Search Documents

By K. Östcrdahl

We are developing a cost-saving and environmentally friendly process with low energy consumption to recover the metal content and recycle the acid from spent pickle baths. The metals are precipitated as metal fluorides, which can be turned into metal oxides and hydrofluoric acid by thermal hydrolysis. In the proposed process the solution is concentrated by nanofiltration and the metals are precipitated in a subsequent crystallization step. Different nanofiltration membranes have been evaluated in experimental batch tests. The membrane MPF-34 from Koch Membrane Systems offered both good flux and acceptable metal retention even after long periods of acid storage. The solubility of B-FeF3.3H20 has been measured at varying acid concentrations and at different temperatures. The solubility decreases with increasing hydrofluoric acid and nitric acid concentrations. This suggests that the crystallization process should be operated at high acid concentrations. The crystal growth rate of B-FeF3.3H2O is found to be quite low but increases significantly with temperature. This suggests that the crystallization process should be operated at higher temperatures (40 - 60°C). Within the project a pilot plant has been constructed where the spent pickle bath solution is concentrated by nanofiltration to the desired metal fluoride supersaturation, and B-FeF3.3H2O is crystallized in a 10 L continuous crystallizer.

Jan 1, 2006

By X. Cao, M. Xiao, M. Jahazi

Magnesium alloys have low hardness, wear, erosion and corrosion resistance. The repair of service-damaged aerospace components made of magnesium alloys is an attractive solution in terms of time and cost saving. The feasibility of applying laser beam technology to repair ZE41A-T5 magnesium alloy sand castings in the machined surface conditions was studied using a continuous wave 4 kW Nd:YAG laser system. The influence of process parameters such as laser power, cladding speed, wire feed rate and defocusing distance on the shape, size and area of single cladding beads is discussed using a process optimization software. Sound single clad beads with good geometric characteristics were obtained using strictly controlled laser process parameters. The overall results indicate that laser surface cladding using filler wire has the potential for repairing aerospace components made of cast magnesium alloys.

Jan 1, 2006

By M. Bigdeli Karimi

In this study, the effect of strain level and holding time in semisolid temperature range via SIMA process on AS21 Mg alloy was investigated. Some cylindrical samples of this alloy with 1cm in height and 2.5cm in diameter (H/D=0.4) were compressed to 10%, 20%, 30% and 40% at 300-C. Then, the samples were reheated in semisolid temperature range at 614°C for various times. The results of optical microscopy and image analysis showed that with increasing of strain and holding time, dendritic structure changed to equi-axed structure, gradually. Also, the best conditions to obtain good globular structure were achieved. Furthermore, it was seen that after compression and reheating, Mg2Si intermetallics with Chinese script morphology converted to dispersed-fine particles which were distributed into the ci-Mg grains.

Jan 1, 2007

By Edmund C. Bovey

"AS I begin my remarks this morning, please let me say how honoured and gratified I was to receive your invitation to address you here during your deliberations in historic Quebec City. The high esteem in which your Institute is held is reflected in the respect and deference accorded to it by industry across Canada. I feel privileged to be here with you today.I would like to discuss with you some applications of natural gas in the mining industry and suggest to you, in closing, some possible avenues of future development.Natural gas first became avail-able for industrial purposes in Northern Ontario in late 1958. Acceptance of natural gas, as a source of energy by the industry of that area, has been both widespread and gratifying. The mining industry of Northern Ontario has in-creased its annual use of natural gas by approximately 35 per cent each year since 1958. We believe that this trend will continue, al-though we will probably have to accept a more modest 10 per cent annual gain as the market approaches saturation. I would like to explain how we were able to do this and where all this gas is used. Our first sales were largely a matter of price-and the savings we offered were substantial."

Jan 1, 1966

By K. Meshinchi Asl

In this study the effects of T4 and T6 heat treatments on microstructural characteristics of AZ91 alloy containing Rare Earth elements have been investigated. Formation of intermetallic Al1 1RE3 needle shape particles which have a good thermal stability reduces both formation of ß(Mg17A112) and discontinues precipitation in AZ91 alloy which are dominated at the grain boundaries and are responsible for poor mechanical properties specially in elevated temperatures. For AZ91-RE samples both T4 and T6 heat treatments led to a continuous precipitation of ß particles at the grain boundaries after aging. However, in AZ91 samples (with no Rare Earths) precipitation was discontinuous at grain boundary areas. This type of precipitation is one of the main reasons of poor mechanical properties of this alloy at elevated temperatures.

Jan 1, 2007

By M. Medraj, M. A. Arafin, D. P. Turner, P. Bocher

In this study, the kinetics of isothermal solidification during TLP bonding of Inconel 625 and 718 superalloys with nickel based multi-component filler alloy BNi-2 have been studied through a combination of direct experimentation and mathematical modeling in order to determine the effect of process variables and, thus, to optimize the process. The predicted isothermal solidification completion times from the boron diffusion model and migrating solid/liquid interface model were in good agreement with the experimentally determined values and, they were found to be significantly less than those of other nickel superalloys with different nickel based filler alloys. Further, significant reduction of holding time was observed with increasing bonding temperature and with decreasing joint gap. No significant grain growth in the base metals has been observed in the temperature range being investigated (1325 - 1394K).

Jan 1, 2006

By E. Ghali, B. Arsenault

Aluminum alloys play an important role in the manufacturing of air and ground vehicles. However, with such alloys, corrosion damage is often found on structural components subjected to fatigue loading. The alloying provides large benefit in terms of the high specific tensile strength (ultimate strength/density ratio) to the aluminum alloy but causes the aluminum alloy to be more sensitive to localized corrosion due to complex microscopic heterogeneities such as secondary phases. This paper investigates thermal spray coating namely arc spraying to evaluate the protection against environmentally assisted cracking (EAC) and localized corrosion on Aircraft structural 7075 T651 aluminum alloys. In particular, EAC and pitting corrosion at the interface coating-substrate are a challenge for thermal spray protective coatings on aluminum alloys under cyclic load and immersion. To address these issues, different surface preparation techniques prior to arc spraying were considered such as chemical de-oxidation, laser ablation, shot peening and grit blasting. Results indicate that surface preparation and improved coating process parameters play an important role to provide a coating conferring a protection against both localized corrosion and EAC.

Jan 1, 2006

By R. B. Anderson, N. J. Sherren

The mining equipment at the Scully Mine, Wabush, consists of approximately twenty-five large haulage units, eight large dozer-loader applications and seventy other related pieces of service and maintenance equipment. This equipment is operating in sub-Arctic conditions. This pa-per presents a description of the tire maintenance procedures in use here and discusses the tire troubles that are being encountered and the methods of dealing with them.

Jan 1, 1969

By I. Colquhoun

Current practice tends towards "integrity as an afterthought". That is, integrity is treated as an isolated aspect of operations and maintenance. In fact, this works quite well. But it would work so much better and with less uncertainty if integrity management measures were introduced at the design phase and addressed the entire life-cycle of the pipeline asset. The talk will address the measures and metrics that can be implemented on a new pipeline during design to optimize integrity and deliver a comprehensive operating manual and integrity management program for the pipeline system. This deliverable should describe the risks to be assessed and monitored, and the actions to be taken to control these risk adequately. Properly executed, integrity by design will provide a good working estimate of the life-cycle integrity management costs and maximize system reliability.

Jan 1, 2005

By James McMahon

Although doubt has been expressed many times as to who first brought self-contained breathing apparatus to this side of the Atlantic, there is none whatever that the first organized station was established at Glace Bay, N .S., by the Dominion Coal Company, in 1907. This station was started with 20 sets of 1907 "Draeger" apparatus and all necessary station equipment and supplies. After the fire at No. 1 pit, Sydney Mines, in 1908, the Nova Scotia Steel Company installed 15 sets of "Draeger" and sup-plies, which were housed in a rescue car (a converted pull-man.) In 1909 or '10 a fire occurred at the Back Pit, Stellarton, where the apparatus from Glace Bay was used, and subsequently the Acadia Company erected a station and in-stalled 10 sets of "Securitas" apparatus. In 1912 the station at New Waterford was opened and equipped with "Draeger," and the same year the station at Springhill was built and equipped with the same type. Sometime during past years the Nova Scotia Steel Company acquired a couple of "Proto" machines, and after the explosion at the Allan shaft in 1918 the Acadia Coal Company added some "Gibbs" to their station. From this it will be seen that when the coal-fields were organized under the British Empire Steel Corporation the equipment was rather mixed, therefore steps were taken by the executive to stanardize the whole of the rescue and recovery work.

Jan 1, 1924

By Ken Hester, Bruce Arthur

"Introduction""Pebble milling"" is a term used to describe secondary grinding done with rock pebbles rather than steel balls or other steel or metal shapes. This paper discusses pebble milling with particular attention being paid to uranium grinding circuits.Pebble milling is typically employed:a. where the cost of steel balls becomes exorbitant, as may be the case in an isolated area.b. where the extra steel added from steel ball consumption may be detrimental to further processing.c. where the over-all economics favour the use of pebbles rather than ball.Pebble milling differs from autogenous and semi-autogenous grinding in that a sized product has been removed from some part of the primary comminution circuit, and it is this sized product which is added as grinding media to the pebble milling stage. The pebbles do not necessarily have to be produced from the ore- ""foreign"" pebbles can be used. Also, pebble milling generally refers to grinding from a fine size, below about 6 mesh (3360 micron), with relatively small media, that is, secondary grinding. In South Africa, however, primary pebble mills are sometimes used to grind crusher house product, and thus function in place of rod mills. Pebbles for this service are large and heavy as they must weigh as much as balls used in similar service.The first large applications of pebble milling were in South Africa(n. ""Tube milling"" with pebbles started in 1904. The tube mill was simply a tumbling mill with a length to diameter ratio over two. A ""typical"" early tube mill was 5.5 ft. (1.7 m) in diameter and 16 ft. (4.9 m) in length. Diameters increased steadily. King(n mentions 8-ft. (2.4 m) units in his 1949 book. By 1961, the largest units discussed by Jackson('' were 12ft. (3. 7 m) in diameter."

Jan 1, 1989

By R. Bonifaz

The Chagres Smelter, part of the Anglo American plc group situated 80 Km north of Santiago in Chile, completed a series of operational improvement in 2005 resulting in an optimum capacity in its operational units. At present the Chagres Smelter has developed an operational strategy which seeks to reduce bottle-necks in the production process. In this way we have managed to lower operational cost, decrease energy consumption and maximize the capacity of the Acid, Oxygen, and Smelting, Converting, Refining and Casting units. A constant application of international benchmarks together with continuous staff improvement and the latest smelter technology have combined to place Chagres among the finest smelting works in the world. In response to environmental challenges, we have studying various options for investment suitable for a profitable business of benefits to both Anglo American and Chile as a whole. The most relevant technical indicators are the figures : Energy consumption less than 6,3 GJ/ton fine copper, Intensity of smelting rate in Flash Smelting unit of 6900 ton of copper concentrate/m2 settler of furnace area and be one of the top five smelter in direct cash cost .

Jan 1, 2007

By G. E. Agar, R. Stratton-Crawley

"The applicability of a hydrocyclone model to simulation of the cyclone banks in a multi-stage sandplant circuit producing mine back fill has been demonstrated. The model ha~; been used in conjunction with a modular computer program for circuit simulation in order to study the effect of changes in the operating conditions. It has been shown that weight recovery to sand fill increases as feed percent solids decreases, and, to a lesser extent as pressure drop across the banks increases. An increase in apex diameter also causes an increase in weight recovery. Increased weight recovery must, however, be balanced against sump an1l cyclone capacity and dilution of sand fill by fines. The predicted results from circuit simulation were in good agreement with plant data.The model has been found to be applicable to widely different ores."

Jan 1, 1979

By Ron H. Derammelaere

Coal Slurry Test Pipeline and First Recorded Commercial Pipeline Wallace Andrews founder of New York Steam Company awarded patent for ?Method of Transportation? that involved pumping finely divided coal in slurry form built test facility at Madison Avenue and East 58th Street in New York City died in 1899 in a fire and coal pipeline work was not continued First recorded commercial coal slurry pipeline designed by Gilbert Bell in 1914 to move coal from barges on the Thames River in London to a powerhouse in 8? tubes (660 yards long)

May 1, 2013

By W. M. G. Heeley

In the province of Alberta the coal measures dip at so many different angles, between the horizontal and the vertical, that many different systems of haulage are in use. I will, however, only touch briefly upon the general -systems in use, and devote the major portion of this paper to a discussion of endless-rope haulage and its adaptibility to various conditions in coal mines; dealing in particular with the endless-rope haulage that was installed at Brule during the month of August 1923. In coal seams that are approximately level, and newly opened, hand-putting or tramming from the face is the cheapest, but when the mine is further developed tramming is out of the question, and the use of ponies is the next consideration. The time arrives, however, when mining reaches a point where the economical haulage of coal by horses cannot be done profitably, and then some system of mechanical haulage must be installed. The installation of any system should be carefully considered before any particular type of haulage is adopted, because a great deal depends upon the grade or dip of the seam. Motor haulage is impossible to operate profitably on a grade of over 6 per cent and, while it is possible to use ponies, on short runs, up to 9 per cent, some other means of main and secondary haulage must be installed when a 9 per cent grade, is exceeded. I will, therefore, deal first with secondary haulage, because even though a main haulage is established, secondary haulage can be used to feed the main haulage.

Jan 1, 1925

By K. N. Bolatbaev, S. S. Naboichenko

The initial rates of dissolution of pyrite, chalcosine, sphalerite and galena in acidic sulphate solutions under oxygen pressure were measured in the range of Poe = 0.2-1 MPa, 130-180 °C, [H2SO4]0 = 0.2-0.7 M, and in the presence of surface-active agents and agitation producing Re = 4-16 x 103. Reaction orders, activation energies, and values of reaction constants for these oxidation reactions were established. The reactions also were shown to be diffusion-controlled; and the rates demonstrate a linear dependence on the surface area of the sulphides. A surface reaction model, in which oxygen is transported through a solid layer of surface products, has been advanced. The initial stage of high-temperature interaction at pH <7 is suggested to involve a chemical activation of the sulphide surface and is described by the following general reaction: MenSm + H3O+ Men-1 Sm-1 (HS-)s + H2O The subsequent oxidation of surface complex HS- to S0 or SO2-4 occurs with the assistance of Fe(III), Cu(II) ions depending on temperature and the redox potential of the medium, which are defined by oxygen pressure and composition of the reaction mixture, especially concentrations of H2SO4 and metals with variable valence. General process kinetics are complicated due to the formation of by-products on the basis of Fe3+ Pb2+, Cup ions, which displace the kinetics into the diffusion region.

Jan 1, 2004

By Ibrahim Ocak

The prediction of machine utilization time and determining machine performance plays an important role in scheduling and planning tunnel excavation and data base created serve a major role in further applications. In this study, the construction methods of two twin tunnels situated between Basak Konutlari station and Istoc station are summarized. Geology in the study area is composed of fill and weak rock, respectively starting from the surface. The tunnels of 5.6 km in length were excavated with two different earth pressure balance machines (EPBM). Excavation diameters of the EPBMs were 6.564 m. The performance of the machines are analyzed and compared in order to accumulate data for further applications in similar ground conditions in Istanbul. The distance between two twin tunnels is 14 m from center to center and the EPBM in the one tube was almost about 100 m behind the other tube. Segmental lining with 1.4 m of length and 30 centimeters of thickness were used as final support. The overall performances of the two Lovat TBMs are found to be respectively as; the best daily advance rates 30.8 m/day and 30.8 m/day, the best weakly advance rates 115.0 m/day and 153.9 m/day, the best monthly advance rates 388.7 m/day and 400.5 m/day. Total waiting and maintenance times were 25.2 and 16.7 %, respectively.

Aug 1, 2013

By A. R. Sheik, A. A. Baba, M. K. Ghosh, K. Sanjay, R. B. Bale, A. G. F. Alabi, F. A. Adekola, L. Ibrahim

"This paper studies the characterization and dissolution of a Nigerian pyrolusite ore, reporting the results of ore physicochemical analyses and detailed ore characterization before and after leaching at optimal conditions. Ore dissolution rate increased proportional to acid concentration and temperature, but decreased with ore particle size. In a 4 M H2SO4 solution at 80°C with a particle size of –90+75 µm and moderate agitation, ore dissolution rate reached 78.7%. Unleached residue produced under optimal leaching conditions consisted of silica with admixtures of cristobalite and stishovite. The calculated activation energy supported the proposed diffusion control mechanism for the process.RÉSUMÉ Le présent article étudie la caractérisation et la dissolution d’un minerai de pyrolusite du Nigeria, il donne les résultats des analyses physicochimiques du minerai et de la caractérisation détaillée du minerai avant et après la lixiviation sous des conditions optimales. Le taux de dissolution du minerai augmentait proportionnellement à la concentration de l’acide mais décroissait avec la taille des particules. Dans une solution 4 M H2SO4 à 80 °C, avec une granulométrie de –90+75 µm et une agitation modérée, le taux de dissolution du minerai a atteint 78,7 %. Les résidus produits sous des conditions optimales de lixiviation étaient constitués de silice avec un mélange de cristobalite et de stishovite. L’énergie calculée d’activation supportait le mécanisme de contrôle de la diffusion proposé pour le procédé."

Jan 1, 2016

By Ifeanyichukwu Nweke

"Aluminium rolling processing from ingots to cold rolled coils comes with a lot of challenges especially in controlling defective products in casting, hot mill and cold mill operations. Hence this study focused on reducing defects at mills and cast-house using six sigma approaches. The use of six sigma approach will help the production experts to determine the gap between its operation and world class process. Practical data from First Aluminium Rolling mills were presented and analysed and mini improvement projects were proposed based on organisation need to achieve excellence. This study encourages aluminium alloy industries to pursue process improvement projects on the basis of analysis on data obtained from their shop floor, hence ensuring that through this, recovery is improved and cost of poor quality is reduced.INTRODUCTION Engineer Bill Smith while working at Motorola in 1986 introduced a new concept in which a set of techniques and tools are used for process improvement by controlling variations (defects). These tools and techniques are explained by an acronym DMAIC. D DEFINE the problem M MEASURE the variables in the problem A ANALYSE the variables of the problem I IMPLEMENT and verify the solution to the problem C CONTROL the solution to sustain it Most times in six-sigma approach, variations in the process that results in defects and customers’ dissatisfaction are targeted at 3.4 defects per million opportunities. There are numerous methods six sigma application use to achieve quality results and innovative strategies. Improving the quality of process through these methods helps identify and reduce variations which paves way for organisational excellence. In this study, it is encouraged to use six sigma techniques to improve aluminium rolling operations and other aluminium processing activities, the benefits of such improvement concept include: • Satisfy the voice of the customer (VOC) • Minimise costs • Maximise Profits • Build Good Team • Implement Profitable Project"

Jan 1, 2018

By V. L. Eardley-Wilmot

Diatomite as prepared for the market is a fluffy, white powder, remarkably light in weight-it weighs only 10 to 15 pounds per cubic foot, or one-tenth as much as sand. Being extremely porous and inert, it is in large and increasing demand for insulation and filtration purposes, as general filler, and for many other uses. Structure Structurally, diatomite is quite different from any other known commercial material. It is composed of myriads of microscopically small, siliceous shells of diatoms which belong to a group of flowerless aquatic plants called algae. When these plants die, the siliceous remains sink to the bottom of the water and form beds of diatomite. Over 8,000 species of diatoms are known, named, and tabulated. The intricate scroll-work and patterns on many of these are one of the marvels of nature, and yet so small are they that from 40 to 70 million separate diatoms may be contained in one cubic inch of material. However, the size and shape of these diatoms, which vary greatly (compare Figures 5 and 6), have an important bearing on the commercial use of the diatomite. The diatoms in the majority of the known deposits are so typical of that deposit that, after a micro-examination, an expert can usually tell not only from what part of the world, but also from what particular deposit, the sample has come.

Jan 1, 1931