluate the Profit Recovery™ of each of these operations. The goal of this paper is to address common concerns regarding ore sorting rejects and their actual impact on project economics.State Of The ArtOre Sorting is a sensor-based sorting and pre-concentration technology implemented before the processing stage that is used to reduce the amount of waste reporting to the mill feed. This technology can also be utilized to recover ore from previously uneconomic waste, as well as reduce the mill energy and reagent consumption (Tong, 2012). In greenfield projects, sensor-based sorting can further provide value by reducing processing capital costs. The decline of available high grade orebodies and decreasing head grades has further increased the attractiveness of pre-concentration, and subsequently ore sorting (Lessard et al., 2014).There are currently two notable types of sensor-based sorting: bulk and rock-by-rock. Bulk sorting consists of live, high tonnage sorting that can be installed on a scoop or on a conveyor belt with a diverter. Rock-by-rock is a selective sorting method that scans and sorts individual rocks on a conveyor belt, and rejects rocks using air jets or mechanical levers. Figure 1 shows a diagram for a typical air jet sorter."

Jan 1, 2018

Resistance spot welding is the most common type of welding in the automotive industry. In RSW the size and shape of welding nugget is one of the most effective factors on mechanical properties, such as tensile shear strength and fatigue strength. so properly adjusting the variables of the welding is necessary .in this study the effect of different parameters of RSW including time, current, electrode force, geometry of electrode so diameter and angle of electrode tip in the shape and size of welding nugget evaluated. for experimental procedure, low carbon steel sheet st12 is used. the process is simulated with finite element method by using ANSYS software. for the formation of welding nugget a 2 dimensional symmetrical model electrical-thermalmechanical is used and for elevate the accuracy ,we determined the properties of material related to temperature. The results show that increasing the time and current of welding, the diameter of spot weld also increased and the role of current is more impressive. and also increasing the electrode force decrease the diameter of the nugget due to increasing the contact area and decreasing the resistance .increasing the diameter of electrode tip cause increasing contact area and decreasing the resistance and decreasing the diameter of the nugget. furthermore, changing tip angle and electrode diameter don&apos;t show sensible change in the geometry of the welding nugget. comparison between simulation and experimental result show a good adaption.

Oct 1, 2011

By EJ. Reichhardf

The Molopo Farms Complex is a major, layered ultramafic/mafic, early Proterowic intrusion which is totally covered by sediments of the Karoo and Kalahari Fonnations and situated in southern Botswana and northeastern South Africa. The approximately 3000 m thick, generally fine- to medium-grained ultramafic and mafic cumulates are intrusive into equivalents of Thmsvaal Supergroup sediments and lavas. Multiphase defonnation resulted in tilting and segmentation of the Complex into individual tectonic blocks. Sr isotopes document at least two chemically distinct parental liquids which interacted in a complex manner to form an approximately 1000 m thick rhythmically layered succession which straddles the ultramafic/mafic boundary. Repeated mixing resulted in a complex cryptic layering pattern and numerous sulfide-enriched layers which contain significant PGE+Au concentrations.

Jan 1, 1994

By Mahmoud Shakeri1

Various types of thin-walled structures have been frequently used as energy absorbers to mitigate the adverse effects of impact and hence protect the vehicle structure under consideration when subjected to different loading conditions. Compression tubular structures that buckle in a progressive manner, can be used to advantage, providing inexpensive and versatile, but nevertheless weight and stroke efficient energy absorbers. In this paper quasi-static nonlinear finite element simulations are performed to study the effects of number of corners of the cross-section, wall thickness, plastic hardening rate of material, foam-filler and load angle on deformation mode and mean crushing force of tube. Crush strength increases as the number of corners of the cross-section increases, though it almost saturates for the number of corners beyond 11. Higher plastic hardening rate stabilizes the collapse pattern. Foam-filled tubes seem to have higher critical load angles in oblique loading and display a more stable and gradual decrease in mean load over the transition region. Substantial decrease in the initial peak load and dynamic load at any a given deflection was observed as the load angle increases. The investigation of bitubal arrangements and Multi-cell tubes reveals that these may be preferable to monotubal specimens due to the presence of the inner profiles. In addition, a comparison is conducted between the numerical and experimental results of the mean forces of some special angle elements. Good agreement is obtained.

Oct 1, 2011

By Robert B. Parsons

"Canada doesn&apos;t really have a tax system for mining - it has eleven separate tax systems! The consequent maze adds some undefinable margin of difficulty to making investment decisions in Canada. But, this 11U1Ze is not likely to be simplified. Solution: learn it and sell it! Intricate Network of Winding PathwaysWebster&apos;s New World Dictionary defines the word ""maze"" as follows: ""a confusing, intricate network of winding pathways; labyrinth ... a state of confusion or bewilderment"". Webster&apos;s does not go on to give an example of a maze, but the dictionary could easily have referred to the taxation of a Canadian mining operation. The uninitiated would almost certainly look upon such taxation as a maze of the most perplexing sort.Twenty years ago, Canada&apos;s tax system was really quite simple. It is true that Canadian mining profits were subject to three levels of taxation (federal income tax, provincial income tax, and provincial mining tax), but this didn&apos;t pose a problem. Prior to 1974, at least the provincial income tax systems were somewhat the same in terms of rules .and rates, and even the provincial mining tax systems resembled one another. Mining profits were subject to pretty much the same rules, no matter what province or territory hosted the mine. Those were the “good old days” one could even dare to generalize about tax rates without fear of being labelled an imbecile!"

Jan 1, 1994

By Guy Chevalier

QCM?s pellet plant, located in Port-Cartier, Quebec, produces up to 8.6 million tons of iron ore pellets annually. Four different types are produced: three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the installation of new process equipment to improve the reducibility of direct reduction pellets (DR pellet). The findings, the equipment selection and some post start-up modifications are presented. This low silica DR pellet is used in Midrex and HyL shaft furnaces. A good DR pellet has to meet strict chemical, physical and metallurgical specifications. An important metallurgical property is its ability to release oxygen when exposed to reducing gases. Considering that the market for DR pellets is expanding and being aware that reducibility is critical for our clients, a program to improve the latter was undertaken. Test work showed that one factor which has a negative effect on reducibility is the proportion of particles larger than 75 microns. Knowing that the best way to reduce the amount of coarse particles was to close our open grinding circuits, we began evaluating the most suitable classification equipment applicable to our process operations. We settled on hydro-classifiers based on their very sharp cut and their low operating costs. In light of the hydro-classifiers performance it was also decided to replace the hydro-cyclones of an already closed circuit.

May 1, 2003

By T. R. Carter, A. C. Colvine

"Rocks of the Grenville Province in southeastern Ontario are currently largely dismissed by many geologists as having little or no potential for discovery of significant deposits of metallic minerals. The present study demonstrates that the area contains numerous deposit types which elsewhere are major metal producers. Therefore, there is significant unrealized potential, especially for gold, zinc, uranium, and possibly copper.The variety of deposits of metallic mineralization include stratiform zinc in marbles; stratabound base metal sulphides in volcanic and sedimentary hosts; gold-quartz veins; quartzmagnetite iron formation; copper-nickel and iron-titanium in intrusive rocks; magnetite skarns; molybdenum in skarns and pegmatites; uranium and thorium in pegmatites, veins, and calc-silicate gneisses; hematite veins; dolomite marbles (magnesium); and barite-jluorite-celestite-galena-calcite veins. There has been significant production of iron, lead, zinc, magnesium, gold, silver, and uranium.The vast majority of the metallic mineral deposits are confined to late Precambrian supracrustal and related intrusive rocks of the Grenville Supergroup. Many of the deposits are stratiform and/or stratabound and occur within units toward the top of major volcanic successions and in the lower portions of younger carbonate-clastic sedimentary successions.Processes responsible for mineral concentration in the area include: (I) syngenetic hydrothermal activity related to both volcanism and sedimentation; (2) epigenetic processes related to diagenesis, regional metamorphism, and igneous intrusive activity; (3) magmatic processes related to igneous intrusions; and (4) supergene concentration and enrichment. The genetic classification of the mineral deposits presented is based on observed geological relationships and these interpreted geneses. The deposit types have counterparts in volcanogenic and sedimentary exhalative, Mississippi Valley type, magmatic, contact metasomatic, and lode gold deposits. Many of the exploration criteria for deposits of these types may be applicable in the Grenville Province, despite the generally high metamorphic grades and complex deformation."

Jan 1, 1985

By James F. Allan

"The Kipawa yttrium-zirconium prospect is located about 150 km south of Noranda, Quebec. Yttrium-zirconium mineralization occurs in an elongate, regionally metamorphosed and deformed peralkaline complex in the Grenville terrain. The mineralized zone, as defined by =.0.10% Y2O3, is 1300 m long and 10 m to 30 m wide. Zirconium content typically ranges from 0.50 to 1.20% ZrO2, The mineralized zone strikes northwest and dips 20 degrees to 35 degrees to the southwest. It occurs at the structural base of the peralkaline complex in syenite gneiss and calc-silicate rocks and is conformable with both the footwall contact of the complex, and the layering and gneissosity in the enclosing rocks. Minerals of economic interest are eudialyte (sodium-zirconium silicate), mosandrite (sodium-titanium silicate), britholite (calcium-silica phosphate), and a few other uncommon zirconium and titanium silicate minerals.The highest and most continuous yttrium grades occur in the upper part of the syenite gneiss unit in areas containing eudialyte, mosandrite and minor britholite. Yttrium also occurs in britholite in calc-silicate rocks and in mosandrite in syenitic rocks in the lower part of the syenite gneiss unit. Both the yttrium-bearing minerals and yttrium grades are erratic in the lower part of the unit. Zirconium is generally more uniformly distributed than yttrium. A peralkaline granite gneiss phase of the complex intrudes the syenite gneiss and possibly truncates it, and the mineralization, near the southern boundary of the mineralized zone.The mineralized zone is coincident with a radiometric anomaly and discontinuous yttrium and zirconium soil anomalies.More drilling and metallurgical studies will be required to determine the economic viability of the yttrium and zirconium mineralization at Kipawa."

Jan 1, 1992

By James F. Allan

"The Kipawa yttrium-zirconium prospect is located about 150 km south of Noranda, Quebec. Yttrium-zirconium mineralization occurs in an elongate, regionally metamorphosed and deformed peralkaline complex in the Grenville terrain. The mineralized zone, as defined by =.0.10% Y2O3, is 1300 m long and 10 m to 30 m wide. Zirconium content typically ranges from 0.50 to 1.20% ZrO2, The mineralized zone strikes northwest and dips 20 degrees to 35 degrees to the southwest. It occurs at the structural base of the peralkaline complex in syenite gneiss and calc-silicate rocks and is conformable with both the footwall contact of the complex, and the layering and gneissosity in the enclosing rocks. Minerals of economic interest are eudialyte (sodium-zirconium silicate), mosandrite (sodium-titanium silicate), britholite (calcium-silica phosphate), and a few other uncommon zirconium and titanium silicate minerals.The highest and most continuous yttrium grades occur in the upper part of the syenite gneiss unit in areas containing eudialyte, mosandrite and minor britholite. Yttrium also occurs in britholite in calc-silicate rocks and in mosandrite in syenitic rocks in the lower part of the syenite gneiss unit. Both the yttrium-bearing minerals and yttrium grades are erratic in the lower part of the unit. Zirconium is generally more uniformly distributed than yttrium. A peralkaline granite gneiss phase of the complex intrudes the syenite gneiss and possibly truncates it, and the mineralization, near the southern boundary of the mineralized zone.The mineralized zone is coincident with a radiometric anomaly and discontinuous yttrium and zirconium soil anomalies.More drilling and metallurgical studies will be required to determine the economic viability of the yttrium and zirconium mineralization at Kipawa."

Jan 1, 1992

By E. Laatio, W. McKay

"History of Tara Mines Ltd.Tara Exploration and Development Company Ltd. was formed in Canada by Irishmen in 1953. The discovery of an orebody approximately six miles from the historically famous Hill of Tara in County Meath was a wild dream . Nevertheless this dream became a reality. Tara Mines Ltd. was formed, and the mine developed some 35 miles northwest of the City of Dublin in the Irish Republic.Tara&apos;s original drilling program indicated a zinc-lead orebody of approximately 60 million tonnes grading at 10.1% Zn and 2.6% Pb. The terms of the mining lease stipulated that the Irish government would acquire 25% equity interest in the operation. The mine was thus owned 75% by Tara Exploration and Development Company Ltd. of which the principal shareholders were Noranda and Northgate, together with 25% being held by the Irish government. The mine was purchased in March 1986 by Outokumpu Oy, a Finnish mining and metallurgical company, and together with the 25% government stake are the current owners. Outokumpu Analysis on Tara Mines Ltd.Upon ownership Outokumpu carried out a comprehensive analysis on the operation and came to the following conclusions :1. Tara had a good orebody;2. Tara had a skilled, capable, stable workforce;3. Tara&apos;s concentrator and processing equipment was adequate to meet requirements;4. Tara&apos;s mobile equipment fleet was too old and too numerousin numbers; and5. Tara had too many employees, both staff and hourly paid .With ore reserves of approximately 50 million tonnes and at a planned extraction rate of 2.6 million tonnes it meant that the mine had a lifespan of approximately 20 years. To be a viable operation into the future, the mine had to become more efficient. Operating costs and manpower levels had to be dramatically reduced."

Jan 1, 1989