Search Documents

By M. M. Papic

"This paper describes the Sasol coal liquefaction process, as used in South Africa. It covers coal supply, coal gasification, gas purification, Fischer-Tropsch synthesis, the major utility systems involved and the economics of the process.IntroductionThe Sasol coal liquefaction process is based on Fischer-Tropsch synthesis of liquid fuels from carbon monoxide and hydrogen, which are in turn obtained by gasification of coal with steam and oxygen. The process is shown schematically in Figure I.The first step in the process is coal preparation, in which the coal is crushed and screened to a 3-50 mm size for gasification on one side and to -3 mm size for steam and power production on the other. Oxygen needed for coal gasificatoin is produced in the air separation plant.Coal is gasified under pressure by steam and oxygen in the Lurgi gasification plant, where raw, impure gas is produced . The raw gas is first washed in a scrubber with a circulating gas liquor, heat is then recovered from it in a waste heat recovery boiler and the gas is further cooled for purification. Water-insoluble materials (tar oils) in the gas liquor are separated from aqueous solution and sent to tar refining for the recovery of tar products. The aqueous portion of the gas liquor goes to a Phenosolvan solvent extraction process, where phenols and ammonia are recovered. Water then proceeds to the effluent treatment plant.The scrubbed and cooled raw gas goes to a Rectisol gas purification plant, where all components other than hydrogen, carbon monoxide and methane are removed as completely as possible by absorption in refrigerated methanol. The acid gases (CO2, H2S) stripped from the methanol in the Rectisol unit are processed in a Stretford plant for recovery of sulphur. Regenerated methanol is returned to the process. The purified synthesis gas is passed to the fluidized-bed Synthol reactors, where Fischer-Tropsch synthesis reactions take place.The synthesis products are recovered in a product recovery unit as separate streams of decant oil containing higher-molecular- weight hydrocarbons, light oil comprised of lower-molecular- weight species, the aqueous stream containing water solubles, a C3/C4 stream, a C2 stream , a methane stream and a hydrogen-rich stream. Most of the hydrogen is recycled to the Synthol reactors; a major portion of the methane is reformed to hydrogen and carbon monoxide for recycle; the C2 fraction goes to an ethylene plant; and liquid streams proceed to the product refinery.The product refinery is used to upgrade and purify the Synthol products to specification fuels and chemicals.Sasol l, the first coal liquefaction plant in South Africa , was built in 1955. It is still operating and has a product output of about half a million tonnes per year. The Sasol II plant is in a commissioning stage and will be in full operation in 1981. It is about five times the size of Sasoll. It uses over 12 million tonnes of coal and produces more than 2 million tonnes of saleable products annually (1,2,3). The Sasol llI plant, which is a mirror image of Sasol II, is under construction and scheduled for completion in 1983."

Jan 1, 1981

By M. Timmins

Campbell Mine operates a 100 tpd gold autoclave that treats sulphide concentrates at 305 psi and 200 °C. Autoclave feed consists of fresh pretreated concentrate, an acidic oxide slurry recycle as well as other high arsenic sources. The brickwork that is used to construct the five compartments of the vessel must be inspected and repaired periodically. Shutdowns are scheduled to inspect this brickwork and at times replace entire sections of the brick walls or lining. It also provides an opportunity to repair or replace other internal features such as agitator blades or oxygen spargers. Mechanics and contractors are scheduled around the clock to perform the maintenance requirements. There are many safety considerations and precautions that must be taken in order to protect the well-being of the workers and minimize damage to sensitive pieces of equipment. Heat, arsenic and lead contamination and confined space issues are just a few of the hazards involved. The following paper will describe how these safety concerns are addressed and will serve as a guide for future autoclave shutdowns.

Jan 1, 2004

By Karl J. C. Harries

"The Table of Contents that follows is only an example and is the Table of Contents from an actual negotiated agreement. It is merely intended to show how an agreement might be set out and the nature of possible provisions. As a negotiated agreement the format was dictated by the negotiations. It is not offered as a precedent of what should be contained in a joint venture agreement (“JVA”), the “proper” sequence of Articles, or a complete listing of the contents of joint venture agreements generally. The set-up used for an agreement should be decided by the parties and be one they consider flows in a logical and workable sequence. This example sets out the “deal” first, followed by the provisions relating to how work is to be carried out and then by administrative provisions necessary to make the agreement work. If you are more comfortable with, say, having the Committee provisions at the beginning, by all means have it drafted that way -- you are going to have to live with the agreement and work under it.Notes:1. The Table of Contents provisions appear in bold print. The italicized sections are annotations, which have been provided in some cases where the heading may not clearly describe the contents. They are not intended to be comprehensive, but refer to some specific matters that are considered to be of interest or to need some clarification.2. The subject matter of many of the articles and paragraphs is discussed or commented upon in the text of the book. Some of section cross-references have been provided. Such references are only to sections where the topic is a principal subject and no attempt has been made to provide a comprehensive indexing.3. Although this particular agreement is a three-party agreement, *B* and *C*, the Owners, are required to act as a unit (see para. 1.09. – § 8.44.), making the agreement effectively a two-party agreement. The parties insisted upon having a decision-making Committee and structuring the agreement accordingly. As is explained in § 8.11., such an arrangement is not recommended and can result in problems.5. See also §§ 8.24., 8.41. and 14.13. for discussions on tables of contents, summaries, and headings."

Jan 1, 2003

By J. Ji, A. Shi, B. Grcic

Floating copper minerals selectively against iron minerals such as pyrite has been challenging for most copper and copper/gold deposits, and many operations continuously strive to maximise copper recovery whilst meeting target concentrate grades. Maximising grade is achieved by selectively floating copper minerals and rejecting pyrite. This challenge is to minimise copper and gold losses in the roughers if this approach is used. A flotation testing program was conducted by Bureau Veritas Minerals on a high-level pyrite bearing copper/gold ore sample to establish the potential to reject pyrite in the rougher stage, but also maximise copper and gold recoveries, and ultimately final product grades. The test program included feed characterization, rougher and open-circuit cleaner flotation as well as locked cycle flotation tests. The main variables tested for achieving selective flotation of copper and gold were collector type and pH control, through lime addition. Grind sizes used in the rougher and cleaner tests had been established from previous test work. The collectors tested were SIPX, Aerophine® 3418A, Aerophine® 3421, Aerophine® 3422, Reagent S-11192 Promoter, Reagent S-11193 Promoter and FloMin C4150. The two best performing collectors were then tested in open-circuit cleaner tests, with the optimum conditions examined further in locked cycle tests. INTRODUCTION Bureau Veritas Minerals Metallurgical Division was retained by Eldorado Gold Corporation to perform a metallurgical testing program on a high-level pyrite bearing copper/gold ore sample from a gold- copper porphyry deposit to optimize flotation reagent scheme to improve gold and copper recoveries and copper content in the concentrate. The test program included feed characterization, rougher and open-circuit cleaner flotation as well as locked cycle flotation tests. Initially, various collectors were screened in kinetic rougher tests, and over a pH range of 8.5 (i.e the natural ore pH) up to 11.5, using a primary grind size of 80% passing 120 µm. The collectors tested were SIPX (sodium isopropyl xanthate), Aerophine® 3418A, Aerophine® 3421, Aerophine® 3422, Reagent S-11192 Promoter, Reagent S-11193 Promoter and FloMin C4150. The enrichment ratio, which is the ratio of copper to sulfur in the concentrate to that in the feed, was used as proxy for rating selectivity (i.e. degree of pyrite rejection or depression).

Jan 1, 2019

By L. Voisin, G. Damm

"In order to develop a new pyrometallurgical process for eliminating detrimental arsenic and antimony from the impurity-rich matte produced from copper concentrate, and for treating the occasionally generated speiss in nonferrous smelting processes, the phase relations in the Fe-Cu-S-As-Sb system saturated with carbon at 1473 K were investigated. The distribution of elements between the condensed phases at the miscibility gap, where three equilibrated phases of iron-rich alloy, copper-rich alloy, and matte coexist, were also studied. The investigation was carried out by performing a series of laboratory scale experiments in an electrical furnace at 1473 K, followed by a quenching method on the final stage. The samples obtained from the experiments were analyzed by using Inductively Couple Plasma (ICP), Atomic Absorption Spectroscopy (AAS) and Carbon Infrared Spectrometry (CIS) techniques.The results were compared with previous investigations for the Fe-Cu-S-As-C and Fe-Cu-S-Sb-C systems and discussed on the basis of the molar fraction distribution for both arsenic and antimony in the matte phase at five different matte grades. It is expected that by using this phase separation technique it might be feasible both, the cleaning of a complex copper matte and the elimination of arsenic and iron together with an acceptable amount of antimony into the iron-rich alloy phase, which can be discarded as a harmless and smaller deposit."

Jan 1, 2014

By M. Barati

A collaborative research between University of Toronto and Hatch was conducted to understand and optimize the process conditions pertaining to a novel steelmaking technology. In this technology, known as CRISP, direct reduced iron is continuously melted and refined in a stationary electric arc furnace. The major challenge against continuous operation of the electric furnace was identified to be minimizing the corrosion of the refractory in order to achieve uninterrupted operation for a minimum of one year. Theoretical analysis and bench scale experiments together with two pilot runs resulted in defining an operating window for slag chemistry that would minimize chemical attack to the refractory while satisfying the oxidizing conditions required for sufficient decarburization. An analysis of the process in terms of energy consumption and emission of greenhouse gases revealed that it is superior to the current batch DRI-based steelmaking technologies.

Jan 1, 2011

By Xuanxue Mo, Zengqian Hou

"Abstract -Yidun Island Arc in Sanjiang Region is one of the important Kuroko-type volcano­ genic massive sulfide deposits (VMS) districts in southwestern China. Tectonically, the region is situated in the eastern portion of the Tethys orogenic belt, and is a late Triassic extensional island-arc. The island-arc underwent earlier arc construction, intra-arc rifting, later arc construction and back­ arc spreading during its evolution and formed a complete trench-arc-basin system, i.e., the Ganzi­ Litang suture zone, forearc basin, outer arc, intra-arc rifting zone, inner arc and back-arc basin from east to west across the island-arc.Kuroko-type VMS deposits and occurrences discovered so far are limited to within the intra-arc rifting zone of the Yidun Island Arc and tend to occur in groups or clusters distributed in separate fault­ bound basins; e.g., Zengke, Gacun and Xiangcheng basins, in which submarine volcanic rocks, especially bimodal volcanic suites, were extensively developed. The VMS deposits formed in the waning stages of volcanic eruption in the late Triassic and are hosted in the uppermost section of acidic volcanic rocks (rhyolitic-dacitic) within a bimodal suite. The orebodies are associated with these host rocks: rhyolitic-dacitic pyroclastic rocks and exhalites and chemical sedimentary rocks.Ali VMS deposits in Sanjiang are of the Zn-Pb-Cu type. The architecture of the deposits is two­fold, consisting of concordant lenses and layers of massive sulfides and an underlying discordant stockwork. Ali deposits show metal zoning. The hydrothermal alteration related to mineralization is strong and asyrnmetrical, and is found dominantly within the stockwork zone and host rocks surrounding the ores. There are two alteration patterns: (1) chloritization - sericitization - silicification from outer sides to core of the alteration pipe; and (2) silicification + sericitization - silicification + carbonate from the lower to upper part of the alteration pipe_The mineralization temperatures of ore-forming fluids vary in the range 200°C to 335°C. Thermal evolution of the fluids displays temperature profiles that first increase and then decrease with progression of mineralization processes. The majority of black-ore minerais (Groups I and II) formed during intensifying stages of hydrothermal activity, and the majority of serni-yellow-ore minerals (Group III) formed during a thermal maximum . There followed the formation of fine-grained black-ore minerals (Group IV), which interacted with barite layers during decreasing temperature phases.Oxygen and hydrogen isotope studies show that the sources of ore-forming fluids for the Kuroko­ type VMS deposits are two-fold: seawater and magmatic hydrothermal solutions, represented by the Kuroko deposits in Japan and Kuroko-type VMS deposits in Sanjiang, respectively. In the latter case the hydrothermal solutions reacted with host rocks and mixed with cold seawater percolating downward, and circulated through volcanic rocks resulting in development of alteration zones and formation of ore minerals in Kuroko-type VMS deposits."

Jan 1, 1993

By Alisa M. Caswell

Outline: 1. Syncrude: Who are We? 2. Energy Use at Syncrude 3. Historical Energy Focus at Syncrude 4. Case Studies for Process Variable Monitoring 5. Extraction Flood Water Temperature Management 6. Fired Heater Tuning 7. Critical Factors for Success Syncrude: Who are We? ?Syncrude is a Joint Venture Operating Company with one product: Synthetic Crude ?Production Capacity: 350 kbbls/day ?Primary Energy Sources: ??Fuel Gas + Natural Gas ?? Coke ?? Electricity ?? Diesel

May 1, 2008

By Jianwen Yang, Yucai Zhou, Yanhong Dong, Daixiong Chen

"The study of combined depressants for flotation separation of lead from copper has been carried out to solve the copper-lead separation problem. Test results show that the depressant of CMC (Carboxyl Methyl Cellulose) or sodium sulfite plays an important role on the selective depression of galena flotation. When the two reagents above are combined, the selective depression effect on galena is further enhanced. When the mass ratio of CMC to sodium sulfite is 1:4, galena was best depressed, with the lowest lead content in the copper concentrateClosed-circuit tests indicate that under a certain pH value of the slurry, with the best ratio of CMC to sodium sulfite as depressants, the copper concentrate with the grade of 28.23% copper and 4.12% lead is obtained, and the copper recovery is 84.87%; the lead concentrate with 68.12% lead and 0.86% copper is obtained, and the lead recovery reaches to 92.20%. An efficient separation of copper and lead is achieved with the combined depressants. INTRODUCTIONComplex copper-lead-zinc sulfide ore is abundant in China. With the rapid increase of mineral consumption, it has become one of the important sources to produce copper-lead-zinc metals. However, it is difficult to achieve effective separation of copper and lead, due to the complicated ore properties, such as fine dissemination, low copper grade, complex symbiotic relationship and similar floatability of copper and lead.Poisonous reagents of bichromate and cyanide are often used as depressants for copper lead separation. They have good separation efficiency, but pose serious pollution issues. As the environmental protection is becoming more and more important, it is a trend to replace traditional toxic reagents with new nontoxic efficient chemicals. Organic depressant FCLS studied by Liu has strong selectivity against galena, and does not depress chalcopyrite. A new type of galena depressant of CLS-01 discovered by Jin-lin Yang shows good results in the separation a mixed copper and lead concentrate. In addition, dextrin, chitosan and some other natural organic compounds (Drzymala, 2003; Huang, 2012; Qin, 2013) have also been studied to separate copper and lead."

Jan 1, 2016

By E. Demedde

Carbon anodes in aluminium reduction cells are continuously consumed during electrolysis. In prebake cells the anodes are replaced at regular intervals. The spent anodes, called butts, are often allowed to cool in air while emitting fluorides into the building from the hot alumina cover and the adhering bath. In modem smelters spent anodes are placed inside enclosures and fluoride emissions during cooling are effectively reduced. Fluoride emissions from spent anodes were estimated by considering the kinetics of fluoride formation, a heat transfer analysis of the cooling anode butt and the ventilation flow from a cavity. Fluoride emissions from large anode butts cooling inside enclosures were compared with those cooling in air. Good agreement with published experimental values was obtained for enclosures having different leakage opemngs, when a hydrofluorination reaction of the spent anodes was included.

Jan 1, 2006

By JOHN DUNFIELD

Good quality sphagnum peat bogs occur across Canada in areas of ample rainfall and cool, temperate climates. Early peat production techniques were restricted primarily to hand digging blocks of peat and piling them up to be dried by sun and wind. Suburban de velopment in the 1950s and the concomitant spread of home gardening triggered a dramatic growth in peat demand; labour costs rose in the same period. Peat production techniques had to alter accordingly. The three mechanical inno vations attempted were hydraulic mining, mechanical block digging and vacuum harvesting. Of these, the last method pro ved the most successful in Canada and is used to harvest 80% of Canadian peat production. Escalating transportation costs are the most important feature affecting future development of the Canadian peat industry.

Jan 1, 1984

By Yan-Jun Shen

The rock mass classification system, BQ (basic quality), is the only national system that is suitable to most kinds of rock engineering in China. It uses two main aspects of the rock mass, the intact uniaxial compressive strength (UCS) and the rock intactness index (KV), to obtain the rock mass BQ. The index KV could be measured by the acoustic wave method. However, because this method is an indirect approach to characterize the rock mass structure, misfits often occur between the test results and the actual rock mass characteristics. Therefore, a new parameter KGSI expressed by the geological strength index is proposed to replace the original KV, and a new method is presented to express the value of BQ as a function of the UCS and the KGSI. Then, the underground excavations at five hydropower stations were chosen as examples to study the relationship between the revised BQ and the each of the international systems (RMR, Q or RMi). In addition, the applicability of the RMR, Q, or RMi system is discussed for China?s rock characteristics and geological conditions, and suggestions are given for improving the revised BQ system.

Aug 1, 2013

By D. Raicevic

After more than 93% of the uranium is extracted from Elliot Lake uranium ores by a sulphuric acid leaching process, the leach residue (tailings) contains small amounts of uranium and radioactive isotopes, particularly radium-226, which is the most serious health hazard. Heavy metal components and pyrite are also present, along with the gangue minerals. Currently, over /000 acres of the Elliot Lake area are covered with these tailings, which contain over five million tons of pyrite. Because of constant oxidation of the pyrite by bacteria (thiobacillus) and the presence of moisture, pyrite slowly generates sulphuric acid, which steadily leaches the metal-bearing constituents from the tailings. The seepage-flows of the dissolved contaminants, although often quite low in volume, have an environmental impact on the Elliot Lake area. Although these seepages are treated and most of the contaminants removed and impounded, a small amount of the radioactive contaminants reaches Lake Huron via the Serpent River. This paper describes a flotation approach for treatment of the Elliot Lake uranium tailings to produce new, decontaminated tailings practically free of pyrite, with radium, thorium and uranium contents considerably reduced. The decontaminated tailing produced, which comprises about 75% by weight of the current uranium tailings, appears to be suitable for mine backfill. Because mine backfilling normally uses about 50% of the plant tailings, the surface storage of about half of the uranium tailings, therefore, would be eliminated by this process. Mine backfilling would also increase the mine production and thus enlarge the over-all uranium resources due to recovery of the ore from pillars. The pyrite concentrate produced from the current uranium tailings would be suitable for sulphuric acid production. The possibility of uranium recovery, and disposal of radium and thorium from the concentrates produced, is now being studied at CANMET.

Jan 1, 1979

By M. Aushouri, S. H. Mansouri, N. Aminizadeh

A thermo-chemical model of the Peirce-Smith copper converter in blowing the copper stage has been developed to predict the molten temperature. The key assumption of the model was that white metal and gas phases in the converter were in thermal and chemical equilibrium. In this model, the chemical reaction of white metal and oxygen was accomplished completely. So long as sulfur existed in the bath, the generation of Cu2O was frozen. The reaction rate was considered to be constant and controlled by the reacted sulfur. The converter temperature was calculated by heat balances over time. The model was validated by a detailed comparison with measured industrial data. A good agreement was obtained. The converter temperature depended on process parameters such as oxygen efficiency, molten emissivity and oxygen enrichment.

Jan 1, 2007

By D. A. Beck

The load-deformation response of discontinuous rock under static and dynamic loading conditions has been simulated using Explicit Finite Element models. The intent of the analysis was to investigate the effects of specimen size and confining stress on strength, dilation and comminution. The simulations allow the development of homogenised constitutive material properties for discontinuous rock masses using laboratory scale measurements and representative Discrete Fracture Networks (DFNs). A procedure for this is presented which includes a comparison of measured seismic response in a mine to the Dissipated Plastic Energy (DPE) that is released in the simulated rock masses. The models also show how confinement and scale affect the stress-strain and DPE response of the simulated rock specimens, reproducing a number of known rock phenomena that are often poorly captured in geotechnical modelling. A case study is presented showing a satisfactory match between the model-derived, homogenised material properties and values achieved by calibration of a mine-scale model where many thousands of seismic, displacement and damage measurements were available.

May 1, 2009

By J. O. Marsden

Over the past decade, the copper industry has been through an extended downturn followed by several years of sustained high copper price. A number of new technologies have been developed over the past 10 years aimed at reducing costs by decreasing energy, labor, and materials requirements, or by increasing metal recovery. The energy intensity of different copper extraction routes and different technologies varies considerably and this has a significant impact on the economics of extraction. Based on average ore grade materials, the total energy for the extraction of copper typically varies from about 24-26 MJ/lb (6.7-7.2 kWh/lb) for the mining, crushing, milling, flotation, smelting and refining route to about 14¬16 MJ/lb (3.9-4.5 kWh/lb) for the mining, crushing, heap leaching, solution extraction and electrowinning route. New technology developments are providing opportunities for significant reductions in energy consumption for copper extraction, representing energy savings up to 20-25% in some cases. In addition, in many cases, these new technologies have introduced environmental, safety and health benefits over the incumbent technology. Some of these technology developments have been more successful than others, and many hold great promise for application in the coming decade. This paper provides an overview of the technology developments that have occurred, and explores the underlying reasons behind successful implementation.

Jan 1, 2007

By T. H. Patching, M. W. Mikhail

"Data from a standardized procedure for measuring methane desorption rates from samples of Western Canadian coals gave a good correlation (0.994) with the percentage of fines (-0.6 mm) found in the corresponding run-of-mine coal. The correlation was independent of the mining method and the top size of the samples. It is suggested that both methane desorption rate and the production of fine coal sizes are functions of the fissuration of the coal being mined.This relationship, in conjunction with established data of degradation by unit process equipment, may be useful in predicting the amount of fines that will be produced from new seams of coal and by planned new washeries. It also could be a valuable guide in modifying existing washery processes to minimize production of fines."

Jan 1, 1980

By Claude Bazin, François Robichaud

The control of the operation of a semi autogenous grinding mill is mainly based on power and bearing pressure measurements. Image based sensors can provide on-line measurements of the size distribution of the ore feeding a SAG mill allowing the control of this variable that impacts the operation of this equipment. This paper investigates the potential of using the information from such type of sensor to maintain a SAG mill feed target size distribution by manipulating the speed of the ore extractors below an ore stockpile. A PID and adaptive predictive controller for the size distribution are studied using a simulator for a stockpile and the equipments used for ore withdrawing from the pile. The proposed controller is found to give a good performance while remaining easy to tune.

Jan 1, 2014

By Radford B. Langston

Mining Methods Majority of Production Ramp and Fill at Stillwater, Sub-level Becoming More Important Production at East Boulder from Sub-level l Majority JM REEF ROCK TYPES NORITE - plagioclase and bronzite cumulate GABBRONORITE - plagioclase, augite, and bronzite cumulate TROCTOLITE - plagioclase and olivine cumulate ANORTHOSITE - plagioclase cumulate PERIDOTITE - olivine cumulate

May 1, 2002

By Walter Greaves

THIS paper describes a series of tests performed at the Hollinger mill during the past four years, in which both metal and rubber-lined pumps were used for pumping sand and slime. While conditions will not be the same at other mills, it is felt that the information gained from the tests should be of value to other operators and of assistance to them in selecting the most efficient size of pump and kind of lining for economical operation. For the successful operation of pumps with rubber linings there are certain conditions, which, if recognized at the outset, will save the operator a good deal of work and trouble. First is the necessity of keeping sharp pieces of steel, or anything that might cut the lining, out of the pumps. This can be effected by placing screens in the proper locations. Second is to recognize the fact that the rubber lining of the shell, and the rubber cover of the impeller, are subjected to very different conditions. The shell lining, :being at rest and well supported by the metal case, has a relatively easy job compared ? with the impeller covering, which is subjected to centrifugal force and has a tendency to tear itself away from the metal core. Also, the pulp travels through and past the impeller at a high velocity. These two factors, centrifugal force and velocity of the pulp, would appear to set a limit to the speed at which, for a given set of conditions, it is economical to run a rubber-covered impeller. Therefore, a pump should be large enough for the work to be done. To get the best mechanical efficiency, it must be operated somewhere near the limit of its capacity, but this may not give the best overall cost, because the saving in power, due to the high efficiency, may easily be lost through excessive wear on the lining. It would appear that this condition is more critical in a rubber-lined pump than in one lined with metal.

Jan 1, 1939