Search Documents

By William C. Martin

"Consolidated Sudbury Basin Mines Limited owns two mines, 4 miles apart, near the southwest end of Sudbury Basin. The Errington mine lies close to the north boundary of Creighton Township and about 18 miles by car from Sudbury. The Vermilion Lake mine is in Fairbank Township, on the south side of Vermilion Lake.The first discovery of base-metal mineralization within Sudbury basin was made by James Stobie in 1897 at Stobie Falls on the Vermilion River, half a mile west of the Errington mine. A few years later Alphonse Oilier made a discovery of massive pyrite with base-metal sulphides near the west end of the present Errington workings.No work of consequence was done on these discoveries until 1924, when Joseph Errington acquired options on a large acreage of ground which was later taken over by the Treadwell Yukon Company Limited. After considerable diamond drilling this company sank No. 1 shaft in 1926. In the next three years, a large amount of underground development was done, a pilot mill was constructed and operated for two years. All operations ceased in 1931 with the fall in metal prices. While in operation the pilot mill treated 186,172 tons of ore the average grade of which was 1·07 per cent copper; 1 10 per cent lead; 4·60 per cent zinc; 0·03 ounces gold; and 1 70 ounces silver.Up to the time of closing in 193 l there had been completed at the mine 26, 790 feet of lateral work and 75,500 feet of surface and underground diamond drilling. The company records, however, showed no figures on ore reserves, except broken ore in stopes amounting to about 60,000 tons. A study of the plans, prior to reopening the mine in 1952, showed 1,450 lineal feet of ore (at 1952 prices) opened up by drifting on the 300-foot and 500- foot levels. It is clear that no comprehensive picture of the structure was had at this time. The orebodies were considered to be very irregular pods scattered through masses of quartzite-carbonate in a sheared zone about 800 feet wide. In some way the ore was believed to be related to the tuff-slate contact zone. With this picture it was impossible to make a reasonable ore estimate or even gauge the tonnage potentialities with any feeling of reliability."

Jan 1, 1949

By Fred A. Webber

STEEL ROPE WIRE is one of the more specialized commodities among the many grades of highcarbon steel wires. In its production there are many metallurgical aspects of interest from the steelmaking on through the final stages of wire drawing. We produce rope wire in an integrated mill com prising all the operations from the blast furnaces to finished wire drawing in the wire mills. Steelmaking is carried out with close control on hot metal, selection of scrap, and fluxing materials. The basic open hearths are of 170 tons capacity. Steel is teemed into 19 1/2 in by 19 1/2 in big-end-down molds and is hot-topped with the use of clay refractory hot-tops. The weight of this ingot is 6,900 pounds. All high -carbon steel ingots are charged hot into the soaking pits and are then rolled through the blooming mill in 16 p asses to a bloom ax~ in. by 41/2 in. and approximately 65 feet long. Necessary bottom and top crops are taken on the bloom as it passes from the blooming? mill to the billet mill. The still hot bloom is continuously rolled through the billet mill in . 5 passes to a 2 3/8 in. square. Billets are cut to 32 feet in length by a flying shear and then allowed to cool on the hot bed.

Jan 1, 1957

Cansolv® S02 Scrubbing Technology was described in a paper in Copper/Cobre 03. Four years on, the technology is operating at a full scale production facility.Hindustan Zinc Limited expanded their capacity by installing the AUSMELT process. The process proceeds through smelting, slag reduction, slag cleaning and holding stages sequentially in the same vessel, resulting in widely varying off gas characteristics. The off gas is suitable for treatment is a conventional acid plant for a modest proportion of the day, but at other times produces off gas too high in S02 to be discharged to atmosphere. Cansolv® S02 Scrubbing Technology was identified as a means of effectively removing the S02 down to low levels from the off gas during all stages of the pyrometallurgical process. Furthermore, the Cansolv® S02 Scrubbing System Technology produces high purity S02 that allowed for the captured S02 to be directed to an existing acid plant, avoiding the capital cost of new acid making capacity.

Jan 1, 2007

By Howard W. Tipper, Richard B. Campbell

"The Quesnel Trough is underlain by a thick sequence of mainly Upper Triassic and Lower Jurassic volcanic-clastic and sedimentary rocks that lie between the highly deformed Proterozoic and Paleozoic rocks in the Omineca Geanticline to the east and the Upper Paleozoic Cache Creek Group in the Pinchi Geanticline to the west. Broad areas of the Trough between Kamloops and Williams Lake are covered by Eocene volcanics and sediments and by Miocene-Pliocene plateau lava. Granitic intrusions were apparently mainly confined to two major episodes; one about 200 m.y. ago (coeval with the Guichon batholith) and one about 100 m.y. ago. In addition, the region includes small granitic and syenitic intrusions, some porphyritic, that may be all or partly still younger. Exposures in the region are generally small and scattered, obscured by widespread, not necessarily thick glacial deposits. This, together with the extensive Tertiary cover, makes prospecting difficult. The part of the Quesnel Trough discussed here is the direct northwest-ward extension of the copper-rich Kamloops-Merritt-Princeton region. It contains the Boss Mountain molybdenum mine, related to a breccia zone induced in a batholith of the oldest group by a younger intrusion, and the Cariboo Bell copper deposit in Lower Jurassic volcanic-elastic rocks and syenitic intrusions. The Gibraltar deposit, in a 200-m.y. intrusion, is within the Pinchi Geanticline close to the margin of the Trough. Molybdenum prospects are mainly restricted within or near the 100-m.y. granitic rocks. Copper prospects, on the other hand, are most prominent in the volcanic-elastic rocks and in the 200-m.y.-old granitic rocks, although they can also be spatially related to younger intrusions. Copper thus has a wide potential distribution.The writers believe that the region is deserving of careful and comprehensive exploration by directly applying the knowledge and techniques developed in the important producing areas to the south. All of the major pre-Tertiary geological elements seem to have potential for mineral deposits; none should be ignored. A thorough knowledge of the thickness and distribution of the Tertiary rocks and the development of geophysical methods to ""see through"" them is of particular importance."

Jan 1, 1970

By Chris Brothen

The introduction of new technology in mine operations has provided real opportunities for increased efficiencies and production gains which translate into enhanced profits. Computing and network technology usage has become integrated into surface mining operations and on average these investments in technology have proven beneficial for efficiency and productivity improvements. Embracing new technologies however, does not guarantee positive results. The expectations or improvements derived through the technology must be confirmed and clarified well before implementation. Tire Pressure and Temperature Monitoring Systems are an excellent example of an existing technology that can provide full time automated performance measurements of tires operating under harsh conditions and environments. Prompt warnings or alarms signaling when a tire has exceeded operating capacities will provide savings through lowered maintenance costs and increased productivity. To truly quantify the projected savings in tire life, fuel consumption, and increased levels of production, all costs associated with the technology, both direct and indirect must be considered. Apart from the initial cost of the system implementation, ongoing maintenance and support costs must be considered as well as the costs of system integration into existing mine operations

May 1, 2008

By G. Girard, A. Larouche, J. Colbert, G. Doyer

"The Direct Chill (DC) casting process uses water to extract heat from molten aluminium and helps to control the solidification process. Many factors such as the water flowrate, water distribution around the mould and water impingement angle have significant impacts on the solidification process. It has been noted that the chemistry variation of the cooling water is also an important factor that has a major impact on the presence of defects on the ingot. A significant change in the water quality can produce defects on the ingots such as cracks, bleedouts, or runouts. Understanding the impact of water quality variation on ingots is therefore essential to ensure good ingot production and reduce defects. This paper aims at describing a new approach to follow the variations of process water quality over time. It is an original and innovative method, which is still under progress. A water quality and stability index (WQSI) is under development to evaluate changes in the water composition based on water physico-chemical parameters. The index is calculated by comparing each of the actual parameters with historical values previously modeled by a statistical law. It is a dimensionless number having an adjustable weight factor for each parameter. The positive or negative contribution of each parameter, with respect to the water cooling capacity, is taken into account to calculate the WQSI. The current selection of parameters is based on knowledge from the literature as well as on empirical experience. When the developed tool will be mature, it could be used to track water variations upon time and anticipate problems, enabling proactive actions to ensure good ingot production.INTRODUCTIONFor many years, the impact of water chemistry on heat transfer, during DC casting, has been of great interest in the aluminum industry. Several papers have been published to demonstrate the correlation between water chemistry and heat transfer (Yu, 1985), (Gildemeister, 2014). Although numerous studies do present the effects of water parameters (i. e. hardness, conductivity, oil, and grease…) on cooling capacity under controlled experimental conditions, they do not reflect the strong interactions between the parameters and variations present in a casting center. Wells and Cockcroft also demonstrated that laboratory based studies are not fully representative of real heat transfer in an industrial casthouse, there are too many factors involved (Wells, Li, & Cockcroft, 2001). In this context, it becomes very difficult to obtain a quantifiable relationship between the capacity of water to cool the ingot and ultimately the performance of the cast."

Jan 1, 2016

By F. J. Macias, A. Bruland, F. E. Dahl

"Tunnelling by use of Tunnel Boring Machine (TBM) is gaining a greater presence as a suitable excavation method. Disc cutter consumption has a strong influence on performance and cost when using TBMs and the influence becomes even more relevant in hard rock. Furthermore, good predictions of TBM performance and cost facilitate the control of risk as well as avoiding delays and budget overruns. Since abrasive wear is the most common process affecting cutter consumption, good laboratory assessments are needed. A new abrasivity test method called Rolling Indentation Abrasion Test was developed. The goal of the new test design and procedure is to reproduce wear behaviour on hard rock tunnel boring in a more realistic way than traditionally used methods by introducing wear by rolling contact on intact rock samples. INTRODUCTIONHigh investments are involved in the tunnelling industry, especially in Tunnel Boring Machines (TBMs) projects. Performance predictions and cost estimations are crucial for planning and risk management of TBM projects. Cutter consumption has a large influence in terms of time and cost, and an even greater effect in case of hard rock projects. Many factors are influencing the amount of cutters consumed in hard rock TBMs. Normal TBM operation results mainly in abrasive wear on the cutters and appropriate methods for abrasivity assessment are needed. Rock abrasiveness cannot be considered as an intrinsic property and the complete tribological system should be considered in addition to the geological properties of the rock.In the present paper, a new test method for abrasivity assessment in tunnel boring called Rolling Indentation Abrasion Test (RIAT) is presented. The traditionally used test methods for determination of rock abrasiveness uses sliding or impact contact in order to cause wear while the RIAT introduces rolling contact on intact rock samples. The ambition of the new test device is to have a reliable method to evaluate the cutter wear in hard rock tunnel boring by reproducing wear behaviour on rolling disc cutters in a more realistic way. It has been established by many authors that the abrasion of a cutter ring is proportional to its rolling distance (Rostami, 1997; Bruland, 1998). In the present work, the weight loss of a mini-cutter ring is measured subsequent to testing in order to evaluate wear in the rolling process and could hence be related to cutter ring wear. Indentation of the tools in the intact rock sample is considered as an indication of the surface hardness of the rock or the resistance to indentation by rolling."

Jan 1, 2015

By C. Blawert

The corrosion properties of the skin and the bulk of semi-solid processed and high pressure die cast AZ91 alloy were studied in 5% NaCI solution by (a) analysing the corrosion morphology, (b) measuring electrochemical polarization curves, (c) performing electrochemical impedance spectroscopic measurements, and (d) immersion tests at constant pH-values. Using XRD, LM, SEM and EDX to evaluate the microstructure of skin and bulk specimens, the corrosion results were related to the microstructures of the particular alloys. However, microstructure and corrosion performance were found to be similar for both production processes, and only slight but distinct differences were found. Generally, the skin corrosion properties are inferior to those of the bulk, with the exception of the high pressure die cast AZ91 alloy, where the finer microstructure of the skin layer exhibits a better performance as showed by impedance studies and confirmed in long term immersion tests.

Jan 1, 2004

?Podolsky Water treatment plant discharges to Norman North bog which drains into Whistle / Post Creek watershed and into Wanapitei Lake ?Whistle Mine closed and reclaimed but continues to treat and discharge water to Whistle Creek

May 1, 2009

By S. Banisi, M. Maleki-Moghaddam

Direct observation of charge shape and its motion in industrial mills is not possible; therefore, a combination of analytical and physical studies is used to determine charge trajectory. Software packages, which predict charge motion consider only the outermost layer of charge (single ball) and ignore the charge and the interactions of grinding elements. In the new version of the GMT (Grinding Media Trajectory) software, the effect of liners specification and bulk load on charge shape and trajectory are considered. The charge trajectory was measured in a laboratory mill with the diameter of 100 cm and length of 21.5 cm with the transparent end and compared with that of the old version of GMT. Four types of polyurethane rings were accurately machined to scale down the liners arrangements at two industrial mills. The model mill was operated at 55, 70 and 85% of the critical speed for five levels of mill filling (10, 15, 20, 25% and 30% by volume). The experiments indicated that the end walls effect was negligible for the model mill with the length of 10.8 cm and beyond. The proposed relationships to correct the trajectory and charge shape were validated by using the new liner of the Gol-E-Gohar iron ore company AG mill. The positions of shoulder, toe, toe departure and impact points were predicted with the relative errors of 5, 0.7, 2 and 0.2%, respectively. The GMT software was updated with the new relationships. The results of GMT simulation indicated that when the lifter face angle increased from 7 to 30°, the distance between the charge impact point and the toe decreased from 40.1 to 11.2° for 30% filling. The change in the position of the impact point meant increasing the probability of charge impacting the toe, not the liner which favored more efficient comminution practice.

Jan 1, 2016

By I. M. Gordon, J. Blackshaw

"Run-of-mine ore is reduced to 4 per cent on 4 mesh (3/ 16 inch), using four stages of dry crushing. The mill feed is then reduced to 2 per cent on 48 mesh and 60 per cent through 200 mesh, using one stage of ball milling in cyanide solution. During the subsequent treatment about one-tenth of the tonnage is removed as a table concentrate and ground to 77 per cent through 325 mesh. The size of the mill tailing is 66 per cent through 200 mesh.Four stages of ore reduction began when the dry crushing plant at No. 26 Shaft came into operation at a maximum rate of 440 tons an hour on July 31, 1941. A detailed description of the crushing plant was published in C .I .M. Trans., Vol. LVI, 1953.One-stage ball milling in cyanide solution came into full operation on January 11, 1938. The ball milling plant had a capacity of 4800 tons daily when reducing mill feed at 2. 7 per cent on 1/ 4 inch to 54. 3 per cent through 200 mesh. Primary grinding to 60 per cent through 200 mesh commenced May 22, 1945, when the feed was 3 per cent on 4 mesh. Under these conditions the capacity of the ball milling plant is estimated at 4300 tons daily. A description of the 11 Hollinger Crushing and Grinding Plant"" by D. C. McLaren was published in the Canadian Mining Journal, June 1944.The concentrate grinding circuit using a 7 x 15 low discharge ball mill and a 19-foot diameter bowl classifier with a 6-inch centrifugal pump to close the circuit began operating in the ball milling plant on October 24, 1939."

Jan 1, 1965

The dynamic breakage process of rocks by the impact of a hydraulic hammer is more complex than one normally assumes. It is even more difficult when one has to conduct the breakage under water. In such cases one does not know exactly what the surface topography and composition are at the bottom of the sea or river and, hence, it is more difficult to select the best position of the hammer before starting the hammering. Typically, an industrial hammer has a diameter of about 250 mm, a length of about 1.25 to 1.75 m and a mass of several tons. The hammer frequency can be up to 50 impacts per minute. The general principles of rock hammering can be easily summarized, but this knowledge is not sufficient to adapt adequately the method for less common rock conditions (e.g. less brittle rock, presence of vertical and subvertical fractures, etc.). That is the reason why we initiated a research project, whereby a scale model has been developed to conduct experiments in the laboratory and whereby discrete element simulations are being conducted. Both aim at a better understanding of the basic mechanisms of rock hammering. The scaled experimental model allows varying the impact energy and the static weight independently. Within the experiment, the hammer is in contact with the rock specimen under a certain confining pressure and with a certain contact pressure due to the static weight. A weight falls on the hammer, creating the dynamic action or impact; the height over which the weight falls can be varied. The penetration is recorded after each impact. After a certain penetration the test is stopped and the internal crack patterns are described. Some simulations have been conducted, allowing the modeling of individual fracture initiation and growth during the penetration of the hammer by either a constant displacement rate (using the UDEC-code) or by introducing the dynamic process (using the PFC-code). Some of the observed features in the laboratory experiments can be visualized in the simulations. However, further research is needed to allow the simulations being an adequate tool to well understand the dynamic process in laboratory experiments, as well as the in-situ behavior.

Aug 1, 2013

By R. Saulters, M. Garshasb

The Transportable Moisture Limit (TML) is the copper concentrate moisture content beyond which liquefaction may occur during shipping. This study indicates that TML is a function of mineralogical characteristics of concentrate, which in turn may directly affect moisture retention properties. A comprehensive mineralogical and chemical analysis was conducted to determine the impact of composition and mineral content on concentrate’s TML. The analysis indicates that the high TML value is associated with particular minerals such as gypsum, swelling clay, muscovite and pyrite. Since higher TML values allow higher moisture contents for shipping, this property is desirable for concentrate inventory management and shipping flexibility. Scarcity of minerals that may increase TML contributes to limitations of shippable inventory. INTRODUCTION TML is the maximum moisture content of copper concentrate beyond which liquefaction may occur. Moisture content above the TML is considered a shipping hazard as it may result in loss of lives and cargo. The details of TML testing are given in ISO 12742:2007 (ISO 12742). In principle, TML is 90% of the Flow Moisture Point. The method of testing for Flow Moisture Point and TML is based on procedures that provide pulsations that simulate the cyclic force of ocean waves to determine moisture levels at which the onset of concentrate flow may occur. International Maritime Organization (IMO) provides guidelines for developing and approving TML testing and moisture determination in the context of its Moisture Management Plan (MMP) for shipment of copper concentrate cargoes (IMO 2013). The IMO regulations are specifically provided in MSC.1/Circ. 1454 “Guidelines for developing and approving procedures for sampling, testing and controlling the moisture content for solid bulk cargoes which may liquefy”. Since each port has its own operational characteristics, resource availability, peculiarities of governmental structure, and desired methods of interaction with the authorities, it is necessary to adopt the IMO guidelines to the local requirements. In order to establish a TML and MMP measurement system, it is required to implement and follow proper guidelines for the relevant procedures. For example, sampling procedures are developed in accordance of ISO 12743, “Copper, lead, zinc, and nickel concentrates – Sampling procedures for determination of metal and moisture content”. Moisture content of copper concentrate samples are determined in accordance with ISO 10251, “Copper, lead, zinc, and nickel concentrates – Determination of mass loss of bulk material on drying”. To assure strict adherence to the MMP procedures, the overall system needs to be integrated into the site QA/QC system, which would make them auditable and certified in accordance with standards such as ISO 9001, ISO 17025, and ISO 17020.

Jan 1, 2019

By C. M. Campbell

THE dire effects of rapidly vanishing natural resources, widespread unemployment, and increased debt and taxation in recent years have challenged Canadians to produce a practical solution to these national economic problems. In more recent months, wars and rumours of war have indicated, among other things, the need for better control of our mineral wealth. The erection of a smelter on the lower mainland coast of British Columbia, treating all Western ores, and such ores as it will be found advisable to import, will make an important contribution toward a solution of these problems. It is believed that the ores tributary justify a smelter of major proportions. A stock-taking to confirm this can be made with reason-able accuracy in a short time, and this should be undertaken without delay. Enough general information is, however, available .in this paper to justify the technicians of the Department of Mines at Ottawa and of interested smelting companies making a preliminary study of the matter. THE DEFENCE ARGUMENT As a factor in rearmament, metals play a vital part. That rearmament is to continue on an increasing scale is indicated in Premier Chamberlain's address of October 3rd last, when he said: ?'For a long period now we have been engaged in this country in a great programme of rearmament which is daily increasing in pace and volume. let no one think because we have signed 'this agreement between the four powers at Munich we can afford to relax our efforts or call a halt in our armaments at this moment'. As matters stand, the facilities in British Columbia are entirely out of line with the strategic importance of this Province as the Western Front of Canada and the Empire. All our copper ores, and an appreciable part of our lead and zinc ores, are sent for treatment to Japan, United States, and Europe, while we import our iron and alloys. A treatment plant on this Coast would not only give us control of war metals and chemicals but it would provide an increased industrial and research population, badly needed in this area and of the greatest value in the case of war. This is where the mining industry can do its bit.

Jan 1, 1939

"The content of production reports has its origins in raw measurements taken in harsh production environments. The ensuing measurement/estimation errors always affect reproducibility such that, regardless of the fact that they are balanced through statistical data reconciliation, reported numbers are simply the most probable values of inferred probability distributions. This has important implications for how metal recoveries should be monitored and reported. Indeed, in a context where many process optimisation activities are based on small improvements in recovery, there should be no doubt that inadequate handling of measurement/estimation errors can easily exaggerate or mask actual changes in process performance. However, estimates of the reproducibility of reported metal recoveries are rarely reported to plant management. This situation persists despite the fact that a code compliant metal accounting system must inform management about business risks related to metal accounting. To this extent, this paper focuses on the continuous management of reproducibility level of metal recoveries in compliance with the best practices. Sensitivity analysis of primary and secondary metal accounting models is performed to show the resulting probability distributions for metal recoveries. Some guidelines are given for designing and managing metal accounting systems capable of achieving and sustaining predefined levels for the reproducibility of metal recoveries.INTRODUCTIONEach and every mineral processing plant produces daily, weekly and monthly production reports in which metal balances for payable and penalty elements are presented. While such production reports are usually consulted in offices, underlying raw measurements are taken in harsh production environments where mechanical vibrations, humidity, corrosion and dust, to name a few, disturb measurement procedures. It is thus no surprise that several authors (Francois-Bongarcon & Gy, 2002; Gaylard, Randolph, & Wortley, 2014; Holmes, 2010; Spangenberg & Minnitt, 2014) have reported pervasive issues related to mass/sampling measurements in the context of mineral processing."

Jan 1, 2016

By B. Dyck, C. Rodgers

ABSTRACT Cameco Corporation is revitalizing its Key Lake Operation uranium mill in northern Saskatchewan. The mill currently uses ammonia stripping in solvent extraction (SX) and ammonia yellowcake precipitation. As part of the revitalization, the company considered installing strong acid stripping in solvent extraction (used at its Rabbit Lake Operation), which would lead to using hydrogen peroxide for uranium precipitation. As part of the process evaluation, tests were carried out to study how the drying temperature in indirect fired dryers would affect the uranium peroxide yellowcake precipitate properties. This paper discusses the test work results, including the relationships between drying temperature and product reactivity with water, product colour, product grade, and energy input requirements.

Jan 1, 2012

By Seungwoo Park, Whuisu Shim, Roe-Hoan Yoon, Kaiwu Huang

"A comprehensive froth model has been derived from first principles. It is based on predicting the kinetics of film thinning in the presence of particles of varying sizes and surface hydrophobicity. According to the Reynolds lubrication theory, the thinning of a horizontal film is driven by the excess film pressure (p), which is determined by the capillary pressure (pc) and the disjoining pressure (II). In the presence of particles, macroscopic capillary pressure (pc) is affected by the local capillary pressure (pc,local) in the vicinity of a particle and the number of particles in the film (N1,film), which in turn vary with the hydrophobicity and size of the particles. The Reynolds equation corrected for pc,local and N1,film is then used to predict the time (or froth height) at which a film is thinned to a critical rupture thickness (hcr), which in turn can be predicted using the Vrij’s capillary wave model (1966) after a modification to incorporate the contributions from hydrophobic disjoining pressure (IIhp). The model can predict bubble coarsening represented by the bubble size ratio between the top (d2,t) and bottom (d2,b) of a froth as functions of particle size and hydrophobicity, ? -potentials, frother dosages, froth height, gas flow rate, salt concentration, etc. The model predictions have been verified in experiments.INTRODUCTIONFroth flotation is regarded the best available technology today for upgrading minerals and coal fines. In the pulp phase of a flotation cell, air bubbles collect hydrophobic particles dispersed in it and rise to enter the froth phase on the top. Once in a froth phase, the bubbles coalesce with each other and become larger, resulting in a decreased bubble surface area. Under conditions of limited surface area, less hydrophobic particles drop off the bubble surface and return to the pulp phase. Thus, bubble coarsening provides a useful mechanism of increasing product grades. On the other hand, uncontrolled coarsening results in a decrease in bubble carrying capacity and hence throughput."

Jan 1, 2016

By K. Woo

"With ever-increasing global demand for mineral resources, mining companies are considering developing deeper, more complex and lower grade ore bodies. Recent years have seen the transition from surface to underground mass mining operations to access deeper resources, with mass mining methods such as block and panel caving being favoured due to the tonnages and economics achievable when dealing with lower grade ore. However, the rock engineering interactions involved with such plans are complex and challenging given the significant disturbance caused to the surface environment. If not properly accounted for, the unexpected propagation of a cave breaking through to surface or the differential surface displacements otherwise produced may threaten the safety and integrity of overlying mine and civil infrastructure.This paper reports the findings of a comprehensive research programme focussed on investigating and integrating new developments in remote sensing characterization and monitoring technologies with state-of-the-art numerical modelling to better manage the challenges and geo-risk associated with the transitioning from open pit to underground mass mining. Procedures were developed to integrate discrete fracture networks (DFN) into finite-element/discrete-element analyses to simulate the influence of rock mass fabric on cave propagation and the evolution of caving-induced surface subsidence and step-path failure of large open pit slopes through the progressive failure of rock bridges. The results clearly showed that caving-induced surface deformations tend to be discontinuous and asymmetric due to large movements around the cave controlled by geologic structures, rock mass heterogeneity and topographic effects. Although parallel investigations of empirical design charts used to predict caving-induced deformations were found to be moderately sufficient for assessing the extent of macro deformations directly above the undercut (i.e. caving collapse features), numerical modelling was found to provide the only means to confidently estimate the lateral extent of smaller strain subsidence.These results were further supported by the use of high-resolution synthetic aperture radar (SAR) data to monitor the ground deformations associated with block caving production, and to use these to calibrate and constrain a series of predictive 3-D numerical models focussed on Rio Tinto's Palabora mine in South Africa. The InSAR data was obtained from Canada’s recently launched RADARSAT-2. The close fit achieved between the predictive 3-D numerical model and InSAR monitoring data demonstrates the significant value of InSAR calibrated 3-D numerical models applied to subsidence prediction.Collectively, the results from this research programme have helped to further the characterization, assessment and understanding of mass mining-induced subsidence, and its evolution, by addressing existing limitations in the use of empirical and numerical design methods. The limitations and uncertainty arising from mine site data were detailed, specifically the representation of mine geology, rock mass properties, in-situ stresses and cave propagation, together with means to constrain these inputs and calibrate sophisticated 3-D numerical models through back analysis and integration with high resolution monitoring data."

Jan 1, 2015

By Bryan Tisch

Goal of GMGE ??To advance mine reclamation through the beneficial use of organic residuals for the sustainable establishment of bioenergy crops and other productive land uses Objectives ??To advance the current ?standard? of mine reclamation by demonstrating that mining lands can safely become agriculturally ?productive? through the use of organic residuals. ??To generate and compile sound scientific data that can be utilized by stakeholders to better assess the environmental impacts of utilizing these materials. ??To complete a manual of best practices regarding the utilization of organic residuals on mine lands. *Considerable effort to be placed on operations/implementation side of utilizing residuals ?rather than just pure research

May 1, 2011

By G. E. Wood

Steep Rock Resources Inc. owns a calcite quarry property at Tatlock, Ontario, and a calcite processing plant at Perth, Ontario. The Tatlock marble deposit forms part of an extensive series of carbonate rocks of the Grenville Geological Province in the Precambrian Shield of southeastern Ontario. The deposit is very unusual, if not unique, in the Grenville area in its combination of characteristics of large size, whiteness, high calcium content, low magnesium and silica contents, and scarcity of accessory minerals. A major expansion of the fine grind products capacity of the plant was undertaken in 1982 and came on stream in 1983. The expansion provides important operating benefits at the plant: greater flexibility as to the product mix and reduced dependence on the single grinding mill previously in place. The expanded facility consists of prima,y and secondary crushers, a rotary drye,~ a screenhouse producing a range of screen separator grade products, an airswept Raymond Mill, and a pebble mill with integrated air classifiers, product storage bins, bulk, semi-bulk, and bagged product shipping capabilities, road and rail access, and a substantial product warehouse. The expansion was designed to be compatible with a move into ultrafine calcite production, and is capable of supplying the anticipated sales growth within its market area during the next 5 years. Products are exceptionally white, with good chemistry, low abrasion, and consistent quality. Markets range, according to product particle size, from pre-cast concrete aggregate to fillers for coatings, plastic pipe, and compounds.

Jan 1, 1984