Search Documents

By A. David MacPhail

"Highland Valley Copper is a large volume producer of copper and molybdenum concentrates. Production is by conventional truck and shovel operation combined with an extensive ore handling in-pit crushing and conveying system.Grade of the two orebodies is low at 0.4% copper and 0.007% molybdenum and this demands a production rate in excess of 260 000 tpd at a stripping ratio of 1: 1. Mining cost has to be kept at minimum levels to keep the mine profitable and thus, it is necessary to keep in the forefront: of technology. As well as the in-pit crushing system, the mine has pioneered the use of shovel weighing coupled with a state-of-the-art dispatch system.Maintenance of the equipment is carried out at the on-site mine maintenance shop with assistance from local shops for engine and wheel motor rebuilds and other large jobs such as those requiring stress relieving. Shovel and truck rebuilds are undertaken by mine crews. Both long- and short-term planning is designed and scheduled in the mine engineering section. Outside consultants are used to assist in slope design, reclamation and blasting technology."

Jan 1, 1992

By J. T. Furey

"A pilot plant study was conducted to evaluate the performance of column flotation in the recovery of gold from a gold/tellurides bearing sulphide ore, and to compare the performance of column flotation to conventional ""mechanically agitated"" flotation.Tests were conducted in a 60 liter glass column with ground flotation feed split from a concurrently operating conventional pilot plant, thus permitting direct comparison between the two processes. During the test program, the effects of wash water rate, gas holdup, froth depth, residence time and flow bias were examined in detail.The ore had an average ""as tested"" feed grade of about 5 g/t gold and 1 % sulphur, with the gold occurring primarily as inclusions of montbragite (Au2Te3) in pyrite, with minor amounts of native gold. Conventional flotation using 60 minutes residence time across four roughing stages recovered about 97% of the gold into concentrates grading about 50 g/t Au. A single stage of column flotation roughing using 25 minutes residence time matched the conventional circuit recovery of 97%, but produced grades of+ 150 g/t Au. INTRODUCTIONColumn flotation is the most significant innovation that has occurred in the mineral processing industry in recent years and has become an important alternative to mechanical flotation. Column flotation has been most widely accepted and applied in cleaning service where it has frequently proven to be superior to mechanically agitated flotation. Roughing in columns has not been ignored, but early testing indicated that columns may not be capable of achieving adequate recovery and, to date, columns have not been seen as serious competitors for mechanical roughers."

Jan 1, 1990

Why Innovate in Mining? ?Obvious, right? ?Increase productivity and profitability ?Improve safety and ergonomics ?Improve our environmental record and eliminate liabilities ?Implement process control methodology ?Introduce information systems technology to gain control ?Low hanging fruit ?Reference ?Heather Ednie, Innovation CIM Magazine Feb. 2006 ?Peck & Skinner, Getting better bang for your buck with technology

May 1, 2006

By Marc C. Bétournay

A number of successful proof-of-concept projects have been carried out to replace conventional power application, such as diesel and rechargeable batteries, in underground mine vehicles. This has led to the development of the world?s first fuelcell production vehicle, a mine locomotive. A mine loader project has also started and several other projects are planned. These projects are providing the mining industry with the required information to make this technology shift possible. The application of fuelcell power will yield several important benefits such as the elimination of underground diesel emissions, significant reduction in the primary extraction?s sector greenhouse gas emissions and support for a more productive scenario. This article reviews these successes, discusses ongoing and potential projects and presents the technology application benefits that could be possible for mining operations.

May 1, 2003

By Roger Lacroix

L?arrivée de nouvelles technologies sur le marché des foreuses portables combinée au besoin des mines à mieux consommer l?énergie électrique ont permis d?identifier le potentiel de deux nouveaux type de foreuses présentement utilisées en Afrique du Sud, à savoir les foreuses électriques et les foreuses hydrauliques actionnées à l?eau. Grâce à la collaboration de mines Niobec et Géant Dormant de Cambior Inc., ainsi que d?Hydro-Québec, le potentiel réel d?économie énergétique des foreuses portables hydrauliques et électriques par rapport aux foreuses conventionnelles à air comprimé a été évalué pour des roches dures et moles. Ainsi, cet article a pour objectif d faire ressortir ces potentiels d?économie énergétiques. En outre, les résultats pour une mine mécanisée et une autre mine de type filonien, dans lesquelles on retrouve des conditions de terrain différentes, seront présentés. Les résultats montrent un potentiel d?économie énergétique d?environ 70% pour la foreuse électrique et d?environ 50% pour la foreuse actionnée à l?eau. Ces résultats montrent qu?il est possible d?obtenir une meilleure efficacité énergétique par mètre foré. Ainsi, il apparaît maintenant intéressant de poursuivre les travaux de développement des deux technologies pour les applications de forage vertical et de tensionnement des boulons, et de viser à accroitre le taux de pénétration de la foreuse électrique pour le rendre équivalent à celui de la foreuse à air comprimé.

May 1, 2007

By William M. Luff

This paper outlines the regional geology and history of the area, and summarizes the stratigraphy, structure and geology of the Brunswick No. 12 mine area. The Brunswick No. 12 deposit is a stratiform massive sulphide body. It occurs in rocks of the Tetagouche Group, which is believed to range in age from Lower to Middle Ordovician. The stratigraphic sequence, including the stratiform orebody, in ascending order consists of older metasedimentary rocks, augen schist, metasediments, augen. schist, footwall metasediments, the -massive sulphide body, iron formation, hanging-wall metasediments, siliceous tuff, basic volcanic rocks , basic iron formation and a porphyry dyke. This sequence is similar to that at some other deposits in the area. Four phases of structural deformation are known to be present in the Brunswick No. 12 mine area. The first deformation folds (F1 ) and associated faulting are the most important factors in determining the distribution of the massive sulphides. This deformation has resulted in the massive sulphides being separated into four zones: the Main Zone, the West Zone, the East Zone and the V-2 Zone. Brunswick Mining and Smelting Corporation Limited is actively mining, developing and exploring the deposit.

Jan 1, 1977

By J. B. Morrow

Methods of Coal Preparation Fundamentally, the object of coal preparation is to increase, economically, the value of a fuel by making it more suitable to the uses of the consumer. This can be accomplished in three major ways: 1.Screening or sizing 2.-Mixrng or blending 3.-Cleaning By combinations of any or all of these methods we can prepare coal to meet standard specifications-a process of standardization which is the more desirable the more nearly it approaches the unvarying quality of packaged goods, where the package you buy today and tomorrow is the same as that you bought yesterday. It should be noted that it is readily possible to get good cleaning and still have poor preparation because of faulty screening and mixing, and, on the other hand, it is possible to get a passable grade of cleaning, combined with good screening and mixing facilities.

Jan 1, 1931

By D. M. Morrison

"The most important factor in Canadian mining is not the operating cost of current projects but the availability of capital for future projects. The future of mining at depth will be producing ore from the top of the orebody working downward with very effective, tightly controlled mining methods, i.e. either selective mining or bulk mining with well controlled dilution and fragmentation. The key characteristics of future mines will be smaller access excavations, more effective ground support, very precise blasting techniques and more efficient and reliable materials handling systems. Equipment will be smaller and designed for high efficiency and low maintenance, reducing both the capital and operating cost. This means there will be fewer scoops, more continuous mucking machines and conveyor belts, both lateral and vertical.Orepass failures have become accepted and the resultant redevelopment and retramming has become common. The capital investment in so-called permanent ore passes and crusher stations becomes questionable, particularly when crushers are only necessary for less than 10% of the ore going through the system. The best way to solve the chronic instability of ore passes is, as with all of the stability problems at depth, by reducing the excavation size rather than increasing ground support. Smaller access drifts would reduce the capital cost and increase the rate of development as well as reduce the amount of waste to be handled, reducing the ground support and the ventilation requirements. Large drifts and ore passes are essential only for the equipment needed to handle large pieces of ore and the productivity of scoops is very expensive when the requirements for ventilation and large access drifts are taken into account. The key issue is the fragmentation generated by primary blasting.The future of mining in Canada will depend on simple and robust technology geared to the environment in which it will have to operate. Its survival will depend on some-thing much more fundamental and difficult to accomplish than a technological advance — it will require a dramatic change in the way the mining process is managed, how work is organized, how effort is rewarded and how costs are measured — a complete change in mind-set."

Jan 1, 1996

By William D. Macdonald

The Upper Devonian Kettle Point black shale of southern Ontario is poorly exposed. Structural maps pre-pared from the data of numerous wells show that the upper surface of the formation has low regular relief, and that the lower surface reflects domes in the Middle Devonian and also local subsidence of the Devonian rocks due to solution of salt in the Silurian Salina Formation. The appearance of minor amounts. of marcasite, pyrite, and calcite, m that order, as interpreted from the evidence of concretions from the type locality at Kettle Point is thought to have been influenced by a rise m the pH within anaerobic sediments preceding compaction.

Jan 1, 1960

By B. T. Lu

The corrosion and wear properties of a series of chrome white iron (CWI) castings were study using electrochemical and low-stress sliding abrasion tests. The results confirm that the corrosion resistance of these materials is largely dependant on the quantity of chromium in the matrix, while the wear resistance is mainly controlled by the volume fraction of chromium carbides. A pseudo-wear/corrosion map is developed to identify alloy compositions that may be suited for erosion/corrosion conditions.

Jan 1, 2005

By A. Griffiths, G. Vickell

"INTRODUCTIONA successful cyanide destruction process has to ensure environmental compliance at reasonable cost. That this is possible with hydrogen peroxide is shown by the fact that over twenty gold mines either already use H2O2 or intend to start using it within the next few months. About half of these mines are in Canada.This growth is remarkable, considering that the first treatment plant to use H2O2 for detoxifying cyanide was commissioned less than five years ago at Ok Tedi, in Papua New Guinea.Hydrogen peroxide is being applied to a wide range of situations, including:Treatment of CIP pulps; examples: Ok Tedi, PNG; Hope Brook, Nfld.Treatment of barren bleeds and filtrates; examples: Nickel Plate, B.C.; Puffy Lake, Man.Treatment of tailings pond discharge; examples: Detour Lake, Ont., Page Williams, Ont.Treatment of excess heap leach solution; examples: Hope Brook, Nfld; Gordex, NS.Treatment of barren heaps after heap leaching; examples: Alhambra, NV; Wharf Resources, S.D.Treatment of pond reclaim water to prevent either ""preg-robbing"" or depression of gold-bearing pyrite in a flotation step; example: Getchell, NV.Treatment of backfill to prevent possible groundwater contamination; example Hope Brook, Nfld.Treatment of tailings ponds to prevent bird kills; example: Paradise Peak, NV.""Emergency"" units to deal with unusual events such as freak storms or dam failures."

Jan 1, 1989

By D. R. Lentz, C. J. Beaumont-Smith, S. H. Mcclenaghan

"Abstract - The Louvicourt Au-Ag-Cu-Zn-Pb sulfide deposit is hosted by a Middle Ordovician calc-alkaline sequence of aphyric rhyolite flows and associated fragmental rocks at the top of the Flat Landing Brook Formation. The Zr/TiO2 (average = 0.110) and Y/TiO2 (average = 0.021) ratios in the footwall felsic volcanic rocks are consistent with known values for the Reids Brook member. The deposit consists of two concordant lenses of semi-massive to massive sulfides, approximately 150 m long and up to 9 m thick, which represent a fold repetition of a single exhalative horizon. The deposit contains a geologic resource of 136 000 tonnes grading 1.2% Pb, 1.0% Zn, 0.4% Cu, 90.9 g/t Ag, and 0.96 g/t Au; the deposit locally contains elevated Au (2.9 ppm) and Ag (320 ppm) contents. A laterally continuous iron formation that contains barite caps the deposit, and is gradational vertically and laterally into laminated siltstone. The exhalite confirms the stratiform nature of this deposit, but a large percentage of sulfides occur as late replacements of altered felsic fragmental rocks in the footwall. Abundant examples of colloform pyrite and perlitic and spherulitic textures in volcanic clasts are well preserved. The base- and precious-metal content of the Louvicourt deposit is atypical of the Bathurst Mining Camp (BMC). Reported assay data (n = 27) indicate an average Pb/Zn ratio of 2.6, the highest in the BMC (average = 0.39). Lead exhibits a strong Spearman Rank correlation (r' = 0.92) with base metals throughout the sequence, indicating a preponderance of galena in both the stockwork and stratiform zones. The Ag and Au contents in this deposit are among the highest in the BMC and exhibit a Au-Ag- Cu-Pb association. Barite-rich exhalative pyrite exhibits a moderate Au correlation with Ag (r' = 0.77; n = 10) and Cu (r' = 0.76) and occurs in portions of the exhalative sulfides that are enriched in Pb. Chemical exhalative rocks are conformably overlain by trachy-andesitic volcaniclastic (possibly pyroclastic) rocks that are assigned to the Little River Formation. These are enriched in Nb (average = 38.4 ppm) and P2O5 (average = 0.17 wt.%), and have much lower Zr/TiO2 (average = 0.056) and Y/TiO2 (average = 0.0062) relative to rocks higher in the hanging wall. The intermediate volcanic rocks are conformably overlain by massive to pillowed basalt flows and related hyaloclastite that have Nb/Y = 0.60 and high TiO2 contents (average = 2.8 wt.%). This chemistry is consistent with rocks of the Brunswick Mines member (Little River Formation), except that these rocks are considerably enriched in P2O5 (average = 0.82 wt.%). This syngenetic exhalative deposit is unique for the BMC with a high Pb/Zn and elevated Au and Ag contents, as well as an epithermal signature (Sb-Ag-Au-Tl-Hg), analogous to high sulfidation volcanogenic massive sulfide deposits. Its intimate relationship with an emergent felsic dome (Flat Landing Brook Formation), chlorite-silicate-oxide-sulfide exhalite (locally hematitic), and the abundance of barite are classical features of many of the Kuroko deposits."

Jan 1, 2006

By W. E. Lockley

This paper will attempt to answer a number of questions which are important to the safe and continued operation of an electric power system. 1. WHY should electrical protective devices be tested? 2. WHAT devices should be tested ? 3. WHEN should they be tested ? 4. HOW should they be tested? 5. WHO should test them ?

Jan 1, 1977

By George S. Rice

Foreword Explosion hazards differ widely in the mines of different fields or coal basins. They also differ as between different mines in the same basin or fold, because of variations in gas entering the mines, and because dust conditions and explosion hazards are affected by the mining methods employed and the organization of the work. It is unquestionably true, however, that there are greater differences in explosion hazards in mines of different coal fields or basins than between different mines of the same field or basin. In these respects, the coal fields and individual mines in Alberta are not exceptional. The same conditions obtain in various countries where coal is mined, and are found in single States, as for example in Colorado, where coals are mined ranging in character from sub-bituminous to anthracite, and in attitude from flat horizontal to steeply pitching beds. The U.S. Bureau of Mines, at its experimental mine near Pittsburgh, Pa., has made large-scale tests of the relative explosibility of dusts of coals, ranging in rank from Wyoming sub-bituminous coal containing 19 per cent moisture, to anthracite from Pennsylvania, and including samples from a mine in the Crowsnest Pass district, B.C., and from a Vancouver Island mine. The Bureau has also made similar tests of the dust of coal from a Yorkshire mine which the British Safety-in-Mines Research Board uses as standard.

Jan 1, 1927

By P. E. Mather, M. J. M. Krane

Uncertainty quantification is a means of articulating the reliability of model estimations. Models of copper pyrometallurgical processes have been published for decades but discussion of their reliability has typically been terse and qualitative, mitigating understanding of their exact applicability to industrial situations. This presentation shows basic uncertainty propagation and Bayesian model calibration, two powerful uncertainty quantification tools, applied to a reduced order model of copper fire/anode refining. The implications of the uncertainty quantification analyses on the applicability of the model results to industrial practice are then discussed. Finally, other possible applications of uncertainty quantification to copper extractive metallurgy are explored. INTRODUCTION Modern copper production operations, including mining operations through wire drawing factories, are ubiquitously heavily instrumented. Most mine-sites and smelters have large repositories of historical data. That said, much of this data is not exploited to its maximum effect. This proceeding provides examples of using uncertainty quantification (UQ) to maximize the informational yield of the data collected from a fire-refining operation. Anode/Fire Refining is the final pyrometallurgical step in the production of copper anodes; it is an essential and universally employed processing step at smelters (Schlesinger, King, Sole, & Davenport, 2011). Much like the smelting and converting furnaces further up the process stream, anode furnaces are difficult to instrument due to their high temperature and the corrosive and/or caking quality of their offgas. This makes continuous and accurate measurement of the streams leaving the unit operation, e.g. liquid copper, slag, and offgas very difficult. As an example, offgas flowmeters, while providing continuous draft values, could miss the actual draft value by tens of percent due to caking or corrosion. UQ methods account for the uncertainty in process measurements and parameter values; they use a process model with measurements of performance indices to provide better and better estimations of process performance. This proceeding will first introduce a surrogate model for copper fire refining, made from a 1D, transient, reacting flow model of the process presented elsewhere in these proceedings (Mather & Krane, 2019). Discussion of the data used to make the surrogate model, as well as the creation of the surrogate model, will be included. Then, a Monte Carlo simulation will be performed, showing the expected soot production rate based on the surrogate model and assumptions about the uncertainty in the model’s parameters. Finally, the surrogate model parameters will be calibrated in a Bayesian way; this will tell what the actual uncertainty in the parameters are, given a set of observed industrial data and prior assumptions of the observations’ and parameters’ uncertainty.

Jan 1, 2019

By Tom Olsen, Tom Ohrling, Peter Taggart, Chris Martin

"North American Palladium commissioned the new concentrator at the Lac des Iles mine in the summer of 2001. The 15,000 tonnes per day mill replaced the existing 2,400 tonnes per day facility, as part of a major mine expansion.At Lac des Iles, the grain size distribution of the platinum group minerals (PGM) is bi-modal. Roughly two-thirds of the PGM are relatively coarse-grained, and often associated with fast floating copper and nickel sulphides. The remainder is ultra-fine, and locked in silicates, which poses a special challenge to the metallurgist. The previous mill typically recovered just the fast-floating mineralisation, but to achieve target recoveries, the new mill has to recover a substantial amount of the ultra-fine PGM. The metallurgical challenges associated with the recovery of fine-grained PGM in the talcous Lac des Iles ores, are described.The paper describes the approach used in circuit optimisation, and how metallurgical and operational optimisation raised palladium recoveries by more than 6% in six months, by tuning the circuit to recover some of the ultra-fine PGM mineralisation.BACKGROUNDThe Lac des Iles mine, owned and operated by North American Palladium Limited, is located about 115 kilometres north of Thunder Bay, Ontario. The mine originally opened in December 1993, and prior to 2001 included a mill capable of handling 2,400 tonnes per day of ore delivered from the nearby Roby pit.Following an intensive exploration programme conducted in 1999, and a detailed feasibility study, conducted in 2000, North American Palladium initiated a mine expansion project, the objective being to expand milling throughput from 2,400 tonnes per day to 15,000 tonnes per day. This required construction of an entirely new mill, which was commissioned in May 2001."

Jan 1, 2003

By Robin Phinney

Certain statements in this presentation may constitute "forward-looking" statements which involve known and unknown risks, uncertainties and other factors which may cause the actual results, pe1formance or achievements of the Corporation, or industry results, to be materially different from any future results, performance or achievements expressed or implied by such forward-looking statements. When used in this presentation, such statements use such words as "may", "would", "could", "will", "intend", "expect", "believe", "plan", "anticipate", "estimate" and other similar terminology. These statements reflect the Corporation's current expectations regarding future events and operating performance and speak only as of the date of this presentation. Forward-looking statements involve significant risks and uncertainties, should not be read as guarantees of future performance or results, and will not necessa1ily be accurate indications of whether or not such results will be achieved. A number of factors could cause actual results to differ materially from the results discussed in the forward looking statements including, but not limited to, the factors discussed in the Corporation's annual information form filed on March 9, 2011. Actual results could differ materially from those currently anticipated due to a number of factors and risks. These include, but are not limited to, the failure to obtain necessary regulatory approvals, including environmental approval, the failure to secure full project financing, the failure to implement the recommendations set out in the Technical Report, the failure to raise financing to implement the recommendations in the Technical Report, risks associated with the mining industry in general (e.g., operational risks in development, exploration and production; delays or changes in plans with respect to exploration or development projects or capital expenditures; the uncertainty of estimates and projections relating to production, reserves and resources, costs and expenses; and health, safety and environmental risks), decrease in potash prices and exchange rate fluctuations. Although the forward-looking statements contained in this presentation are based upon what management of the Corporation believes are reasonable assumptions, the Corporation cannot assure shareholders that actual results will be consistent with these fonvard-looking statements. These fon\?ard-looking statements are made as of the date of this presentation and are expressly qualified in their entirety by this cautionary statement. Subject to applicable securities laws, the Corporation assumes no obligation to update or revise them to reflect new events or circumstances. This presentation is a market update based on the Corporation's public disclosure and does not form a part of any offer of securities, or constitute a solicitation of any offer to purchase or subscribe for securities. Any purchase of securities in the company should be made solely on the basis of information contained in the Corporation's public record which is available on www.sedar.com .

May 1, 2013

By H. Kalsi

"IntroductionRoyal Oak Mines Inc. is currently operating the Parnour No.1 mine located 10.5 miles east of Tinunins, adjacent to Highway No. 101. The operation produces gold ore at a rate of 3300 tpd. A variety of mining methods including bulk open stopes with ITH drilling, narrow vein panel, longhole and open pits contribute to produce 1.2 rnillion ore tons annually. The milling process requires water at an average rate of 1 rnillion gallons per day (700 U.S. gpm). The Pamour No.1 mine has historically had two major problems with regard to water control. The flfSt is the underground pumping system's inability to handle excess inflows of water generated from spring thaws. When the thaw takes place over a short period of time, large inflows of water are created which quickly migrate underground and sometimes result in the loss of the lower loading pocket. During the spring runoff the pumps at Parnour No.1 work continuously for 24 hours at a rate of 1200 U.S. gpm. The system was further taxed in 1991 when the Hoyle mine was connected to the Parnour No. 1 mine and whatever excess capacity the pumping system had for the spring runoff was taken up handling the inflow of mine water generated by the Hoyle.The second problem facing the mine was the lack of water for the mill during the severe cold winter months and dry summer months. At those periods inflows of water into the mine decline and the underground water normally pumped to the mill is severely decreased. In times of dry spells mill personnel increase the water diversion from the Three Nations Lake in order to meet water demands and maintain tonnage throughout. In essence, the mine was going through an annual ""feast or famine"" situation and a solution was needed.A number of options were considered but were narrowed down to the two most practical. The first was to modify the existing pumping system and increase its capacity in order to handle the excessive runoff during spring thaw. This involved a heavy capital expenditure and would have caused additional operating costs (i.e. increased hydro). The option chosen by the management was to divert the spring runoff into an unused section of the mine called The West End. A bulkhead placed at the 2400 level would provide an ultimate underground water storage potential of 150 million gallons. This would also cut down the load on the existing pumping system, save electric consumption in pumping and provide water storage which could be used for milling during the two dry spells. Pumping stored water from the mine could be scheduled for off peak hours to take advantage of lower power rates. To meet these objectives an underground bulkhead capable of withstanding high water pressure up to 2000 ft head (866 psi) was constructed in the spring of 1992. The bulkhead site was at the 2400 level at the Pamour No.1 mine. A major consideration was the requirement to construct a safe bulkhead and to minimize water leakage from the bulkhead.Figure 1 shows the bulkhead location."

Jan 1, 1994

By W. G. McBride

The mining industry has already become highly technical in all its branches and this has brought about specialization in mining engineering. Increasing demand for mineral products, exhaustion of high-grade or easily worked deposits, and narrowing of the fields for exploration and development, are forcing mines to greater depth and to working material of lower grade and more complex composition. The Robinson Deep at its Turf shaft has reached a depth of 7,640 feet and expects to go to 8,500 feet; Miami Copper, under normal market conditions, profitably mines ore running only 16 pounds of copper to the ton; Alaska Juneau is making a profit on ore running about $1.15 per ton in gold; and many mines are handling ores of an extremely complex nature. In each case, the success of these operations has depended upon the application of sound scientific principles and good business methods to the problems involved. It may be safely assumed that mining at great depth and the exploitation of low-grade, or complex, ores will become more and more important as time goes on, and this means that greater and greater demands will be made upon the technical skill and business ability of the mining engineer. To meet this condition, the more or less haphazard methods of training the young engineer that have prevailed in the past will have to be replaced by a careful and well-ordered system of engineer-training. Upon the industry and the older mining engineer falls the duty of providing means to assist the deserving student to prepare himself properly to meet the increased demands that are falling upon his profession. Consideration of the training of the mining engineer involves a decision as to what constitutes his field of usefulness. Technical control of methods and processes obviously falls upon the engineer, but there are still many who doubt his usefulness in the executive field, particularly in positions involving close contact with the men and work. Many engineers have failed as shift-boss or foreman, but this has been generally due to fault in the management in using men who were temperamentally unfit to lead others or who lacked the necessary preliminary training.

Jan 1, 1932

By T. C. WEBB

In New Brunswick, significant potash deposits are intimately associated with rocks of the Lower Carboniferous Windsor Group. To date, two deposits high in sylvinite, up to 20 m thick, have been confirmed at depths between 490 and 1,035 m below surface near Plumweseep and Salt Springs. These areas are currently under development by the Potash Company of America and the Denison-Potacan Potash Company respectively. A third area, near Lower Millstream, is also known to contain potash-bearing evaporites and is now being explored by BP Exploration Canada Ltd. All three areas are situated in the western half of the Moncion Subbasin and are within 25 km of Sussex. Numerous similarities in stratigraphy, thickness, mineralogy and structure suggest that deposition of evaporites throughout much of southern New Brunswick was contemporaneous and extended over a considerable area. Future opportunities for potash exploration in the province thus seem excellent. A number of large unexplored areas remain in the Moncion and Cumberland Subbasins and in parts

Jan 1, 1984