Search Documents

By W. J. Pearson

"""POTASH"" is a term applied to the compounds of the element potassium (K) and when used in agriculture and industry is ex-pressed in terms of potassium oxide (K2O), regardless of the actual com-position of the compound. When a chemical analysis is made of a fertilizer, the amount of K is deter-mined and then calculated to the equivalent amount of K2O. However, the compound K2O does not exist in nature. Most of the world's potash supply is derived from mineral deposits similar to those in Saskatchewan and New Mexico. However, there is some production from concentrated surface brines such as occur in Searles Lake, California; Salduro Marsh, Utah; the Dead Sea; and from well brines in Micl1igan."

Jan 1, 1960

By M. M. Williams

ALBERTA has been generously endowed with oil, natural gas, coal and water power, thus giving power producers a wide choice in the type of plant and fuel which can be used. Therefore, with such a variety of energy sources to choose from, why was coal selected as the primary fuel at Calgary Power's Wabamun steam plant? This part of the paper will cover the circumstances that led the Company to decide in favour of coal. The second part, to be presented by C. F. Doerr, will describe how the Wabamun coal mine has been developed to supply the large fuel requirements of the power plant. Before considering the Wabamun plant, we require a general under-standing of? the Company's electric system and load. Power is fed into a 5,100-mile high-voltage transmission grid from eleven hydroelectric plants and from the Wabamun steam electric plant. These plants have a combined generating capacity of 820,000 horse-power. Of this total, the hydro

Jan 1, 1963

By J. E. Nesset, W. Zhang, J. A. Finch

Frother influences water recovery through control of bubble size and a chemical effect. De-coupling the two is necessary to establish the extent of the chemistry effect. A setup is described to give steady state water overflow rate (Jwo) along with measurements of bubble size into and on top of the froth. Arguing neither bubble size correlates directly with water overflow, a frother mass balance is solved to estimate the bubble surface area flux in the overflow (Sb0 ). The solution required measurement of frother concentration using TOC analysis and frother adsorption density using surface tension data. The relationship between Jwo and Sbo reveals the frother chemistry effect, quantified for discussion purposes by an equivalent water layer thickness.

Jan 1, 2009

By H. C. Cooke

Those who have followed the geological developments in connection with the copper deposits of Quebec will recall that on many properties the sulphide bodies occur as replacements of fault breccias or tuff breccias, and exhibit a pronounced distaste for the more massive lavas. At the same time the rocks around the ore-bodies are profundly altered, first by addition of silica and sericite, later by conversion of these minerals into chlorite. It has been known for some years that at the Amulet and Waite-Ackerman Montgomery mines these conditions do not prevail. At both mines the ore-bodies are replacements of massive lavas, and at the Amulet they are associated with a very peculiar rock christened ?spotted dog', or 'dalmatianite'. Accordingly, when in 1929 the writer had the opportunity to make a further examination of these properties, two problems presented themselves for solution. The first was to determine, if possible, the conditions under which massive lava, rather than breccia, is replaced by the sulphide masses; the second, to find out the exact nature of dalmatianite and its relations to the sulphide bodies. The first of these problems is believed to have been solved; the second has been found very complex, and will require further work before it is satisfactorily settled.

Jan 1, 1930

By R. C. Tait

The gold at Giant Yellowknife is intimately associated with a complex mixture of sulphides, including pyrite, arsenopyrite, stibnite, and a wide variety of antimony sulpho-salts. Direct cyanidation has never been feasible. Recovery is almost entirely dependent upon flotation, roasting of flotation concentrate, and cyanidation of calcine. In November 1958, an Edwards-type roaster and an early prototype, two stage Fluosolids roaster, were replaced by a large two-stage Fluosolids roaster of improved design. The new roaster was started at "safe" medium temperatures, but early in 1959, temperatures in both stages were gradually and deliberately lowered to determine whether continuous autogenous roasting could be maintained under exacting low temperature conditions necessary for good extraction. Operation is smooth and continuous with first and second stage temperatures controlled at 925° and 875°F respectively. Plant cyanide ex-traction compares very favourably with extraction from low

Jan 1, 1961

By C. R. Edwards

"Equity Silver Mines Limited, Canada's largest silver mine, has designed, built and operated a leach plant to reduce the levels of antimony and arsenic in its silver-gold-copper flotation concentrate. The orebody contained deleterious antimony and arsenic minerals in such proportions that the economic long-term sales contracts necessary to obtain project financing could not be procured. Construction of the leach plant therefore allowed development of the mine to proceed. Although the plant took some time to reach design throughput and product specifications, due to the complex and unique nature of the operation, these goals were successfully met and surpassed. This paper describes the physical plant and/or process technology modifications made to mold the main processes-concentrate leaching and filtering, autoclaving and filtration of by-products, and crystallization of salt cake-into an effective, economic operation.IntroductionEquity Silver Mines Limited, a member of the Placer Development Group, owns and operates an open-pit silver mine and related facilities located 37 kilometres southeast of Houston in north-central British Columbia. The mine occupies a 44 I-hectare (1089 acre) site at an elevation of 1300 metres (4265 feet) on the Nechako Plateau. Producing a copper concentrate containing high values of silver and gold, it is the largest silver mine in Canada and one of the largest in the western world. Equity stresses open communications, positive motivation, and production with safety, and achieved the best mine safety record in western Canada in 1984."

Jan 1, 1985

By C. E. Smith, R. J. Inglis, M. I. Brittan, J. H. Schoeman

"AbstractA number of plant-scale cyanidation tests were carried out in an attempt to uncover the causes of fluctuations in gold recovery efficiency. Computer analysis of the results verified that the treatment of reclaimed waste rock material along with normal run-of-mine ore was having an adverse effect on metallurgical efficiency. Mineralogical examinations showed that the free gold particles in the dump material were heavily tarnished or coated (predominantly by hydrated iron oxide), accounting for the lower recoveries. The indications were that the effect could be counteracted somewhat by using higher than normal cyanide and lime reagent concentrations and adequate leaching times. Analysis of the results showed further that leach pulp density was an important operating parameter affecting extraction efficiency. A variable activation energy leaching model provided an extremely good characterization of individual batch leach runs.IntroductionFLUCTUATING METALLURGICAL EFFICIENCY at the gold concentrator of the S.A. Land and Exploration Company Limited (""Sallies"") prompted some plant-scale cyanide leach studies in an endeavour to uncover the causes of the variations in gold recovery."

Jan 1, 1977

By W. C. Risley

IN the year 1933, workings at the No. 12 colliery, New Waterford, of the Dominion Coal Company, Limited, had advanced to a point where additional ventilation would soon be required. Furthermore, development of the mine was being .made to practically double the output of coal. Consequently, authorization was given to sink a shaft to the workings. The location selected is on the west side of the mine, about one and a half miles from the slope mouth and on the Low Point shore, some 250 feet from high-water mark. The cliff at this point is 40 feet high, with the land rising on a slope of about 5 per cent to the shaft. Figure 1 shows the location with reference to the colliery workings. The strata through which the shaft was to be sunk were pretty well known from diamond-drill borings previously made, and it was believed that water would be encountered to a depth of at least 250 feet to 300 feet. It was planned, therefore, to seal-off the water by the pumping of cement grout under high pressure. This method was considered to be the most economical means of handling the water during sinking, and would also result in a permanently dry shaft. Figure 2 shows a cross-section of the strata. The permanent shaft hoist and fan were to be electrically driven, which would necessitate the construction of a transmission line between the colliery and the shaft; therefore, it was arranged that the sinking equipment would have electric drive. As all equipment, materials used in construction, and supplies were to be hauled by truck, a roadway 1,800 feet long was required from the main highway to the site, and as heavy loads would be hauled during the fall, winter, and succeeding spring, this road was ballasted with 18 inches of clinkered material obtained from a burned culm bank one and a half miles distant. Actual field work was begun by the Company's own forces early in October. Work preparatory to sinking-in addition to the roadway and trans-mission line-included the construction of the reinforced-concrete shaft collar and fan drift connection; the permanent timber headframe (which was to be used also as the sinking headframe); the permanent reinforced-concrete building to house the shaft hoist and fan drive; and the erection of temporary buildings and installation of all equipment for sinking and lining the shaft and for cementation.

Jan 1, 1936

By André Bérubé

Since the disappearance of Les Forges du Saint-Maurice at the end of the last century, many historians have taken an interest in the lengthy past of this enterprise. They considered the political, socio-economic, administrative and anecdotal aspects of the industry, but barely dealt with the elements of technology. The purpose of this article is to try to fill this gap (1). Les Forges du Saint-Maurice was an integrated industrial concern, specializing in the production of semi-finished wrought iron and finished cast iron that operated almost without interruption between 1734 and 1883. Les Forges first came into being in 1729, when Montreal merchant Franc;ois Poulin de Francheville submitted to the King of France a request for the right to exploit the bog iron ore deposits on his seigneury of Saint-Maurice. This request, agreed to in 1730, was one of a long series of attempts, previously unsuccessful, to establish a local iron industry in the colony. Several such proposals were held up by a lack of capital from promoters or a too rigid application of the mercantilist policy by the metropolis. In 1730, however, the French minister Maurepas favoured a more liberal policy which would encourage private enterprise. The benefits of an iron industry to the naval construction industry was a factor that caught the attention of administrators. The choice of the site for Les Forges was based on the following factors: - the abundance of surface deposits of bog iron ore in the Saint-Maurice region; - the presence of a vast supply of hardwood and conifers needed in large quantities by this industry; - the proximity of sandstone and limestone deposits, md1spensable materials for the construction and operation of the blast furnace; - the presence of a water stream, with sufficient flow to provide the hydraulic power needed for the operation of the machinery.

Jan 1, 1999

By R. Pelton, Z. Dai, S. Yang

ABSTRACT Hydrophobic polystyrene nanoparticles were evaluated as potential flotation collectors for pentlandite. The flotation of hydrophilic glass beads demonstrated the nanoparticles’ ability to induce flotation. Deposition of nanoparticles on glass surfaces increased the contact angle and enhanced adhesion of the beads to air bubbles. High flotation recoveries were achieved when 5–10% of the bead surfaces were covered with nanoparticles. Surface functionalization—the addition of vinylimidazole to polystyrene nanoparticle surfaces—caused the nanoparticles to selectively deposit onto pentlandite surfaces in the presence of Mg-Si slimes. Ongoing work includes attempts to identify specific applications where nanoparticle collectors might be cost effective. _ KEYWORDS Flotation, Nanoparticle collector, Coverage

Jan 1, 2014

By K. A. Mackinnon

The choice of fan type (axial flow, centrifugal or mixed flow) most suited for a mine ventilation application depends on a number of technical and economic factors. For each project, the relative importance of these factors will vary. It is worthwhile to carry out an assessment on a case by case basis. The paper, by discussing a number of technical and economic factors and their interactions, will provide the ventilation official a methodology to easily and methodically undertake such an assessment.

Aug 1, 2013

By H. C. Boydell

Introduction Situated in the district of South Lorrain, some 16 miles southeast of Cobalt, Ontario, and reached from that centre either by branch line of the T. & N. O. railway or by what, for a mining camp, is a reasonably good road, the Keeley mine, owned by the Keeley Silver Mines,' Ltd., has had its history recorded by C. W. Knight (1). Silver was first discovered in South Lorrain, in Woods' vein, on Keeley property, in 1907, and the Keeley mine has been described by Knight (2) and Bell (3). The total production to February 28th, 1930, has been 10,760,107 ounces of silver and 1,285. 434 pounds (weight) of cobalt.

Jan 1, 1931

By Ben Burger

This paper describes the design, the first three years of operation and optimization of a large, single stage SAG mill at Minera Yanacocha?s Gold Mill facility located in northern Peru. The Gold Mill was commissioned in March 2008 with a 32? x 32? EGL, 16.5MW single stage SAG mill, to process 5 million tonnes per annum high grade oxide Au/Ag ore. Operational control, feed size distribution, grinding media, mill liner, grate and pulp lifter optimisation have allowed the mill to operate 15-30% above design throughput rates, but with a product P80 coarser than design. As part of the optimization, full grinding circuit surveys were conducted. Historical operating data and survey data were analyzed and used to evaluate possible circuit changes and determine alternative operating strategies. A number of changes were implemented which allowed the SAG mill to operate similarly to a large ball mill and achieve finer mill product that was closer to design. This paper summarizes life to date data analysis and improvements made by Minera Yanacocha as well as the grinding circuit optimisation study conducted by Metso Process Technology and Innovation.

Jan 1, 2012

By M. K. Jain, Z. T. Xu, M. Bruhis, V. Hegedekatte

"Strain rate and temperature dependent deformation conditions are present during elevated temperature forming of aluminum and other metallic materials. While many constitutive laws have been proposed to represent such deformation conditions, a closer investigation often reveals their limited applicability in terms of fit to the experimental data, and interpolation within and extrapolation outside of the range of experimental stress-strain curves. This is often because material-specific primary deformation mechanisms of temperature-dependent strain and strain rate hardening are poorly captured. In the present work, the Voce-Kocks constitutive model based on mechanics of dislocations storage and annihilation has been found to be suitable for many metallic materials. The model was modified to include the effect of temperature dependent shear modulus. The modified model is then employed to represent the experimental data obtained from uniaxial tensile tests on AA7075-O sheet at elevated temperatures and strain rates. Also, hot gas bulging tests were conducted to verify the applicability of this model. Further, finite element simulation of the hot gas bulge test was performed by incorporating the model as a user material subroutine. Good general agreement was observed between the experimental and FE model predicted results. Some sources of discrepancy in the prediction are also discussed.INTRODUCTION There has been much interest in light-weighting of automobiles from automotive related industries to reduce overall carbon footprint and increase energy efficiency of the vehicles. Aluminum alloys, and especially the medium-strength 5xxx and 6xxx series alloys, have been the primary focus in the last 3 decades to reach the above environmental goals (Huo, Hou, Zhang, & Zhang, 2016) whereas aerospace industry has traditionally focused on high strength 7xxx series aluminum (Al-Zn-Mg-Cu) alloys for structural components (Deng, Yin, & Huang, 2011). Recently, there has been much interest in high strength 7xxx series aluminum as a replacement for heavier steel automotive structural parts such as A-pillar, B-pillar, side impact beams etc. (Harrison & Luckey, 2014). This is both interesting and challenging since the above aluminum structural parts will need to not only meet impact safety standards but also possess sufficient formability for manufacturing such complex parts. Since the formability of high strength 7xxx series materials is quite poor at room temperature, much interest has focused on improving both formability and final part strength via high rate hot stamping, in-die quenching, and subsequent artificial ageing process steps (Kumar & Ross, 2016)."

Jan 1, 2018

By D. Kovachevich, M. A. Pfeifer

"A t remote locations typical of mines and associated ore processing plants, diesel electric generators are ideally suited for power plants due to their inherent operating flexibility, efficiency and reliability. In recent years rapid escalation in fuel and related transportation costs has made extensive waste heat recovery from generating sets financially attractive to a much greater extent than previously.The paper outlines key considerations during planning and design stages for utilizing the various waste heat sources available to best advantage. Based on two /980 mining projects built in the Canadian Arctic, data is presented on potential operating and capital costs savings. A review of heat balances, engineering flow diagrams and major equipment selections for process and building heating systems utilizing waste heat is included.IntroductionResource projects increasingly occur in remote areas requiring on-site self sufficiency in electrical power generation. For such projects, the low- or medium-speed turbo-charged diesel engine is very often the preferred choice as a prime mover for the generating sets . It is inherently reliable, has good response to load changes and has comparatively high fuel efficiency over a wide load range . From a project execution standpoint, It is capital cost- competitive and procurement lead-time normally ' fits ' within tight schedule constraints. In addition, its potential for waste heat recovery is excellent , particularly in northern climates where space heating requirements are usually substantial, and also where there a re requirements for heat for process and plant services.The high cost of fuel , with add-on transportation costs , provides a major incentive to fully exploit the available waste heat recovery potential o f such installations.As a result of the rapid escalation in the price of petroleum products following major crude oil price increases in 1973 and again in 1978-79, liquid petroleum fuels, having the desirable properties of comparatively high heat content and transportability, are no longer 'cheap' commodities and have become so valuable that industry has widely undertaken serious conservation efforts.Currently, it appears that petroleum cost trends of the 1970s may not continue, at least in the near term, and that we may see somewhat reduced energy costs for a time. In the longer term , and certainly within the life spa n of major projects, however, it is generally believed to be inevitable that these fuels will be increasingly expensive . Energy costs are today a major operating cost for remote minerals processing plants and will remain so for the foreseeable future.In order to meet the economic challenge posed by high energy costs, future projects should be thoughtfully planned from the outset with the goal of minimizing energy requirements and maximizing the use of waste heat recovery to meet such requirements. There is also considerable potential for significant energy savings by retrofitting of existing installations."

Jan 1, 1984

By R. Salimi

Tricalcium aluminate hexahydrate (TCA) is used as filter-aid for security filtration in the Bayer alumina process. TCA is typically produced on-site by mixing Bayer liquor with slaked lime. Specific properties are required from the TCA to ensure adequate filter throughput, lifetime and importantly effective reduction of solid/colloidal impurities from the solution. The effect of reaction time on morphology and particle size distribution of tricalcium aluminate was studied for a batch experiment at simulated process conditions. It was found that reaction time plays a critical role on the morphology, crystal structure (diameter and crystallinity) and particle size distribution. In the early stages of the reaction, nucleation dominates the crystallization process followed by growth dominated by agglomeration up to a mean particle size of 10 µm. The particle morphology shifted from an irregular shape to more spherical throughout the course of the reaction.

Jan 1, 2014

By E. Asselin

Electrochemical polarization experiments were conducted on alloy 625 in ammonia solution between 25 and 225°C and the results were compared with those of an oxygen solubility model. Results confirm that corrosion is under oxygen control, Normalized corrosion rates are determined based on the rate of oxygen diffusion to the corroding surface, and the corrosion rate at 200°C (-9.7 µA.cm-2) is roughly 24 times higher than the corrosion rate at 25°C (0.4 nA,cm-2), An oxygen-solubility model for Supercritical Water Oxidation (SCWO) conditions was generated using the Redlich¬Kwong-Soave (RKS) equation of state, Results of the model confirm many of the experimental observations from SCWO reactors which suggest that corrosion is at a maximum at temperatures just short of the critical point, The RKS/oxygen diffusion model predicts that the corrosion rate at 365° C is ?85 times higher than the corrosion rate at 25' C. Given that a normalized corrosion rate is obtained, this type of model could be useful for selection of SCWO reactor materials.

Jan 1, 2005

By B. R. MacKay

Introduction Of all Canada's mineral resources, its coal deposits have probably received the most continued attention by the Geological Survey since its inception ninety years ago. A casual review of the many geological maps of coal areas by the Geological Survey will show how geological and topographical detail on the maps has gradually increased to meet the ever urgent demands of the mining industry. In the early stages of exploration, the mapping done, especially in the coalfields of the Rocky mountains, was largely of a reconnaissance nature. On these maps the topographical relief, where shown, is indicated by form lines or by hachures, the boundaries of the coal-bearing formations are only approximately defined, and the geological structure of the coal seams is illustrated by one or more generalized cross-sections. Once mining development on a coal area began, there arose a demand for more detailed maps. To meet this need, topographical and geological maps on a scale of one inch to a mile were made, in which the ?topographical relief is shown by contour lines having generally an interval of 100 or 200feet. On the geological maps, the boundaries of the formations are accurately delineated, and the geological structure of the area is illustrated by one or more structure sections drawn across the area, which show the position and attitude of fault lines, the crests and troughs of folds, and the attitude of the various formations (See maps of Costigan Coal Field, 1905, and Cascade Coal Basin, 1907, by D. B. Dowling).

Jan 1, 1932

By Webber. G. R.

Variation in content of some of the major and minor elements in the Lake Dufault granodiorite near Noranda, Quebec has been studied. The element variation and specific gravity data show a pattern consistent with the concept of a concentrically zoned intrusive on the western side of Lake Dufault with a potassium-rich core and a calcium-rich inner zone. The part of the intrusive on the eastern side of Lake Dufault is of more problematical origin, but the suggestion is made that it has resulted from assimilation of volcanic rock by the intrusive. THE purpose of this investigation was to test the application of x-ray fluorescence analysis to the study of variation in chemical com-position of the Lake Dufault granodiorite. The Lake Dufault granodiorite is an intrusive body approximately six miles long by three miles wide located four miles north of Noranda, Quebec. This intrusive is of particular interest because of its -

Jan 1, 1962

By J. G. Ross

IN the paper entitled Block Caving at the King Mine (1), which was presented at the Annual General Meeting held in April, 1934, at Quebec, it was pointed out that, owing to certain conditions and financial restrictions, it was advisable to provide a temporary shaft. This was raised from the )00-ft. level to the bottom of the pit, and a 45-degree incline track was constructed up the face of the pit to surface. The temporary shaft and incline were within the ore-body, but were to be used only until such time as the new shaft-the subject of this paper-could be sunk and made ready for operation. After a careful study had been made of all available information pertaining to the ore-body, including examination of diamond-drill core records and geological data, a shaft location was selected well outside the ore-body. Further, since the crusher and dryer buildings are located over part of the ore-body, it was necessary to plan the removal of these buildings and to construct a new crushing and drying plant. This, and the new shaft, must operate in conjunction with the present mill and rock storage bin, which would continue robe used as formerly. No part of this programme, with the exception of drifting toward the shaft site, was started prior to 1937. More than usual detail on technical features is given in this paper in the hope that some parts of it may be of assistance to other members of the Institute who have to undertake somewhat similar work. The engineering and operating staff designed and supervised the work, while at the same time carrying on regular production in four mines at the rate of 12,000 tons of rock mined per day, the output at the King mine being at the rate of 140 tons per hour. No additional engineers were required.

Jan 1, 1939