Search Documents

By Steve Piercey

Introduction ? VMS Deposits: The Target ? Key points for every belt: heat flow and extension. ? Good felsic rocks ? Good mafic rocks. ? Petrochemical assemblages. ? Summary Key Points Throughout ? Common themes: ? Heat ? driver of the hydrothermal system ? Extensional geodynamic setting ? conduits to focus fluid flux ? (e.g., Lesher et al., 1986; Swinden et al., 1991; Barrie et al., 1993; Lentz, 1998; Syme et al., 1999; Piercey et al., 2001, etc.) ? We must identify rocks, belts and tectonic environments that encompass these two criteria (among others but?) ? e.g., forearc rifts, intracontinental rifts, arc rifts, and back-arc basins.

Apr 1, 2005

By D. E. Keeley

lntroduction Some years ago it was general practice in Canadian mines to use the best timber available, just as it was cut from the tree. Later, to prevent 'borers' from getting into the wood while stacked in the yard, the bark was peeled off, cleaned up carefully, and burned to eliminate a breeding ground for these and other destructive insects. This practice of good housekeeping also decreased the hazard from fire in scattered bark. A few years after damage by borers had been minimized, it became apparent that increased temperatures in the mines, occasioned by deepening operations, were being accompanied by rapid growth of fungus and by decay in timber underground, greatly shortening its life. In places on upper levels where the air temperature was below 50 deg. F., untreated timber retained a large proportion of its strength for ten or more years. In other places on these levels, however; its life was short and it developed much dry rot and merulius lacrymans. In these latter places and on lower levels in the mine where temperatures ranged from 50 to 60 deg. F., approximately, the wood became infested with extensive growths of this white fungus. This development was accompanied by the production of millions of spores. Spread of infection was due mainly to the transfer of spores from the warm lower levels to the cool upper horizons by upcasting ventilation currents. So serious did this become that about twenty years ago Lake Shore, Hollinger, and McIntyre Mines decided to investigate the use of wood preservatives and the plant necessary to treat timber.

Jan 1, 1949

By G. G. Bowser

PERUSAL of a list of present-day commercial explosives perhaps does not convey a full realization that there has been a great deal of improvement since the original dynamite was discovered nor that, in recent years, great developments have taken place in specialized explosives. This is true particularly of high-explosives for use in metalliferous mining or what is more commonly termed 'hard-rock' mining. Not many decades ago, only two or three types of explosive were avail-'able for commercial use. One was black blasting powder. Another was ordinary nitro-glycerin dynamite in various strengths. Black blasting powder remains with but very little change. Despite its ancient lineage, it is still with us as perhaps the sole explosive in use today which is almost identical in appearance, physical properties, and working ability or execution co the original. Which dynamite the story is different. Its evolution may be likened to that of the dog, nitro-glycerin as first discovered being the counterpart of the wild dog and, like it, dangerous and hard to control. The original dynamite as made by Nobel might then be considered as representing the first domesticaced species. This original dynamite, however, has been 'crossed with other bloods' until one sees now many distinct 'breeds' in the list. Present-day explosives still have the 'bark' and the 'bite', but with control and research have come many improvements; and types have been created which are specially adapted for particular kinds of work. We still have the direct descendant of Nobel's dynamite in the form of an improved nitro-glycerin dynamite. This C-I-L explosive, Polar Dynamite, is no longer the best type to use in the hunt for gold, silver, iron, and other metals. There have been developed other explosives more suitable for chat work. In Canada, such explosives are accomplishing this work effectively, not only where climatic conditions are moderate but through the rigours of our northern winters, with their sub-zero temperatures.

Jan 1, 1938

By A. B. Walker

The effects of the injection of dry limestone additives into boilers for the sorption of sulphur dioxide have been studied in pilot and full-scale systems. The effects of such injections on boiler mass particulate emissions as well as collectability characteristics of the fly ash and reaction products are presented. Implications of the effects on the design and economics of particulate collectors, in particular electrostatic precipitators, are discussed.

Jan 1, 1971

By B. Simser, V. Falmagne

"Noranda’s Brunswick mine is a 10 000 t/d producer of lead-zinc-copper-silver ore that has been in operation since 1964. Mining of this multiple lens deposit is primarily by blasthole stoping techniques between 400 m and 1200 m below surface. The combination of a high overall extraction ratio, an overall steeply dipping tabular shape, and high horizontal stresses (twice the vertical) have elevated the induced stress regime to levels comparable to much deeper operations. Improved mine design, and a better understanding of how the rock mass responds to mining in high-stress environments is essential to improve overall recoveries and maintain safety. Seismic monitoring has proven to be an essential tool at Brunswick, for both short-term safety of workers, and long-term strategic planning.Practical case studies illustrate how seismic data, particularly source parameter information, can be used to measure the rockmass response to mining and improve mining layouts in difficult regions. As the global trend continues toward mining in deeper, higher stress environments (e.g., South African Witswatersrand Basin, Sudbury Basin) and as local extraction and thus ground stresses continue to increase in existing deposits, seismic monitoring will play a critical role in mining safely and economically."

Jan 1, 2004

By B. Simser

Noranda?s Brunswick mine is a 10 000 t/d producer of lead-zinc-copper-silver ore that has been in operation since 1964. Mining of this multiple lens deposit is primarily by blasthole stoping techniques between 400 m and 1200 m below surface. The combination of a high overall extraction ratio, an overall steeply dipping tabular shape, and high horizontal stresses (twice the vertical) have elevated the induced stress regime to levels comparable to much deeper operations. Improved mine design, and a better understanding of how the rock mass responds to mining in high-stress environments is essential to improve overall recoveries and maintain safety. Seismic monitoring has proven to be an essential tool at Brunswick, for both short-term safety of workers, and long-term strategic planning. Practical case studies illustrate how seismic data, particularly source parameter information, can be used to measure the rockmass response to mining and improve mining layouts in difficult regions. As the global trend continues toward mining in deeper, higher stress environments (e.g., South African Witswatersrand Basin, Sudbury Basin) and as local extraction and thus ground stresses continue to increase in existing deposits, seismic monitoring will play a critical role in mining safely and economically.

May 1, 2004

By M. Boher, J. Lehmann, M. C. Kaerlé

"In the production of high quality steel, the understanding of the interactions between liquid steel and refractories and of their effect on steel purity and cleanness are becoming more and more important.An experimental study has been per-formed in order to estimate the importance of the reaction between a MgO-based tundish refractory and an Al-killed steel. The results show a pollution of the liquid steel:•the silicon content of the liquid steel increases due to the reduction of the silica of the refractory by the aluminum contained in the steel; and•a reoxidation of the steel occurs and the formation of an oxide layer on the refracto-ry, mainly composed of spinel crystals and of Ca-aluminates is observed.The transfer mechanisms of the various elements are analyzed."

Jan 1, 1997

By Jan E. Nesset

It is just over 100 years since the practice of blowing small bubbles into a mixture of ground ore and water revolutionized the mining industry, resulting in uneconomic deposits becoming highlyprofitable mines, along with the inevitable lawsuits over this new technology called froth flotation. To this day, the viability of many mining projects rests largely with the ability of flotation to effectively capture the valuable minerals and reject wastes. Remarkably, bubble behaviour in flotation has not been well understood until very recently with the advent of new sensor technologies that can be brought directly into the operating plants. This presentation will review the importance to the mining industry of understanding bubbles, highlight these new technologies and illustrate, with examples, how paying attention to your bubbles will pay off.

Jan 1, 2009

By R. E. Hamilton

"The requirements for effective optimization of a mineral dressing operation are discussed, with specific reference to a flotation system . Also considered are the relation-ships between automatic control and optimization pro-grams. Variables are classified into the following groups, and the significance of the classification is discussed: (a) Directly measurable (b) Directly manipulable (c) Uncontrollable (d) Calculable from measurable variables (e) Affected by changes in manipulable or uncontrol-lable variables. New sensors for measuring variables not normally measured are described."

Jan 1, 1967

By R. Bainbridge

"IntroductionTHE LEAD SMELTING Department of The Consolidated Mining •and Smelting Company of Canada, Limited (Cominco), at Trail, B.C. treats materials from numerous sources for the recovery of lead, •and, of secondary importance, for the .recovery of sulphur as S02• The Department's sintering section has a .capacity of 1,500 tons daily. This section is being replaced by •a new charge-•handling and sintering plant with a daily capacity of 2,000 tons of finished sinter. Materials handled in the sintering section comprise concentrates, ores, and fluxes from Company mines and from 'custom' (independent) producers, together with intermediate products from various plants of Cominco'•s Metallurgical Division, all of which must be treated to, make up a chemically balanced charge of a predetermined lead content for the sintering plant.As received, 80 •per .cent of these materials are finer than 200 mesh, and one-quarter of the tonnage (dry basis) is a slurry .at 30 to 40 per cent moisture. This slurry, a -residue from the electrolytic zinc operation, was, for many years, partially dried before being mixed with other dry materials to make up the sinterplant charge.Some experimental work carried out in 1937 indicated that the metallurgy of the sintering operation could be improved by adopting a technique of 'wet-mixing' followed by controlled drying and nodulizing."

Jan 1, 1953

By P. K. Kaiser

3-D virtual reality (VR) visualization has opened new opportunities for complex 3D (x, y, z), 4D (x, y, z, t) or even nD data interpretation. The integration of common earth models (3D geologic data), mine models (3D excavations and stress), extraction models (1D time sequencing or mine sequencing) and nD monitoring data (e.g., seismic event parameters) into a common mining process model provides a platform for experts in various fields to better design, evaluate, monitor and modify mine plans throughout a mine?s life; from feasibility, through operation, to closure. Viewing seismic data in a stereoscopic VR environment within a mining process model offers data interpretation processes previously unavailable at lower dimensionality. MIRARCO has developed data analysis and viewing processes specifically designed to enhance microseismic and seismic data interpretation in a collaborative, immersive VR environment; bringing mine personnel and expert consultants together to evaluate data and make strategic decisions for cost effective and safe mining. Seismic events cause immediate hazards (rockbursts) and microseismicity causes gradual hazards through its cumulative effect in rockmass degradation. The focus of this paper is on understanding seismicity from a mine safety and mine planning perspective; in particular, how seismic migration patterns relate to the rockmass response to mining. The benefits of innovation in seismic data interpretation are significant, e.g., for hazardous work area identification, allowing better formulation of re-entry policies and workforce allocation planning, as well as allocation of effective support systems to strategic areas of elevated risk. Better understanding of the overall response of a mine to extraction also facilitates mine planning and design, assisting in reducing production costs and thus in enhancing profitability.

Apr 1, 2005

"6.1. Mineralogical Techniques ApplicableTo the Platinum-Group Elements6.1.1. IntroductionThe named platinum-group minerals (PGM) usually occur as grains smaller than about 200 microns and, even when present as larger grains as in nuggets, these are often complex multimineral intergrowths. Therefore, the PGM must be examined by microscopic techniques and, because all named PGM are opaque, they are suitable for microscopic study by reflected light. Special techniques for concentrating PGM and preparing suitable polished sections are detailed in Chapter 5. Another characteristic of the PGM is that the majority have very high reflectance at 589 nm, i.e., over 450Jo, but they range from about 38 to 74%. In contrast, micro-indentation hardness has a wider range from - 60 to - 3,000 kg I mm, and the PGM range from brittle to malleable.The small grain-size of PGM imposes certain limitations, or complications, on the usual mineralogical determinative methods of reflectance, micro-indentation hardness and X-ray diffraction. In addition, certain combinations of elements in some PGM render electron-probe analyses difficult. The usefulness and shortcoming of these methods, as applied specifically to the PGM, are discussed in the following sections. These are not, however, meant to be exhaustive descriptions of the techniques, which are fully described in other texts.6.1.2. Micro-Indentation HardnessDetermination of the Vickers Hardness Number (VHN) is discussed in detail in recent publications, such as Bowie and Simpson (1977) and Craig and Vaughan (1981). In addition, the recommendations of the Commission on Ore Microscopy (COM) of the International Mineralogical Association (IMA) are given by Criddle (1980). The usual small grain-size of the PGM, however, precludes the widespread use of this technique and very few PGM have, in fact, had their VHN determined at the COM-recommended standard load of 100 gf (cf. Cabri, 1981b, in Chapter 7). Examination of VHN data reported in the literature reveals that the few PGM whose microindentation hardness has been measured have incomplete VHN data, measured with loads other than 100 gf (Chapter 7). The small grain-size may also result in unreliable VHN data because, even though the correct load may have been applied, a thin grain will give erroneous data due to the matrix, or the grain may even shatter or pop out of the section. On the other hand, micro-indentations may give useful qualitative diagnostic clues. Moncheite, for example, shows fractures near the indentation (Chapter 7, Plate 1). In other cases, intergrown PGM produce different-sized indentations: e.g., froodite-michenerite-gold in Cabri (1972); isoferroplatinumtulameenite in Cabri et al. (1973); michenerite-moncheite in Cabri and Laflamme (1976) and Chapter 7, Plate 1; altaitemichenerite- testibiopalladite in Hudson eta/. (1978) and Plate 1, Chapter 7."

Jan 1, 1979

By Louis Tellier

SIDBEC commenced detailed planning of major capital expenditures to install integrated steelmaking facilities in 1969. Today, less than IO years later, SIDBEC and its subsidiaries have completed major mining, concentrating, pelletizing, direct reduction ? electric furnace steelmaking and continuous casting plants. The total cost of these projects was almost 1 billion dollars. The philosophy behind the project planning and the evolution of management control are explained. These extensive projects were undertaken during a period of exceptional inflation and a disturbed labour climate, but were nevertheless completed with only modest overruns, with good control of timetables and with exceptionally good start-up performance. Project planning, relations with consulting engineers, introduction of new technology, purchasing and field management and cost control are discussed.

Jan 1, 1979

By Stephen L. Chryssoulis

"""Preg-robbing"" of gold by carbonaceous matter during the cyanidation of certain types of carbonaceous gold ores is well documented. Recent studies established that ""preg-robbing"" of gold is not limited to carbonaceous matter. Gold sorbed on the surface of pyrite grains was detected and quantified by TOF-LIMS (Time of Flight Laser Ionization Mass Spectrometry). Crystallites of pyrite from a number of ores from different geological environments have been shown to have gold on their surface apparently sorbed from the ore forming solutions. Surface gold accounts for significant fractions of the gold head assay. Preg-robbing of gold by pyrite from pregnant cyanide solutions was also documented, and accounts for significant losses to tailings. Preventative measures are discussed.1.0 IntroductionThe detection and subsequent quantification of gold sorbed on the surface of pyrite particulates came about during routine determinations of the deportment of gold employing the comprehensive mineralogical approach (Chryssoulis and Cabri, 1990). In some pyritic gold ores it was discovered that the sum of the various forms in which gold ""conventionally"" occurs, was short of the gold assay. The mineralogical procedure used involves the independent determination of each fraction of gold, in other words there is no form of gold which is calculated ""by difference"". The systematic shortfall after having added the forms of gold listed in Table 1 led to the inquiry for the 'missing' gold and its discovery on the surface of pyrite grains, such as crystal facets and fractured surfaces.Preg-robbing of gold by pyrite from pregnant solutions was first described by Lloyd. In his studies, preg-robbing was measured by changes in the solutions/solids gold assays. This paper describes the first application of a direct measurement method for surface gold on pyrite particles from untreated and processed samples, its impact on gold deportment and processing. The advantage of the direct measurement lies in the absence of interference from other forms of gold, leading to more accurate and precise determinations of this unconventional form of gold."

Jan 1, 1997

By R. Nendick

"IntroductionThe Ancient Egyptians recovered gold from the mud in the bottom of ponds by having teams of maidens sit around the pond dipping goose feathers dipped in grease into the mud. The gold would preferentially stick to the oily surface and was periodically washed off to give a gold concentrate. This was a forerunner of today's flotation processes.In Greek mythology Jason and the Argonauts pursued the Golden Fleece, which was a primitive form of gravity concentrate produced when gold ore slurry was passed over a sheeps fleece. The heavy gold settled and was caught in the fleece, producing a rich concentrate that allowed Jason & Company to perform the first recorded case of highgrading. The process was a forerunner of todays shuiceboxes used in placer mining.From these simple beginnings, gold metallurgy has progressed to a state where very complex flowsheets are proposed, sometimes to perform a simple metallurgical task. Figure (i) shows a hypothetical flowsheet to identify the range of unit processes that might be brought to bear on a refractory ore. The flowsheet identifies the three primary areas of gold metallurgical operations:Ore PreparationExtractionRecovery."

Jan 1, 1986

By O. Babak, J. G. Manchuk

ABSTRACT A significant factor in evaluating bitumen recovery from an oil sands mine is the particle size distribution (PSD). Increased understanding of mined ore quality and improvement in predictions of recovery can be achieved through PSD modeling. This paper addresses PSD modeling using geostatistics. PSDs may be described using many discrete particle sizes, making this a challenge. The approach parameterizes PSDs with a few statistics. A lookup table is used to reconstruct the PSDs based on models of the statistics. The workflow is applied to Total E&P Canada’s Joslyn Lease and yields good results that reproduce input statistics without introducing artifacts.

Jan 1, 2013

By Mahmoud Ahmed

Three-dimensional models are in increasing demand for design, maintenance, operations and construction project management. Point-clouds are the main output of automatic data collection using laser-scanners and photogrammetric technologies. Pipe-works may comprise 50% of the value of important construction projects such as industrial and research facilities. We have developed a practical and cost-effective approach, based on the Hough-transform and judicious use of domain constraints, to find, recognize and reconstruct/model 3D pipes within point-clouds fully automatically. The developed approach allows pipe growing within a 3D point-cloud. It samples the point-cloud to sequential orthogonal slices, detects pipe?s cross-sections within sampled slices and grows the pipe along the cross sections centerlines. It is validated using laser-scanner data from construction of the Engineering-VI building on the University of Waterloo (UW) campus. The system works on a typical laptop. Recognition and localization results are within a few millimeters. The presented approach opens the gate to broad applications of pipe-network modeling.

Aug 1, 2013

By L. Kong, V. G. Papangelakis, L. Li

"The Eh-pH diagram of lithium-titanium-water system at 25°C, 100 °C and 200 °C was constructed. It shows that there exist thermodynamic stability areas of Li2TiO3. This indicates a thermodynamic possibility for the formation of Li2TiO3 in aqueous solution. A hydrothermal process has been applied for the preparation of Li2TiO3 using TiCl4 and LiOH•H2O as raw materials. The prepared samples were examined with X-ray diffraction, scanning electron microscopy and thermo-gravimetric analysis and differential scanning calorimetry. The results show that temperature and washing condition have significant effects on the phase composition of the product. Phase-pure Li2TiO3 powders were obtained at 200°C with Li:Ti molar ratio of 2.0.INTRODUCTIONLithium-containing ceramics enriched in 6Li, such as Li2O, LiAlO2, Li4SiO4, Li2ZrO3 and Li2TiO3, are considered as tritium breeding materials (Saito et al., 1998; Roux et al., 1998; Johnson et al., 1998; Hoshino et al., 2002). In view of its admirable properties: low-activation, good thermal stability and thermal conductivity, excellent tritium release performance and reasonable lithium atom density (Kopasz et al., 1994; Roux et al., 1996; Saito et al., 1998; Wu et al., 2008), Li2TiO3 is recognized as one of the most promising candidates of tritium breeding materials. Meanwhile, Li2TiO3, as the precursor of H2TiO3-type lithium absorbent, receives more attention as the development of extracting lithium from salt lakes (Zhong, 2004; Zhang, 2010).Several synthetic techniques have been applied to prepare Li2TiO3 powders, such as solid-state methods (Lulewicz and Roux, 2002; Ramaraghavulu et al., 2011; Mandal et al., 2012), sol-gel processes (Deptula et al., 2002; Lee, 2008) and solution combustion routes (Cruz et al., 2006; Jung et al., 2006; Sinha et al., 2010). A solid-state method may produce a series of problems, including impurity contamination and difficulty in morphology control of the obtained powders, although the process involved is simple. The solgel process is prolonged and usually demands for multi-step reactions, while solution combustion route requires plenty of energy and easily causes product contamination by the fuel used. Owing to its environmentally benign and highly suitable characteristics in fabricating materials, hydrothermal technology has been widely used and became a powerful tool in the field of material synthesis (Yoshimura and Byrappa, 2008). For example, ZnO in the form of bulk single crystals, fine particles and thin films, which is an attractive photoelectric material, was successfully synthesized by hydrothermal process (Sekiguchi et al., 2000; Ohshima et al., 2004). A hydrothermal technique was also used to the preparation of carbon nanotube, which possesses outstanding mechanical, structural and electric properties (Bernholc et al., 1997), and is superior to the commonly used method (Gogotsi and Libera, 2000). There, it provides an option for preparing Li2TiO3. Laumann et al. (Laumann et al., 2010) synthesized cubic a-Li2TiO3 by hydrothermal reaction at 180 °C for 18 h, using TiO2 powder, comprising of anatase and rutile, and lithium hydroxide in de-ionized water. However, the prepared a-Li2TiO3 is extremely unstable with a maximum lithium loss of 75% when treated in bathing experiment."

Jan 1, 2012

By E. W. Mountjoy

THE Exshaw formation is a thin but very persistent black shale unit generally well exposed along the easterly scarp faces of the fault blocks comprising tl1e front ranges of the Rocky mountains. It is over lain by the Mississippian Banff shales and silty shales and underlain by the massive Palliser Limestone formation of late Devonian age. The Exshaw continues eastward under the plains of Alberta and on into Saskatchewan, with little change until it reaches the surface of the Palaeozoic-Mesozoic unconformity. During the summer of 1953, the writer was working- with a field party under Dr. J. L. Usher in the front ranges of the Alberta Rocky mountains. This party, sent out by the Mobiloil Company, conducted a geological survey of Devonian rocks between the towns of Banff and Jasper. The writer helped to describe and map these Devonian rocks and obtained first-hand information concerning the Exshaw shale and its relationship to the underlying and overlying sediments. Additional information was obtained from reference material and from a number of geologists whom the writer has consulted. Grateful acknowledgment is offered to them, to the Mobiloil Company for releasing field information, and to F. W. Beales and W. P. Hancock who helped edit the original paper for publication. Information from areas north and smith of that studied and from bore holes on the prairies is referred to. Localities mentioned may be found in Figure 1.

Jan 1, 1956

"The most widely used method for predicting the onset of continuous caving is Laubscher’s caving chart. A detailed examination of this method was undertaken which concluded that it had limitations which may impact on results, particularly when dealing with stronger rock masses that are outside current experience. These limitations relate to inadequate guidelines for adjustment factors to rock mass rating (RMR), concerns about the position on the chart of critical case history data, undocumented changes to the method and an inadequate number of data points to be confident of stability boundaries.A review was undertaken on the application and reliability of a numerical method of assessing cavability. The review highlighted a number of issues, which at this stage, make numerical continuum methods problematic for predicting cavability. This is in particular reference to sensitivity to input parameters that are difficult to determine accurately and mesh dependency.An extended version of the Mathews method for open stope design was developed as an alternative method of predicting the onset of continuous caving. A number of caving case histories were collected and analyzed and a caving boundary delineated statistically on the Mathews stability graph. The definition of the caving boundary was aided by the existence of a large and wide-ranging stability database from non-caving mines. A caving rate model was extrapolated from the extended Mathews stability graph but could only be partially validated due to a lack of reliable data."

Jan 1, 2003